Cisco WS-C1924-A - Catalyst 1900 24 Ports 10MB Switch Hardware Installation Manual

Text of Cisco WS-C1924-A - Catalyst 1900 24 Ports 10MB Switch User Guide:

• Cisco WS-C1924-A - Catalyst 1900 24 Ports 10MB Switch, 3-5 Cisco 1900 Series Hardware Installation OL-19084-01 Chapter 3 Cable Information and Specifications for Cisco 1900 Series Routers Preparing to Connect to a Network the shielded serial transition cable has a DB-60 connector, which connects to the DB-60 port on a serial WIC. The other end of the serial transition cable is available with a connector appropriate for the standard that you specify. The synchronous serial port can be configured as DTE or DCE, depending on the attached cable (except EIA-530, which is DTE only). To order a shi

• 4-16 Cisco 1900 Series Hardware Installation OL-19084-02 Chapter 4 Installing and Connecting the Router Connecting to a Console Terminal or Modem Step 2 Connect the end of the cable with the DB-9 connector (or USB Type-A) to the terminal or PC. If your terminal or PC has a console port that does not accommodate a DB-9 connector, you must provide an appro

• Cisco WS-C1924-A - Catalyst 1900 24 Ports 10MB Switch, 4-22 Cisco 1900 Series Hardware Installation OL-19084-02 Chapter 4 Installing and Connecting the Router Connecting Power Warning This product relies on the building’s installation for short-circuit (over current) protection. Ensure that the protective device is rated not greater than: 15A, 120VAC (10A, 240VAC). Statement 1005 Connecting to DC Power If your router has a DC-input power supply, follow the directions in this section for proper wiring. A router with a DC-input power supply has a terminal block for the DC power connections. • DC Wiring Requirements for Cisco 1900 Series Routers, page 4-22 • Cisco 1900 Series Router

• 5-10 Cisco 1900 Series Hardware Installation OL-19084-02 Chapter 5 Configuring the Router Performing the Initial Configuration on the Router DETAILED STEPS Configuring the Console Idle Privileged EXEC Timeout This section describes how to configure the console line’s idle privileged EXEC timeout. By default, the privileged EXEC command interpreter waits 10 minutes to detect user inp

• Cisco WS-C1924-A - Catalyst 1900 24 Ports 10MB Switch, 1-13 Cisco 1900 Series Hardware Installation OL-19084-02 Chapter 1 Overview of the Router Interface Numbering The wireless access point does not have an external console port for connections. To configure the wireless device, you must use a console cable to connect a PC to the host router’s console port as described in Chapter 3, “Cable Information and Specifications for Cisco 1900 Series Routers,” and then use the Cisco IOS command-line interface (CLI) to access the interface. Table 1-5 describes the

• Cisco WS-C1924-A - Catalyst 1900 24 Ports 10MB Switch, xv Cisco 1900 Series Hardware Installation OL-19084-02 Preface Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning. Statement 1038 Related Documentation The Cisco IOS software that runs your Cisco 1940 series router includes extensive features and functionality. For information that is beyond the scope of this document, or for additional information, use the following resources. Timesaver Make sure that you have access to the documents listed below. Some of these documents are available in print, and all are on the Internet. I

• Cisco WS-C1924-A - Catalyst 1900 24 Ports 10MB Switch, 5-11 Cisco 1900 Series Hardware Installation OL-19084-02 Chapter 5 Configuring the Router Performing the Initial Configuration on the Router SUMMARY STEPS 1. enable 2. configure terminal 3. line console 0 4. exec-timeout minutes [seconds] 5. end 6. show running-config DETAILED STEPS Examples The following example shows how to set the console idle privileged EXEC timeout to 2 minutes 30 seconds: Command or Action Purpose Step 1 enable Example: Router> enable Enables privileged EXEC mode. • Enter your password if prompted. Step 2 config

• Cisco WS-C1924-A - Catalyst 1900 24 Ports 10MB Switch, 4-10 Cisco 1900 Series Hardware Installation OL-19084-02 Chapter 4 Installing and Connecting the Router Installing the Chassis Ground Connection To install the ground connection for a Cisco 1900 series router, follow these steps. Procedure Step 1 Strip one end of the ground wire to expose approximately 0.75 in. (20 mm) of conductor. Step 2 Crimp the 14 AWG green ground wire to a UL Listed/CSA certified ring terminal that is suitably sized for the number 6 ground screw provided on the rear panel of the router. The crimping tool should be one that is recommended by the ring lug terminal manufacturer. Step 3 Attach the ring terminal to the chassis. The attachment points are shown in

• Cisco WS-C1924-A - Catalyst 1900 24 Ports 10MB Switch, ix Cisco 1900 Series Hardware Installation OL-19084-02 Preface Tip Means the following information will help you solve a problem. Caution Means reader be careful. In this situation, you might perform an action that could result in equipment damage or loss of data. Timesaver Means the described action saves time. You can save time by performing the action described in the paragraph. Warning IMPORTANT SAFETY INSTRUCTIONS This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Use

• Cisco WS-C1924-A - Catalyst 1900 24 Ports 10MB Switch, 5-18 Cisco 1900 Series Hardware Installation OL-19084-02 Chapter 5 Configuring the Router Performing the Initial Configuration on the Router Example The following example shows how to configure virtual terminal lines with a password: ! line vty 0 4 password guessagain login ! What to Do Next After you configure the vty lines, follow these steps: • (Optional) To encrypt the virtual terminal line password, see the “Configuring Passwords and Privileges” chapter in the Cisco IOS Security Configuration Guide. Also see the Cisco IOS Password Encryption Facts tech note. • (Optional) To secure the VTY lines with an access li

• Cisco WS-C1924-A - Catalyst 1900 24 Ports 10MB Switch, CHAPTER 1-1 Cisco 1900 Series Hardware Installation OL-19084-02 1 Overview of the Router The Cisco 1900 Series Integrated Services Routers (ISRs) are modular routers with LAN and WAN connections that can be configured by means of interchangeable interface cards and internal service modules (ISMs). The series currently consists of the 1905, 1921, 1941, and 1941W (wireless) models. The 1941W is Wi-Fi CERTIFIED™ and 802.11a/b/g/n-compliant. The modular design of the routers provides flexibility, allowing you to configure your r

• Cisco WS-C1924-A - Catalyst 1900 24 Ports 10MB Switch, 2-7 Cisco 1900 Series Hardware Installation OL-19084-02 Chapter 2 Preparing for Router Installation Required Tools and Equipment for Installation and Maintenance Required Tools and Equipment for Installation and Maintenance You need the following tools and equipment for installing and upgrading the router and its components: • ESD-preventive cord and wrist strap • Number 2 Phillips screwdriver for installing or removing modules, and a flat-blade screwdriver for removing Compact Flash cover, upgrading memory, or other components: small, 3/16-inch (0.48 centim

• 5-15 Cisco 1900 Series Hardware Installation OL-19084-02 Chapter 5 Configuring the Router Performing the Initial Configuration on the Router Gateway of Last Resort When default information is being passed along through a dynamic routing protocol, no further configuration is required. The system periodically scans its routing table to choose the optimal defaul

• Cisco WS-C1924-A - Catalyst 1900 24 Ports 10MB Switch, 2-3 Cisco 1900 Series Hardware Installation OL-19084-02 Chapter 2 Preparing for Router Installation General Site Requirements • If an electrical accident occurs, proceed as follows: – Use caution; do not become a victim yourself. – Turn off power to the device. – If possible, send another person to get medical aid. Otherwise, assess the victim’s condition and then call for help. – Determine whether the person needs rescue breathing or external cardiac compressions; then take appropriate action. In addition, use the following guidelines when working with any equipment that is disconnected from a

• Cisco WS-C1924-A - Catalyst 1900 24 Ports 10MB Switch, 4-24 Cisco 1900 Series Hardware Installation OL-19084-02 Chapter 4 Installing and Connecting the Router Connecting Power Figure 4-14 DC Power Wire Connection Warning This unit might have more than one power supply connection. All connections must be removed to de-energize the unit. Statement 1028 Warning The illustration shows the DC power supply terminal block. Wire the DC power supply as illustrated. The proper wiring sequence is ground to ground, positive to positive, and negative to negative. The groun

• Cisco WS-C1924-A - Catalyst 1900 24 Ports 10MB Switch, 4-15 Cisco 1900 Series Hardware Installation OL-19084-02 Chapter 4 Installing and Connecting the Router Connecting to a Console Terminal or Modem To connect the router to a terminal or PC, follow these steps: Procedure Step 1 Connect the end of the console cable with the RJ-45 connector to the light blue console port on the router, or USB 5-pin mini Type-B to the USB console port as shown in Figure 4-12. If connecting the USB port for the first time on a Windows based PC, you must install the Windows USB drive

• Cisco WS-C1924-A - Catalyst 1900 24 Ports 10MB Switch, Contents iv Cisco 1900 Series Hardware Installation General Guidelines 2-1 Safety with Electricity 2-2 Preventing Electrostatic Discharge Damage 2-3 General Site Requirements 2-3 Power Supply Considerations 2-4 Site Environment 2-4 Site Configuration 2-4 Wireless LAN Considerations 2-5 Inspecting the Router 2-5 Installation Checklist 2-5 Site Log 2-6 Required Tools and Equipment for Installation and Maintenance 2-7 CHAPTER 3 Cable Information and Specifications for Cisco 1900 Series Routers 3-1 Console and Auxiliary Port Considerations 3-1 About Console and Auxiliary Por

• Cisco WS-C1924-A - Catalyst 1900 24 Ports 10MB Switch, 4-2 Cisco 1900 Series Hardware Installation OL-19084-02 Chapter 4 Installing and Connecting the Router Safety Warnings If you need to remove or upgrade either of these items, follow the procedures given in Installing and Upgrading Internal Modules and FRUs in Cisco 1900 Series ISRs. Plug-In Modules The following components plug into the router chassis: • WAN interface cards (WICs) • Voice/WAN interface cards (VWICs), data mode only • High-speed WICs (HWICs) • Enhanced High-speed WICs (EHWICs) • Compact F

• Cisco WS-C1924-A - Catalyst 1900 24 Ports 10MB Switch, 3-3 Cisco 1900 Series Hardware Installation OL-19084-01 Chapter 3 Cable Information and Specifications for Cisco 1900 Series Routers Preparing to Connect to a Network Auxiliary Port Connections The router has an EIA/TIA-232 asynchronous serial auxiliary port (RJ-45) that supports flow control. Depending on the cable and the adapter used, this port will appear as a DTE or DCE device at the end of the cable. For connection to a modem, your router is provided with an RJ-45-to-DB-9 cable and a DB-9-to-DB-25 adapter. For detailed information about connecting devices to the auxiliary port, see the “Connecting to the Auxiliary Port” section on page 4-20. For cable and p

• 5-21 Cisco 1900 Series Hardware Installation OL-19084-02 Chapter 5 Configuring the Router Performing the Initial Configuration on the Router The following display shows sample output for the ping command when you ping the IP hostname donald: Router# ping donald Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.168.7.27, timeout is 2 seconds: !!!!! Success rate i

Related Products and Documents (Switch):

Comparable Devices:

Similar Resources:

• EtherWAN EX38000A (17 pages) Industrial PoE Ethernet Switch Quick Start Guide This quick start guide describes how to install and use the Industrial PoE Ethernet Switch. This is the switch of choice for harsh environments constrained by space. Physical Description The Port Status LEDs and Power Inputs 1 …

• Omron D2F (12 pages) 197Ultra Subminiature Basic SwitchD2FSubminiature Size Ideal for PCBMounting (12.8 6.5 5.8 (W H D))Incorporating a snapping mechanism made withtwo highly precise split springs that ensures a longservice life.Insertion molded terminals and a two-stage bottomwith different levels prevent flux penetration.Self-clinching PCB, right-angled, left-angled, andsolder …

• Cisco 2948G - Catalyst Switch (142 pages) Corporate HeadquartersCisco Systems, Inc.170 West Tasman DriveSan Jose, CA 95134-1706USAhttp://www.cisco.comTel: 408 526-4000800 553-NETS (6387)Fax: 408 526-4100Catalyst 2984G, 2948G-GE-TX, and 2980G Switch Hardware Installation GuideOctober 2003Customer Order Number: DOC-786286=Text Part Number: 78-6286-05 …

• Extreme Networks BlackDiamond 6816 (3 pages) Part Number: 121042-00 Rev 02 1BlackDiamond 6816 Fan Tray Installation NoteThis installation note describes removing and installing fan trays in the BlackDiamond® 6816 chassis. The fan trays are hot-swappable. You do not need to turn off power to a BlackDiamond 6816 switch to replace the fan tray.Caution: Only trained service personnel should perform servic …

• Control 4 C4-SW1-Z (3 pages) Wireless Switch Installation GuideSupported Models and Requirements • C4-SW1-ZWirelessSwitch(802.15.4),WhiteSpecications and Supported FixturesThisControl4®WirelessSwitchoperatesindependentlyoraspartofaControl4®homeautomationsystemtoenableintelligentlightingcontrol.Itins …

• IPGARD SA-DVN-2S (2 pages) 2 Port DVI-I secure KVM switchCONSOLEK/MSA-DVN-2SAUDIOK/MK/M12VDC2.0AAUDIOAUDIOIN-2 IN-11 2ST1 ST2DVI OUT DVI IN2 DVI IN1TECHNICAL SPECIFICATIONSSA-DVN-2SAdvanced 2-Port Secure Single-head DVI-I KVM Switch with Audio Quick Start Guide VIDEOHost Interface (2) DVI-I 29-pin FUser Console Interface(1) DVI-I 29-pin FMax Resolution2560 x 1600 @ 60Hz; 3840 x 2160 @ …

Comments, Questions and Opinions: