Manualios.com

Cisco BTS 10200 Manual 

Cisco BTS 10200 Manual Online:

3.1, 1902 votes
Cisco BTS 10200 User Manual
Cisco BTS 10200 User Guide
Cisco BTS 10200 Online Manual

Text of Cisco BTS 10200 User Guide:

  • Cisco BTS 10200, 4-25 Cisco BTS 10200 Softswitch Dial Plan Guide, Release 4.5.x OL-8001-10 Chapter 4 Command Line Interface Routing Command Line Interface Routing Examples Carrier Use Dial-Plan “Y” The Carrier Use Dial-Plan “Y” CLI example is used in the Carrier Based Routing routing example. Carrier Use Dial-Plan “Y” Example: CLI>show carrier id=8888 Reply : Success: Entry 1 of 1 returned. ID=8888 STATUS=INS INTER=Y INTRA=N INTL=N CASUAL=Y CUT_THRU=Y OP_SERVICES=Y SEND_CN=N SEND_CSP=N USE_DIAL_PLAN=Y DESCRIPTION=TEST NETWORK_TYPE=NOTU

  • Cisco BTS 10200, 1-48 Cisco BTS 10200 Softswitch Dial Plan Guide, Release 4.5.x OL-8001-10 Chapter 1 Digit Translations Automatic Number Identification/Dialed Number Identification Service Manipulation MIN_DIGITS Description: Minimum number of digits required for a call. SMALLINT: 1-64 (Default = 10). Valid for Command: add, audit, change, show, sync Mandatory: add Default Value: 10 Possible Value: [1_64] Parser: DecimalParser NOA Description: Primary key. Nature of address. Use the Variable Default table to change the default value if required. Use noa=unknown

  • Cisco BTS 10200, 1-92 Cisco BTS 10200 Softswitch Dial Plan Guide, Release 4.5.x OL-8001-10 Chapter 1 Digit Translations Automatic Number Identification/Dialed Number Identification Service Manipulation TRAFFIC_TYPE Description: Specifies the type of traffic carried over this trunk group. It is required for incoming and bothway trunk groups. If it is not specified, the Call Agent defaults to local. VARCHAR(8): 1-8 ASCII characters. Permitted values are: LOCAL (Default)—Local incoming trunk group. PBX—Not used. Incoming PBX trunk group (for ISDN and CAS), DAL, and so forth. TANDEM—Incomi

  • 1-39 Cisco BTS 10200 Softswitch Dial Plan Guide, Release 4.5.x OL-8001-10 Chapter 1 Digit Translations Automatic Number Identification/Dialed Number Identification Service Manipulation ID Description: Primary key. The NOA Route Profile id. VARCHAR(16): 1-16 ASCII characters. Valid for Command: add, change, delete, show, audit, sync Mandatory: add, change, delete Possib

  • Cisco BTS 10200, 1-98 Cisco BTS 10200 Softswitch Dial Plan Guide, Release 4.5.x OL-8001-10 Chapter 1 Digit Translations Automatic Number Identification/Dialed Number Identification Service Manipulation DISPLAY Description: Specifies what token information to display on the screen. Valid only for the show command. VARCHAR(1024): 1-1024 (Default = all tokens are displayed). Permitted values are any valid token that can be shown for this command. Multiple tokens can be entered by separating with a comma. Valid for Command: s

  • 6-10 Cisco BTS 10200 Softswitch Dial Plan Guide, Release 4.5.x OL-8001-10 Chapter 6 Provisioning Dial Plans Provisioning a Dial Plan with the Extensible Provisioning and Operations Manager The Cisco BTS 10200 Softswitch Component window opens showing a list of dial plans. If this is the first dial plan (or device of this type) that you are adding, the list is empty. Ste

  • Cisco BTS 10200, 1-81 Cisco BTS 10200 Softswitch Dial Plan Guide, Release 4.5.x OL-8001-10 Chapter 1 Digit Translations Automatic Number Identification/Dialed Number Identification Service Manipulation CAUSE_CODE_MAP_ ID Description: Foreign key: Cause Code Map table. The cause code map ID. VARCHAR(16): 1-16 ASCII characters. Valid for Command: add, change, audit, sync, show Possible Value: [1_16] Parser: TextParser CLLI Description: Common Language Location Identifier for the remote switch. CHAR(11): Eleven ASCII characters. Valid for Command: add, audit, change, show Possible Valu

  • Cisco BTS 10200, 6-9 Cisco BTS 10200 Softswitch Dial Plan Guide, Release 4.5.x OL-8001-10 Chapter 6 Provisioning Dial Plans Provisioning a Dial Plan with the Extensible Provisioning and Operations Manager Provisioning a Dial Plan with the Extensible Provisioning and Operations Manager This section provides the detailed instructions for adding a dial plan to the Cisco BTS 10200 Softswitch configuration using the Extensible Provisioning and Operations Manager (EPOM). Additionally, detailed instructions are provided for using EPOM to manage configured dial plans. The EPOM also allows you to perform add, delete, and edit commands on

  • Cisco BTS 10200, 2-47 Cisco BTS 10200 Softswitch Dial Plan Guide, Release 4.5.x OL-8001-10 Chapter 2 Routing Policy Based Flexible Routing DOY8_POLICY_TYPE Description: See DOY1-POLICY-TYPE. VARCHAR(7): 1-7 ASCII characters. Valid for Command: add, change, audit, sync, show Possible Value: ODR, TOD, PERCENT, PREFIX, OLI, POP, ROUTE, NXX, REGION Parser: TextParser DOY9 Description: Month and day (day of year provisioning). CHAR(5): 5 characters in the format mm-dd. Valid for Command: add, change, audit, sync, show

  • 2-83 Cisco BTS 10200 Softswitch Dial Plan Guide, Release 4.5.x OL-8001-10 Chapter 2 Routing Policy Based Flexible Routing Policy Prefix The Policy Prefix enables the flexible routing of calls via the Cisco BTS 10200 Softswitch based on prefix (type of call). Typical call types include 1+ dialing, international calls, toll-free, and so on. The Policy Prefix is used mainly

  • Cisco BTS 10200, 3-20 Cisco BTS 10200 Softswitch Dial Plan Guide, Release 4.5.x OL-8001-10 Chapter 3 Dial Plans and Routing Local Toll-Free Service Provisioning Trunk Group Feature Data The Trunk Group Feature Data (trunk-grp-feature-data) table performs COS screening for Tandem calls. If the received ANI is not found in the ANI table, and the casual-call flag is set to Y, the call is allowed. If the casual-call flag is set to N, the call is blocked. The cos-restrict-id performs the COS screening. Trunk Group Service Profile The Trunk Group Service Profile (trunk-grp-service-profile) table links a trunk group to services. Local Toll-Free

  • Cisco BTS 10200, 2-73 Cisco BTS 10200 Softswitch Dial Plan Guide, Release 4.5.x OL-8001-10 Chapter 2 Routing Policy Based Flexible Routing DEFAULT_POLICY_ TYPE Description: Points to the default policy type to use if the next route is not found in the Policy table. Policy routing continues until policy-type=route or policy-nxx is reached. All policy types except Route point to the Policy Type table where type = ctype| odr | tod | percent | prefix | oli | pop | nxx. If policy-type = route, the Route t

  • Cisco BTS 10200, 3-23 Cisco BTS 10200 Softswitch Dial Plan Guide, Release 4.5.x OL-8001-10 Chapter 3 Dial Plans and Routing Carrier Based Routing Circuit Code The Circuit Code (circuit-code) table defines the circuit code value for the transit network selection (TNS) parameter. The circuit code value is defined based on the line, class of service, and call type. Special circuit code values are assigned to calls from coin or hotel motel lines. If special circuit code values are not required, the default circuit code values are based on the call ty

  • Cisco BTS 10200, 2-53 Cisco BTS 10200 Softswitch Dial Plan Guide, Release 4.5.x OL-8001-10 Chapter 2 Routing Policy Based Flexible Routing START_DOW4 Description: See START-DOW1. Valid for Command: add, change, audit, sync, show Possible Value: SUN, MON, TUE, WED, THU, FRI, SAT Parser: TextParser START_DOW5 Description: See START-DOW1. Valid for Command: add, change, audit, sync, show Possible Value: SUN, MON, TUE, WED, THU, FRI, SAT Parser: TextParser START_DOW6 Description: See START-DOW1. Valid for Command: add, change, audit, sync, show Possible Value: SUN, MON, TUE, WED, THU, FRI, SAT Parser: TextParser START_DOW7 Description: See START-DOW1. Valid for Comman

  • Cisco BTS 10200, 1-58 Cisco BTS 10200 Softswitch Dial Plan Guide, Release 4.5.x OL-8001-10 Chapter 1 Digit Translations Automatic Number Identification/Dialed Number Identification Service Manipulation CLDPTY_CTRL_ REL_ALWD Description: Called party release control allowed indication. Indicates to the Cisco BTS 10200 Softswitch that this call requires called party control. CHAR(1): Y/N (Default = N). Valid for Command: add, change, audit, sync, show Default Value: N Possible Value: Y, N Parser: BooleanParser DESCRIPTION Description: Service provider-defined description. VARCHAR(64): 1-64 ASCII characters. Valid for Command: add, change, audit, sync, show Possible Value: [

  • Cisco BTS 10200, 4-40 Cisco BTS 10200 Softswitch Dial Plan Guide, Release 4.5.x OL-8001-10 Chapter 4 Command Line Interface Routing Command Line Interface Routing Examples Subsciber and Sub-Profile The Subsciber and Sub-Profile CLI example is used in the Basic Subscriber Routingthe following and 1+ Interlata Call routing examples. Subsciber and Sub-Profile Example: CLI>show subscriber id=test1 Reply : Success: Entry 1 of 1 returned. ID=test1 CATEGORY=INDIVIDUAL NAME=c2421-227-2-1 STATUS=ACTIVE BILLING_DN=2124540001 DN1=2124540001 PRIVACY=NONE RING_TYPE_DN1=1 TERM_ID=aaln/S1/1 MGW_ID=c2421-227-2 PIC1=NONE PIC2=NONE PIC3=NONE GRP=N USAGE_SENS=Y SUB_PROFILE_ID=sp50 TERM_TYPE=TERM I

  • Cisco BTS 10200, 1-7 Cisco BTS 10200 Softswitch Dial Plan Guide, Release 4.5.x OL-8001-10 Chapter 1 Digit Translations Digit Manipulation Dot (.) Character The dot (.) character is used to indicate string position at which match operation is to be performed. If a dot character is specified as the first character of the match-string, the digits specified by each dot character are skipped until a question mark or any digit is encountered. The dot character can also be used to check the length of the input string (see examples below). Examples: Example 1: match-string="...555&q

  • Cisco BTS 10200, 4-23 Cisco BTS 10200 Softswitch Dial Plan Guide, Release 4.5.x OL-8001-10 Chapter 4 Command Line Interface Routing Command Line Interface Routing Examples Carrier All = N The Carrier All = N CLI example is used in the Carrier Based Routing routing examples. Carrier All = N Example: CLI>show carrier id=7777 Reply : Success: Entry 1 of 1 returned. ID=7777 STATUS=INS INTER=N INTRA=N INTL=N CASUAL=N CUT_THRU=N OP_SERVICES=N SEND_CN=N SEND_CSP=N USE_DIAL_PLAN=N ROUTE_GUIDE_ID=test NETWORK_TYPE=NOTUSED NATIONAL_NETWORK_PLAN=

  • Cisco BTS 10200, 2-94 Cisco BTS 10200 Softswitch Dial Plan Guide, Release 4.5.x OL-8001-10 Chapter 2 Routing Policy Based Flexible Routing Examples show region-profile id=e911; digit-string=210-470; add region-profile id=e911; digit-string=210-470; region=sanantonio; change region-profile id=e911; digit-string=210-470; region=sanantonio; delete region-profile id=e911; digit-string=210-470; Usage Guidelines Primary Key Token(s): ID, DIGIT_STRING Note This table allows the service provider to provision a list

  • CHAPTER 2-1 Cisco BTS 10200 Softswitch Dial Plan Guide, Release 4.5.x OL-8001-10 2 Routing Revised: December 9, 2008, OL-8001-10 Introduction This chapter provides a basic understanding of the Cisco BTS 10200 Softswitch routing types and an explanation of all routing types and explanation of how they function. Additionally examples of the routing types are pro

  • Cisco BTS 10200, CHAPTER 6-1 Cisco BTS 10200 Softswitch Dial Plan Guide, Release 4.5.x OL-8001-10 6 Provisioning Dial Plans Revised: December 9, 2008, OL-8001-10 Introduction This chapter provides detailed instructions for configuring Cisco BTS 10200 Softswitch configuration dial plans using the Command Line Interface (CLI) and the Cisco Extensible Provisioning and Operations Manager (EPOM). The following subjects are discussed: • Provisioning a Dial Plan with the Command Line Interface • Provisioning a Dial Plan with the Extensible Provisioning and Operations Manager Provisioning a Dial Plan with the Command Line Interface This section provides the detailed instructions for managing

  • Cisco BTS 10200, 1-54 Cisco BTS 10200 Softswitch Dial Plan Guide, Release 4.5.x OL-8001-10 Chapter 1 Digit Translations Automatic Number Identification/Dialed Number Identification Service Manipulation Variable Digit Dialing Variable digit dialing is used in the Europe where the length of the dialed number can vary from seven digits to ten digits, mainly in Germany. For a given NDC or EC the DN can vary from the minimum to the maximum specified in the Exchange Code table. Example: ndc=349, ec=234; min-digits=7; max-digits=10; (from the Exchange Code table) DN=3492340 could be a DN DN=3492341234 could also

  • Cisco BTS 10200, Glossary GL-3 Cisco BTS 10200 Softswitch Dial Plan Guide, Release 4.5.x OL-8001-10 D DA directory assistance DBM database management DDD direct distance or domestic dialing DEL delete DEST destination DIGMAN digital manipulation DN directory number DNIS dialed number identification service DOW day of week DOY day of year DP dial plan DP-ID dial-plan identification DPC destination point code DSC descending order DT CAS DTMF endpoints DTMF dual tone multifrequency E EMEA Europe, Middle East, and Asia EMG emergency EMS Element Management System ENU

  • 2-76 Cisco BTS 10200 Softswitch Dial Plan Guide, Release 4.5.x OL-8001-10 Chapter 2 Routing Policy Based Flexible Routing POLICY_ID3 Description: See policy-id1. VARCHAR(16): 1-16 ASCII characters. Valid for Command: add, change, audit, sync, show Possible Value: [1_16] Parser: TextParser POLICY_ID4 Description: See policy-id1. VARCHAR(16): 1-16 ASCII characters. Valid for

Related Products and Documents (Switch):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Asko W6863 Instrucciones de operación asko/w6863-5O5.pdf 22 Jun 2022 40 3.92 Mb
2 Whirlpool LA5705xT Use & care manual whirlpool/la5705xt-ZOU.pdf 27 Jul 2023 16 0.69 Mb
3 Eminent EM7080 Operation & user’s manual eminent/em7080-WOS.pdf 02 Jan 2024 24 0.79 Mb
4 Vertical Xcelerator IP IP2007 Operation & user’s manual vertical/xcelerator-ip-ip2007-O37.pdf 03 Jul 2023 64 1.29 Mb
5 Sony GDM-400PST9 Operating instructions manual sony/gdm-400pst9-291.pdf 02 Jan 2023 104 1.64 Mb
6 Garmin 705 Quick start manual garmin/705-P11.pdf 09 Jul 2023 8 0.67 Mb

Similar Resources:

  • Siemens

    SCALANCE X-300

    (84 pages)
    SIMATIC NETIndustrial Ethernet SwitchesSCALANCE X-300Compact Operating Instructions11/2019A5E00982643-18Introduction1Safety instructions2Recommendations on network security3Device description4Assembling5Connecting6Technical data7Dimension drawings8Certifications and approvals9 …
  • Edge-Core

    AS5916-54XKS

    (18 pages)
    1. Unpack the Switch and Check ContentsAS5916-54XKSAS5916-54XLRack Mounting Kit—2 front-post brackets, 2 rear-post brackets, 20 screws, and 2 ear-locking screwsGrounding kit—One grounding lug, 2 M5 screws and 2 washers (for AC model) Grounding kit—One grounding lug, 4 ring lugs, 2 M5 screws and 2 washers (for DC model) Power Cord Console Cable—RJ-4 …
  • Panasonic

    CF-VEBU Series

    (16 pages)
    1®I/O BoxI/OボックスボックスボックスボックスボックスCF-VEBU03UこのたびはI/Oボックスをお買い上げいただき、まことにありがとうございました。・この取扱説明書と保証書をよくお読みのうえ、正しくお使いください。そのあと保存し、必要なときにお読みください。� …
  • Extron electronics

    DTP T USW 233

    (4 pages)
    1 DTP T USW 233 • Setup GuideThis guide provides instructions for an experienced installer to set up and operate the Extron DTP T USW 233 switching video transmitter. The DTP T USW 233 transmitter switches among an analog video and two digital (HDMI) video inputs and, paired with a compatible receiver, can extend the selected signal up to 230 feet (70 m). …
  • Atlona

    AT-UHD-CLSO-612ED

    (37 pages)
    atlona.comToll free: 1-877-536-3976Local: 1-408-962-0515Atlona 6 Input Switcher and Scaler with HDBaseT and Mirrored HDMI OutputPlease check http://www.atlona.com/product/AT-UHD-CLSO-612ED for the most recent firmware update or manual.User ManualAT-UHD-CLSO-612ED …
  • LEGRAND

    adorne ASWR155RM

    (3 pages)
    adorne™ Whisper Switch, Wireless Master Commutateur de Whisper, Maître sans fil Interruptor de Whisper, Maestro Wireless Catalog Number(s) • Numéro(s) de Catalogue • Les Numéros de Catalogue: Country of Origin: Made in China • Pays ďorigine: Fabriqué en Chine • Pais de origen: Hecho en China Installation Instructions • Notice ďInstallati …

Comments, Questions and Opinions: