Manualios.com

Cisco SRW208 - Small Business Managed Switch Operation & User’s Manual

  • SRW208 - Small Business Managed Switch Switch
  • maEUGjL1DCK3g
  • Operation & User’s Manual
  • PDF / Adobe Acrobat Reader
  • 86

Cisco SRW208 - Small Business Managed Switch Manual Online:

3.95, 2133 votes
Cisco SRW208 - Small Business Managed Switch User Manual
Cisco SRW208 - Small Business Managed Switch User Guide
Cisco SRW208 - Small Business Managed Switch Online Manual

Text of Cisco SRW208 - Small Business Managed Switch User Guide:

  • Cisco SRW208 - Small Business Managed Switch, Chapter 5 Advanced Configuration 48 8-Port 10/100 Ethernet Switch with Webview SNMP > Global Parameters Local Engine ID Indicates the local device engine ID. The field value is a hexadecimal string. Each byte in hexadecimal character strings consists of two hexadecimal digits. Each byte can be separated by a period or a colon. The Engine ID must be defined before SNMPv3 is enabled. For stand- alone devices, select a default Engine ID that is comprised of Enterprise number and the default MAC address. For a stackable system configure the Engine ID, and verify that the Engine ID is unique for the administrative domain.

  • 67 Specifications 8-Port 10/100 Ethernet Switch with Webview Appendix D (History, Statistics, Alarms, and Events) for Enhanced Trac Management, Monitoring, and Analysis. Firmware Upgrade Web Browser Upgrade (HTTP) TFTP Upgrade Port Mirroring Trac on a Port can be Mirrored to another Port for Analysis with a Network Analyzer or RMON Probe Other Man

  • Chapter 5 Advanced Configuration 41 8-Port 10/100 Ethernet Switch with Webview Aggregate Policer Settings The Aggregate Policer button opens the New Aggregate Policer screen. New Aggregate Policer Advanced Mode > New Aggregate Policer Aggregate Policer Name Enter a name in this field. Ingress Committed Information Rate (CIR) Defines the CIR in bits per second. This field is only re

  • Chapter 5 Advanced Configuration 40 8-Port 10/100 Ethernet Switch with Webview Out of Profile DSCP Advanced Mode > Out of Profile DSCP DSCP In Displays the DSCP In value. DSCP Out Displays the current DSCP out value. A new value can be selected from the pull-down menu. The Policy Settings button opens the Policy Name screen. Policy Name Advan

  • Cisco SRW208 - Small Business Managed Switch, Chapter 5 Advanced Configuration 53 8-Port 10/100 Ethernet Switch with Webview Delete on Reset • The MAC address is deleted when the device is reset. Delete on Timeout • The MAC address is deleted when a timeout occurs. Secure • The MAC Address is defined for locked ports. Query Port Specifies the interface for which the table is queried. There are two interface types from which to select. Port • The specific port number. LAG • The specific LAG number. MAC Address Specifies the MAC address for which the table is queried. V

  • Cisco SRW208 - Small Business Managed Switch, 63 Glossary 8-Port 10/100 Ethernet Switch with Webview Appendix C MAC (Media Access Control) Address The unique address that a manufacturer assigns to each networking device. Mask A filter that includes or excludes certain values, for example parts of an IP address. Mbps (MegaBits Per Second) One million bits per second; a unit of measurement for data transmission. MD5 (Message Digest 5) An algorithm that produces a 128-bit hash. MD5 is a variation of MD4, and increases MD4 security. MD5 verifies the integrity of the communication and authenticates the origin of the communication.

  • Chapter 5 Advanced Configuration 47 8-Port 10/100 Ethernet Switch with Webview Leave Timeout Indicates the amount of time the host waits, after requesting to leave the IGMP group and not receiving a Join message from another station, before timing out. If a Leave Timeout occurs, the switch notifies the Multicast device to stop sending tr

  • Cisco SRW208 - Small Business Managed Switch, 61 Glossary 8-Port 10/100 Ethernet Switch with Webview Appendix C Appendix C: Glossary This glossary contains some basic networking terms you may come across when using this product. WEB: For additional terms, please visit the glossary at www.linksys.com/glossary Access Mode Specifies the method by which user access is granted to the system. Access Point A device that allows wireless-equipped computers and other devices to communicate with a wired network. Also used to expand the range of

  • 16 Configuration Using the Console Interface 8-Port 10/100 Ethernet Switch with Webview Chapter 4 File Management The File Management screen allows you to upload or download files, such as the startup configuration, boot, or image file, using a TFTP server. Select Edit to change the settings. When your changes are complete, press the Esc key to r

  • Cisco SRW208 - Small Business Managed Switch, Chapter 5 Advanced Configuration 38 8-Port 10/100 Ethernet Switch with Webview Basic • Enables QoS on the interface. Advanced • Enables Advanced mode QoS on the interface. Class of Service Specifies the CoS priority tag values, where zero is the lowest and 7 is the highest. Queue Defines the traffic forwarding queue to which the CoS priority is mapped. Four traffic priority queues are supported. The Restore Defaults button restores the device factory defaults for mapping CoS values to a forwarding queue. CoS Default Interface Interface to which the CoS configuration applies. Default CoS Determines the default CoS value for i

  • Cisco SRW208 - Small Business Managed Switch, 76 Regulatory Information 8-Port 10/100 Ethernet Switch with Webview Appendix F User Information for Consumer Products Covered by EU Directive 2002/96/EC on Waste Electric and Electronic Equipment (WEEE) This document contains important information for users with regards to the proper disposal and recycling of Linksys products. Consumers are required to comply with this notice for all electronic products bearing the following symbol: English - Environmental Information for Customers in the Eu

  • Chapter 5 Advanced Configuration 44 8-Port 10/100 Ethernet Switch with Webview network topologies that allow a faster STP convergence without creating forwarding loops. Interface Displays the port or LAG on which Rapid STP is enabled. Role Indicates the port role assigned by the STP algorithm in order to provide to STP paths. The possible field values are: Root • Provides t

  • Cisco SRW208 - Small Business Managed Switch, 75 Regulatory Information 8-Port 10/100 Ethernet Switch with Webview Appendix F Appendix F: Regulatory Information FCC Statement This equipment has been tested and complies with the specifications for a Class A digital device, pursuant to Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. These limits are designed to provide reasonable protection against harmful interference when equipment is op

  • Cisco SRW208 - Small Business Managed Switch, Chapter 5 Advanced Configuration 55 8-Port 10/100 Ethernet Switch with Webview Cable Length This is the approximate length of the cable. The Cable Length test can be performed only when the port is up and operating at 1Gbps. Admin > Save Configuration Admin > Save Configuration Via TFTP After you download a new image file, the device should be rebooted. If you are downloading a new boot image, please follow these steps: Download the new boot code.1. WARNING: While inputting the boot code, refrain from reseting the device. Download the new software image. 2. Reset the device now.3. Upgrade

  • Cisco SRW208 - Small Business Managed Switch, Chapter 5 Advanced Configuration 33 8-Port 10/100 Ethernet Switch with Webview The MAC Based ACL screen allows a MAC based ACL to be defined. ACEs can be added only if the ACL is not bound to an interface. ACL Name Displays the user-defined MAC based ACLs. New ACL Name Specifies a new user-defined MAC based ACL name. Delete ACL Deletes the selected ACL. Action Indicates the ACL forwarding action. Possible field values are: Permit • Forwards packets which meet the ACL criteria. Deny • Drops packets which meet the ACL criteria. Shutdown • Drops packet that meet the ACL

  • Cisco SRW208 - Small Business Managed Switch, 60 Downloading Using Xmodem 8-Port 10/100 Ethernet Switch with Webview Appendix B Press 9. Send and the software is downloaded. Download After the software has been downloaded, the device will reboot automatically.

  • Cisco SRW208 - Small Business Managed Switch, 5 Installation 8-Port 10/100 Ethernet Switch with Webview Chapter 3 Chapter 3: Installation Overview This chapter will explain how to connect network devices to the Switch. The following diagram shows a typical network configuration. Internet Cable/ DSL Modem Router Uplink via Fiber to Switch Administrator’s Notebook Wireless Access Point Desktop Notebook Typical Network Configuration When you connect your network devices, make sure you don’t exceed the maximum cabling distance of 100 meters (328 feet). Positioning

  • Cisco SRW208 - Small Business Managed Switch, 6 Installation 8-Port 10/100 Ethernet Switch with Webview Chapter 3 Rack-Mount Placement When rack-mounting the Switch, please observe the following guidelines: Elevated Operating Ambient • If installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack environment may be greater than room ambient. Therefore, consideration should be given to installing the equipment in an environment compatible with the maximum ambient temperature (Tma) specified by the manufacturer. Reduced Air Flow • Installation of the equipment i

  • Cisco SRW208 - Small Business Managed Switch, 8 Installation 8-Port 10/100 Ethernet Switch with Webview Chapter 3 Hardware Installation To connect network devices to the Switch, follow these instructions: Make sure all the devices you will connect to the Switch 1. are powered off. For 10/100Mbps devices, connect a Category 5 Ethernet 2. network cable to one of the numbered ports on the Switch. For a 1000Mbps device, connect a Category 5e Ethernet network cable to one of the numbered ports on the Switch. Connect the other end to a PC or other network 3. device. Repeat steps 2 and 3 to connect additional devices.4.

  • Cisco SRW208 - Small Business Managed Switch, 1 Introduction 8-Port 10/100 Ethernet Switch with Webview Chapter 1 Chapter 1: Introduction Welcome This guide covers five product models. SRW208 • 8-port 10/100 Ethernet Switch with WebView.Includes 8 10/100 RJ-45 ports. SRW208G • 8-port 10/100 Ethernet Switch with WebView and Expansion Slots. Includes 8 10/100 RJ-45 ports and 1 10/100/1000 RJ-45 port and 1 MiniGBIC slot. SRW208L • 8-port 10/100 Ethernet Switch with WebView and 100Base-LX Uplink. Includes 8 10/100 RJ-45 ports and 1 MiniGBIC slot and 1 100LX Uplink port. SRW208MP • 8-port 10/100 Ethernet Switch with WebView and Maximum P

  • Cisco SRW208 - Small Business Managed Switch, 2 Product Overview 8-Port 10/100 Ethernet Switch with Webview Chapter 2 Chapter 2: Product Overview SRW208 - Front Panel The LEDs and ports are located on the front panel of the Switch. Front Panel SYSTEM (Green) The system LED lights up to indicate that the Switch is powered on. LINK/ACT (Green) The LINK/ACT LED lights up to indicate a functional network link through the corresponding port (1 through 8) with an attached device. It flashes to indicate that the Switch is actively sending or receiving data over t

  • Cisco SRW208 - Small Business Managed Switch, Chapter 5 Advanced Configuration 20 8-Port 10/100 Ethernet Switch with Webview DNS Server Enter the primary DNS Server information. Click the Save Settings button to save your changes or click Cancel Changes to discard the information. Setup > Time The Time screen allows you to configure the time settings for the Switch. Setup > Time Set Time Use System Time When this option is selected, the local hardware clock is utilized. Use SNTP Time When this option is selected, the time is synchronized to an SNTP (Simple Network Time Protocol) server.. Local Time Hours The hour can be entered here. Minutes The minutes

  • Cisco SRW208 - Small Business Managed Switch, Chapter 5 Advanced Configuration 49 8-Port 10/100 Ethernet Switch with Webview SNMP > Group Profile SNMP > Group Profile The Group Profile screen provides information for creating SNMP groups and assigning SNMP access control privileges to SNMP groups. Groups allow network managers to assign access rights to specific device features, or features aspects. Group Name Displays the user-defined group to which access control rules are applied. The field range is up to 30 characters. Security Model Defines the SNMP version attached to the group. The possible field values are: SNMPv1 • SNMPv1 is defined for the group.

  • Cisco SRW208 - Small Business Managed Switch, Chapter 5 Advanced Configuration 56 8-Port 10/100 Ethernet Switch with Webview NOTE: When downloading a configuration file, make sure that it is a valid configuration file. If you have edited the file, ensure that only valid entries have been configured. Admin > Reboot Admin > Reboot The Reboot screen resets the device. The device configuration is automatically saved before the device is rebooted. Admin > Factory Defaults The Factory Reset screen allows network managers to reset the device to the factory defaults shipped with the switch. Restoring factory defaults results in erasing the configur

  • Cisco SRW208 - Small Business Managed Switch, iii Table of Contents 8-Port 10/100 Ethernet Switch with Webview Port Conguration Detail. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 Port Management > Link Aggregation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 Link Aggregation Detail. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 Port Management > LACP . . . . . . . . . . . . . . . . . . . . . . . . . . . .

  • Cisco SRW208 - Small Business Managed Switch, Chapter 5 Advanced Configuration 43 8-Port 10/100 Ethernet Switch with Webview Spanning Tree > STP Port Settings Spanning Tree > STP Port Settings Network administrators can assign STP settings to specific interfaces using the STP Interface Settings screen. The STP Interface Settings screen contains the following fields: Interface Indicates the port or LAG on which STP is enabled. STP Indicates if STP is enabled on the port. Port Fast Indicates if Fast Link is enabled on the port. If Fast Link mode is enabled for a port, the Port State

  • Cisco SRW208 - Small Business Managed Switch, Chapter 5 Advanced Configuration 54 8-Port 10/100 Ethernet Switch with Webview all error reporting. For example, Syslog and local device reporting messages are assigned a severity code, and include a message mnemonic, which identifies the source application generating the message. It allows messages to be filtered based on their urgency or relevancy. Each message severity determines the set of event logging devices that are sent per each event logging. Logging Indicates

  • Cisco SRW208 - Small Business Managed Switch, 10 Configuration Using the Console Interface 8-Port 10/100 Ethernet Switch with Webview Chapter 4 Press the Esc button and you will return to the login screen. Use the right arrow button to navigate to Execute and press the Enter button to enter the CLI interface. Configuring the Switch through the Console Interface The console screens consist of a series of menus. Each menu has several options, which are listed vertically. You select a menu option when you highlight it; pressing the Enter key activates the highlighted option. To navigate through the menus and actions of the console interface

Related Products and Documents (Switch):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Power Acoustik 4DS-400 Introduction manual power-acoustik/4ds-400-49F.pdf 15 Sep 2023 9
2 American DJ FS-6C User instructions american-dj/fs-6c-6TM.pdf 14 Aug 2023 1 0.02 Mb
3 LevelOne FCS-5061 Operation & user’s manual levelone/fcs-5061-2O8.pdf 05 Aug 2023 106
4 Bull NovaScale Blade BL265 Installation and user manual bull/novascale-blade-bl265-68G.pdf 22 Oct 2022 92
5 Oster PANINI MAKER / GRILL Operation & user’s manual oster/panini-maker-grill-B6H.pdf 07 Mar 2024 7
6 Jonsered GR2036 Operator's manual jonsered/gr2036-473.pdf 27 Jul 2022 40

Similar Resources:

  • Aotec

    ZW096

    (2 pages)
    View the expanded manual:http://aeotec.com/supportSmart Switch 6Aeotec by Aeon Labs Smart Switch.Aeotec Smart Switch is a low-cost Z-Wave Switch plug-in module specically used to enable Z-Wave command and control (on/off) of any plug-in tool. It can report immediate wattage consumption or kWh energy usage over a period of time. In the event of …
  • Makita

    BVR340

    (36 pages)
    1 1GB Cordless Concrete Vibrator INSTRUCTION MANUAL UA Бездротовий вібратор для бетонуІНСТРУКЦІЯ З ЕКСПЛУАТАЦІЇ PL Akumulatorowy wibrator do masy betonowejINSTRUKCJA OBSŁUGI RO Vibrator de beton cu acumulator MANUAL DE INSTRUCŢIUNI DE Akku-Betonrüttler BEDIENUNGSANLEITUNG HU Akkumulátoros betonvibrát …
  • MS Sedco

    216TX

    (2 pages)
    TX PCBBATTERY216TXActive Infrared Wireless Touchless Switch INSTALLATION INSTRUCTIONSPage 1216TXv1017Section 1General DescriptionThe 216TX Wireless Touchless switches are active infrared devices designed for hands-free activation of automatic door operators or other access control products. The 216TX switch assembly includes the 1020 mounting box and trans …
  • DeviceWell

    HDS7105

    (38 pages)
    Website: www.devicewell.com Email: [email protected] 1 HDS7105 SWITCHER Model: HDS7105 VER2.0 Users’ Manual HD …
  • Tripp Lite

    B004-VPA2-K-R

    (2 pages)
    IntroductionLe B004-VPA2-K-R est un commutateur compact PS/2 KVM à 2 ports avec fonction optionnelle de commutation audio et microphone. Il vous permet d’accéder, de commander, démarrer et redémarrer plusieurs ordinateurs activés PS/2 à l’aide d’un simple clavier d’un moniteur, d’une souris et d’un ensemble de haut-parleurs et d’un microp …
  • Samsung

    HT-F4500

    (76 pages)
    imagine the possibilitiesThank you for purchasing this Samsung product.To receive more complete service,please register your product atwww.samsung.com/register5.1CH Blu-ray™Home Entertainment Systemuser manualHT-F4500HT-F4530HT-F4500_30_ZC_0205.indd 1HT-F4500_30_ZC_0205.indd 1 2013-02-07 오전 10:41:162013-02-07 오전 10:41:16 …

Comments, Questions and Opinions: