Manualios.com

Cisco VC220 Quick Start Manual

Cisco VC220 Manual Online:

3, 815 votes
Cisco VC220 User Manual
Cisco VC220 User Guide
Cisco VC220 Online Manual

Text of Cisco VC220 User Guide:

  • Quick Start Guide Cisco Small Business VC 220 Dome WDR Day/Night PoE Network Camera Package Contents • Cisco VC 220 Network Camera • Power Adapter • Two L-Shaped Audio Cables • Mounting and Installation Accessories including a TORX ™ screwdriver • I/O Connector • Setup and Documentation CD — includes localized Quick Start Guides in French, German, Italian, and Span

  • Cisco VC220, 2 VC 220 Dome WDR Day/Night PoE Network Camera Quick Start Guide Welcome Thank you for choosing the Cisco VC 220 Dome Wide Dynamic Range (WDR) Day/Night PoE Network Camera. The Cisco VC 220 network camera is a high-performance web-ready camera, and can be part of a flexible surveillance system. This guide describes how to physically install your Cisco VC 220 network camera and how to install and launch the provided Setup Wizard.

  • Cisco VC220, VC 220 Dome WDR Day/Night PoE Network Camera Quick Start Guide 3 Before You Begin Before you begin the installation, make sure that you have the following equipment and services: • At least one computer running Microsoft Internet Explorer 6.x, or later (other browsers can be used but may have limited functionality) • An active LAN IP connection After the basic hardware installation, Cisco strongly recommends that you run the Setup Wizard on the CD-ROM for first-time software installation of the camera. Advanced users can set up the Cisco VC 220 directly from the web i

  • Cisco VC220, 4 VC 220 Dome WDR Day/Night PoE Network Camera Quick Start Guide Product Overview Descriptive Diagrams The following illustrations show the major components of the camera. Lens and Tilt Screws Allows you to make pan/tilt 3-axis adjustments. For wall or ceiling mounting on an unlevel plane, you can rotate the 3rd axis to straighten the view. See “Adjusting the Lens” section on page 12. Built-in Microphone Features a built-in microphone mounted on the front of the camera. The camera also has a connection for an external microphone on the r

  • Cisco VC220, VC 220 Dome WDR Day/Night PoE Network Camera Quick Start Guide 5 Light Sensor Detects the amount of ambient light and switches the camera from day to night. If light is too low, the light sensor triggers the IR LEDs to turn on. 12 Infrared (IR) LEDs Enables operation in complete darkness. The ring of IR LEDs are built-in with a working range of 15 m (50 feet). Status LED Indicates the following status: LED Off—The power is off or the LED status is turned off. Flashing green in one second intervals

  • Cisco VC220, 6 VC 220 Dome WDR Day/Night PoE Network Camera Quick Start Guide Focus and Zoom Controllers Adjusts the focus and zoom of your camera. See “Adjusting the Lens” on page 12. Image and Pan Adjustment Screws Allows you to make pan/tilt 3-axis adjustments. For wall or ceiling mounting on an unlevel plane, you can rotate the 3rd axis to straighten the view. See “Adjusting the Lens” on page 12. GPIO (General Purpose I/O Terminal Block) Allows you to connect the camera to external input/ output devices that can provide additional controlling functions. For more information, see the Cisco VC 220 Network Camera Administration Guide found at: http://www.cisco.com/en/US/products/ps9

  • Cisco VC220, VC 220 Dome WDR Day/Night PoE Network Camera Quick Start Guide 7 Installing Your Cisco VC 220 Camera Installation Tips Before installing the camera, look for a spot that best suits your needs. The built-in PIR sensor is designed to be triggered when a person enters its detection range. Therefore, it is crucial to install your camera with the PIR sensor facing the desired direction. The sensitivity of the PIR sensor depends on the object size and temperature differences between the object and the background environment. CAUTION Do not install the Cisco VC 220 camera

  • Cisco VC220, 8 VC 220 Dome WDR Day/Night PoE Network Camera Quick Start Guide Mounting Your Cisco VC 220 Camera If you have more than one camera, make a note of the MAC address found on the side of your camera. You may want to refer to the MAC address later to identify multiple cameras. Your MAC address will be something like the following: 00:21:29:72:7D:2C. STEP 1 Use the screwdriver to detach the dome cover from the camera base. STEP 2 For a ceiling mount, insert the supplied two screws in the corresponding holes on each side of the camera ba

  • Cisco VC220, VC 220 Dome WDR Day/Night PoE Network Camera Quick Start Guide 9 Connecting the Equipment There are two options for deploying the Cisco VC 220 camera on the network, a basic Ethernet setup and a Power over Ethernet (PoE) setup. The basic setup is described in this document. For PoE setups, see the Cisco VC 220 Network Camera Administration Guide found at: http://www.cisco.com/en/US/products/ps9944/ prod_maintenance_guides_list.html. 4

  • 10 VC 220 Dome WDR Day/Night PoE Network Camera Quick Start Guide Basic Ethernet Setup Follow these steps to perform a basic Ethernet setup. STEP 1 Connect any external devices to the general I/O terminal block, if you have sensors and alarms (1). STEP 2 Connect your Cisco VC 220 camera to a router or a switch using an Ethernet cable (2). STEP 3 Connect the

  • Cisco VC220, VC 220 Dome WDR Day/Night PoE Network Camera Quick Start Guide 11 Verifying the Hardware Installation After you install your Cisco VC 220 camera, check the Status LED to verify connectivity. See “Status LED” on page 5. NOTE It is suggested that you install the software – see “Getting Started with the Configuration” on page 11 – before you replace the dome cover on the camera. This is because after the software is installed, you will be able to use the web-based configuration utility to see how the lens

  • 12 VC 220 Dome WDR Day/Night PoE Network Camera Quick Start Guide Suggested Next Steps Adjusting the Lens After viewing the live image on the web-based configuration utility, adjust the camera lens, zoom factor, and focus range as needed. NOTE Do not over rotate the camera lens. Doing so will damage the lens. To adjust the viewing angle: STEP 1 Loosen the pan screw and turn the lens

  • Cisco VC220, VC 220 Dome WDR Day/Night PoE Network Camera Quick Start Guide 13 S TEP 5 Loosen the focus controller to adjust the focus range from Near to Infinity. Upon completion, tighten the focus controller. Attaching the Dome Cover The supplied screwdriver is exclusively designed to match the dome screws. In case you need to adjust the camera at a later time, do not discard the screwdriver. STEP 1 Route all the cables through the base channel under the camera. TIP Use the two L-shaped audio cables when you route the cables to prevent having to remove a tab. STEP 2 (Optional) Remove the tab (or tabs) from the dome cover to accommodate the cables. To avoid injury, plac

  • Cisco VC220, 14 VC 220 Dome WDR Day/Night PoE Network Camera Quick Start Guide S TEP 4 Secure the two dome screws with a screwdriver. STEP 5 Ensure all parts of your Cisco VC 220 camera are securely installed. You are now ready to start using your Cisco VC 220 camera.

  • Cisco VC220, VC 220 Dome WDR Day/Night PoE Network Camera Quick Start Guide 15 Where to Go From Here Support Cisco Small Business Support Community www.cisco.com/go/smallbizsupport Product Information (Including Software Updates) www.cisco.com/go/surveillance www.cisco.com/go/vc220 Phone Support Contacts www.cisco.com/en/US/support/tsd_cisco_small_ business_support_center_contacts.html Software Downloads (Login Required) Go to tools.cisco.com/support/downloads, and enter the model number in the Software Search box. Online Technical Support and Docume

  • Cisco VC220, Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.com http://www.cisco.com/smallbusiness Cisco, Cisco Systems, the Cisco logo, and the Cisco Systems logo are registered trademarks or trademarks of Cisco and/or its affiliates in the United States and certain other countries. All other trademarks mentioned in this document or website are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1002R) © 2010 Cisco Systems, Inc. All rights reserved. 78

Related Products and Documents (Security Camera):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 DYNATEK DFS9-1P Manual  dynatek/dfs9-1p-PVI.pdf 17 May 2023 4 0.43 Mb
2 KitchenAid KES2102 Instructions manual kitchenaid/kes2102-P16.pdf 14 May 2023 32
3 3Com SuperStack 4 3C16465B Operation & user’s manual 3com/superstack-4-3c16465b-QT5.pdf 29 Dec 2023 8 1.58 Mb
4 Coby MP-CD450 Operation & user’s manual coby/mp-cd450-U98.pdf 12 Jan 2023 5 1.93 Mb
5 Fanimation WindPointe FP7300 Owner's manual fanimation/windpointe-fp7300-X76.pdf 23 Aug 2023 14 1.03 Mb
6 Visonic KF-235PG2 Operation & user’s manual visonic/kf-235pg2-969.pdf 14 Oct 2022 4

Similar Resources:

  • SECO-LARM

    Enforcer Video Elite Series

    (2 pages)
    1.949.261.2999 (CA & Int’l) 1.800.662.0800 Fax: 1.949.261.7326Email: [email protected] Website: www.seco-larm.com 16842 Millikan Avenue, Irvine, CA 92606 The SECO-LARM policy is one of continual development. For that reason, SECO-LARM reserves the right to change prices and specifications without notice. SECO-LARM is not respons …
  • LevelOne

    FCS-0031

    (3 pages)
    2Megapixel PIR Lighting PoE Network CameraFCS-0031H/W Version: 1The LevelOne FCS-0031 is designed for 24hrs home surveillance. It provides a distinct and stylish design, with excellent features and quality, providing multiple applications and a wide range of coverage. Users can view the live motion image anywhere through a web browser via the Internet. With …
  • Toshiba

    IK-WB02A - PoE Network Camera

    (2 pages)
    IK-WB02AIP NETWORK CAMERA• Up to 30 FPS at 320 x 240, 22 FPS at 640 x 480 resolution• Choose from 3 power options - PoE (802.3af), 24 V AC and 12 VDC to best suit the application’s available power sources• PoE can save on installation costs by eliminating the need toinstall electrical wiring or power outlets• Motion detection built in• 2-Way …
  • ZKTeco

    MD532

    (17 pages)
    重要申明 1 Megapixel IP Camera with 4CH NVR Kit About This Manual All functions depend on the actual product. Since the product is subject to updating, our company is not responsible for any difference from this guide and not liable for any dispute over different technical parameters from this guide. The project is subject to any change wi …
  • Moog Videolarm

    PFD75C2N

    (32 pages)
    - 1 -Before attempting to connect or operate this product,please read these instructions completely. Product InstructionsIP Ready™ Series - Pressurized FusionDome™PFD75C2N & PFD75T2N81-IN535306/05/06 …
  • Clinton Electronics

    CE-T100HD

    (2 pages)
    With the supplied 2mm Allen Wrench, loosen the two set screws located near the base, on the outer camera housing. Remove mounting plate from the camera housing.1. DISASSEMBLE CAMERAAttach the mounting plate to the desired surface with the three provided 3x13mm Phillips head screws. Drill a 3/4” hole in the opening of the mounting plate if running the cable …

Comments, Questions and Opinions: