Manualios.com

Cisco IPS-4260-K9 - IPS Sensor 4260 Installation Manual

  • IPS-4260-K9 - IPS Sensor 4260 PCI Card
  • makwLz0JYKCDE
  • Installation Manual
  • PDF / Adobe Acrobat Reader
  • 22

Cisco IPS-4260-K9 - IPS Sensor 4260 Manual Online:

4.75, 2040 votes
Cisco IPS-4260-K9 - IPS Sensor 4260 User Manual
Cisco IPS-4260-K9 - IPS Sensor 4260 User Guide
Cisco IPS-4260-K9 - IPS Sensor 4260 Online Manual

Text of Cisco IPS-4260-K9 - IPS Sensor 4260 User Guide:

  • Cisco IPS-4260-K9 - IPS Sensor 4260, CHAPTER 6-1 Installing Cisco Intrusion Prevention System Appliances and Modules 5.1 OL-8677-01 6 Installing IPS-4260 This chapter describes IPS-4260 and how to install it. It also describes the accessories and how to install them. This chapter contains the following sections: • Introducing IPS-4260, page 6-1 • Supported PCI Cards, page 6-2 • Hardware Bypass, page 6-3 • Front and Back Panel Features, page 6-5 • Specifications, page 6-8 • Accessories, page 6-8 • Rack Mounting, page 6-9 • Installing IPS-4260, page 6-14 • Removing and Replacing the Chassis Cover, page 6-17 •

  • Cisco IPS-4260-K9 - IPS Sensor 4260, 6-2 Installing Cisco Intrusion Prevention System Appliances and Modules 5.1 OL-8677-01 Chapter 6 Installing IPS-4260 Supported PCI Cards IPS-4260 has two built-in Gigabit Ethernet network ports and six expansion slots. The network port numbers increase from right to left and the expansion slot numbers increase from bottom to top and from right to left as shown in Figure 6-4 on page 6-6. Slots 2 and 3 are PCI-Express connectors and the other expansion slots are PCI-X slots. Slots 1 through 3 are full-height slots and slots 4 though 6 are half-height slots. The built-in management port is called Management0/0 and the built-in sensing inter

  • Cisco IPS-4260-K9 - IPS Sensor 4260, 6-3 Installing Cisco Intrusion Prevention System Appliances and Modules 5.1 OL-8677-01 Chapter 6 Installing IPS-4260 Hardware Bypass Figure 6-1 shows the 4GE bypass interface card. Figure 6-1 4GE Bypass Interface Card • 2SX Card (part number IPS-2SX-INT=) Provides two 1000BASE-SX (fiber) monitoring interfaces (allowing up to 4 total fiber monitoring interfaces). The 2SX interface cards does not support hardware bypass. Figure 6-2 shows the 2SX card. Figure 6-2 2SX Interface Card Hardware Bypass This section describes the 4GE bypass interfa

  • Cisco IPS-4260-K9 - IPS Sensor 4260, 6-4 Installing Cisco Intrusion Prevention System Appliances and Modules 5.1 OL-8677-01 Chapter 6 Installing IPS-4260 Hardware Bypass 4GE Bypass Interface card IPS-4260 supports the 4-port GigabitEthernet card (part number IPS-4GE-BP-INT=) with hardware bypass. This 4GE bypass interface card supports hardware bypass only between ports 0 and 1 and between ports 2 and 3. Figure 6-1 on page 6-3 shows the 4GE bypass interface card. Hardware bypass complements the existing software bypass feature in IPS 5.1. For more information on software bypass mode, refer to Configuring Bypass Mode. The following conditions appl

  • 6-5 Installing Cisco Intrusion Prevention System Appliances and Modules 5.1 OL-8677-01 Chapter 6 Installing IPS-4260 Front and Back Panel Features The following configuration restrictions apply to hardware bypass: • The 4-port bypass card is only supported on IPS-4260. • Fail-open hardware bypass only works on inline interfaces (interface pairs), not on inline

  • 6-6 Installing Cisco Intrusion Prevention System Appliances and Modules 5.1 OL-8677-01 Chapter 6 Installing IPS-4260 Front and Back Panel Features Table 6-1 describes the front panel indicators on IPS-4260. Figure 6-4 shows the back view of the IPS-4260. Figure 6-4 IPS-4260 Back Panel Features Table 6-1 Front Panel Indicators Indicator Description ID (blue) Continuously

  • 6-7 Installing Cisco Intrusion Prevention System Appliances and Modules 5.1 OL-8677-01 Chapter 6 Installing IPS-4260 Front and Back Panel Features Figure 6-5 shows the two built-in Ethernet ports, which have two indicators per port. Figure 6-5 Ethernet Port Indicators Table 6-2 lists the back panel indicators. Table 6-3 lists the power supply indi

  • Cisco IPS-4260-K9 - IPS Sensor 4260, 6-8 Installing Cisco Intrusion Prevention System Appliances and Modules 5.1 OL-8677-01 Chapter 6 Installing IPS-4260 Specifications Specifications Table 6-4 lists the specifications for IPS-4260. Accessories Warning IMPORTANT SAFETY INSTRUCTIONS This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Use the statement number provided at the end of each warning to locate its translation in the translated sa

  • Cisco IPS-4260-K9 - IPS Sensor 4260, 6-9 Installing Cisco Intrusion Prevention System Appliances and Modules 5.1 OL-8677-01 Chapter 6 Installing IPS-4260 Rack Mounting Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement 1030 IPS-4260 accessories kit contains the following: • DB25 connector • DB9 connector • Rack mounting kit—screws, washers, and metal bracket • RJ45 console cable • Two 6-ft Ethernet cables Rack Mounting You can rack mount IPS-4

  • Cisco IPS-4260-K9 - IPS Sensor 4260, 6-10 Installing Cisco Intrusion Prevention System Appliances and Modules 5.1 OL-8677-01 Chapter 6 Installing IPS-4260 Rack Mounting Step 2 Attach the front-tab mounting bracket to the chassis with two 8-32x1/4’ SEMS screws. You can flip the bracket to push the system forward in the rack. Step 3 Using the four inner studs, install the mounting brackets to the outer rail with four 8-32 KEPS nuts. Insert four thread covers over the four outer studs on each side. 153315 Cisco IPS 4260 se

  • Cisco IPS-4260-K9 - IPS Sensor 4260, 6-11 Installing Cisco Intrusion Prevention System Appliances and Modules 5.1 OL-8677-01 Chapter 6 Installing IPS-4260 Rack Mounting Step 4 Install the two outer rail subassemblies in the rack using eight 10-32x1/2” SEMS screws. You can use four bar nuts if necessary. Note Adjust the mounting brackets based on rack depth. Step 5 Slide IPS-4260 into the rack making sure the inner rail is aligned with the outer rail. Step 6 Install two 10-32x1/2” SEMS screws to hold the front-tab mounting bracket to the rail. 153317 153318 C isc o IP S 4 2 6 0 se rie s I

  • Cisco IPS-4260-K9 - IPS Sensor 4260, 6-12 Installing Cisco Intrusion Prevention System Appliances and Modules 5.1 OL-8677-01 Chapter 6 Installing IPS-4260 Rack Mounting Installing IPS-4260 in a 2-Post Rack To rack mount IPS-4260 in a 2-post rack, follow these steps: Step 1 Attach the inner rail to each side of the chassis with three 8-32x1/4” SEMS screws. Step 2 Using the four inner studs, install the mounting brackets to the outer rail with four 8-32 KEPS nuts. Insert four thread covers over the four outer studs on each side. Step 3 Install

  • Cisco IPS-4260-K9 - IPS Sensor 4260, 6-13 Installing Cisco Intrusion Prevention System Appliances and Modules 5.1 OL-8677-01 Chapter 6 Installing IPS-4260 Rack Mounting Step 4 Slide IPS-4260 into the rack making sure the inner rail is aligned with the outer rail. Step 5 Install four 8-32x7/16” SEMS screws through the clearance slots in the side of each outer rail assembly into the inner rail. 153322 153323 Cisco IPS 4260 series In tr u s io n P r e v e n tio n S e n s o r P O W E R S T A T U S F L A S H ID N I C R E S E T ID

  • Cisco IPS-4260-K9 - IPS Sensor 4260, 6-14 Installing Cisco Intrusion Prevention System Appliances and Modules 5.1 OL-8677-01 Chapter 6 Installing IPS-4260 Installing IPS-4260 Installing IPS-4260 Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement 1030 Caution Follow proper safety procedures when performing these steps by reading the safety warnings in Regulatory Compliance and Safety Information for the Cisco Intrusion Prevention System 4200 Series Appliance Sensor. For mor

  • Cisco IPS-4260-K9 - IPS Sensor 4260, 6-15 Installing Cisco Intrusion Prevention System Appliances and Modules 5.1 OL-8677-01 Chapter 6 Installing IPS-4260 Installing IPS-4260 Note Use 8-32 locknuts to connect a copper standard barrel grounding lug to the holes. The appliance requires a lug where the distance between the center of each hole is 0.56 inches. The ground lug must be NRTL listed or recognized. In addition, the copper conductor (wires) must be used and the copper conductor must comply with the NEC code for ampacity. A lug is no

  • Cisco IPS-4260-K9 - IPS Sensor 4260, 6-16 Installing Cisco Intrusion Prevention System Appliances and Modules 5.1 OL-8677-01 Chapter 6 Installing IPS-4260 Installing IPS-4260 Step 6 Connect the RJ-45 connector to the console port and connect the other end to the DB-9 or DB-25 connector on your computer. Step 7 Attach the network cables. IPS-4260 has the following interfaces: • GigabitEthernet0/1 (GE 0/1) is the sensing port. • Management0/0 (MGMT) is the command and control port. • GigabitEthernet2/0 through GigabitEthernet2/3 and GigabitEthernet3/0 through 3/3 are the additional expansion port slots. C

  • 6-17 Installing Cisco Intrusion Prevention System Appliances and Modules 5.1 OL-8677-01 Chapter 6 Installing IPS-4260 Removing and Replacing the Chassis Cover Step 9 Initialize IPS-4260. For the procedure, see Initializing the Sensor, page 10-2. Step 10 Upgrade IPS-4260 with the most recent Cisco IPS software. For the procedure, see Obtaining Cisco IPS Software, page 11-1. You ar

  • Cisco IPS-4260-K9 - IPS Sensor 4260, 6-18 Installing Cisco Intrusion Prevention System Appliances and Modules 5.1 OL-8677-01 Chapter 6 Installing IPS-4260 Removing and Replacing the Chassis Cover Note Removing the appliance chassis cover does not affect your Cisco warranty. Upgrading IPS-4260 does not require any special tools and does not create any radio frequency leaks. To remove and replace the chassis cover, follow these steps: Step 1 Log in to the CLI. Step 2 Prepare IPS-4260 to be powered off: sensor# reset powerdown Wait for the power down mes

  • Cisco IPS-4260-K9 - IPS Sensor 4260, 6-19 Installing Cisco Intrusion Prevention System Appliances and Modules 5.1 OL-8677-01 Chapter 6 Installing IPS-4260 Installing and Removing PCI Cards Step 10 Reinstall IPS-4260 on a rack, desktop, or table. If you are reinstalling in a rack, see Rack Mounting, page 6-9. Step 11 Power on IPS-4260. Installing and Removing PCI Cards IPS-4260 has 6 expansion card slots, three full-height and three half-height slots. You can install the optional network interface cards in the two top full-height s

  • Cisco IPS-4260-K9 - IPS Sensor 4260, 6-20 Installing Cisco Intrusion Prevention System Appliances and Modules 5.1 OL-8677-01 Chapter 6 Installing IPS-4260 Installing and Removing PCI Cards Step 8 Remove the card carrier by pulling up on the two blue release tabs. Use equal pressure and lift the card carrier out of the chassis. Step 9 With a screw driver, remove the screw from the desired slot cover. Step 10 Remove the slot cover by pressing on it from inside the chassis. If the card is full length, use a screw driver to remove the blue thumb sc

  • Cisco IPS-4260-K9 - IPS Sensor 4260, 6-21 Installing Cisco Intrusion Prevention System Appliances and Modules 5.1 OL-8677-01 Chapter 6 Installing IPS-4260 Installing and Removing the Power Supply Installing and Removing the Power Supply IPS-4260 ships with one power supply, but you can order it with two power supplies so that you have a redundant power supply. To install and remove power supplies, follow these steps: Step 1 Log in to the CLI. Step 2 Prepare IPS-4260 to be powered off: sensor# reset powerdown Wait for the power down message before continuing with Step 3. Note You can also power down IPS-4260 using IDM. For the procedure, refer to Resetting the Appliance. Step 3 Power o

  • Cisco IPS-4260-K9 - IPS Sensor 4260, 6-22 Installing Cisco Intrusion Prevention System Appliances and Modules 5.1 OL-8677-01 Chapter 6 Installing IPS-4260 Installing and Removing the Power Supply Step 6 Install the power supply. Step 7 To remove the power supply, push down the green tab and pull out the power supply. Step 8 After installing or removing the power supply, replace the power cord and other cables. Step 9 Power on IPS-4260. ! ! ! !

Related Products and Documents (PCI Card):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Carrier 38GJ Series Owner's manual & installation instructions carrier/38gj-series-IZU.pdf 12 Sep 2022 12
2 Grupo Epelsa K-scale Operation & user’s manual grupo-epelsa/k-scale-O7X.pdf 12 Jan 2023 92
3 Zanussi ZRB34ND Instruction book zanussi/zrb34nd-767.pdf 16 Aug 2022 16
4 Beko OUE 22120 Operation & user’s manual beko/oue-22120-86P.pdf 26 Apr 2023 88
5 Sartorius YDP12IS-0CEUV Installation instructions manual sartorius/ydp12is-0ceuv-1X1.pdf 28 Feb 2024 24
6 Ricoh MP C3003 Brochure & specs ricoh/mp-c3003-8D8.pdf 04 Apr 2023 12 1.57 Mb

Similar Resources:

  • ATCOM

    AX-1600P

    (12 pages)
    Figure: AX-1600PFigure: AX E -1600 PATCOMATCOMATCOMATCOM®®®®AnalogAnalogAnalogAnalog CardCardCardCard AX-AX-AX-AX- 1600P/1600P/1600P/1600P/ AXE1600PAXE1600PAXE1600PAXE1600PProductProductProductProduct GuideGuideGuideGuideVersion: 1. 1201 2 -0 7 - 07 …
  • Dell

    Latitude D500

    (40 pages)
    Dell™Latitude™D500ServiceManual Before You Begin Preparing to Work Inside the Computer Recommended Tools Computer Orientation Screw Identification Memory Module, Mini PCI Card, and Devices Memory Module Mini PCI Card Devices System Components Reserve Battery Hard Drive Keyboard Display Assembly and Display Latch Di …
  • National Instruments

    IMAQ PCI-1409

    (55 pages)
    IMAQ™IMAQ PCI/PXI™-1409User ManualHigh-Quality Monochrome Image Acquisition Boardsfor PCI, PXI, and CompactPCI BusIMAQ PCI/PXI-1409 User ManualNovember 2000 EditionPart Number 322811A-01 …
  • MGE UPS Systems

    minislot 66244

    (67 pages)
    www.mgeups.comNetworkManagement CardsUser ManualTHE UNINTERRUPTIBLE POWER PROVIDERNetwork Management Card – User Manual 34003676EN/BB Page 1/76Minislot 66244Transverse 66074Environment Sensor 66846 …
  • SilverStone

    ECM21-E

    (2 pages)
    ECM21-EScrewless design for M.2 PCIe/NVMe SSDSupports PCIe Gen4 M.2 PCIe/NVMe SSDCLKREQ jump pin header LED indicator for displaying M.2 PCIe/NVMe statusSupports 2230, 2242, 2260, and 2280 length M.2 SSDConverts M.2 port (M key) into one PCIe x4 interface ECM21-E x 1 M.2 SSD screw x 2 Screw nut x 1 Low profile bracket x 1Package ContentSpecificationsScrewles …
  • Asus

    XONAR PHOEBUS

    (122 pages)
    U7062 First Edition V1 Jan. 2012Xonar Phoebus PCI Express 7.1-Channel Gaming SoundcardQuick Start GuideU7062_Xonar-Phoebus_QSG.indb 1 18.01.2012 16:12:15 Uhr …

Comments, Questions and Opinions: