Cisco ATA-186 Administrator's Manual
|
CHAPTER 8-1 Cisco ATA 186 and Cisco ATA 188 Analog Telephone Adaptor Administrator’s Guide (H.323) OL-4008-01 8 Upgrading the Cisco ATA Signaling Image This section describes two methods for upgrading the Cisco ATA software for the H.323 protocol: • Upgrading the Signaling Image from a TFTP Server, page 8-1—This is the Cisco-recommended method for the H.323 protocol.
Cisco ATA-186, A-4 Cisco ATA 186 and Cisco ATA 188 Analog Telephone Adaptor Administrator’s Guide H.323 OL-4008-01 Appendix A Using H.323 Supplementary Services Common Supplementary Services About Calling Line Identification Restriction Calling Line Identification Restriction (CLIR) hides your identity from callers with Caller ID. Calling Line Identification Restriction in the United States Press *67 on your telephone keypad to activate CLIR. This feature is disabled when you hang up. Calling Line Identification Restriction in Sweden Press *31# on your telephone keypad to activate CL
Cisco ATA-186, 5-18 Cisco ATA 186 and Cisco ATA 188 Analog Telephone Adaptor Administrator’s Guide (H.323) OL-4008-01 Chapter 5 Parameters and Defaults H.323 Mode Parameter H.323 Mode Parameter This section describes the UseSIP parameter, which is used to set the Cisco ATA to H.323 mode if you are using the H.323 signaling protocol. UseSIP Description 0—Use H.323 mode. 1—Use SIP mode. Value Type Boolean Range 0 or 1 Default 0 Voice Configuration Menu Access Code 38 Operating Parameters The parameters for configuring codecs, fax features and VLAN settings are included in th
Cisco ATA-186, 5-17 Cisco ATA 186 and Cisco ATA 188 Analog Telephone Adaptor Administrator’s Guide (H.323) OL-4008-01 Chapter 5 Parameters and Defaults Gatekeeper Parameters GkTimeToLive Description This parameter specifies the “time to live” value that is used when the Cisco ATA registers with the H.323 gatekeeper. The registration is valid until the configured time expires. Value Type Integer Default 0 Range 30 to 4294967295 seconds Voice Configuration Menu Access Code 250 GkId Description This paramet
Cisco ATA-186, 5-24 Cisco ATA 186 and Cisco ATA 188 Analog Telephone Adaptor Administrator’s Guide (H.323) OL-4008-01 Chapter 5 Parameters and Defaults Operating Parameters CallFeatures Description Disable/enable CallFeatures by setting each corresponding bit to 0 or 1. The lower 16 bits are for the Phone 1 port, and the upper 16 bits are for the Phone 2 port. Table 5-2 provides definitions of each bit. Note The subscribed features that can be permanently disabled by the user are CLIP_CLIR, call waiting and Fax mode. A
Cisco ATA-186, 5-28 Cisco ATA 186 and Cisco ATA 188 Analog Telephone Adaptor Administrator’s Guide (H.323) OL-4008-01 Chapter 5 Parameters and Defaults Operating Parameters Default 0x00000000 Voice Configuration Menu Access Code 304 ConnectMode Description This parameter is a 32-bit bitmap used to control the connection mode of the selected call signaling protocol. Table 5-4 on page 5-28 provides bit definitions for this parameter. Value Type Bitmap Default 0x00060400 Voice Configuration Menu Access Code 311 Table 5-4 ConnectMode Parameter Bit Definitions Bit Number Definition 0 0—Use slow-start procedure (for H.225/Q.931 and H.245). 1—Use fast-start procedure (for
Cisco ATA-186, D-27 Cisco ATA 186 and Cisco ATA 188 Analog Telephone Adaptor Administrator’s Guide (H.323) OL-4008-01 Appendix D H.323 Signaling H.323 Signaling Scenarios { capabilityTableEntryNumber 32768 capability nonStandard : { nonStandardIdentifier h221NonStandard : { t35CountryCode 181 t35Extension 66 manufacturerCode 32896 } data '01'H } }, { capabilityTableEntryNumber 15 capability receiveAndTransmitDataApplicationCapability : { application t120 :separateLANStack :NULL ma
Cisco ATA-186, CHAPTER 7-1 Cisco ATA 186 and Cisco ATA 188 Analog Telephone Adaptor Administrator’s Guide (H.323) OL-4008-01 7 Configuring and Debugging Fax Services The Cisco ATA provides two modes of fax services that are capable of internetworking with Cisco IOS gateways over IP networks. These modes are called fax pass-through mode and fax mode. With fax pass-through mode, the Cisco ATA encodes fax traffic within the G.711 voice codec and passes it through the Voice Over IP (VoIP) network as though the fax were a voice call. This mode uses the Cisco proprietary fax upspeed method. With fax mode, the Cisco ATA presents itself as a device capable of using only G.711 codecs; therefo
Cisco ATA-186, 3-8 Cisco ATA 186 and Cisco ATA 188 Analog Telephone Adaptor Administrator’s Guide (H.323) OL-4008-01 Chapter 3 Configuring the Cisco ATA for H.323 Configuring the Cisco ATA Using a TFTP Server Note Be sure to configure the UseSIP parameter to the value of 0 (its default) to enable the H.323 protocol. Creating Unique and Common Cisco ATA Configuration Files If you have many Cisco ATAs to configure, a good approach is to create two configuration files: • One file that will contain only parameter values unique to a specific Cisco ATA. • One file for parameters that will be configured with values common to a group of C
Cisco ATA-186, Index IN-6 Cisco ATA 186 and Cisco ATA 188 Analog Telephone Adaptor Administrator’s Guide (H.323) OL-4008-01 R RADIUS server 4-5 receiving-audio codec 5-21 refreshing the Cisco ATA 3-20 refresh interval 4-9 refresh-interval configuration 4-9 registration 5-17 registration level-security 4-5 registration-level security 5-14 registration mode with an H.323 Gatekeeper 4-3 reorder delay 5-32 Reorder Tone 5-44 reorder tone 5-44 request device hostname from the DHCP server configuration 5-34 required parameters 4-1 reset Cisco ATA configuration 5-3 r
Cisco ATA-186, 5-44 Cisco ATA 186 and Cisco ATA 188 Analog Telephone Adaptor Administrator’s Guide (H.323) OL-4008-01 Chapter 5 Parameters and Defaults Optional Feature Parameters BusyTone Description The Cisco ATA plays the busy tone when the callee is busy. Default values for the nine-integer array • ntone—2 • freq0—30467 • freq1—28959 • level0—1191 • level1—1513 • steady—0 • on-time—4000 • off-time—4000 • total time to play tone—0 Voice Configuration Menu Access Code 921 ReorderTone Description The Cisco ATA plays the reorder tone (also know
6-11 Cisco ATA 186 and Cisco ATA 188 Analog Telephone Adaptor Administrator’s Guide H.323 OL-4008-01 Chapter 6 Call Commands Call Command Behavior CALLING_HOLDING: Cisco ATA is waiting for a second far end to respond while placing a connected call on hold • R—Cancel the call and revert to PREDIAL_HOLDING state. • ONH—Cancel the call and transfer the waiting part
Cisco ATA-186, C-4 Cisco ATA 186 and Cisco ATA 188 Analog Telephone Adaptor Administrator’s Guide (H.323) OL-4008-01 Appendix C Cisco ATA Specifications Software Specifications Fax G.711 fax pass-through and G.711 fax mode. Enhanced fax pass-through is supported on the Cisco ATA. Success of fax transmissions up to 14.4 kbps depends on network conditions, and fax modem/fax machine tolerance to those conditions. The network must have reasonably low network jitter, network delay, and packet-loss rate. Line-echo cancellation • Echo can
Cisco ATA-186, 4-8 Cisco ATA 186 and Cisco ATA 188 Analog Telephone Adaptor Administrator’s Guide (H.323) OL-4008-01 Chapter 4 Basic and Additional H.323 Services Additional H.323 Services • Configuring On-hook delay, page 4-10 • Configuring Reverse Audio Cut-Through Behavior, page 4-10 • Configuring Supplementary Service Behavior and Parameters, page 4-10 • Debugging Diagnostics, page 4-10 • Hardware Information Display, page 4-10 • Network Timing, page 4-11 • Polarity Settings, page 4-11 • Progress Tones, page 4-11 • Selecting DTMF and Hookflash Transmission Methods, page 4-11 �
Cisco ATA-186, 7-15 Cisco ATA 186 and Cisco ATA 188 Analog Telephone Adaptor Administrator’s Guide (H.323) OL-4008-01 Chapter 7 Configuring and Debugging Fax Services Debugging the Cisco ATA 186/188 Fax Services • ------------ Summary -------------- Input file: faxpassthru.cap <00.723>: (G723) 2.213:10000 => 2.116:10002 total 38 pkts(70 frames), lost 0 pkts, fill 7 silence pkts This indicates that the input filename is faxpassthru.cap. The output file 00.723 contains the G.723-compressed stream from <2.123:10
Cisco ATA-186, 3-13 Cisco ATA 186 and Cisco ATA 188 Analog Telephone Adaptor Administrator’s Guide (H.323) OL-4008-01 Chapter 3 Configuring the Cisco ATA for H.323 Configuring the Cisco ATA Using a TFTP Server Using a DHCP Server When using a DHCP server, configuration settings vary depending on whether or not the DHCP server is under the control of the Cisco ATA system administrator or the service provider. The simplest configuration is when the DHCP server is under the control of the Cisco ATA administrator, in which case the DHCP server provides the IP address of the TFTP serve
Cisco ATA-186, 2-2 Cisco ATA 186 and Cisco ATA 188 Analog Telephone Adaptor Administrator’s Guide (H.323) OL-4008-01 Chapter 2 Installing the Cisco ATA What the Cisco ATA Package Includes Warning The plug-socket combination must be accessible at all times because it serves as the main disconnecting device. Warning Do not work on the system or connect or disconnect cables during periods of lightning activity. For translated warnings, see the Regulatory Compliance and Safety Information for the Cisco ATA 186
Cisco ATA-186, Glossary GL-4 Cisco ATA 186 and Cisco ATA 188 Analog Telephone Adaptor Administrator’s Guide (H.323) OL-4008-01 IP Internet Protocol. Network layer protocol in the TCP/IP stack offering a connectionless internetwork service. IP provides features for addressing, type-of-service specification, fragmentation and reassembly, and security. Defined in RFC 791. IVR Interactive voice response. Term used to describe systems that provide information in the form of recorded messages over telephone lines in respons
5-30 Cisco ATA 186 and Cisco ATA 188 Analog Telephone Adaptor Administrator’s Guide (H.323) OL-4008-01 Chapter 5 Parameters and Defaults Operating Parameters Related Parameters • NTPIP, page 5-30 • AltNTPIP, page 5-30 NTPIP Description This parameter is the NTP IP address, required if DHCP server does not provide one. The Cisco ATA requires an NTP Server from which to obtain Coordi
Cisco ATA-186, 4-6 Cisco ATA 186 and Cisco ATA 188 Analog Telephone Adaptor Administrator’s Guide (H.323) OL-4008-01 Chapter 4 Basic and Additional H.323 Services Important Basic H.323 Services Using the Cisco ATA Without an H.323 Gatekeeper You can use the Cisco ATA without using an H.323 gatekeeper, as this section describes with the following topics: • Using the Cisco ATA With an H.323 Gateway but Without an H.323 Gatekeeper, page 4-6 • Using Multiple Cisco ATAs Without an H.323 Gatekeeper, page 4-6 Using the Cisco ATA With an H.32
Cisco ATA-186, 5-12 Cisco ATA 186 and Cisco ATA 188 Analog Telephone Adaptor Administrator’s Guide (H.323) OL-4008-01 Chapter 5 Parameters and Defaults Account Information Parameters PWD1 Description This parameter is the password for the Phone 2 port. Value Type Alphanumeric string Range Maximum number of characters: 31 Default 0 Voice Configuration Menu Access Code 14 Related Parameters • UID0, page 5-10 • UID1, page 5-11 • PWD0, page 5-10 • UseLoginID, page 5-13 • LoginID0, page 5-13 • LoginID1, page 5-14 • AutMethod, page 5-14 Gateway Description Use this parameter to specify the H.323 gateway IP ad
Cisco ATA-186, D-7 Cisco ATA 186 and Cisco ATA 188 Analog Telephone Adaptor Administrator’s Guide (H.323) OL-4008-01 Appendix D H.323 Signaling H.323 Signaling Scenarios 18. H.245 Open Audio Logical Channel—Remote H.323 endpoint to local H.323 endpoint Before actual transmission or reception of voice, video, or data, notification that the primary logical channel for the remote H.323 endpoint has been opened, ensuring clear two-way communication. 19. H.245 Open Audio Logical Channel Acknowledgement—Local H.323 endpoint to remote H.323 endpoint Local H.323 endpoint acknowledges readiness. 20. Bi-Directional Audio with Transcoding in the Endpoints Two-way communication ensues between
Glossary GL-7 Cisco ATA 186 and Cisco ATA 188 Analog Telephone Adaptor Administrator’s Guide (H.323) OL-4008-01 voice packet gateway Gateway platforms that enable Internet telephony service providers to offer residential and business-class services for Internet telephony. VoIP Voice over IP. The capability to carry normal telephony-style voice over an IP-ba
Cisco ATA-186, Glossary GL-2 Cisco ATA 186 and Cisco ATA 188 Analog Telephone Adaptor Administrator’s Guide (H.323) OL-4008-01 compression The running of a data set through an algorithm that reduces the space required to store or the bandwidth required to transmit the data set. Compare with companding and expansion. CoS Class of service. An indication of how an upper-layer protocol requires a lower-layer protocol to treat its messages. In SNA subarea routing, CoS definitions are used by subarea nodes to determine the optimal route to establish a given session. A CoS definition comprises a virtual ro
6-4 Cisco ATA 186 and Cisco ATA 188 Analog Telephone Adaptor Administrator’s Guide H.323 OL-4008-01 Chapter 6 Call Commands Syntax Input Sequence Identifiers Action Identifiers Table 6-2 Input Sequence Identifiers Identifier Input Sequence 0-9,#* DTMF digits f hook flash ooff-hook @ anytime; for example, @f means anytime hook- flash occurs h on-hook S#|* N 0|1|2|3|4
Cisco 8961 Network Card Release notes
8961 |
Cisco DPC2425 Network Card Operation & user’s manual
DPC2425 |
Cisco 3545 MCU Network Card Installation and upgrade manual
3545 MCU |
Cisco DDR2200 Series Network Card Installation and operation manual
DDR2200 Series |
Cisco AS5300 - Universal Access Server Network Card Appendix
AS5300 - Universal Access Server |
Cisco SPA2102 Network Card Administration manual
SPA2102 |
Cisco 7970 Network Card Phone manual
7970 |
Cisco 7975G - Unified IP Phone VoIP Network Card Installation manual
7975G - Unified IP Phone VoIP |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | Mercury | 1999 Villager | Owner's manual | mercury/1999-villager-866.pdf | 20 Aug 2022 | 264 | |
2 | PURE | HIGHWAY | Owner's manual | pure/highway-P73.pdf | 07 Jan 2024 | 24 | |
3 | Oki | OKIPAGE8c | Quick start manual | oki/okipage8c-2VZ.pdf | 04 Nov 2022 | 40 | |
4 | Lexicon | 200 | Owner's manual | lexicon/200-5NC.pdf | 30 Mar 2023 | 70 | |
5 | Vortex | Vitalizer Plus | Operation & user’s manual | vortex/vitalizer-plus-634.pdf | 24 Dec 2023 | 8 | |
6 | Realistic | PRO-2005 | Owner's manual | realistic/pro-2005-GHF.pdf | 07 Oct 2022 | 34 | 0.62 Mb |
Telenetics
ΩOMEGACommunications Interface CabinetModel No. OM-AMPS-100(including Model No. OM-MP8-100 8-Port Module Option andModel No. OM-BAT-100 Battery Option)Installation, Operation, andMaintenance Manual0049−0706−000 B
…
OM-AMPS-100(70 pages) |
3Com
® Q UICK S TART FOR THE T OKEN L INK V ELOCITY ISA 3C319 N ETWORK I NTERFACE C ARD Part Number 09-0965-001/August 1997This Quick Start is for experienced token ring network users. Perform the following steps to install the 3Com ® TokenLink ® Velocity ™ network interface card (NIC) (3C319): 1 Install the 3C319 NIC in an ISA or EISA slot in …
3C319(2 pages) |
Multitech
FaxFinder® FF Model Series V.34 Fax Server Client Operation Primer Contents INTRODUCTION 3 SENDING A FAX 3 RECEIVING A FAX 10 Receiving Faxes from the Fax Attendant (Manual Routing Mode)....................................................................................10 Receiving Faxes Directly from the Admin (Automated Routing Mode).. …
FF100(14 pages) |
Linksys
This sheet will guide you through the basic steps needed to install the InstantGigabit Network Adapter onto your network. If you have any problems duringinstallation, refer to the Troubleshooting section of the User Guide.Model No.:EG1032EG1064 Instant Gigabit Network AdapterInstant Gigabit SeriesQuick Installationfor Windows 95Making Connectivity Easier™Q …
EG1032(1 pages) |
HP
HP recommends Windows Vista®Business 1.Volume mute button with LED indicator 14.Touchpad with scroll zone2.Volume scroll zone with up/down LED indicators15.Touchpad buttons, three3.Calculator button16.Hard drive / optical drive activity / HP 3D DriveGuard LED4.RJ-45/Ethernet port17.Battery charging LED5.RJ-11/modem port18.Power/standby LED6.Optical …
Compaq 8710p(42 pages) |
Transition Networks
NM2-FXS-2230-SFP-01 Install Guide 33730 Rev. B https://www.transition.com Page 1 of 14 NM2-FXS-2230-SFP-01 M.2 100-Base-FX Ethernet Fiber Network Interface Card Install Guide Ethernet Fiber NIC with 100-Base-FX SFP Supports PCI Express M.2 specification Installs in Dell OptiPlex™ 7040 and 7050 Micro PCs and Wyse 7000 Seri …
M2-FXS-2230-SFP-01(14 pages) |
Laney Speakers Audiohub Venue Series#F9E1DX: Audiohub Venue Series Speakers Operation & user’s manual Audiohub Venue Series, 37 |
NeuLog Kitchen Appliances NUL-207#QB8S49 NUL-207: NeuLog Kitchen Appliances Owner Documentation NUL-207, 4 |
AEG Refrigerator SANTO U 9 60 40-4 iAEG Refrigerator SANTO U 9 60 40-4 i Operating and installation instructions SANTO U 9 60 40-4 i, 32 |
Williams Sound Receiver MOD 112Williams Sound MOD 112 Guide (Doc Type: Receiver Installation manual and user's manual) MOD 112, 24 |
SilverStone Adapter ECM24Adapter Manual (SilverStone ECM24) ECM24, 2 |
Microdigital DVR MDR-AH SeriesMDR-AH Series (DVR ePDF Guide, #6A6EJY) MDR-AH Series, 112 |
Hurst Jaws Of Life Safety Equipment EDraulic EWXT SeriesSafety Equipment PDF Operating instructions manual EDraulic EWXT Series, 78 |
Panasonic Air Conditioner U-8ME2R8U-8ME2R8 Operating instructions manual - 6C7JI8 U-8ME2R8, 8 |
Topaz Systems Adapter A-ETH1-1Adapter How-to manual (Topaz Systems A-ETH1-1) A-ETH1-1, 6 |
New Wave Research Measuring Instruments TempestMeasuring Instruments Operator's manual (New Wave Research Tempest) Tempest, 72 |
Cobra Two-Way Radio PR270Owner's manual for Cobra PR270 Two-Way Radio PR270, 11 |
Kohler Toilets K4915PDF User Manual (@NR344L), Kohler K4915 Toilets (29th Oct 2023) K4915, 20 |