Manualios.com

Cisco PA-2E3 Installation And Configuration Manual

Cisco PA-2E3 Manual Online:

4.05, 1238 votes
Cisco PA-2E3 User Manual
Cisco PA-2E3 User Guide
Cisco PA-2E3 Online Manual

Text of Cisco PA-2E3 User Guide:

  • Cisco PA-2E3, Configuring Cyclic Redundancy Checks PA-E3 Serial Port Adapter Installation and Configuration 8-10 Specifying E3 Framing In interface configuration mode, specify E3 framing by entering the framing {g751 | bypass} configuration subcommand, as in the following example: router(config-if)# framing g751 Use the no form of this command to return to the default, which is G.751 framing. Note If you use the bypass option, scrambling must be set to the default, disabled; the DSU mode must be set to the default, 0; and the DSU bandwidth must be set

  • Cisco PA-2E3, CHAPTER Cisco 7200 Series and the PA-E3 5-1 5 Cisco 7200 Series and the PA-E3 This chapter provides information on the PA-E3 serial port adapter and its use in Cisco 7200 series routers. This chapter contains the following sections: • Overview, page 5-1 • Removing a Port Adapter, page 5-2 • Installing a Port Adapter, page 5-3 Overview The PA-E3 can be installed in any available port adapter slot in Cisco 7200 series routers (which consist of the two-slot Cisco 7202, four-slot Cisco 7204 and Cisco 7204VXR, and the six-slot Cisco 7206 and Cisco 7206VXR). Figure 5-1 shows a one-port PA-E3 installed in port ad

  • Cisco PA-2E3, Cisco 7200 Series and the PA-E3 5-3 Installing a Port Adapter Caution Always handle the port adapter by the carrier edges and handle; never touch the port adapter’s components or connector pins. (See Figure 5-3.) Figure 5-3 Handling a Port Adapter Step 6 Place the port adapter on an antistatic surface with its components facing upward, or in a static shielding bag. If the port adapter will be returned to the factory, immediately place it in a static shielding bag. This completes the procedure for removing a port adapter from a Cisco 7200 series router. Installing a Port Adapter Following is the procedure for installing a new port adapter in a Cisco 7200 series router: Step 1 Attach an E

  • Cisco PA-2E3, Software and Hardware Requirements PA-E3 Serial Port Adapter Installation and Configuration 2-2 Software and Hardware Requirements Table 2-1 lists the minimum Cisco IOS software release required to use the one-port PA-E3 and two-port PA-2E3 in supported router platforms. Table 2-1 PA-E3 and PA-2E3 Software Requirements Caution The VIP2 requires that the host Cisco 7000 series router have the RSP7000 and RSP7000CI installed. The VIP2 does not operate properly with the Route Processor (RP), Switch Processor (

  • Cisco PA-2E3, Checking the Configuration PA-E3 Serial Port Adapter Installation and Configuration 8-16 Following is an example of the show version command used with a Cisco 7500 series system: router# show version Cisco Internetwork Operating System Software IOS (tm) GS Software, Version 11.1(16)CA Synced to mainline version: 11.1(10.5) Copyright (c) 1986-1997 by cisco Systems, Inc. Compiled Thu 22-May-97 14:32 Image text-base: 0x600108E0, data-base: 0x60A00000 ROM: System Bootstrap, Version 5.3.2(3.2) [kmac 3.2], MAINTENANCE INTERIM SOFTWARE ROM: GS Software, Version 11.1(8)CA, EARLY DEPLOYMENT

  • Compliance Information PA-E3 Serial Port Adapter Installation and Configuration 2-6 • Handle carriers by available handles or edges only; avoid touching the printed circuit boards or connectors. • Place a removed component board-side-up on an antistatic surface or in a static shielding container. If you plan to return the component to the factory, immediately place it in a static shielding

  • Cisco PA-2E3, Preparing for Installation 2-5 Electrical Equipment Guidelines Varning! Denna varningssymbol signalerar fara. Du befinner dig i en situation som kan leda till personskada. Innan du utför arbete på någon utrustning måste du vara medveten om farorna med elkretsar och känna till vanligt förfarande för att förebygga skador. Se förklaringar av de varningar som förkommer i denna publikation i dokumentet Regulatory Compliance and Safety Information (Efterrättelse av föreskrifter och säkerhetsinformation), vilket medföl

  • Cisco PA-2E3, VIP2 and the PA-E3 3-3 Overview Figure 3-2 shows two one-port E3 port adapters installed in port adapter slots 0 and 1, on a VIP2-50. Figure 3-2 VIP2-50 with One-Port PA-E3 Port Adapters in Port Adapter Slots 0 and 1 Depending on the circumstances, you might need to install a new port adapter on a VIP2 motherboard or replace a failed port adapter in the field. In either case, you need a number 1 Phillips screwdriver, an antistatic mat on which you can place the removed interface processor, and an antistatic container in which you can place a failed port adapter for shipment back to the factory. Note The

  • CHAPTER Catalyst RSM/VIP2 and the PA-E3 4-1 4 Catalyst RSM/VIP2 and the PA-E3 This chapter provides information on the PA-E3 serial port adapter and its use on the Catalyst RSM/VIP2 in the Catalyst 5000 family switches. This chapter contains the following sections: • Overview, page 4-1 • Removing a Port Adapter, page 4-3 • Installing a Port Adapter, page 4-4 Overview The PA

  • Cisco PA-2E3, Cisco 7100 Series and the PA-E3 7-3 Installing a Port Adapter Figure 7-3 Handling a Port Adapter Step 6 Place the port adapter on an antistatic surface with its components facing upward, or in a static shielding bag. If the port adapter will be returned to the factory, immediately place it in a static shielding bag. Step 7 Install a blank port adapter or replacement port adapter to maintain proper flow of cooling air across the internal components. For procedures on how to install a port adapter, see the

  • Cisco PA-2E3, 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.com Cisco Systems, Inc. Corporate Headquarters Tel: 800 553-NETS (6387) 408 526-4000 Fax: 408 526-4100 PA-E3 Serial Port Adapter Installation and Configuration Product Number: PA-E3(=) and PA-2E3(=) Platforms Supported: Cisco 7500 Series, Cisco 7000 Series, VIP2, Cisco 7200 Series, Cisco uBR7200 Series, Cisco 7100 Series, Catalyst 5000 Family Switches Access Registrar, AccessPath, Any to Any, AtmDirector, CCDA, CCDE, CCDP, CCIE, CCNA, CCNP, CCSI, CD-PAC, the Cisco logo, Cisco Certified Internetwork Expert logo, CiscoLink, the Cisco Manag

  • Cisco PA-2E3, Preface v Preface This preface describes how to find additional information on the PA-E3 serial port adapter and other Cisco products, services, and documentation. This preface contains the following sections: • Objectives, page v • Organization, page v • Related Documentation, page vi • Cisco Connection Online, page viii • Documentation CD-ROM, page viii Objectives This document describes how to install and configure the PA-E3 serial port adapter (PA-E3[=] and PA-2E3[=]) in the following platform

  • Cisco PA-2E3, Installing a Port Adapter PA-E3 Serial Port Adapter Installation and Configuration 3-6 Figure 3-5 Aligning a Port Adapter in a Port Adapter Slot Caution To prevent jamming the carrier between the upper and lower edges of the port adapter slot and to ensure that the edge connector at the rear of the port adapter mates with the connector at the rear of the port adapter slot, make certain that the leading edges of the carrier are between the upper and lower slot edges, as shown in the cutaway in Figure 3-5. Caution To ensure a positive ground attachment between

  • Cisco PA-2E3, Overview 1-3 PA-E3 Serial Port Adapter Features PA-E3 Serial Port Adapter Features The PA-E3 serial port adapter has the following features: • Single-width port adapter for the VIP2 in all Cisco 7000 series and Cisco 7500 routers, and in Cisco 7100 series, Cisco 7200 series, and Cisco uBR7200 series routers • Single-width port adapter for the Catalyst RSM/VIP2 in the Catalyst 5000 family switches • Single- or double-port E3 rate (34 Mbps) connectivity • Full-duplex synchronous serial E3 interface • High-speed High-Level Data Link Control (HDLC) data • Integrate

  • Cisco PA-2E3, CHAPTER Cisco 7100 Series and the PA-E3 7-1 7 Cisco 7100 Series and the PA-E3 This chapter provides information on the PA-E3 serial port adapter and its use in the Cisco 7100 series routers. This chapter contains the following sections: • Installation Overview, page 7-1 • Removing a Port Adapter, page 7-2 • Installing a Port Adapter, page 7-3 Installation Overview The PA-E3 can be installed in port adapter slot 3 in Cisco 7120 series routers and in port adapter slot 4 in Cisco 7140 series routers. Figure 7-1 shows port adapter slot 3 of a Cisco 7120 series router. Figure 7-2 shows port adapter slot

  • Cisco PA-2E3, Removing a Port Adapter PA-E3 Serial Port Adapter Installation and Configuration 7-2 Figure 7-2 Cisco 7140 Series Router—Port Adapter Slot 4 Location Depending on your circumstances, you might need to install a new port adapter in a Cisco 7100 series router or replace a failed port adapter in the field. All port adapters available for the Cisco 7100 series connect directly to the router and are locked into position by a locking tab with two screws (see Figure 7-1 or Figure 7-2). You need a number 2 Phillips screwdriver to loosen

  • Cisco PA-2E3, Cisco uBR7200 Series and the PA-E3 6-3 Removing a Port Adapter • For a Cisco uBR7223, place the port adapter lever in the unlocked position. (See Figure 6-3.) Figure 6-3 Placing the Port Adapter Lever in the Unlocked Position —Cisco uBR7223 Shown Step 3 Grasp the handle on the port adapter and pull the port adapter from the router midplane, about halfway out of its slot. If you are removing a blank port adapter, pull the blank port adapter completely out of the chassis slot. Note As you disengage the port adapter from the midplane, OIR administratively shuts down all active interfaces on the port adapter. Step 4 With the port adapter halfway out of the slot, disconnect all cables from t

  • Cisco PA-2E3, Overview 1-5 Interoperability Guidelines for PA-E3 DSUs On a single PA-E3, there are one or two serial E3 ports, each with two connectors (receive and transmit), where you connect the Cisco 75-ohm coaxial cable. The 75-ohm coaxial cable (Cisco part number CAB-ATM-DS3/E3) for the PA-E3 is available only from Cisco Systems; it is not available from outside commercial cable vendors. The Cisco E3 75-ohm coaxial cable, which comes with an attached ferrite sleeve (see Figure 1-5), is available only in 10-foot (3.05-meter) lengths. The typical maximum distance between stations for E3 transmissions is 1300 feet (396 meters). Note For E3 (75-ohm) connections, you must have ferrite

  • Cisco PA-2E3, Identifying Port Adapter Slot and PA-E3 Interface Port Numbers PA-E3 Serial Port Adapter Installation and Configuration 8-6 Figure 8-4 Serial Port Adapters in the Catalyst 5509 You can identify interface ports by physically checking the port-adapter/interface port location on the back of the router or by using show commands to display information about a specific interface or all interfaces in the router. Cisco 7100 Series Ports In the Cisco 7100 series routers, the slot number is the location in the chassis where the interface resides and the port number is the physical port. Interfaces in the Cisco IOS software are identified by a type, slot number, an

Related Products and Documents (Adapter):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 GE J1458W Manuale utente ge/j1458w-2NL.pdf 16 Sep 2023 84 4.96 Mb
2 Makita 5007NB-A Instruction manual makita/5007nb-a-MG7.pdf 28 Aug 2023 16
3 Philips 27HT4000D Operation & user’s manual philips/27ht4000d-12Z.pdf 06 Oct 2022 25 8.94 Mb
4 Philips 6916665PH Brochure philips/6916665ph-552.pdf 15 Dec 2023 3 1.99 Mb
5 Panasonic FP-D250 User manaul panasonic/fp-d250-2WY.pdf 19 Sep 2022 663
6 Oki 10i Help manual oki/10i-I83.pdf 15 Mar 2023 40

Similar Resources:

  • BT

    Vision

    (22 pages)
    Job No. 1931Client BTProject BT Vision guide Cardinal v8Revision 3-DRModified 30/10/13Created 15/10/13To set up, follow this guide or the online video at bt.com/help/tv/setupguideUser GuideBT TVKeep this guide somewhere safeYou might need it from time to time.Easy set-up …
  • Keysight

    U1117A

    (10 pages)
    Keysight U1117A IR-to-Bluetooth AdapterOperating InstructionsThe Keysight U1117A Infrared (IR)-to-Bluetooth®1 adapter is designed to be used with the Keysight U1200 Series handheld meters. The U1117A adapter enables you to connect the handheld meter to the Keysight U1115A remote logging display or Windows PC/Android devices/iOS devices via the Keysight mobi …
  • 1Mii

    B10

    (13 pages)
    B10 User GuideGet paired with your PC/Mac1.Plug B10 into USB port on your PC/Mac.2.Press and hold the multi-function button on B10 for 2~3 seconds to enter paring modethe LED indicator will alternatively flashes blue and red.3.Please ensure your Bluetooth headphone in paring mode.4.Get your Bluetooth headphone close to B10 audio adapter to complete paring(th …
  • Alpine

    eX-10

    (8 pages)
    Apple, the Apple logo, iPod and iTunes are registered trademarks of Apple Inc. The Bluetooth logo is owned by the Bluetooth SIG, Inc. and any use of such marks by Alpine Electronics, Inc. is under license. Product information listed in this guide is based upon current information at the time of printing, but cannot be guar-anteed. All designs, features, and …
  • Baby Jogger

    City Mini GT

    (16 pages)
    Read these instructions carefully before use and keep them for future reference. Your child’s safety may be affected if you do not follow these instructions.www.babyjogger.comCITY MINI GT ASSEMBLY INSTRUCTIONS This product complies with BS EN 1888:2003 inc. A1,2,3: 2005 …

Comments, Questions and Opinions: