Cisco 888 Hardware Installation Manual
|
Cisco 888, 2-6 Cisco 800 Series Routers Hardware Installation Guide 78-5373-04 Chapter 2 Installation Installing Your Router Connecting Ethernet Devices Table 2-2 lists the Ethernet devices you can connect to the router, connections for each device, and the settings of the router HUB/NO HUB or TO HUB/TO PC button (the default setting is IN). Table 2-2 Connecting Ethernet Devices Network Device Connected to Router Router Port Ethernet Cable Type 1 Router HUB/NO HUB, TO HUB/TO PC Button Setting Network Device Button Setting 2 Hub with equivalent to router HUB/NO HUB button Cisco 801 and 802 routers: Et
Cisco 888, CHAPTER 3-1 Cisco 800 Series Routers Hardware Installation Guide 78-5373-04 3 Troubleshooting This chapter describes problems that could occur with the Cisco 800 series router hardware, reasons for the problems, and steps to solve the problems. The problems are grouped as follows: • Problems during first startup • Problems after first startup • Problems after router is running For information on problems that could occur with the software, refer to the Cisco 800 Series Routers Software Configuration Guide.
Cisco 888, Cisco 800 Series Routers Hardware Installation Guide Copyright © 2005 Cisco Systems, Inc. All rights reserved. CCSP, CCVP, the Cisco Square Bridge logo, Follow Me Browsing, and StackWise are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn, and iQuick Study are service marks of Cisco Systems, Inc.; and Access Registrar, Aironet, ASIST, BPX, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, Cisco, the Cisco Certified Internetwork Expert logo, Cisco IOS, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Cisco Unity
Cisco 888, vii Cisco 800 Series Routers Hardware Installation Guide 78-5373-04 About This Guide This preface discusses the audience, organization, and conventions used in this guide. Audience This guide is intended for service technicians with all levels of experience in installing routers. The goal of all technicians is to connect the router to the network as quickly as possible. Where relevant, this guide explains how the router is implemented and why. Conceptual information is usually in a separate section or appendix so that technicians who are not interested can skip this information. Organization This guide contains the following information: • About Th
Cisco 888, 3-5 Cisco 800 Series Routers Hardware Installation Guide 78-5373-04 Chapter 3 Troubleshooting Problems After Router Is Running Problems After Router Is Running Table 3-3 lists problems that could occur after the router has been up and running for a while. • Problem with ISDN line. • Contact your telephone service provider to determine if there is a problem with your line. • If the problem continues, call your Cisco reseller. Table 3-2 Problems After First Startup (continued) Symptom Problem Solutions Table 3-3 Problems After Router Is Running Symptom Problem Solutions Problems with Ethernet link. (On Cisco
Contents vi Cisco 800 Series Routers Hardware Installation Guide 78-5373-04 Installing Your Router 2-5 Connecting Ethernet Devices 2-6 Connecting an ISDN Line 2-10 Connecting an IDSL Line 2-13 Connecting a Digital Telephone 2-14 Connecting an Analog Telephone, Fax, or Modem 2-15 Connecting a Terminal or PC 2-17 Connecting the Power Supply 2-18 Mounting Your Router
Cisco 888, 2-19 Cisco 800 Series Routers Hardware Installation Guide 78-5373-04 Chapter 2 Installation Mounting Your Router • Do not cover or obstruct router vents, which are located on the router sides. • You can stack a maximum of five routers atop one another. Mounting on a Wall You can mount your router on a wall or other vertical surface by using the molded mounting brackets on the bottom of the router and two number-six, 3/4-in. (M3.5 x 20 mm) screws. You must provide the screws. Figure 2-
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS. THE SOFTWARE LICENSE A
Cisco 888, 2-7 Cisco 800 Series Routers Hardware Installation Guide 78-5373-04 Chapter 2 Installation Installing Your Router Server, PC, or workstation Cisco 801 and 802 routers: Ethernet port Cisco 803 and 804 routers: Ethernet port Ø Straight-through OUT N/A Server, PC, or workstation Cisco 802 IDSL router: Ethernet port Cisco 804 IDSL router: Ethernet port 1 Straight-through OUT N/A Server, PC, or workstation Cisco 803 and 804 routers: Ethernet ports 1, 2, 3 Straight-through N/A 3 N/A Server, PC, or workstation Cisco 804 IDSL router: Ethernet ports 2, 3, 4 Straight-through N/A 4 N/A 1. Cisco provides a yellow straight-through cable. You provide crossover o
B-7 Cisco 800 Series Routers Hardware Installation Guide 78-5373-04 Appendix B Specifications and Cables Cabling Specifications Ethernet Cable Specifications Table B-13 lists the specifications for straight-through and crossover Ethernet cables. Refer to the Glossary for definitions of straight-through Ethernet cable and crossover Ethernet cable. Maximum Cable D
Cisco 888, 3-4 Cisco 800 Series Routers Hardware Installation Guide 78-5373-04 Chapter 3 Troubleshooting Problems After First Startup • One of the following cable-related problems: – Improperly connected cable. – Damaged cable. Perform the following tasks in the following order: • To make sure you have cabled the ISDN or IDSL port correctly, see the “Connecting an ISDN Line” or “Connecting an IDSL Line” sections in Chapter 2, “Installation.” • Make sure the connectors at both ends of each cable are securely connected. • Make sure each cable is not physically damaged. If it is, replac
Cisco 888, 1-8 Cisco 800 Series Routers Hardware Installation Guide 78-5373-04 Chapter 1 Overview LEDs Note On Cisco 802 IDSL and Cisco 804 IDSL routers, either CH1 or CH2 is on if the router has an active data connection and the line speed is 64 kbps. CH1 and CH2 are both on if the router has an active data connection and the line speed is 128 or 144 kbps. CH1 Orange Blinks when placing or receiving a call on the first ISDN B channel. On when a call is connected on the first ISDN B channel. For IDSL routers, see the Note following this table. C
Cisco 888, 2-8 Cisco 800 Series Routers Hardware Installation Guide 78-5373-04 Chapter 2 Installation Installing Your Router Connecting Hubs If you have a Cisco 803, 804, or 804 IDSL router, you can connect as many as four hubs. Before connecting a hub, see Table 2-2, and do the following: • Choose Ethernet cables. • On the router, set the HUB/NO HUB or TO HUB/TO PC button. • On the hub, set the HUB/NO HUB button or its equivalent. Follow the steps in Figure 2-1 to connect a hub to a Cisco 800 series ISDN or IDSL router. This figure shows a Cisco 803 router wi
2-21 Cisco 800 Series Routers Hardware Installation Guide 78-5373-04 Chapter 2 Installation Verifying Installation Table 2-4 Verifying Installation Power/Link LEDs To Check Normal Patterns Power OK On To hub, server, PC, or workstation • Cisco 801, 802, and 802 IDSL routers: LINK, LAN, LAN RXD, and LAN TXD • Cisco 803 and Cisco 804 routers: LK�
Cisco 888, Index IN-2 Cisco 800 Series Routers Hardware Installation Guide 78-5373-04 F fax, connecting 2-15 Flash memory, adding 1-2 frequency specifications B-1 front panels, illustrated 1-3 H hazard statements, defined vii HUB/NO HUB button illustrated 1-4 to 1-6 settings 2-6 to 2-7 hubs, connecting 2-8 humidity specifications B-1 I IDSL concepts A-1 IDSL LEDs, illustrated 1-4 IDSL line, connecting 2-13 IDSL port described 1-2 illustrated 1-6, 1-7 installation verifying 2-20 warnings 2-2 ISDN concepts A-1 ISDN line, connecting 2-10 to 2-13 ISDN S/T port described 1-2 illustr
Cisco 888, 1-4 Cisco 800 Series Routers Hardware Installation Guide 78-5373-04 Chapter 1 Overview Back Panels Figure 1-3 Cisco 804 IDSL Front Panel Back Panels The figures in this section show the back panel of each of the Cisco 800 series routers. If the symbol of suitability ( ) appears above a port, you can connect the port directly to a public network that follows the European Union standards. Warning If the symbol of suitability with an overlaid cross ( ) appears above a port, you must not connect the port to a public network that follows the European Union standards. Connecting the port to this type of public network can cause severe injury or damag
Cisco 888, 2-15 Cisco 800 Series Routers Hardware Installation Guide 78-5373-04 Chapter 2 Installation Installing Your Router To connect a digital telephone, follow the steps in Figure 2-7. You must provide the following equipment: • NT1 with two S/T interfaces and one U interface. • Telephone cable to connect digital telephone. (This cable is usually provided with the telephone.) • ISDN U cable that connects the NT1 to the ISDN wall jack. Figure 2-7 Connecting Digital Telephone to Cisco 801 and Cisco 803 Routers Connecting an Analog Telephone, Fax, or Modem If you have Cisco 803 or Cisco 804 route
Cisco 888, viii Cisco 800 Series Routers Hardware Installation Guide 78-5373-04 About This Guide Conventions Caution This symbol means reader be careful. In this situation, you might do something that could result in equipment damage or loss of data. Warning This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with the standard practices for preventing accidents. Waarschuwing
Cisco 888, 2-13 Cisco 800 Series Routers Hardware Installation Guide 78-5373-04 Chapter 2 Installation Installing Your Router Figure 2-5 Connecting ISDN to Cisco 802 or Cisco 804 Routers Connecting an IDSL Line Warning Network hazardous voltages are present in the IDSL cable. If you detach the IDSL cable, detach the end away from the router first to avoid possible electric shock. Network hazardous voltages also are present on the system card in the area of the IDSL port (RJ-45 connector), regardless of when power is turned to standby. Warning Do not work on the system or connect or disconnect cables during periods of lightning activity. Warning To reduce the risk of
Cisco 888, B-3 Cisco 800 Series Routers Hardware Installation Guide 78-5373-04 Appendix B Specifications and Cables Port Connector Pinouts Table B-4 Cisco 804 IDSL Ethernet Connector Pinouts for Port 1 Only (RJ-45) Pin Function (TO HUB/TO PC Button – OUT Position) Function (TO HUB/TO PC Button – IN Position) Pin Function (TO HUB/TO PC Button – OUT Position) Function (TO HUB/TO PC Button – IN Position) A1 RX+ TX+ A2 RX– TX– A3 TX+ RX+ A4 Unused Unused A5 Unused Unused A6 TX– RX– A7 Unused Unused A8 Unused Unused Ta
Cisco 888, xii Cisco 800 Series Routers Hardware Installation Guide 78-5373-04 About This Guide Obtaining Additional Publications and Information Submitting a Service Request Using the online TAC Service Request Tool is the fastest way to open S3 and S4 service requests. (S3 and S4 service requests are those in which your network is minimally impaired or for which you require product information.) After you describe your situation, the TAC Service Request Tool provides recommended solutions. If your issue is not resolved using the recommended resources, your service request is assigned to a Cisco TAC engineer. The T
GL-1 Cisco 800 Series Routers Hardware Installation Guide 78-5373-04 GLOSSARY Numerics 10BASE-T The 10-Mbps baseband Ethernet specification that uses two pairs of twisted-pair cabling (Category 3 or 5): one pair for transmitting data and the other for receiving data. B BRI Basic Rate Interface. An ISDN interface composed of two bearer channels (B channels) an
Cisco 888, xi Cisco 800 Series Routers Hardware Installation Guide 78-5373-04 About This Guide Obtaining Technical Assistance Tip We encourage you to use Pretty Good Privacy (PGP) or a compatible product to encrypt any sensitive information that you send to Cisco. PSIRT can work from encrypted information that is compatible with PGP versions 2.x through 8.x. Never use a revoked or an expired encryption key. The correct public key to use in your correspondence with PSIRT is the one that has the most recent creation date in this public key server list: http://pgp.mit.edu:11371/pks/lookup?search=psirt%40cisco.com&op=index&exact=on In an emergency, you can also reach PSI
Cisco 888, 1-6 Cisco 800 Series Routers Hardware Installation Guide 78-5373-04 Chapter 1 Overview Back Panels Figure 1-7 Cisco 804 Router Back Panel Figure 1-8 Cisco 802 IDSL Router Back Panel 11669 ISDN U Cable lock Use cable lock to physically secure router. Ethernet ports Connect Ethernet network devices. Console port Connect PC or terminal. ISDN BRI U port Connect to ISDN wall jack. Telephone ports Connect to telephone, fax machine, or modem. Locking power connector Connect power supply. 1
1-5 Cisco 800 Series Routers Hardware Installation Guide 78-5373-04 Chapter 1 Overview Back Panels Figure 1-5 Cisco 802 Router Back Panel Figure 1-6 Cisco 803 Router Back Panel 11667 ISDN U CONSOLE ETHERNET Cable lock Use cable lock to physically secure router. Link LED Indicates state of Ethernet port. HUB/NO HUB button (for Ethernet port) Determines cable
Cisco Catalyst 4500 Series Network Router Message manual
Catalyst 4500 Series |
Cisco 2611XM Network Router Datasheet
2611XM |
Cisco WRT55AG Network Router Quick installation
WRT55AG |
Cisco Catalyst 3750-X Network Router Message manual
Catalyst 3750-X |
Cisco Aironet 2600 Series Network Router Datasheet
Aironet 2600 Series |
Cisco RV016 - Small Business - 10/100 VPN Router Network Router Administration manual
RV016 - Small Business - 10/100 VPN Router |
Cisco ME-C6524GS-8S Network Router Installation manual
ME-C6524GS-8S |
Cisco AIR-AP1230B-A-K9 - Syst. 1230 Aironet WLAN AP Network Router Hardware installation manual
AIR-AP1230B-A-K9 - Syst. 1230 Aironet WLAN AP |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | Aironet | 4800B Series | Quick start manual | aironet/4800b-series-862.pdf | 27 Sep 2022 | 15 | |
2 | Altair | FA-524 | Owner's manual | altair/fa-524-48L.pdf | 03 Jan 2023 | 40 | |
3 | Sierra Wireless | IP Manager | Configuration | sierra-wireless/ip-manager-QZA.pdf | 01 Nov 2023 | 16 | 0.51 Mb |
4 | GE | Dishwashers | Owner's manual | ge/dishwashers-18I.pdf | 12 Oct 2023 | 32 | 1.82 Mb |
5 | Boss Audio Systems | CAP4C | Operation & user’s manual | boss-audio-systems/cap4c-JVN.pdf | 23 Oct 2023 | 7 | 1.17 Mb |
6 | Panasonic | 2SC2404 | Specification sheet | panasonic/2sc2404-RG3.pdf | 16 Sep 2023 | 4 | 0.24 Mb |
On-Q
301 Fulling Mill Road, Suite G ©Copyright 2004 by OnQ Technologies, Middletown, PA 17057 Inc All Rights Reserved. (800) 321-2343 www.onqhome.com ()4Innovations in Home Living. 301 Fulling Mill Road, Suite G ©Copyright 2004 by OnQ Technologies, Middletown, PA 17057 Inc All Rights Re …
364772-01(21 pages) |
NETGEAR
Installation GuideFollow these quick steps to install your bridge.Note: Before you begin, have your wireless network set up and working.11Set up the ME101 Wireless Ethernet Bridgea. Unpack the box and verify the contents.b. Place the bridge away from potential sources of interference, such as computers, monitors, TVs, microwaves, cordless phones, or large me …
ME101 - Wireless EN Bridge Network Converter(2 pages) |
D-Link
1WIRELESS N QUADBAND HOME ROUTERDIR-825Quick Installation Guide+Installations-Anleitung+Guide d’installation+Guía de instalación+Guida di Installazione+Installatiehandleiding+Instrukcja instalacji+Instalační příručka+Telepítési Segédlet+Installasjonsveiledning+Installationsvejledning+Asennusopas+Installationsguide+Guia de Instalação+Οδηγό� …
DIR-825 - Xtreme N Dual Band Gigabit Router Wireless(40 pages) |
NETGEAR
Quick StartPackage ContentsThe box contains the following items.In some regions, a resource CD is included in the package.AC1750 Smart WiFi RouterModel R6400SupportThank you for purchasing this NETGEAR product.After installing your device, locate the serial number on the label of your product and use it to register your product at https://my.netgear.com. You …
R6400(22 pages) |
SMC Networks
Barricade Broadband RouterV1.0Quick Start GuideInstallationskurzanleitungGuide d'installationManual de instalación rápidaGuida rapida di installazione10/100Mbps Broadband Router10/100-MBit/s-BreitbandrouterRouteur haut débit 10/100MbpsRouter de banda ancha de 10/100 MbpsRouter a banda larga a 10/100 MbpsSMC7004VBRSMC7004VBR_QS.joint.qxd 19/9/02 12: …
7004VBR(109 pages) |
AudioCodes
Version 6.8 / 7.0 May 2016 Quick Setup Guide BroadCloud SIP-Trunking Service using AudioCodes Mediant BRI/PRI Gateway BRI/PRI Media Gateways AudioCodes Mediant™ Series
…
Mediant Series(48 pages) |
Philips Telephone Accessories SJA9192PDF Manual (@E12L5M), Philips SJA9192 Telephone Accessories (25.01.2024) SJA9192, 2 |
Bulldog Security Scrubber WD20Bulldog Security WD20 User Guide (Operation & user’s manual), @P342F6 WD20, 20 |
Audiovox CD Player PAV6DAudiovox CD Player Operation & user’s manual (File: audiovox-pav6d-car-stereo-system-58, 22.09.2023) PAV6D, 58 |
4xem Security Camera WFDI4xem Security Camera WFDI Supplementary manual WFDI, 2 |
Sony Monitor FWDS42E1Sony Monitor FWDS42E1 Operating instructions manual FWDS42E1, 255 |
Moog Receiver VLRM58Moog Receiver VLRM58 Installation and operation instructions manual VLRM58, 12 |
Wet Sounds Subwoofer XS-12Subwoofer PDF Owner's manual XS-12, 4 |
EKF Computer Hardware SC2-PRESTO CompactPCI#246YS6 SC2-PRESTO CompactPCI: EKF Computer Hardware Owner Documentation SC2-PRESTO CompactPCI, 84 |
ATEN Switch CS1782ACS1782A Quick start manual - 5HU512 CS1782A, 2 |
LaCie Network Card 400USBUser Guide: LaCie 400USB (6QMAMI, Upd.Friday 18-08-2023) 400USB, 39 |
Yamaha Offroad Vehicle RAPTOR 80Offroad Vehicle #74Z45V RAPTOR 80, 134 |
Aroma Toaster ATS-102Aroma ATS-102 Guide (Instruction manual), @8R3119 ATS-102, 5 |