Cisco Small Business 300 Quick Start Manual

Text of Cisco Small Business 300 User Guide:

• Cisco Small Business 300, 2 300 Series Managed Switches Welcome Thank you for choosing the Cisco 300 Series Managed Switch, a Cisco Small Business network communications device. This device is designed to be operational right out of the box as a standard bridge. In the default configuration, it will forward packets between connecting devices after power up. Package Contents • Cisco SF 300-08, SF 302-08, SF 302-08MP, SF 302-08P, SG 300-10, SG 300-10MP, SG 300-10P, SG 300-20, SF 300-24, SF 300-24P, SG 300-28, SG 300-28P, SF 300-48, SF 300-48P, or SG 300-52 Managed Switch • Rackmount Kit • Wall Mount Kit • Power Cord (power adapter in

• Cisco Small Business 300, 300 Series Managed Switches 3 Mechanical Overloading—The device should be level, stable, and secure to prevent it from sliding or shifting out of position. Circuit Overloading—Adding the device to the power outlet must not overload that circuit. Rack-Mount Placement To rack-mount the switch in any standard rack, attach the rack–mount brackets to the sides of the switch with the supplied hardware and secure the brackets tightly. CAUTION For stability, load the rack from the bottom to the top, with the heaviest devices on the bottom. A top-heavy rack is likely to be uns

• Cisco Small Business 300, 4 300 Series Managed Switches WARNING Insecure mounting may damage the device or cause injury. Cisco is not responsible for damages incurred by insecure wall- mounting. Connecting Network Devices To connect the managed switch to the network: STEP 1 Connect the Ethernet cable to the Ethernet port of a computer, printer, network storage, or other network device. STEP 2 Connect the other end of the network Ethernet cable to one of the numbered managed switch Ethernet ports. The LED of the port lights if the device connected is active. Refer to Features of the Cisco Small Business Managed Switch, page 9

• Cisco Small Business 300, 300 Series Managed Switches 5 Configuring the Cisco Small Business Managed Switch Before You Begin Verify that a computer with Microsoft Internet Explorer (version 6 and higher) or Firefox (version 2.0 or higher) is available. The switch can be accessed and managed by two different methods; over your IP network using the web-based interface, or by the menu CLI through the console port. Using the console port requires advanced user skills. The switch works with Cisco Small Business network tools and services including the Cisco FindIT Network Discovery Utility that enables you to automatically discovers all supported Cisco Small Business devices in the

• Cisco Small Business 300, 6 300 Series Managed Switches S TEP 3 Set up the IP configuration on your computer. a. If the switch is using the default static IP address of 192.168.1.254, you must chose an IP address in the range of 192.168.1.1-192.168.1.253 that is not already in use. b. If the IP addresses will be assigned by DHCP, make sure your DHCP server is running and can be reached from the switch and the computer. You may need to disconnect and reconnect the devices for them to discover their new IP addresses from the DHCP server. NOTE Detai

• Cisco Small Business 300, 300 Series Managed Switches 7 Use the console port To configure the managed switch: STEP 1 Connect a computer to the switch console port using the provided console port cable. STEP 2 Start a console port utility such as HyperTerminal on the computer. STEP 3 Configure the utility with the following parameters: • 115200 bits per second • 8 data bits • no parity • 1 stop bit • no flow control STEP 4 Enter a user name and password. User names and passwords are both case sensitive and alpha-numeric. The default username is cisco, and the default password is cisco. STEP 5 If this is the first

• 8 300 Series Managed Switches Troubleshoot Your Connection If you cannot access your switch from the web-based interface, the switch may not be reachable from your computer. You can test network connections by using ping on a computer running Windows: STEP 1 Open a command window by using Start > Run and enter cmd. STEP 2 At the Command window prompt enter

• Cisco Small Business 300, 300 Series Managed Switches 9 No IP route: If the switch and your computer are in different IP subnets, you need one or more routers to route the packets between the two subnets. Unusually long access time: Due to the standard spanning tree loop detection logic, adding new connections may take 30 to 60 seconds for the affected interfaces and/or LAN to become operational. Features of the Cisco Small Business Managed Switch This section describes the exterior of the managed switches including ports, LEDs, and connections. Front Pane

• Cisco Small Business 300, 10 300 Series Managed Switches Front Panel LEDs System LED—(Green) Lights steady when the switch is powered on, and flashes when booting, performing self tests, and acquiring an IP address. If the LED flashes Amber, the switch has detected a hardware failure. LINK/ACT LED—(Green) Located on the left of the port. Lights steady when a link between the corresponding port and another device is detected. Flashes when the port is passing traffic. NOTE The System and LINK/ACT LEDs are on each model of the switch. The following LEDs are only present on switch models that have those capabilities:

• Cisco Small Business 300, 300 Series Managed Switches 11 Back Panel The power port and console port are located on the back panel of the managed switch. Power—The Power port is where you will connect the switch to power. Console—The Console port is where you can connect a serial cable to a computers serial port for configuration using a terminal emulation program. Returning the Device to the Factory Default Settings To use the Reset button to reboot or reset the managed switch, do the following: •To reboot the managed switch, press the Reset button for less than 10 seconds. • To restore the mana

• 12 300 Series Managed Switches Where to Go From Here Support Cisco Small Business Support Community https://supportforums.cisco.com/community/ netpro/small-business Cisco Small Business Support and Resources http://www.cisco.com/cisco/web/solutions/ small_business/ small_business_support_and_resources.html Phone Support Contacts http://www.cisco.com/en/US/support/ tsd_

• Cisco Small Business 300, Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA www.cisco.com Small Business Support US: 1-866-606-1866 (Toll Free, 24/7) Small Business Support, Global: www.cisco.com/go/sbsc Cisco and the Cisco Logo are trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and other countries. A listing of Cisco's trademarks can be found at www.cisco.com/go/ trademarks. Third party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any oth

More Instructions:

	Cisco Small Business 300 Administration manual 12-06-2023 483	DOWNLOAD
	Cisco Small Business 300 Installation manual 07-03-2024 2	DOWNLOAD
	Cisco Small Business 300 Installation manual 18-10-2023 76	DOWNLOAD
	Cisco Small Business 300 Brochure & specs 25-02-2024 2	DOWNLOAD

Related Products and Documents (Switch):

Comparable Devices:

Similar Resources:

• Edge-Core ECS4120 Series (9 pages) – 1 –Quick Start Guide1. Unpack the Switch and Check ContentsECS4120-28TECS4120-28PECS4120-28FECS4120-28F-IECS4120-28Fv2ECS4120-28Fv2-IECS4120-52T28T/28P/52T Mounting Kit — 4 brackets and 10 screws28F/28F-I /28Fv2/28Fv2-I Mounting Kit — 2 brackets and 4 screwsFour adhesive foot padsPower cord — US, Continental Europe, or UKConsole cable — RJ-45 …

• Endress+Hauser Flowphant T DTT31 (20 pages) TI00125R/09/en71009492Technical informationFlow switchFlowphant® T DTT31, DTT35Flow switch for safe monitoring of mass flow and temperature in industrial processesApplicationFlow switch for monitoring and displaying relative mass flow rates of liquid media in the range from0.03 to 3 m/s (0.1 to 9.84 ft/s):Flowphant® T DTT31− with thread connections or co …

• Barco DCS-200 (2 pages) Quick Setup and Operations1Connect Power — Ensure that power is properly connected to the DCS-200. (Chapter 3, “Power Installation”)256Barco Media and Entertainment11101 Trade Center DriveRancho Cordova, CA 95670 • USAConnect Outputs — Connect the output(s) of the DCS-200 to your projector(s) or other target devices. (Chapter 3, “Signal Install …

• BD Sensors iS4 (2 pages) www.bdsensors.de EN Operating Manual Electronic OEM Pressure Switch Pneumatics with IO-Link Interface iS4 Headquarters BD SENSORS GmbH BD-Sensors-Str. 1 D - 95199 Thierstein Deutschland Tel.: +49 (0) 9235-9811-0 Fax: +49 (0) 9235-9811-11 Eastern Europe BD SENSORS s.r.o. Hradištská 817 CZ - 687 08 Buchlovice Tschechische Republic Tel.: +42 (0) 572-4110 …

• sauter AKM105 (3 pages) 1/3www.sauter-controls.comde Installationsanweisung für die Elektrofachkraft fr Notice d‘installation pour l‘électricienen Guidelines for the electricianit Informazioni per l‘installatore elettricoes Instrucciones de instalación para el electricistasv Installationsinstruktion för behörig elektrikernl Instalatie aanwijzing voor de elektromon …

• Crestron 4 Channel Inductor Module CLX-4IND (1 pages) EnvironmentalTemperature: 32° to 104°F (0° to 40°C) Humidity: 10% to 90% RH (non-condensing)EnclosureSurface mount chassis with (2) integral mounting flangesOccupies 1 module space in any CAEN enclosureDimensionsHeight: 7.40 in (18.80 cm)Width: 6.92 in (17.57 cm) Depth: 3.86 in (9.79 cm)Weight11.00 lb (4.99 kg)AVAILABLE ACCESSORIESCAEN Automation Enclosu …

Comments, Questions and Opinions: