Cisco SLM224G4PS Operation & User’s Manual
|
Cisco SLM224G4PS, Chapter 5 Configuration Using the Web-based Utility 33 24/48-Port 10/100 + 4-Port Gigabit Smart Switch with Resilient Clustering Technology and PoE Broadcast Control Select the checkbox to apply Broadcast control on the selected interface. Broadcast control limits the amount of Broadcast packet types to be forwarded. The default is not selected (disabled). Mode Specifies the Broadcast mode currently enabled on the device. The possible values are: Multicast & Broadcast Counts Broadcast and Multicast traffic together. Broadcast Only Counts only Broadcast traffic. Rate Threshold The maximum rate (packets per second) at which
Cisco SLM224G4PS, Chapter 5 Configuration Using the Web-based Utility 21 24/48-Port 10/100 + 4-Port Gigabit Smart Switch with Resilient Clustering Technology and PoE Speed The port’s configured rate in Mbps. Duplex The port’s current duplex mode, Half or Full. MDI/MDIX The port’s MDI/MDIX type. The MDI setting is used if the port is connected to an end station. The MDIX setting is used if the port is connected to a hub or another switch. Flow Control This is the flow control status of the port. It is active when the port uses Full Duplex Mode. Type Displays the port type. LAG This indicates if the port belongs to a LAG. Port Configura
Cisco SLM224G4PS, ii About This Guide 24/48-Port 10/100 + 4-Port Gigabit Smart Switch with Resilient Clustering Technology and PoE About This Guide Icon Descriptions While reading through the User Guide you may see various icons that call attention to specific items. Below is a description of these icons: NOTE: This check mark indicates that there is a note of interest and is something that you should pay special attention to while using the product. WARNING: This exclamation point indicates that there is a caution or warning and it is something that could damage your property or product
Cisco SLM224G4PS, 53 About Switch Stacking 24/48-Port 10/100 + 4-Port Gigabit Smart Switch with Resilient Clustering Technology and PoE Appendix B Stack Units Startup Process Whenever a unit in stack mode is initialized (powered up or rebooted) it goes through the same exact process, consisting of the following three steps: Master Discovery/Election. Unit ID allocation by the Master (including duplicate Unit ID conflict resolution) Unit/port configuration by the Master Master Discovery Whenever a unit in stack mode initializes, its behavior will depend on its Unit ID (if any). If the unit does not have a current Unit ID (that is, the unit is in factory default mode). If there is a maste
Cisco SLM224G4PS, 59 Glossary 24/48-Port 10/100 + 4-Port Gigabit Smart Switch with Resilient Clustering Technology and PoE Appendix C Appendix C: Glossary This glossary contains some basic networking terms you may come across when using this product. WEB: For additional terms, please visit the glossary at www.linksys.com/glossary Access Mode Specifies the method by which user access is granted to the system. Access Point A device that allows wireless-equipped computers and other devices to communicate with a wired network. Also used to expand the range of a wireless
Cisco SLM224G4PS, Chapter 5 Configuration Using the Web-based Utility 34 24/48-Port 10/100 + 4-Port Gigabit Smart Switch with Resilient Clustering Technology and PoE The assignment of network traffic to a particular hardware queue The assignment of internal resources Traffic shaping The terms Class of Service (CoS) and QoS are used in the following context: CoS provides varying Layer 2 traffic services. CoS refers to classifying traffic into traffic classes, where each class is handled as an aggre
Cisco SLM224G4PS, Chapter 5 Configuration Using the Web-based Utility 19 24/48-Port 10/100 + 4-Port Gigabit Smart Switch with Resilient Clustering Technology and PoE System Location This is used to enter a description of where the Switch is physically located, such as 3rd Floor. System Contact Enter the name of the administrator responsible for the system. System Object ID This is used for SNMP purposes and is set to 1.3.6.1.4.1.3955.6.5.224(248).2. Base MAC Address Displays the Switch’s physical address . IP Configuration Management VLAN This drop-down menu allow
Cisco SLM224G4PS, 65 Appendix E Warranty Information 24/48-Port 10/100 + 4-Port Gigabit Smart Switch with Resilient Clustering Technology and PoE service offerings. This limited warranty shall not apply to such third party software or service offerings. This limited warranty does not guarantee any continued availability of a third party’s service for which this product’s use or operation may require. TO THE EXTENT NOT PROHIBITED BY LAW, ALL IMPLIED WARRANTIES AND CONDITIONS OF MERCHANTABILITY, SATISFACTORY QUALITY OR FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED TO THE DURATION OF THE WARRANTY PERIOD. ALL OTHER EXPRESS OR IM
52 About Switch Stacking 24/48-Port 10/100 + 4-Port Gigabit Smart Switch with Resilient Clustering Technology and PoE Appendix B the Console port, Telnet or Web-based Utility) and reset the units to make this assignment permanent. The unit that is assigned number 1 will act as the Master; this is indicated by the Stack Master LED on its front panel being lit amber. The unit that
Cisco SLM224G4PS, 51 About Switch Stacking 24/48-Port 10/100 + 4-Port Gigabit Smart Switch with Resilient Clustering Technology and PoE Appendix B Appendix B: About Switch Stacking A switch may operate in one of two modes: Stack or Standalone. You can select either mode during software boot or using the web-based utility’s Setup > Summary screen, with the new mode taking effect after the unit is reset. The factory default is Stack mode. Standalone Mode A switch operating in Standalone mode runs as an independent, single unit. All ports of a standalone s
Cisco SLM224G4PS, 14 Configuration Using the Console Interface 24/48-Port 10/100 + 4-Port Gigabit Smart Switch with Resilient Clustering Technology and PoE Chapter 4 After the traceroute test is complete, the TraceRoute screen displays the IP address, status, and statistics of the traceroute test. File Management The File Management screen allows you to upload or download files, such as the startup configuration, boot, or image file, using a TFTP server. File Management Source File Specify the location of the file to transfer. Select one of the following: TFTP If the file is located on a TFTP server. Image If the file is
Cisco SLM224G4PS, 9 Configuration Using the Console Interface 24/48-Port 10/100 + 4-Port Gigabit Smart Switch with Resilient Clustering Technology and PoE Chapter 4 Chapter 4: Configuration Using the Console Interface Overview The Switch features a menu-driven console interface that lets you perform basic switch configuration and easily manage your network. To use the console interface, you either run the HyperTerminal application to configure a serial connection through the Switch’s console port, or run a telnet session over an Ethernet connection. Using the HyperTerminal Application To access the console interface using HyperTermi
Cisco SLM224G4PS, 5 Installation 24/48-Port 10/100 + 4-Port Gigabit Smart Switch with Resilient Clustering Technology and PoE Chapter 3 Chapter 3: Installation Overview This chapter will explain how to connect network devices to the Switch. The following diagram shows a typical network configuration. Internet Cable/DSL Modem Router Wireless Access Point Server Uplink via Fiber to Switch 10/100/1000 Desktop 10/100 Notebook Typical Network Configuration for the SLM248G4PS When you connect your network devices, make sure you do not exceed the maximum cabling distances, which are listed in the following table: Maximum Cabling Distances From To Maximum Distance Switch
Cisco SLM224G4PS, Chapter 5 Configuration Using the Web-based Utility 39 24/48-Port 10/100 + 4-Port Gigabit Smart Switch with Resilient Clustering Technology and PoE Enable Bridge Multicast Filtering Select this option to TBD. The default is disabled. Interface, Gigabit, LAG Lists switch interfaces and LAGs that can be added to a Multicast service. The configuration options are as follows: Static Indicates the port is user-defined. Dynamic Indicates the port is configured dynamically. Forbidden Forbidden ports are not included
13 Configuration Using the Console Interface 24/48-Port 10/100 + 4-Port Gigabit Smart Switch with Resilient Clustering Technology and PoE Chapter 4 IP Address Settings The IP Address Settings screen allows you to set the IP information for the Switch. IP Address Configuration IP Address This sets the Switch’s IP Address. The default setting is
55 About Switch Stacking 24/48-Port 10/100 + 4-Port Gigabit Smart Switch with Resilient Clustering Technology and PoE Appendix B If the incoming unit did not have an assigned Unit ID (that is, it was in factory default mode), it will be assigned the lowest available Unit ID by the Master. It is strongly recommended that automatic assigned unit ID mode be used since it provides
Cisco SLM224G4PS, Chapter 5 Configuration Using the Web-based Utility 40 24/48-Port 10/100 + 4-Port Gigabit Smart Switch with Resilient Clustering Technology and PoE Use Default Uses the device generated Engine ID. The default Engine ID is based on the device MAC address and is defined per standard as: First 4 octets First bit = 1, the rest is IANA Enterprise number. Fifth octet Set to 3 to indicate the MAC address that follows. Last 6 octets MAC address of the device. SNMP Notifications Indicates if the device can send SNMP notifications. Authentication Notifications Indicates if SNMP Authentication failure notification is enable
Cisco SLM224G4PS, Chapter 5 Configuration Using the Web-based Utility 25 24/48-Port 10/100 + 4-Port Gigabit Smart Switch with Resilient Clustering Technology and PoE Ingress Filtering Enables or disables Ingress filtering on the port. Ingress filtering discards packets that do not match port ingress rules. The default is Enabled. LAG Displays the LAG, if any, to which the port belongs. A port’s LAG settings override the VLAN port settings. Click Save Changes to save your changes, or click Cancel Changes to cancel. VLAN Management > Port to VLAN You use the Port to VLAN screen to add ports to a VLAN and delete ports from a VLAN.
Cisco SLM224G4PS, 10 Configuration Using the Console Interface 24/48-Port 10/100 + 4-Port Gigabit Smart Switch with Resilient Clustering Technology and PoE Chapter 4 How to Use the Console Interface The Console Interface consists of a hierarchical series of menu screens and settings screens. Each menu displays a list of options. Selecting an option brings up a settings screen where you can configure the relevant settings. To select a menu option, either press the number of the option in the list (for example, press 5 to select Help from the Main Menu), or use the arrow keys to move up or down the list until the option is highlighted, then p
Cisco SLM224G4PS, Chapter 5 Configuration Using the Web-based Utility 28 24/48-Port 10/100 + 4-Port Gigabit Smart Switch with Resilient Clustering Technology and PoE Oversize Packets Displays the number of oversized packets (over 1518 octets) received on the interface since the device was last refreshed. Fragments Displays the number of fragments (packets with less than 64 octets, excluding framing bits, but including FCS octets) received on the interface since the device was last refreshed. Jabbers Displays the total number of received packets that were
Cisco SLM224G4PS, Chapter 5 Configuration Using the Web-based Utility 43 24/48-Port 10/100 + 4-Port Gigabit Smart Switch with Resilient Clustering Technology and PoE Notification Type Defines the notification sent. The possible field values are: Traps Indicates traps are sent. Informs Indicates informs are sent. SNMPv1,2 Enables SNMPv1,2 as the Notification Recipient. Either SNMPv1,2 or SNMPv3 can be enabled at any one time, but not both at the same time. If SNMPv1,2 is enabled, the Community String and Notification Version fields are enabled for configuration: Community String Identifies the community string of
Cisco SLM224G4PS, Chapter 5 Configuration Using the Web-based Utility 48 24/48-Port 10/100 + 4-Port Gigabit Smart Switch with Resilient Clustering Technology and PoE Admin > Logging Admin > Logging The System Logs allow you to view device events in real time, and recording the events for later usage. System Logs record and manage events and report errors or informational messages. Event messages have a unique format, as per the SYSLOG protocols recommended message format for all error reporting. For example, Syslog and local device reporting messages are assigned a severity cod
Cisco SLM224G4PS, 12 Configuration Using the Console Interface 24/48-Port 10/100 + 4-Port Gigabit Smart Switch with Resilient Clustering Technology and PoE Chapter 4 User & Password Settings The User & Password Settings screen displays all the user accounts defined on the system. User & Password Settings The default account is admin. You cannot edit this account (its user name and password cannot be changed). For security purposes, Linksys recommends creating at least one user account with a unique user name and passwo
4 Product Overview 24/48-Port 10/100 + 4-Port Gigabit Smart Switch with Resilient Clustering Technology and PoE Chapter 2 SLM224G4PS Shared Port Mapping miniGBIC Port Standard Port miniGBIC 1 G3 miniGBIC 2 G4 Back Panel The Console port and power port are located on the back panel of the Switch. Back Panel of the SLM224G4PS CONSOLE The Console port is a serial port t
Cisco 7304 Network Card Installation and configuration manual
7304 |
Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion Network Card Quick reference manual
6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion |
Cisco 3560 24PS - Catalyst SMI Switch Network Card Technical specifications
3560 24PS - Catalyst SMI Switch |
Cisco ME-C3750-24TE-M Network Card Hardware installation manual
ME-C3750-24TE-M |
Cisco WUSB600N Network Card Bedienungsanleitung
WUSB600N |
Cisco Cisco ASA 5500 Series Network Card Manual
Cisco ASA 5500 Series |
Cisco 4506-E - Catalyst Switch Network Card Overview
4506-E - Catalyst Switch |
Cisco CSS 11501 - Content Services Switch Network Card Datasheet
CSS 11501 - Content Services Switch |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | Lanta | Aurora Bar X44 | Owner's handbook manual | lanta/aurora-bar-x44-2VE.pdf | 11 Oct 2023 | 7 | |
2 | Hitachi | Innovate CP-RX78 | Operating manual | hitachi/innovate-cp-rx78-137.pdf | 05 Sep 2022 | 92 | 1.81 Mb |
3 | LG | LFX23961SW - 22.6 cu. ft. Refrigerator | Owner's manual | lg/lfx23961sw-22-6-cu-ft-refrigerator-T8E.pdf | 06 Dec 2023 | 34 | |
4 | Field Controls | 46257600 | Instructions manual | field-controls/46257600-78V.pdf | 02 Dec 2023 | 32 | 1.84 Mb |
5 | Philips | 650 | Operation & user’s manual | philips/650-U6D.pdf | 05 Jan 2024 | 16 | 0.75 Mb |
6 | Crestron | RoomView | Reference manual | crestron/roomview-45S.pdf | 16 Dec 2022 | 84 | 2.16 Mb |
Link electronics
LINK ELECTRONICS, INC.AUDIO TONE GENERATORMODEL 6160The 6160 is a high quality audio tone generator for theLink 3000 mounting frame. It features simultaneous1 kHz and 400Hz balanced, low impedance outputs.A third output is provided for 1 kHz or 400Hz,selectable from the front panel.The 6160 is design …
Audio Tone Generator 6160(2 pages) |
Panasonic
SHE00054BED This product complies with the RoHS Directive (EU 2002/95/EC).Publication date: October 20081PhototransistorsPNA1803LSilicon planar typeFor optical control systems Features Fast response Wide spectral sensitivity characteristics φ3 plastic packageAbsolute Maximum Ratings Ta = 25°CParameter Symbol Rating UnitCollector-emitter …
Phototransistors PNA1803L(3 pages) |
Murphy
SM Series TANKTENDTMSystems Installation and Operation Instructions Models: SM1, SM1VR, SM2, SM2VR, SM3, SM3VR, SM4, SM4VRTSM-95129NRevised 01-97Section 15(00-02-2019)The SM Series Systemcan monitor above or below ground,single or multi-tank systems (4 tanks maximum). The SM Seriesincludes BGT1 gage (s) in a wall mounting panel. The SMVR seriesincludes a va …
SM1(4 pages) |
Pentagram
ENInstallation and Operation ManualPENTAGRAM horNet Wi-Fi USB [P 6132-20]2010-10-04ENThe latest versions of manual, drivers and applications are available on www.pentagram.eu .
…
horNET Wi-Fi PCI(24 pages) |
Net to Net Technologies
220-0000070 rev01UIM-T1T1 Uplink Interface ModuleInstallation1. Unpack and inspect the equipment.The following components should be included: 1 UIM-T1 4 #6 Phillips Panhead Internal Locking Screws 2 #6 Phillips Beige Flathead ScrewsIf there is any visible damage, do not attempt to connect the device. Contact Customer Support at 1-8 …
UIM-T1(6 pages) |
StarTech.com
Manual Revision: 11/23/2015For the latest information, technical specications, and support for this product, please visit www.startech.com/ST1000SPEX43.FR: Guide de l’utilisateur - fr.startech.comDE: Bedienungsanleitung - de.startech.comES: Guía del usuario - es.startech.comNL: Gebruiksaanwijzing - nl.startech.comPT: Guia do usuário - pt.startech.comI …
ST1000SPEX43(9 pages) |
Monessen Hearth Indoor Fireplace Peninsula 624WBPFIndoor Fireplace Product specifications (Monessen Hearth Peninsula 624WBPF) Peninsula 624WBPF, 1 |
Beechcraft Toy BonanzaToy PDF Manual Bonanza, 37 |
EUROSTYLE DVR JS400EUROSTYLE JS400 DVR Quick user manual JS400, 4 |
Epson Home Theater System PowerLite Home Cinema 3020Home Theater System #P21Y16 PowerLite Home Cinema 3020, 96 |
Bionaire Heater BOF1500Bionaire Heater Instruction manual (File: bionaire-bof1500-instruction-manual-10, 20.11.2023) BOF1500, 10 |
Gaggenau Wine Cooler RW464760RW4.4Wine Cooler PDF Operating instructions manual RW464760RW4.4, 101 |
Toshiba Laptop P505-S8970Toshiba P505-S8970 Manual (Operation & user’s manual), @87H468 P505-S8970, 253 |
Sony TV Bravia XBR-65HX950Sony Product Manual: Bravia XBR-65HX950 PDF Specifications - 4Q8U97 Bravia XBR-65HX950, 4 |
HP Desktop Firebird 802Desktop Specifications (HP Firebird 802) Firebird 802, 2 |
Panasonic Vacuum Cleaner MC-V5391CVacuum Cleaner #362979 MC-V5391C, 12 |
Porsche Automobile 911 GT3 R 2012911 GT3 R 2012 Technical manual - T5L362 911 GT3 R 2012, 153 |