Manualios.com

Cisco IAD2435-8FXS Quick Start Manual

Cisco IAD2435-8FXS Manual Online:

3.05, 2940 votes
Cisco IAD2435-8FXS User Manual
Cisco IAD2435-8FXS User Guide
Cisco IAD2435-8FXS Online Manual

Text of Cisco IAD2435-8FXS User Guide:

  • 32 To configure basic T1/E1 controller settings to support PPP, High-Level Data Link Control (HDLC), or Frame Relay (FR), follow these steps, beginning in global configuration mode: Configuring Digital Voice To configure basic T1/E1 controller settings to support PPP, HDLC, or FR, follow these steps, beginning in global configuration mode: Command Description Step 1 Router(config)# c

  • Cisco IAD2435-8FXS, 13 Figure 11 Cisco IAD2435 IAD Rack-Mounting with Back Panel Forward Step 2 Install the chassis in the rack, using screws that you purchase. Setting the Chassis on a Desktop You can set the Cisco IAD2430 series IADs on a desktop. To place the Cisco IAD2430, Cisco IAD2431, or Cisco IAD2432 IAD on a desktop follow these steps: Step 1 Verify that a suitable AC power outlet is available. Caution Do not plug this unit into an AC outlet that does not have a UL-certified receptacle that is properly tied into the building ground. Step 2 Place the four rubber feet (from the

  • Cisco IAD2435-8FXS, 9 When mounting this unit in a partially filled rack, load the rack from the bottom to the top with the heaviest component at the bottom of the rack. If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing the unit in the rack. Statement 1006 Warning There is the danger of explosion if the battery is replaced incorrectly. Replace the battery only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions. Statement 1015 Warning Take care when connecting units to the supply circ

  • Cisco IAD2435-8FXS, 26 Figure 27 Connecting the External Power Supply to the Cisco IAD2435 IAD The following message appears at the end of the bootup messages: --- System Configuration Dialog --- Continue with configuration dialog? [yes/no]: Step 3 Enter no to proceed with manual configuration using the command-line interface (CLI): Would you like to enter the initial configuration dialog? [yes/no]: no Would you like to terminate autoinstall? [yes] Step 4 Press Return to terminate autoinstall and continue with manual configuration. Several messages appear, ending with lines similar to the following: Copyright (c) 2008

  • Cisco IAD2435-8FXS, 28 11 Performing the Initial Configuration This section describes how to configure the Cisco IAD2430 series IADs to perform basic communication functions. You may initially configure your router by using the Cisco IOS command-line interface (CLI) or by using the setup command facility. To create the initial configuration, the setup command facility prompts you for basic information about your router and network. Cisco IOS CLI To configure the initial router settings by using the Cisco IOS CLI, follow these steps

  • Cisco IAD2435-8FXS, 3 Figure 1 Cisco IAD2430 Series Front Panel (Cisco IAD2432-24FXS IAD shown) Figure 2 Cisco IAD2435 IAD Front Panel Figure 3 identifies the different back panels and features of the Cisco IAD2430 series models. Figure 4 shows the back panel and features of the Cisco IAD2432-24FXS IAD model. Figure 5 shows the back panel and features of the Cisco IAD2435-8FXS IAD model. Note Not all models have all functions. 88839 CISCO IAD2400 231872 Cisco IAD2400 SERIES OK 0/0 0/1 FE T1/E1 FXS CD AL 2/0 2/1 2/2 2/3 2/4 2/5 2/6 2/7

  • 18 Grounding the Chassis Use the information in this section to provide proper ground for the Cisco IAD2400 series IADs. You must connect the chassis to a reliable earth ground; the ground wire must be installed in accordance with local electrical safety standards. • For NEBS-compliant grounding, use size AWG 6 (13 mm 2 ) wire and the ground lug provided in the accessory kit. • For NEC-com

  • Cisco IAD2435-8FXS, 4 Figure 3 Back Panels for the Cisco IAD2430 Series Models Cisco IAD2430-24FXS IAD • RJ-21 analog voice interface • T1/E1 ports: none • FE ports: 2 • External flash memory Cisco IAD2431-8FXS IAD • RJ-21 analog voice interface • T1/E1 ports: 1 • FE ports: 1 • WIC/VIC option • External flash memory Cisco IAD2431-16FXS IAD • RJ-21 analog voice interface • T1/E1 ports: 1 • FE ports: 2 • WIC/VIC option • External flash memory Cisco IAD2431-1T1E1 IAD • T1/E1 ports: 2 • FE por

  • Cisco IAD2435-8FXS, QUICK START GUIDE Cisco IAD2430 Series Integrated Access Devices INCLUDING LICENSE AND WARRANTY 1 Cisco 90-Day Limited Hardware Warranty Terms 2 Obtaining Documentation and Submitting a Service Request 3 Equipment, Tools, and Accessories 4 Product Serial Number Location 5 Accessibility 6 Safety Information 7 Installing the Chassis 8 Installing a WAN or Voice Interface Card 9 Connecting Cables 10 Powering On the Cisco IAD 11 Performing the Initial Configuration

  • 30 to configure each interface on the system Would you like to enter basic management setup? [yes/no]: yes Step 5 Enter a hostname for the router (this example uses Router): Configuring global parameters: Enter host name [Router]: Router Step 6 Enter an enable secret password. This password is encrypted (more secure) and cannot be seen when viewing the configura

  • Cisco IAD2435-8FXS, 22 Connecting WAN and Voice Cables WAN and voice cables and connections are described in Table 3 and shown in Figure 21. Figure 21 WAN and Voice Connections Note If you have specified the use of a private line automatic ringdown (PLAR) off-premises extension (OPX) connection mode for an FXO voice port (with loop resistance less than 8000 Ohm), you must ensure that the soft-offhook option is enabled on the port. This option allows a stepped offhook resistance during seizure which avoids overloading the circuit during offhook in the e

  • Cisco IAD2435-8FXS, 29 You are now in privileged EXEC mode. Note You must change the username and password before you log off the router. You cannot use the username cisco or password cisco after you log off from this session. Step 5 To change the username and password, enter the following at the prompt: username username privilege 15 secret 0 password Username and password are the username and password that you wish to use. Note Use the copy running-config startup-config command at the privileged EXEC mode prompt (Router#) to save the configuration to NVRAM.

  • Cisco IAD2435-8FXS, 20 • VWIC-2MFT-T1 • VWIC-2MFT-E1 Note Contact your Cisco account representative for the most recent, supported cards. For detailed information on installing and connecting interface cards, see the following URL: http://www.cisco.com/en/US/products/hw/modules/ps2641/prod_installation_guides_list.html Caution WAN and voice interface cards do not support online insertion and removal (OIR, or hot swapping). Before inserting a card into the Cisco IAD chassis, you must turn off electrical power and disconnect network cables. Always use an ESD-preventive wrist strap when handl

  • Cisco IAD2435-8FXS, 10 Warning Ultimate disposal of this product should be handled according to all national laws and regulations. Statement 1040 Warning Before opening the unit, disconnect the telephone-network cables to avoid contact with telephone-network voltages. Statement 1041 Warning This equipment must be installed and maintained by service personnel as defined by AS/NZS 3260. Incorrectly connecting this equipment to a general-purpose outlet could be hazardous. The telecommunications lines must be disconnected 1) before unplugging the main power connector or 2) while the housing is open, or both. Stateme

  • Cisco IAD2435-8FXS, 19 Figure 17 Cisco IAD2435 IAD Chassis Ground Connection Using Ground Lug Figure 18 Chassis Ground Connection Using Ring Terminal Step 5 Connect the other end of the ground wire to a grounding point at your site. 8 Installing a WAN or Voice Interface Card The Cisco IAD2430 series IADs include a slot for a WAN interface card (WIC) or voice interface card (VIC). Note The Cisco IAD2435 router is a fixed-configuration router and does not support interface cards. Releases of the Cisco IAD2430 series I

  • Cisco IAD2435-8FXS, 8 Warning Before performing any of the following procedures, ensure that power is removed from the DC circuit. Statement 1003 Warning To prevent accidental discharge in the event of a power line cross, route on-premise wiring away from power cables and off-premise wiring, or use a grounded shield to separate the on-premise wiring from the power cables and off-premise wiring. A power line cross is an event, such as a lightning strike, that causes a power surge. Off-premise wiring is designed to withstand power line crosses. On-premise wiring is protected from power line cro

  • Cisco IAD2435-8FXS, 33 For additional information about configuring specific features, see the following references: • For PPP, HDLC, or FR, consult the online master index for the Cisco IOS release that you are using. • For loopback diagnostics, or for configuring controller channel groups, channel-associated signaling (CAS) voice groups, or time-division multiplexing (TDM) cross-connects, see the Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide. Verifying and Saving Your Configuration To verify the configuration and save it in NVRAM so that the configuration remains in effect if the Cisco IAD is restarted, enter the following commands: Ste

  • Cisco IAD2435-8FXS, Americas Headquarters Cisco Systems, Inc. San Jose, CA Asia Pacific Headquarters Cisco Systems (USA) Pte. Ltd. Singapore Europe Headquarters Cisco Systems International BV Amsterdam, The Netherlands Cisco has more than 200 offices worldwide. Addresses, phone numbers, and fax numbers are listed on the Cisco Website at www.cisco.com/go/offices. Printed in the USA on recycled paper containing 10% postconsumer waste. 78-15666-02 B0

  • Cisco IAD2435-8FXS, 21 Figure 19 LAN, Administrative Access, and Power Connections (Cisco IAD2430 Series IADs) Figure 20 LAN, Administrative Access, and Power Connections (Cisco IAD2435 IAD) 1 Fast Ethernet port 2 Console port 3 AUX port 4 Fast Ethernet (straight-through) 5 RJ-45-to-DB9 console cable 6 RJ-45-to-DB25 auxiliary cable 1 Fast Ethernet port 2 Serial port—console or auxiliary 3 Fast Ethernet (straight-through) 4 RJ-45-to-DB9 console cable 88845 4 5 6 Ethernet hub 1 2 3 Cisco IAD2430 series Modem PC 232070 IAD2435-8FXS 12V DC SA CONSOLE AU X FastEthernet WAN 0 /1 0 /0 T1/E 1 FXS 1 Ethernet hub PC 3 4 2

  • Cisco IAD2435-8FXS, 27 Figure 28 Cisco IAD2430 Series LEDs (Cisco 2432-24FXS shown) Figure 29 Cisco IAD2435 Series LEDs No. LED/Color and Description 1 ACT—green: Green indicates activity—when any of the 24 voice ports is active in a call (off hook) or when one of the analog ports is in use Status—green: Green when accessing IAD 2 CF (Slot 0)—green: Green when accessing read or write function 3 LINK—green: Indicates link activity 100—green: 100BASE-T is active FDX—green: Green when full duplex is active, off when in half-dupl

  • Cisco IAD2435-8FXS, 14 Wall-Mounting the Cisco IAD2430, Cisco IAD2431, and Cisco IAD2432 IADs To wall-mount a Cisco IAD2430, Cisco IAD2431, or Cisco IAD2432 IAD, follow these steps: Step 1 Attach the short side of one bracket to the chassis, as shown in Figure 12, using two 6-32 x 1/4 slotted hex screws (provided). Be sure to use a plastic washer (provided) with each screw; the narrow end of the washer must fit into the bracket slot, facing the chassis. Caution Be sure to use the correct screws and plastic washers for this mounting option. (See Table 1 on page 11.) Figure 12 Attaching the Brackets for Wall-

  • Cisco IAD2435-8FXS, 6 Figure 5 Back Panel Function Options (Cisco IAD2435-8FXS IAD shown) Items Included with Cisco IAD2430, Cisco IAD2431, and Cisco IAD2432 IADs The following items are included with each Cisco IAD2430, Cisco IAD2431, and Cisco IAD2432 IAD: • Rack-mount brackets for 19-inch rack; grounding lug and fasteners; power cord • NEBS grounding kit (Cisco IAD2432-24FXS) • Connected RJ-45-to-DB9 cable (labeled Console) • Connected RJ-45-to-DB-25 cable (labeled Auxiliary) Note The rack-mount brackets for a 19-inch rack, the NEBS grounding kit, and the chassis guard for wall-mounting applications are not included with the Cisco IAD2435-8FXS IAD. Note Power cor

  • 23 To enable soft-offhook command on the port, and to access the connection command with plar opx syntax, see the Cisco Command Lookup Tool. Connecting the RJ-21 Cable in the Velcro Harness For the Cisco IAD2430 series models that have a Velcro harness available for the RJ-21 cable (see Figure 22), follow these steps: Figure 22 Cisco IAD2430 Series RJ-21 Velcro Harness Step 1 Slip

Related Products and Documents (Cables and connectors):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Olivetti 145D Operation & user’s manual olivetti/145d-833.pdf 02 Feb 2024 88
2 Dremel MOTO-TOOL 275 Manual  dremel/moto-tool-275-894.pdf 19 Oct 2023 2 0.07 Mb
3 ADC UTP Switchboard Cable Specification sheet adc/utp-switchboard-cable-P91.pdf 06 Jan 2023 4 0.15 Mb
4 Accel 75169 Installation instructions accel/75169-42U.pdf 09 Mar 2024 4
5 Frigidaire Panini Grill/Griddle Use & care manual frigidaire/panini-grill-griddle-271.pdf 23 Jun 2023 7
6 Philips MC230 Operation & user’s manual philips/mc230-97S.pdf 18 May 2023 20 0.91 Mb

Similar Resources:

  • Allen-Bradley

    1797-BIC

    (20 pages)
    FLEX Ex is a trademark of Rockwell Automation1 Publication 1797-5.13 - August 2001Installation InstructionsFLEX Ex Bus Isolator and Flexbus Connector(Cat. No. 1797-BIC, -CEC)Use the FLEX ExTM bus isolator to interconnect standard FLEX I/OTM modules to intrinsically safe FLEX Ex modules in the same I/O group.Component Identification1 Indicators2 Label3 M …
  • Eaton

    Crouse-Hinds GRUE Series

    (2 pages)
    APPLICATIONGRUE Series Outlet Boxes are installed in conduit and cable systems within hazardous areas to protect conductors in threaded rigid conduit, act as pull and splice boxes in conduit or cable systems, interconnect lengths of conduit, change direction of conduit and provide access to conductors for maintenance and future system changes.GRUE Series Out …
  • General Pump

    DHR50100D

    (2 pages)
    General Pump1174 Northland Drive • Mendota Heights, MN 55120Phone: 651.686.2199 • Fax: 800.535.1745www.generalpump.com • email: [email protected] 300631 Rev. J08-18WARNING!Exposure of skin directly topressurized air or fluids could result in severe bodily injury!1. Make sure incoming pressure does not exceed the rated pressure.2. Use …
  • Shure

    A33LK

    (2 pages)
    FeaturesUse the A33LK kit to connect a Shure FP24 to a ShureFP33 mixer. Combining an FP24 and a Shure FP33 (orFP32A) mixer yields a flexible, cost-effective, 5 X 2 field mix-ing setup with the following features:S Simultaneously accepts a stereo microphone, hard-wiredshotgun, and two RF lavalier microphones.S 48-volt phantom power for all five microphone inp …
  • Weh

    CLICKMATE TW154

    (68 pages)
    WEH® - We Engineer HightechCLICKMATE® TW154Operating instructions ⋅ Betriebsanleitung Quick connector for filling of breathing air bottlesSchnelladapter zum Füllen von Atemluftflaschen …
  • Holzmann

    EKR10M 230V

    (23 pages)
    Edition: 27.02.2019 – Revision - 00 – RaR - DE/EN Originalfassung DE BETRIEBSANLEITUNG ELEKTROKABELROLLER Übersetzung / Translation EN USER MANUAL ELECTRIC CABLE REEL EKR10M_230V …

Comments, Questions and Opinions: