Manualios.com

Cisco NPE-G2 - Network Processing Engine G2 Installation And Configuration Information

  • NPE-G2 - Network Processing Engine G2 Processor
  • ma2n4A5FYW566
  • Installation And Configuration Information
  • PDF / Adobe Acrobat Reader
  • 68

Cisco NPE-G2 - Network Processing Engine G2 Manual Online:

3.05, 1415 votes
Cisco NPE-G2 - Network Processing Engine G2 User Manual
Cisco NPE-G2 - Network Processing Engine G2 User Guide
Cisco NPE-G2 - Network Processing Engine G2 Online Manual

Text of Cisco NPE-G2 - Network Processing Engine G2 User Guide:

  • Cisco NPE-G2 - Network Processing Engine G2, 7-4 Network Processing Engine and Network Services Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 Installation and Configuration Information Copying the Configuration File Copying the Configuration File Caution Before powering down the router to install the NPE-G1 or NPE-G2, you must save the current configuration to a Flash Disk, PC Card, Trivial File Transfer Protocol (TFTP) file server, or PC before you install the NPE-G1 or NPE-G2, or the configuration will be lost and you will have to manually re-enter your configuration. Cisco IOS looks to the NPE-

  • Cisco NPE-G2 - Network Processing Engine G2, 7-20 Network Processing Engine and Network Services Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 Installation and Configuration Information Installing the NPE-G1 or NPE-G2 Caution Do not remove a USB Flash memory module when a read or write operation to the USB Flash memory module is in progress. The router might reload, or the USB Flash memory module can be damaged. Note Only Cisco USB Flash memory modules and the Aladdin USB eToken Pro key are supported by Cisco routers. Figure 7-8 Connecting a USB Flash Memory Module to a Router U

  • Cisco NPE-G2 - Network Processing Engine G2, 7-31 Network Processing Engine and Network Services Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 Installation and Configuration Information Installing the NPE-G1 or NPE-G2 Step 1 Loosen the left and right captive installation screws on the NPE-G1 or NPE-G2. Step 2 Hold the cable-management bracket so that it is positioned above the NPE-G1 or NPE-G2 captive installation screws as shown in Figure 7-17 and Figure 7-18. The bracket is properly positioned when the horizontally-faced notch is at the left, the vertically-faced notch is at the right, and the bracket’s outer edge is flush wi

  • Cisco NPE-G2 - Network Processing Engine G2, 7-39 Network Processing Engine and Network Services Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 Installation and Configuration Information Installing the NPE-G1 or NPE-G2 Warning Before completing any of the following steps, and to prevent short-circuit or shock hazards, ensure that power is removed from the DC circuit. To ensure that all power is OFF, locate the circuit breaker on the panel board that services the DC circuit, switch the circuit breaker to the OFF position, and tape the switch handle of the circuit breaker in the OFF position. Statement 322 Warning When installing the unit, the ground connec

  • Cisco NPE-G2 - Network Processing Engine G2, 7-14 Network Processing Engine and Network Services Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 Installation and Configuration Information Removing the Network Processing Engine Figure 7-4 Removing the Strain-Relief Cover from a Cisco uBR7246VXR Router DC-Input Power Supply Step 4 Using a 3/16-inch flat-blade screwdriver, loosen the screw below the +V lead receptacle and pull the lead from the connector. Repeat this step for the –V lead only. See Figure 7-5. 1 Power switch 6 –V lead 2 Power receptacle 7 +V lead 3 Captive screw 8 Strain-relief cover 4 M5 grounding receptacles 9 M4 nuts and studs 5 M5 grounding lug 66408 3 5 7

  • Cisco NPE-G2 - Network Processing Engine G2, 7-65 Network Processing Engine and Network Services Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 Installation and Configuration Information Troubleshooting the Upgrade Running new upgrade for first time System Bootstrap, Version 12.2(20031011:151758) [biff] Copyright (c) 1994-2003 by cisco Systems, Inc. ROM:Rebooted by watchdog hard reset C7200 platform with 1048576 Kbytes of main memory Upgrade ROMMON initialized rommon 1 > Note It is advisable to load a known good Cisco IOS i

  • Cisco NPE-G2 - Network Processing Engine G2, 7-26 Network Processing Engine and Network Services Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 Installation and Configuration Information Installing the NPE-G1 or NPE-G2 Upgrading the SDRAM SODIMMs on the NPE-G1 (Optional) If you have purchased an SDRAM memory upgrade for the NPE-G1, replace the SDRAM SODIMMs on the NPE-G1 using the following instructions. Removing a SODIMM Step 1 Locate the SODIMMs on the NPE-G1. Figure 7-14 Locating the SODIMMs on the NPE-G1 Note Both SODIMMs must be of the same size and type, and both SODIMM sockets must be populated. Step 2 Remove the SODIMM you want to replace by pulling outward

  • 7-50 Network Processing Engine and Network Services Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 Installation and Configuration Information Enabling the Second Processor on the NPE-G1 CPU% per hour (last 72 hours) * = maximum CPU% # = average CPU% Using the show mpf interface Command Using the show mpf interface command without argu

  • 7-21 Network Processing Engine and Network Services Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 Installation and Configuration Information Installing the NPE-G1 or NPE-G2 Figure 7-9 Types of SFP Module Latches Note The SFP module must be installed before you connect the cables to it. The SPF module has three types of latches, whic

  • Cisco NPE-G2 - Network Processing Engine G2, 7-23 Network Processing Engine and Network Services Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 Installation and Configuration Information Installing the NPE-G1 or NPE-G2 Installing a GBIC—NPE-G1 Use the instructions in this section to install a GBIC in the NPE-G1. Figure 7-11 Installing a GBIC in the NPE-G1 Step 1 Turn the GBIC so the label side is up and the alignment groove is down. Note The GBIC is keyed so that it cannot be inserted incorrectly. Step 2 Insert the GBIC into GBIC port 0/1, 0/2, or 0/3. Repeat this step if you are installing more than one GBIC. Note Do not remove the GBIC plugs until you are r

  • Cisco NPE-G2 - Network Processing Engine G2, 7-46 Network Processing Engine and Network Services Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 Installation and Configuration Information Enabling the Second Processor on the NPE-G1 Note When powering on the router, wait a minimum of 30 seconds before powering it off again. Step 3 Listen for the fans; you should immediately hear them operating. Step 4 During the boot process, observe the system LEDs. The LEDs on most of the port adapters go on and off in an irregular sequence. Some may go on, go off, and go on again for a short time. On the NPE-G1 or NPE-G2 and the I/O controller, the POWER OK LED goes on

  • Cisco NPE-G2 - Network Processing Engine G2, 7-64 Network Processing Engine and Network Services Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 Installation and Configuration Information Upgrading ROMmon on the NPE-G1 or NPE-G2 Using the show rom-monitor Command and ROMmon CLI showmon Commands Use the show rom-monitor command if you are in Cisco IOS, or the ROMmon CLI showmon command if you are in ROMmon, to determine which ROMmon images are available. See the following examples for information shown in the output of the show rom-m

  • Cisco NPE-G2 - Network Processing Engine G2, 7-51 Network Processing Engine and Network Services Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 Installation and Configuration Information Enabling the Second Processor on the NPE-G1 Gi0/1.201 201 up RX punts 29 Gi0/1.202 202 up Gi0/1.206 206 up Gi0/1.2002 602 up RX punts 26142 Gi0/1.2004 604 up Using the show mpf interface GigabitEthernet 0/1 100 Command The following example displays the interface information for VLAN number 100 on the GigabitEthernet 0/

  • Cisco NPE-G2 - Network Processing Engine G2, 7-68 Network Processing Engine and Network Services Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 Installation and Configuration Information Fiber Optic Cleaning Information

  • Cisco NPE-G2 - Network Processing Engine G2, 7-13 Network Processing Engine and Network Services Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 Installation and Configuration Information Removing the Network Processing Engine Step 5 Repeat this step for the –V lead and the ground lead. Note The color coding of the DC-input power supply leads depends on the color coding of the DC power source at your site. Typically, green or green and yellow are used for ground. Make certain that the lead color coding you choose for the

  • Cisco NPE-G2 - Network Processing Engine G2, 7-54 Network Processing Engine and Network Services Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 Installation and Configuration Information Copying the Saved Configuration to NVRAM Downloading the Saved Configuration from the TFTP Server After you install the NPE-G1 or NPE-G2 in the router and verify a successful router boot, you must retrieve the router configuration from the TFTP server and copy it to NVRAM. Use the copy tftp running-config command to copy the saved configuration f

  • 7-19 Network Processing Engine and Network Services Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 Installation and Configuration Information Installing the NPE-G1 or NPE-G2 Installing a CompactFlash Disk Use the following instructions to install the CompactFlash Disk. Figure 7-7 Installing a CompactFlash Disk Step 1 Turn

  • Cisco NPE-G2 - Network Processing Engine G2, 7-37 Network Processing Engine and Network Services Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 Installation and Configuration Information Installing the NPE-G1 or NPE-G2 Reconnecting AC-Input Power to the Cisco uBR7246VXR Router Figure 7-25 Connecting AC-Input Power to a Cisco uBR7246VXR Router To reconnect AC-input power to a Cisco uBR7246VXR router, complete the following steps: Step 1 At the rear of the router, check that the power switch on the power supply is in the off (O) position. Step 2 Slide the cable-retention cli

  • Cisco NPE-G2 - Network Processing Engine G2, 7-16 Network Processing Engine and Network Services Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 Installation and Configuration Information Removing the Network Processing Engine Removing the NPE or NSE-1 To remove the NPE or NSE-1 from a Cisco 7200 VXR router, a Cisco uBR7246VXR or a Cisco UBR7225VXR router complete the following steps. Note The weight of installed power supplies in your Cisco 7200 VXR or Cisco uBR7246VXR router might make it difficult to remove the network processing engine. If you have difficulty, first remove the power supplies from the chassis, and then remove the network processing engine. See the “Removing and R

  • Cisco NPE-G2 - Network Processing Engine G2, 7-44 Network Processing Engine and Network Services Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 Installation and Configuration Information Installing the NPE-G1 or NPE-G2 Figure 7-31 Replacing the Strain-Relief Cover on a Cisco uBR7246VXR Series DC-Input Power Supply Step 9 Restore current to the –V and +V leads. Note For the Cisco uBR7200 series routers, each DC-input power supply rating is 14A, 700 volt ampere (VA). This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that a listed and certified fuse or circuit breaker, 35A minimum 60 VDC, is used on all current-ca

  • Cisco NPE-G2 - Network Processing Engine G2, 7-9 Network Processing Engine and Network Services Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 Installation and Configuration Information Removing the Network Processing Engine Note When powering off the router, wait a minimum of 30 seconds before powering it on again. Step 2 Observe the following items: • The green OK LED on the power supply turns off. • The fans stop operating. • The LEDs on the I/O controller turn off. • The LEDs on the port adapters turn off. Caution When the power switch on a Cisco uBR7200 series power supply is turned to the off (O) position, the power supply enters a reset cycle for 90 secon

Related Products and Documents (Processor):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Thermador T42BD820NS Installation instructions manual thermador/t42bd820ns-16G.pdf 18 Dec 2022 48 1.56 Mb
2 Dell UltraSharp 2005FPW Setting up dell/ultrasharp-2005fpw-CV6.pdf 11 May 2023 2 22.02 Mb
3 Sony VPL-VW11HT - Lcd Video Projector Dimensions sony/vpl-vw11ht-lcd-video-projector-78W.pdf 14 Jan 2023 1 0.02 Mb
4 ARX 8-pre Owner's manual arx/8-pre-X87.pdf 08 Dec 2022 4 0.29 Mb
5 Radio Shack 43-484 Owner's manual radio-shack/43-484-6A4.pdf 28 May 2023 12 0.39 Mb
6 Kenmore 625.349223 Manual  kenmore/625-349223-19R.pdf 26 Mar 2023 32

Similar Resources:

  • IBM

    R30

    (9 pages)
    Part Number: 46P6590Setup GuideThinkPadR30 SeriesThank you for purchasing the IBM ThinkPad R30 Series computer. Match the items on this list with the items in the box.If any item is missing or damaged, please contact your place of purchase.h Computer h Battery packNotes:1. Some models may contain additionalitems that are not listed.2. Your computer features …
  • Compaq

    108164-003 - ProLiant - 800

    (17 pages)
    INTEGRATION NOTE1................................................................................................................................................................ECG043/1097October, 1997Prepared ByNovell IntegrationBusiness Unit, CompaqComputer CorporationCONTENTSExecutive Summary ........ 3Introduction ................... 4PCNTNW.LANCustom St …
  • ASROCK

    X58 EXTREME6 -

    (293 pages)
    11111ASRock X58 Extreme6 MotherboardEnglishEnglishEnglishEnglishEnglishCopyright Notice:Copyright Notice:Copyright Notice:Copyright Notice:Copyright Notice:No part of this installation guide may be reproduced, transcribed, transmitted, or trans-lated in any language, in any form or by any means, except duplication of documen-tation by the purchaser for bac …
  • Stewart Audio

    DSP 4x4

    (12 pages)
    Owner’s Manual DSP 4x4 www.stewartaudio.com July 2014 DSP 4x4USB POWEROUTPUT 1 OUTPUT 2 OUTPUT 3 OUTPUT 4 INPUT 1 INPUT 2 INPUT 3 INPUT 4POWER5V1234PHANTOMPOWERRS232TXRX- + - + - + - + - + - + - + - + …
  • Dell

    D620 - Latitude Laptop Computer System Core Duo Processor Wireless XP Pro

    (145 pages)
    DCSE Version Materials Global Log OutBACK TO: Dell Certified Systems Expert Previous PrintThis document contains information about the Latitude™ D620. The Latitude D620 training course goal is to prepare you to accurately and effectively resolve customer inquiries and technical issues and to inform you of the proper steps for replacing hardware. This cours …
  • YORKVILLE

    UNITY UP15

    (14 pages)
    YorkvilleUP15P R OF E S S IO N A L B A L A NC E D SO U N D P R O C ES S I N G S Y S TE MPO WERCL IP A CL IP BYorkvilleUP215P R OF E S S IO N A L B A L A NC E D SO U N D P R O C ES S I N G S Y S TE MPO WERCL IP A CL IP BYorkvillePROCESSORSOWNER'S MANUALMANUAL de L'UTILISATEURP R O F E S S I O N A L B A L A N C E D S O U N D P R O C …

Comments, Questions and Opinions: