Cisco DS-X9530-SF1-K9 - Supervisor-1 Module - Control Processor Configuration Manual

Text of Cisco DS-X9530-SF1-K9 - Supervisor-1 Module - Control Processor User Guide:

• Cisco DS-X9530-SF1-K9 - Supervisor-1 Module - Control Processor, Send documentation comments to [email protected]. 24-27 Cisco MDS 9000 Family Configuration Guide OL-6973-03, Cisco MDS SAN-OS Release 2.x Chapter 24 Configuring FICON Moving a FICON VSAN to an Offline State Moving a FICON VSAN to an Offline State Issue the ficon vsan vsan-id offline command in EXEC mode to log out all ports in the VSAN that needs to be suspended. Issue the EXEC-level ficon vsan vsan-id online command in EXEC mode to remove the offline condition and to allow ports to log on again. Note This command can be i

• Cisco DS-X9530-SF1-K9 - Supervisor-1 Module - Control Processor, Send documentation comments to [email protected]. 49-15 Cisco MDS 9000 Family Configuration Guide OL-6973-03, Cisco MDS SAN-OS Release 2.x Chapter 49 Troubleshooting Your Fabric The show tech-support Command You can choose to have detailed information for each command or even specify the output for a particular interface, module or VSAN. Each command output is separated by line and the command precedes the output. Note Explicitly set the terminal length command to 0 (zero) to disable auto-scrolling and enable manual scrol

• Cisco DS-X9530-SF1-K9 - Supervisor-1 Module - Control Processor, CHAPTER Send documentation comments to [email protected]. 4-1 Cisco MDS 9000 Family Configuration Guide OL-6973-03, Cisco MDS SAN-OS Release 2.x 4 Initial Configuration This chapter describes how to initially configure switches so they can be accessed by other devices. This chapter includes the following sections: • Starting a Switch in the Cisco MDS 9000 Family, page 4-2 • Initial Setup Routine, page 4-2 • Accessing the Switch, page 4-14 • Assigning a Switch Name, page 4-15 • Where Do You Go Next?, page 4-15 • Verifying

• Send documentation comments to [email protected]. 6-37 Cisco MDS 9000 Family Configuration Guide OL-6973-03, Cisco MDS SAN-OS Release 2.x Chapter 6 Software Images Corrupted Bootflash Recovery Recovering One Supervisor Module With Corrupted Bootflash If one supervisor module has functioning bootflash and the other has corrupted bootflash, follow these

• Cisco DS-X9530-SF1-K9 - Supervisor-1 Module - Control Processor, Send documentation comments to [email protected]. 33-5 Cisco MDS 9000 Family Configuration Guide OL-6973-03, Cisco MDS SAN-OS Release 2.x Chapter 33 Configuring FCIP Basic FCIP Configuration To enable FCIP on any participating switch, follow these steps: Basic FCIP Configuration To configure an FCIP link, follow these steps on both switches: Step 1 Configure the Gigabit Ethernet interface. Step 2 Create an FCIP profile, and then assign the Gigabit Ethernet interface’s IP address to the profile. Step 3 Create an FCIP interface, and then assign the profile to the interface. Step 4 Configure the peer IP address for the FCIP interface. Step 5 Enable the i

• CHAPTER Send documentation comments to [email protected]. 22-1 Cisco MDS 9000 Family Configuration Guide OL-6973-03, Cisco MDS SAN-OS Release 2.x 22 Managing FLOGI, Name Server, FDMI, and RSCN Databases This chapter describes the fabric login database, the name server features, the Fabric-Device Management Interface, and Registered State Change Notification (RSCN) information provi

• Cisco DS-X9530-SF1-K9 - Supervisor-1 Module - Control Processor, Send documentation comments to [email protected]. 30-15 Cisco MDS 9000 Family Configuration Guide OL-6973-03, Cisco MDS SAN-OS Release 2.x Chapter 30 Configuring IPsec Network Security Configuring IPsec In Figure 30-3, an SA cannot be established in Case 4. This is because SAs are always requested according to the crypto ACLs at the initiating packet's end. In Case 4, router N requests that all traffic between Subnet X and Subnet Y be protected, but this is a superset of the specific flows permitted by the crypto ACL at switch M so the request is therefore not permitted. Case 3 works because switc

• Cisco DS-X9530-SF1-K9 - Supervisor-1 Module - Control Processor, Send documentation comments to [email protected]. 12-3 Cisco MDS 9000 Family Configuration Guide OL-6973-03, Cisco MDS SAN-OS Release 2.x Chapter 12 Configuring Trunking Trunk-Allowed VSAN Configuration Tip The preferred configuration on the Cisco MDS 9000 Family switches is one side of the trunk set to auto and the other set to on. Note When connected to a third-party switch, the trunk mode configuration has no effect—the ISL is always in a trunking disabled state. Configuring the Trunk Mode To configure the trunk mode, follow these steps: Trunk-Allowed VSAN Configuration E

• Cisco DS-X9530-SF1-K9 - Supervisor-1 Module - Control Processor, Send documentation comments to [email protected]. xlii Cisco MDS 9000 Family Configuration Guide OL-6973-03, Cisco MDS SAN-OS Release 2.x New and Changed Information SCSI flow services support for interfaces Allows the configuration of SCSI flow services on groups of four interfaces as well as the entire module. 2.1(2) Chapter 38, “Configuring SCSI Flow Services and Statistics” Special characters in TACACS+ global secret keys Allows the use of the dollar sign ($) and the percent sign (%) in TACACS+ secret global keys. 2.1(2) Chapter 28, “Configuring RADIUS and TACACS+” Control for SNMP notifications for linkUp/linkDown traps

• Cisco DS-X9530-SF1-K9 - Supervisor-1 Module - Control Processor, Send documentation comments to [email protected]. 20-9 Cisco MDS 9000 Family Configuration Guide OL-6973-03, Cisco MDS SAN-OS Release 2.x Chapter 20 Distributing Device Alias Services Device Alias Configuration Verification Example 20-18 Displays the Device Aliases in the Zone Set Information switch# show zoneset zoneset name s1 vsan 1 zone name z1 vsan 1 pwwn 21:01:00:e0:8b:2e:80:93 [x] <--------------- Device alias displayed for each pWWN. pwwn 21:00:00:20:37:39:ab:5f [y] zone name z2 vsan 1 pwwn 21:00:00:e0:8b:0b:66:56 [SampleName] pwwn 21:00:00:20:37:39:ac:0d [z] Example 20-19 Displays the the Device Al

• Send documentation comments to [email protected]. 14-11 Cisco MDS 9000 Family Configuration Guide OL-6973-03, Cisco MDS SAN-OS Release 2.x Chapter 14 Configuring Domain Parameters Persistent FC IDs Manual Configuration To configure persistent FC IDs, follow these steps: Unique Area FC IDs for Some HBAs Note Only read this section if the HBA port and

• Cisco DS-X9530-SF1-K9 - Supervisor-1 Module - Control Processor, Send documentation comments to [email protected]. 5-2 Cisco MDS 9000 Family Configuration Guide OL-6973-03, Cisco MDS SAN-OS Release 2.x Chapter 5 Using the CFS Infrastructure About CFS About CFS Many features in the Cisco MDS switches require configuration synchronization in all switches in the fabric. Maintaining configuration synchronization across a fabric is important to maintain fabric consistency. In the absence of a common infrastructure, such synchronization is achieved through manual configuration at each switch in the fabric. This process is tedious and error prone. Cisco Fabric Services (CFS) provides a common infrastructure for automatic configuration

• Cisco DS-X9530-SF1-K9 - Supervisor-1 Module - Control Processor, Send documentation comments to [email protected]. 8-8 Cisco MDS 9000 Family Configuration Guide OL-6973-03, Cisco MDS SAN-OS Release 2.x Chapter 8 Configuring High Availability Displaying HA Information

• Send documentation comments to [email protected]. 48-8 Cisco MDS 9000 Family Configuration Guide OL-6973-03, Cisco MDS SAN-OS Release 2.x Chapter 48 Configuring Port Tracking Default Settings Example 48-4 Displays a Forced Shut Configuration switch# show interface fc 1/5 fc1/5 is up Hardware is Fibre Channel, FCOT is short wave laser Port WWN is 20:05:00:

• Cisco DS-X9530-SF1-K9 - Supervisor-1 Module - Control Processor, Send documentation comments to [email protected]. 34-9 Cisco MDS 9000 Family Configuration Guide OL-6973-03, Cisco MDS SAN-OS Release 2.x Chapter 34 Configuring the SAN Extension Tuner Default Settings Example 34-4 Displays N ports Configured on a Specified Gigabit Ethernet Interface. switch# show san-ext-tuner interface gigabitethernet 3/1 ---------------------------------------------------------------------------- Interface NODE NAME PORT NAME VSAN ---------------------------------------------------------------------------- GigabitEthernet3/1 10:00:00:00:00:00:00:00 10:00:00:00:00:00:00:01 91 Example 34-5 Displays the Transfer R

• Cisco DS-X9530-SF1-K9 - Supervisor-1 Module - Control Processor, Send documentation comments to [email protected]. 24-48 Cisco MDS 9000 Family Configuration Guide OL-6973-03, Cisco MDS SAN-OS Release 2.x Chapter 24 Configuring FICON Displaying RLIR Information Example 24-32 Displays the LIR History switch# show rlir history Link incident history ---------------------------------------------------------------------------- *Host Time Stamp Switch Time Stamp Port Interface Link Incident ---------------------------------------------------------------------------- *Sun Nov 30 21:47:28 2003 Sun Nov 30 13:47:55 2003 2 fc1/2 Implicit Incide

• Cisco DS-X9530-SF1-K9 - Supervisor-1 Module - Control Processor, Send documentation comments to [email protected]. 11-25 Cisco MDS 9000 Family Configuration Guide OL-6973-03, Cisco MDS SAN-OS Release 2.x Chapter 11 Configuring Interfaces Displaying Interface Information sup-fc0 is up Hardware is Fibre Channel Speed is 1 Gbps 139597 packets input, 13852970 bytes 0 multicast frames, 0 compressed 0 input errors, 0 frame, 0 overrun 0 fifo 139516 packets output, 16759004 bytes, 0 underruns 0 output errors, 0 collisions, 0 fif

• Cisco DS-X9530-SF1-K9 - Supervisor-1 Module - Control Processor, Send documentation comments to [email protected]. 24-24 Cisco MDS 9000 Family Configuration Guide OL-6973-03, Cisco MDS SAN-OS Release 2.x Chapter 24 Configuring FICON FICON Configuration Files Applying the FICON Configuration Files You can apply the configuration from the saved files to the running configuration using the ficon vsan number apply file filename command. switch# ficon vsan 2 apply file SampleFile Editing FICON Configuration Files The configuration file submode allows you to create and edit FICON configuration files. If a specified file does not exist, it is created. Up to 16 files can be saved. Each file name is restricted

• Cisco DS-X9530-SF1-K9 - Supervisor-1 Module - Control Processor, Send documentation comments to [email protected]. Index IN-16 Cisco MDS 9000 Family Configuration Guide OL-6973-03, Cisco MDS SAN-OS Release 2.x kernel core dumps 50-8 configuring 50-9 kickstart images KICKSTART variable 6-1 loading system images 6-28 overview 6-2 recovering corrupted 6-34 recovery 6-35 recovery interruption 6-29 L last byte FC IDs 24-16 LEDs link 11-18 speed 11-18 status 11-18 libpcap freeware 49-4 licenses description 3-1 displaying information 3-12 enterprise package 3-3 extended BB_credits 11-15 Fabric Manager Server package 3-5 factory-installed 3-6 feature-based 3-3 grace period expiration 3-11 high availability 3-5 identifyi

• Cisco DS-X9530-SF1-K9 - Supervisor-1 Module - Control Processor, Send documentation comments to [email protected]. 11-10 Cisco MDS 9000 Family Configuration Guide OL-6973-03, Cisco MDS SAN-OS Release 2.x Chapter 11 Configuring Interfaces Fibre Channel Interfaces The Cisco SAN-OS software implicitly performs a graceful shut down in response to either of the following actions for interfaces operating in the E port mode: • If you shut down an interface • If a Cisco SAN-OS software application executes a port shut down as part of its function A graceful shut down ensure

• Cisco DS-X9530-SF1-K9 - Supervisor-1 Module - Control Processor, Send documentation comments to [email protected]. 36-2 Cisco MDS 9000 Family Configuration Guide OL-6973-03, Cisco MDS SAN-OS Release 2.x Chapter 36 Configuring IP Services Traffic Management Services Traffic Management Services In-band options are compliant with and use the RFC 2625 standards. An NMS host running IP protocol over a FC interface can access the switch using the IPFC functionality. If the NMS does not have a Fibre Channel HBA, in-band management can still be performed using one of the switches as an access point

• Cisco DS-X9530-SF1-K9 - Supervisor-1 Module - Control Processor, Send documentation comments to [email protected]. 26-3 Cisco MDS 9000 Family Configuration Guide OL-6973-03, Cisco MDS SAN-OS Release 2.x Chapter 26 Configuring Users and Common Roles Role-Based Authorization In Step 3, rule 1 is applied first, thus permitting sangroup users access to all config commands. Rule 2 is applied next, denying FSPF configuration to sangroup users. As a result, sangroup users can perform all other config commands, except fspf configuration commands. Note The order of rule placement is important. If you had swapped these two rules and issued the deny config feature fspf rule first and issued the permit config rule next, you would be allo

• Cisco DS-X9530-SF1-K9 - Supervisor-1 Module - Control Processor, Send documentation comments to [email protected]. 50-13 Cisco MDS 9000 Family Configuration Guide OL-6973-03, Cisco MDS SAN-OS Release 2.x Chapter 50 Monitoring System Processes and Logs Online System Health Management • User-driven test for external connectivity verification, port is shutdown during the test (FC ports only). • User-driven test for internal connectivity verification (Fibre Channel and iSCSI ports). To perform the required test on a specific module, follow these steps: Clearing Previous Error Reports You can clear the error history for Fibre C

• Cisco DS-X9530-SF1-K9 - Supervisor-1 Module - Control Processor, Send documentation comments to [email protected]. 50-10 Cisco MDS 9000 Family Configuration Guide OL-6973-03, Cisco MDS SAN-OS Release 2.x Chapter 50 Monitoring System Processes and Logs Online System Health Management Online System Health Management The Online Health Management System (system health) is a hardware fault detection and recovery feature. It ensures the general health of switching, services, and supervisor modules in any switch in the Cisco MDS 9000 Family. The system health application runs on all Cisco MDS modules and monitors system hardware in a given MDS switch. The system health application running i

Related Products and Documents (Processor):

Comparable Devices:

Similar Resources:

• Motorola MC68302 (480 pages)  1995 Motorola, Inc. All Rights Reserved MC68302 Integrated Multiprotocol ProcessorUser’s Manual Microprocessors and MemoryTechnologies Group Literature Distribution Centers:USA/EUROPE: Motorola Literature Distribution; P.O. Box 20912, Arizona 85036.JAPAN: Nippon Motorola Ltd.; 4-32-1, Nishi-Gotanda, Shinagawa-ku, Tokyo 141 Japan.ASIA-PAC …

• TL Audio VP-1 (23 pages) CONTENTS 1 INTRODUCTION 2 PRECAUTIONS 3 INSTALLATION 3.1 AC Mains Supply 3.2 Audio Inputs 3.3 Unbalanced Line Inputs 3.4 Instrument Inputs 3.5 Insertion Points 3.6 Balanced Outputs 3.7 Unbalanced Output 3.8 Ventilation 4 OPERATION 4.1 Input Select 4.2 Input Gain 4.3 High Pass Filter 4.4 Phase Reverse 4.5 Pad 4.6 Phantom Power 4.7 Drive and Peak LE …

• Lexicon MPX 500 - RELEASE NOTES REV 1 (2 pages) NEW SYSTEM MODE PARAMETERR1-MPX 1 Mode has been added to the system parameter MIDI Program Change. This additional settingenables the MPX 500 to respond to program change messages from a Lexicon MPX R1 Foot Controllerset to MPX 1 Mode.Parameter Settings Default SettingMIDI Program Change Enabled, Disabled, R1-MPX1 Mode EnabledOVL INDICATOR SIGNALS DSP O …

• Key Digital Chroma KD-HDMI2X4P (30 pages) 2006-2007 Product CatalogKey Digital™ Systems :: 521 East 3rd Street :: Mount Vernon, NY 10553Phone :: 914.667.9700 Fax :: 914.668.8666 Web :: www.keydigital.com …

• HP L5006tm (5 pages) 1.2.3.4.5. PowerPowerPowerPower: Turns the unit on and off.SelectSelectSelectSelect: Selects the adjustment items from the on-screen display (OSD) menus.Arrow downArrow downArrow downArrow down: Enter brightness adjustment, decrease value of the adjustment item, select item counter-clockwise.Arrow upArrow upArrow upArrow up: Enter contrast of the OSD, incr …

• Boss WP-20G (24 pages) Thank you, and congratulations on your choice of BOSS WP-20G GK Effect. Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY”and “IMPORTANT NOTES” (p. 18; p. 21). These sections provide important information concerning the proper operation of the unit.Additionally, in order to feel assured that you have gained a good …

Comments, Questions and Opinions: