Manualios.com

Cisco PA-T3 Installation And Configuration Manual

Cisco PA-T3 Manual Online:

3.4, 1189 votes
Cisco PA-T3 User Manual
Cisco PA-T3 User Guide
Cisco PA-T3 Online Manual

Text of Cisco PA-T3 User Guide:

  • Cisco PA-T3, CHAPTER VIP2 and the PA-T3 Port Adapter 3-1 3 VIP2 and the PA-T3 Port Adapter This chapter provides information on the PA-T3 port adapter and its use on the VIP2 in Cisco 7000 series and Cisco 7500 series routers. This chapter contains the following sections: • Overview, page 3-1 • Removing a Port Adapter, page 3-4 • Installing a Port Adapter, page 3-5 Overview The PA-T3 serial port adapter is used on the VIP2 in Cisco 7000 series and Cisco 7500 series routers and can be installed in either port adapter slot 0 or slot 1 on the VIP2 motherboar

  • Cisco PA-T3, Catalyst RSM/VIP2 and the PA-T3 Port Adapter 4-3 Removing a Port Adapter When only one port adapter is installed on a Catalyst RSM/VIP2, you must use a blank port adapter to fill the empty slot. This allows the Catalyst RSM/VIP2 and the Catalyst RSM/VIP2 chassis to conform to electromagnetic interference (EMI) emissions requirements and encourages air to flow through the chassis properly. If you plan to install a new port adapter, you must first remove the blank port adapter. Removing a Port Adapter Following is the standard procedure for removing any type of port adapter on the Catalyst RSM/VIP2: Step 1 Att

  • Cisco PA-T3, Overview PA-T3 Serial Port Adapter Installation and Configuration 4-2 Figure 4-1 Catalyst RSM/VIP2-15 or Catalyst RSM/VIP2-40 with One-Port PA-T3 Serial Port Adapters in Port Adapter Slots 0 and 1 Note Port adapters have a handle attached, but this handle is not shown to allow a full view of detail on each port adapter’s faceplate. Depending on the circumstances, you might need to install a new port adapter on a Catalyst RSM/VIP2 motherboard or replace a failed port adapter in the field. In either case, you need a number 1 Phillips screwdriver, an antistatic mat on which you can place the removed interface processor, and a

  • Cisco PA-T3, Cisco uBR7200 Series and the PA-T3 Port Adapter 6-5 Installing a Port Adapter Figure 6-6 Placing the Port Adapter Retention Clip in the Locked Position—Cisco uBR7246 Shown • For a Cisco uBR7223, place the port adapter lever in the locked position. (See Figure 6-7.) Figure 6-7 Placing the Port Adapter Lever in the Locked Position—Cisco uBR7223 Shown Note If the port adapter lever does not move to the locked position, the port adapter is not completely seated in the midplane. Carefully pull the port adapter halfway out of the slot, reinsert it, and move the port adapter lever to the locked position. This completes the procedure for installi

  • Cisco PA-T3, Software and Hardware Requirements PA-T3 Serial Port Adapter Installation and Configuration 2-2 Software and Hardware Requirements Table 2-1 lists the minimum Cisco IOS software release required to use the PA-T3 and the PA-2T3 serial port adapters in supported router platforms. Table 2-1 PA-T3 Port Adapter Software Requirements Caution The VIP2 requires that the host Cisco 7000 series router have the RSP7000 and RSP7000CI installed. The VIP2 does not operate properly with the Route Processor (RP), Switch Processor (SP), or Silicon Switch Processor (SSP) installed in the host Cisco series router. The PA-T3 serial port adapter is considered a high-bandwidth port adapter;

  • Cisco PA-T3, Checking the Configuration PA-T3 Serial Port Adapter Installation and Configuration 8-16 The following example of the show interfaces type slot/port command shows all of the information specific to the serial PA-T3 port (interface port 0) in port adapter slot 2: router# show interfaces serial 2/0 Serial2/0 is up, line protocol is up Hardware is M1T-T3 pa MTU 4470 bytes, BW 44210 Kbit, DLY 200 usec, rely 255/255, load 1/255 Encapsulation HDLC, loopback not set, keepalive not set Last input 00:00:01, output 00:00:03, output hang ne

  • Preparing for Installation 2-3 PA-T3 Port Adapter LEDs Note The VIP2 and Catalyst RSM/VIP2 supports online insertion and removal (OIR), but individual port adapters do not. To replace port adapters in the Cisco 7000 series and Cisco 7500 series routers, and the Catalyst 5000 series switches, you must first remove the VIP2 or Catalyst RSM/VIP2 from the chassi

  • PA-T3 Port Adapter LEDs PA-T3 Serial Port Adapter Installation and Configuration 2-4 Figure 2-1 LEDs on the PA-T3 Serial Port Adapter—Partial Front View The PA-2T3 has one status LED and six uplink port status LEDs (RCLK, FERF, OOF, AIS, RL, and LL) for each serial PA-T3 port. (See Figure 2-2.) Figure 2-2 LEDs on the PA-2T3 Serial Port Adapter—Partial Fro

  • Cisco PA-T3, Overview PA-T3 Serial Port Adapter Installation and Configuration 3-2 Figure 3-1 VIP2-15 or VIP2-40 with One-Port PA-T3 Serial Port Adapters in Port Adapter Slots 0 and 1 Note Port adapters have a handle attached, but this handle is not shown to allow a full view of detail on each port adapter’s faceplate. 24335 PA-T3 in port adapter slot 0 PA-T3 in port adapter slot 1 Port adapter handles not shown Bus connector DRAM SIMMs SRAM DIMM U5 CPU U6 U2 U4 Boot ROM ENABLED RCVR XMTR RCLK AIS FERF RL OOF LL DS3 SERIAL ENABLED RCVR XMTR

  • Preface v Preface This preface describes how to find additional information on the PA-T3 and PA-2T3 serial port adapters and other Cisco products, services, and documentation. This preface contains the following sections: • Objectives, page v • Organization, page v • Related Documentation, page vi • Cisco Connection Online, page vii • Cisco Documentation CD-ROM, page

  • Overview 1-3 Management Information Base • Single-width port adapter for the Catalyst RSM/VIP2 in all Catalyst 5000 series switches • Single- or double-port T3 rate (45 Mbps) connectivity • Full-duplex synchronous serial DS3 interface • High-speed High-Level Data Link Control (HDLC) data • Integrated data service unit (DSU) functionality • Suppor

  • Cisco PA-T3, Safety Guidelines PA-T3 Serial Port Adapter Installation and Configuration 2-6 Safety Guidelines Following are safety guidelines that you should follow when working with any equipment that connects to electrical power or telephone wiring. Warning This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. To see translations of

  • Cisco PA-T3, Configuring the PA-T3 Interfaces 8-21 Using show Commands to Display Interface and System Information To determine which type of port adapter is installed in your system, use the show diag slot command. Specific port adapter information is displayed, as shown in the following example of a one-port PA-T3 serial port adapter in chassis slot 3 on a Cisco 7200 series router: router# show diag 3 Slot 3: PA-T3 PA port adapter, 1 port Port adapter is analyzed Port adapter insertion time 3d19h ago Hardware revision 0.1 Board revision UNKNOWN Serial nu

  • Cisco PA-T3, Configuring the PA-T3 Interfaces 8-9 Shutting Down an Interface The example that follows is for Cisco 7100 series, Cisco 7200 series, or Cisco uBR7200 series routers: Router# show interfaces serial 1/0 Serial 1/0 is administratively down, line protocol is down Hardware is M1T-T3 pa [display text omitted] To verify that new interfaces are now in the correct state (shutdown) on a VIP2, use the show interfaces serial slot/port adapter/interface command to display the specific interface, or use the show interfa

  • Cisco PA-T3, Shutting Down an Interface PA-T3 Serial Port Adapter Installation and Configuration 8-8 Step 4 Enter the shutdown command as follows: Router(config-if)# shutdown Step 5 To shut down additional interfaces, enter the slot/port address (or slot/port address/interface port for a VIP2) of each additional interface followed by the shutdown command. When you have entered all the interfaces to be shut down, press Ctrl-Z (hold down the Control key while you press Z) or enter end to exit configuration mode and return to the

  • Cisco PA-T3, Cisco Documentation CD-ROM viii PA-T3 Serial Port Adapter Installation and Configuration Available 24 hours a day, 7 days a week, CCO provides a wealth of standard and value-added services to Cisco’s customers and business partners. CCO services include product information, product documentation, software updates, release notes, technical tips, the Bug Navigator, configuration notes, brochures, descriptions of service offerings, and download access to public and authorized files. CCO serves a wide variety of users through two interfaces that are updated and enhanced simultaneously: a character-based version and a multimedia version th

  • Cisco PA-T3, Identifying Port Adapter Slot and T3 Interface Port Numbers PA-T3 Serial Port Adapter Installation and Configuration 8-6 Figure 8-4 PA-T3 Serial Port Adapter in the Catalyst 5509 You can identify interface ports by physically checking the port-adapter/interface port location by using show commands to display information about a specific interface or all interfaces in the router. Cisco 7100 Series Ports In the Cisco 7100 series routers, the slot number is the location in the chassis where the interface resides and the port number is the physical port. Interfaces in the Cisco IOS s

  • Cisco PA-T3, Removing a Port Adapter PA-T3 Serial Port Adapter Installation and Configuration 6-2 Note Cisco uBR7200 series routers support OIR; therefore, you do not have to power down the router when removing and replacing a PA-T3 port adapter. When a port adapter slot is not in use, blank port adapters must fill empty slots to allow the router to conform to EMI emissions requirements and to allow proper airflow across the port adapters. If you plan to install a new port adapter in a slot that is not in use, you must first remove the blank port adapter. Rem

  • Cisco PA-T3, Preparing for Installation 2-7 Electrical Equipment Guidelines Aviso Este símbolo de aviso indica perigo. Encontra-se numa situação que lhe poderá causar danos físicos. Antes de começar a trabalhar com qualquer equipamento, familiarize-se com os perigos relacionados com circuitos eléctricos, e com quaisquer práticas comuns que possam prevenir possíveis acidentes. Para ver as traduções dos avisos que constam desta publicação, consulte o documento Regulatory Compliance and Safety Information (Informação de Segurança e Disposições Reguladoras) que acompanha este dispositivo. ¡Advertencia! Est

  • Cisco PA-T3, VIP2 and the PA-T3 Port Adapter 3-7 Installing a Port Adapter This completes the procedure for installing a port adapter on a VIP2. Proceed to Chapter 8, “Configuring the PA-T3 Interfaces,” for information on how to configure your port adapter interfaces.

Related Products and Documents (Adapter):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 IFM Electronic VNB001 Operating instructions manual ifm-electronic/vnb001-WB1.pdf 17 Nov 2023 27
2 Black & Decker Dustbuster AV1210 Manual  black-decker/dustbuster-av1210-WW5.pdf 03 Jan 2024 12
3 Samsung SGH-Z170 Operation & user’s manual samsung/sgh-z170-6E6.pdf 08 Sep 2023 43
4 Hitachi P50A402 Brochure hitachi/p50a402-M72.pdf 18 Nov 2022 1 0.85 Mb
5 Motorola VISAR Operating instructions manual motorola/visar-592.pdf 24 Jul 2022 32
6 Panasonic DMP-BDT500 Operating instructions manual panasonic/dmp-bdt500-8YB.pdf 07 Oct 2023 48 2.43 Mb

Similar Resources:

  • i-tec

    C31METAL25LAN

    (32 pages)
    P/N: C31METAL25LANUser guide • Gebrauchsanweisung • Mode d’emploi Manual de instrucciones • Manuale • Uživatelská příručka Instrukcje obsługi • Užívateľská príručka • Vartotojo vadovasHandleiding USB-C GIGABIT ETHERNET ADAPTER …
  • Cateye

    EC3600E

    (26 pages)
    RRECUMBENT TYPECateye ergociserOPERATING INSTRUCTIONSEC-36OORECUMBENT TYPEREC-3600CATEYE ERGOCISERMODEL : EC-3600POWER : DC 12VPOWER CONSUMPTION:       MAX 15WUSE THE SPECIFIEDCAT EYE ERGOCISERAC ADAPTER ONLY.SERIAL No.CO.,LTD.MADE IN JAPAN …
  • Regal

    Century VLink

    (50 pages)
    VLink A wireless adapter for use with Century VGreen Variable Speed MotorsInstallation and User ManualStock Number: VL100MCIM16001E 9975E Century VLink Installation Manual -- MCIM16001E 9975E Century VLink Installation Manual …
  • Digitus

    DA-71101

    (10 pages)
    SATA TO IDE, SATA TO SATA, SSD/HDD MOUNTING FRAME Quick Installation Guide DA-71101: 9.5mm, IDE  DA-71103: 9.5mm, SATA DA-71100: 12.7mm, IDE  DA-71102: 12.7mm, SATA …
  • Belkin

    F5U004

    (15 pages)
    Installation for the F5U004 in Windows 2000If you Downloaded the Software off the website, it’s a compressed file and needs to beunzipped before running this setup.Steps:1. Connect the direct connect to your PC. This window Should Appear.2. Search for a suitable driver… Should already be selected Go ahead and Click Next. …
  • ActionTec

    MegaPlug AV

    (2 pages)
    Note: An Ethernet port looks similar to a phone port but is slightly larger.1Connect the Adapter to a PC or Modem/RouterStep1 Get one MegaPlug AV200 Mbps Ethernet Adapter fromthe box.Step5 Plug the other end of theEthernet Cable into an OPENEthernet Port on your Modem orRouter.Step4 Plug the MegaPlugAdapter into a Power Outlet.Do NOTplug the Adapter into apo …

Comments, Questions and Opinions: