Manualios.com

Cisco SPS2024 Reference Manual

Cisco SPS2024 Manual Online:

3.1, 2405 votes
Cisco SPS2024 User Manual
Cisco SPS2024 User Guide
Cisco SPS2024 Online Manual

Text of Cisco SPS2024 User Guide:

  • Cisco SPS2024, User Interface Commands end SPS208G/SPS224G4/SPS2024 Command Line Interface Reference Guide 466 33 User Guidelines There are no user guidelines for this command. Example The following example closes an active terminal session. Console> exit end The end command ends the current configuration session and returns to the Privileged EXEC mode. Syntax end Default Configuration This command has no default configuration. Command Mode All configuration modes. User Guidelines There are no user guidelines for this command. Example The following example changes from Global Configuration mode to Privileged EXEC mode.

  • Cisco SPS2024, 17 SPS208G/SPS224G4/SPS2024 Command Line Interface Reference Guide 235 LACP Commands lacp system-priority The lacp system-priority Global Configuration mode command configures the system priority. Use the no form of this command to restore the default configuration. Syntax lacp system-priority value no lacp system-priority Parameters • value — Specifies system priority value. (Range: 1-65535) Default Configuration The default system priority is 1. Command Mode Global Configuration mode User Guidelines There are no user gu

  • Cisco SPS2024, Ethernet Configuration Commands set interface active SPS208G/SPS224G4/SPS2024 Command Line Interface Reference Guide 165 12 Example In the following example, the counters for interface 1 are cleared. Console# clear counters ethernet e1 set interface active The set interface active Privileged EXEC mode command reactivates a shutdown interface. Syntax set interface active {ethernet interface | port-channel port-channel-number } Parameters • interface — Valid Ethernet port. • port-channel-number — Valid port-channel number. Defa

  • VLAN Commands interface vlan SPS208G/SPS224G4/SPS2024 Command Line Interface Reference Guide 483 34 Example The following example defines the default VLAN. Console(config-vlan)# default-vlan vlan interface vlan The interface vlan Global Configuration mode command enters the Interface Configuration (VLAN) mode. Syntax interface vlan vlan-id Parameters • vlan-id — Specifies a

  • Cisco SPS2024, SSH Commands crypto certificate export SPS208G/SPS224G4/SPS2024 Command Line Interface Reference Guide 417 29 Subject: CN= router.gm.com, 0= General Motors, C= US Finger print: DC789788 DC88A988 127897BC BB789788 crypto certificate export To export the certificate and the RSA keys, use the crypto certificate export command in Privileged EXEC mode. Syntax crypto certificate number export Parameters • number — Specifies the certificate number. Range: 1 - 2 digits Default Configuration There is no default configuration for this command. Command Mode Privileged EXEC User Guidelines The crypto certificate export command creates a fil

  • Cisco SPS2024, Syslog Commands file-system logging SPS208G/SPS224G4/SPS2024 Command Line Interface Reference Guide 429 30 Example The following example enables logging messages related to AAA login events. Console(config)# aaa logging login file-system logging To control logging file system events, use the file-system logging command in global configuration mode. Use the no form to disable logging. Syntax file-system logging copy no file-system logging copy file-system logging delete-rename no file-system logging delete-rename Parameters • copy — Log messages re

  • Cisco SPS2024, QoS Commands traffic-shape SPS208G/SPS224G4/SPS2024 Command Line Interface Reference Guide 289 23 traffic-shape The traffic-shape Interface Configuration (Ethernet, port-channel) mode command configures the shaper of the egress port/queue. Use the no form of this command to disable the shaper. Syntax traffic-shape { committed-rate excess-burst } [ queue-id ] no traffic-shape [ queue-id ] Parameters • committed-rate — Specifies the average traffic rate (CIR) in bits per second (bps). (CIR range: 64–62500 Kbps, CBS: 8192-16769020 bytes) • exces

  • Spanning Tree Commands show spanning-tree SPS208G/SPS224G4/SPS2024 Command Line Interface Reference Guide 401 28 (configured:no) Designated bridge Priority: 32768Address: 00:02:4b:29:7a:00 Designated port id: 128.1 Designated path cost: 20000 Number of transitions to forwarding state: 1 BPDU: sent 2, received 120638 Port 2 (e2) enabled State: Forwarding Role: Designated Po

  • Cisco SPS2024, System Management Commands traceroute SPS208G/SPS224G4/SPS2024 Command Line Interface Reference Guide 438 31 ----10.1.1.1 PING Statistics---- 4 packets transmitted, 4 packets received, 0% packet loss round-trip (ms) min/avg/max = 7/8/11 traceroute The traceroute User EXEC mode command discovers routes that packets actually take when traveling to their destination. Syntax traceroute { destination-ip-address | hostname } [size packet-size ] [ttl max-ttl ] [count packet-count ] [timeout time-out ] [source source-ip-address ] [tos tos ] Parameters • destination-ip-address — IP address of the desti

  • Cisco SPS2024, Introduction Editing Features SPS208G/SPS224G4/SPS2024 Command Line Interface Reference Guide 30 1 Command Completion If the command entered is incomplete, invalid or has missing or invalid parameters, then the appropriate error message is displayed. This assists in entering the correct command. By pressing Ta b after an incomplete command is entered, the system will attempt to identify and complete the command. If the characters already entered are not enough for the system to identify a single matching command, press ? to display the available commands matching the characters already

  • AAA Commands enable authentication SPS208G/SPS224G4/SPS2024 Command Line Interface Reference Guide 38 2 Syntax enable authentication {default | list-name } no enable authentication Parameters • default — Uses the default list created with the aaa authentication enable command. • list-name — Uses the indicated list created with the aaa authentication enable command. Default Co

  • Cisco SPS2024, Ethernet Configuration Commands port storm-control include-multicast SPS208G/SPS224G4/SPS2024 Command Line Interface Reference Guide 177 12 User Guidelines Use the port storm-control broadcast enable Interface Configuration mode command to enable Broadcast storm control. Example The following example configures a port storm-control Broadcast rate of 4000 on port e2. Console(config)# interface ethernet e2 Console(config-if)# port storm-control broadcast rate 4000 port storm-control include-multicast The port storm-control include-multicast Interface Configuration mode command enables counting Multicast packets in the port storm-control broadcast rate command. U

  • Cisco SPS2024, User Interface Commands help SPS208G/SPS224G4/SPS2024 Command Line Interface Reference Guide 467 33 Console(config)# end Console# help The help command displays a brief description of the help system. Syntax help Default Configuration This command has no default configuration. Command Mode All command modes User Guidelines There are no user guidelines for this command. Example The following example describes the help system. Console# help Help may be requested at any point in a command by entering a question mark ‘?’. If nothing matches the

  • Cisco SPS2024, 802.1x Commands show dot1x statistics SPS208G/SPS224G4/SPS2024 Command Line Interface Reference Guide 532 36 Example The following example displays 802.1x users. console(config-if)# show dot1x users Session Auth MAC Port Username Time Method Address VLAN ------ ----------- ---------- ------ -------------- ---- e1 dva5 00:00:06 Remote 00:05:74:94:2a:1c 5 e2 admin 00:04:04 Remote 00:05:1c:18:0a:7e The following table describes the significant fields shown in the display. show dot1x statistics The show dot1x statistics Privileged EXEC mode command displays 802.1x statistics for the specified interfa

  • QoS Commands qos cos SPS208G/SPS224G4/SPS2024 Command Line Interface Reference Guide 300 23 Default Configuration qos trust is enabled on each port when the system is in basic mode. Command Mode Interface Configuration (Ethernet, port-channel) mode User Guidelines There are no user guidelines for this command. Example The following example configures Ethernet port e15 to the default

  • Cisco SPS2024, DHCP Auto-configuration show ip dhcp autoconfig SPS208G/SPS224G4/SPS2024 Command Line Interface Reference Guide 149 11 show ip dhcp autoconfig To show the status of the IP DHCP autoconfig mode use the show ip dhcp autoconfig EXEC command. Syntax show ip dhcp autoconfig Command Mode EXEC Example Device# show ip dhcp autoconfig DHCP autoconfig enabled Ip dhcp autoconfig filename /config/configfile1.txt

  • Cisco SPS2024, Spanning Tree Commands spanning-tree cost SPS208G/SPS224G4/SPS2024 Command Line Interface Reference Guide 372 28 spanning-tree cost The spanning-tree cost Interface Configuration mode command configures the spanning tree path cost for a port. Use the no form of this command to restore the default configuration. Syntax spanning-tree cost cost no spanning-tree cost Parameters • cost — Path cost of the port (Range: 1-200,000,000) Default Configuration Default path cost is determined by port speed and path cost method (long or short) as shown below: Command Modes Interface Configuration (Ethernet, port-channel) mode User Guidelines The path cost method is co

  • Cisco SPS2024, GVRP Commands show gvrp error-statistics SPS208G/SPS224G4/SPS2024 Command Line Interface Reference Guide 191 13 Command Mode Privileged EXEC mode User Guidelines There are no user guidelines for this command. Example The following example displays GVRP statistical information. Console# show gvrp error-statistics GVRP Error Statistics Legend: INVPROT : Invalid Protocol Id INVALEN : Invalid Attribute Length INVATYP : Invalid Attribute Type INVEVENT: Invalid Event INVAVAL : Invalid Attribute Value Port INVPROT INVATYP INVAVAL INVALEN INVEVENT

  • Cisco SPS2024, Address Table Commands show bridge multicast address-table static SPS208G/SPS224G4/SPS2024 Command Line Interface Reference Guide 94 5 NOTE A Multicast MAC address maps to multiple IP addresses as shown above. show bridge multicast address-table static The show bridge multicast address-table static Privileged EXEC mode command displays the statically configured Multicast addresses. Syntax show bridge multicast address-table static [vlan vlan-id ] [address mac-multicast- address | ip-multicast-address ] [source ip-address ] Parameters • vlan-id — Indicates the VLAN ID. This has to be a valid VLAN ID value. • mac-multicast-address — A valid MAC Multicast address. • ip-m

  • Contents SPS208G/SPS224G4/SPS2024 Command Line Interface Reference Guide 2 show interfaces access-lists 62 Chapter 4: ARP Inspection Commands 64 ip arp inspection 64 ip arp inspection vlan 65 ip arp inspection trust 66 ip arp inspection validate 67 ip arp inspection list create 68 ip mac 69 ip arp inspection list assign 70 ip arp inspection logging interval 71 show ip arp inspection 72 show

  • Cisco SPS2024, Web Server Commands ip https exec-timeout SPS208G/SPS224G4/SPS2024 Command Line Interface Reference Guide 511 35 ip https exec-timeout The ip https exec-timeout Global Configuration mode command sets the interval that the system waits for user input in https sessions, prior to automatic logoff. Use the no form of this command to return to default. Syntax ip https exec-timeout minutes [ seconds ] no ip https exec-timeout Parameters • minutes — Integer that specifies the number of minutes. Range: 1 - 65535. �

  • Cisco SPS2024, ARP Inspection Commands ip arp inspection logging interval SPS208G/SPS224G4/SPS2024 Command Line Interface Reference Guide 71 4 Example The following example assigns static ARP binding lists to a VLAN. Console(config)# ip arp inspection list assign ip arp inspection logging interval The ip arp inspection logging interval Global Configuration mode command configures the minimal interval between successive ARP SYSLOG messages. To return to the default configuration, use the no form of this command. Syntax ip arp inspection logging interval { seconds | infinite} no ip arp in

  • Cisco SPS2024, SNMP Commands snmp-server user SPS208G/SPS224G4/SPS2024 Command Line Interface Reference Guide 339 26 User Guidelines The Router context is translated to “” context in the MIB. Example The following example attaches a group called user-group to SNMPv3 and assigns to the group the privacy security level and read access rights to a view called user-view. Console(config)# snmp-server group user-group v3 riv read user- view snmp-server user The snmp-server user Global Configuration mode command configures a new SNMP Version 3 user. Use the no form of this command to remove a user. Syntax snmp-server user username groupname [remote engineid-string ]

  • Cisco SPS2024, LACP Commands show lacp ethernet SPS208G/SPS224G4/SPS2024 Command Line Interface Reference Guide 238 17 Example The following example assigns a long administrative LACP timeout to Ethernet port e6. Console(config)# interface ethernet e6 Console(config-if)# lacp timeout long show lacp ethernet The show lacp ethernet Privileged EXEC mode command displays LACP information for Ethernet ports. Syntax show lacp ethernet interface [parameters | statistics | protocol-state] Parameters • interface — Valid Ethernet port. • paramet

  • Cisco SPS2024, 802.1x Commands dot1x mac-authentication SPS208G/SPS224G4/SPS2024 Command Line Interface Reference Guide 544 36 Console# configure Console(config)# interface ethernet e1 Console(config-if)# dot1x guest-vlan enable dot1x mac-authentication The mac-authentication Interface Configuration mode command enables authentication based on the station’s MAC address. Use the no form of this command to disable MAC authentication. Syntax dot1x mac-authentication {mac-only | mac-and-802.1x} no dot1x mac-authentication Parameters • mac-only — Enable authentication based on the station’s MAC address only. 802.1X frames are ignored. • mac-and-802.1x —Enable 802.1X authentication and MAC

  • Cisco SPS2024, Management ACL Commands show management access-list SPS208G/SPS224G4/SPS2024 Command Line Interface Reference Guide 252 19 Example The following example denies all ports in the access list called ‘mlist’. Console(config)# management access-list mlist Console(config-macl)# deny ip-source 172.16.15.3 show management access-list The show management access-list Privileged EXEC mode command displays management access lists. Syntax show management access-list Default Configuration This command ha

More Instructions:

DOWNLOAD

Related Products and Documents (Switch):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Rail King 4-6-4 Hudson Steam Locomotive Operator's manual rail-king/4-6-4-hudson-steam-locomotive-DBR.pdf 03 Oct 2022 29
2 Motorola W218 Operation & user’s manual motorola/w218-U34.pdf 13 Aug 2022 1
3 Philips AS 445 Owner's manual philips/as-445-6PL.pdf 03 May 2023 18 0.7 Mb
4 Insignia NS-32D200NA14 Manual d'installation rapide insignia/ns-32d200na14-K2Q.pdf 06 Dec 2023 2
5 Logitech POWERSHELL Setup manual logitech/powershell-4YK.pdf 26 Jul 2023 120
6 Acer AL708 Operation & user’s manual acer/al708-RQC.pdf 23 Sep 2022 9 0.1 Mb

Similar Resources:

  • LevelOne

    FGP-1031

    (16 pages)
    Quick Installation GuideEnglishDeutschFrançaisEspañolNederlandsDanskItalianoΕλληνικάPortuguês Svenska Slovenščina䷩橼󰵶㔯РусскийPolskiCE marking is a certification mark that indicates conformity with health, safety, and environmental protection standards for products sold within the European Economic Area (EEA).The CE marking is also …
  • TRENDnet

    TEG-224WS - Gigabit Web Smart Switch

    (2 pages)
    TRENDnet's TEG-224WS 26-port 10/100/1000Mbps Web-Based Smart Switch is the ideal Switch for network segmenting and flexibility. It has 24 10/100Mbps and 2 10/100/1000Mbps Auto-Sensing and Auto-MDIX ports. TEG-224WS supports web browser configuration allowing Network Administrators to configure speed, VLAN, QoS, Trunking and Mirroring down to the port l …
  • Quintech

    RFS 2150/2

    (4 pages)
    Available From MEGA HERTZ (Master Distributor) • 800.883.8839 • http://www.megahz.com  2003 Quintech Inc. All rights reserved. All product designs and specifications are subject to change without notice. RFS21502BAA000 Rev C Model — RFS 2150/2 Part No. RFS21502BAA000 L-Band RF Sensing Switch General Description: The RFS21502BAA000 L-Band RF Sen …
  • S&C

    Alduti-Rupter

    (24 pages)
    March 4, 2019© S&C Electric Company 1998-2019, all rights reservedInstruction Sheet 761-507S&C Alduti-Rupter® SwitchesOutdoor Distribution (46 kV)Three-Pole Double-Break Integer StyleReciprocating Operating Mechanism No Catalog Number Supplement Installation and OperationTable of ContentsSection Page Section PageIntroductionQualified Persons . …
  • Intermatic

    EMDS

    (1 pages)
    INSTALLING THE EMDSThe EMDS is a 100% digital center-off momentary switch that looks like an ordinary wall switch and provides a famil-iar interface to the digital bus. This switch is NOT pre-pro-grammed and must be addressed and programmed in the field. Placement and WiringConnect to the digital lighting control bus using Cat. 5 cable with RJ45 connectors. …
  • Wyrestorm

    SW-0501-HDBT

    (16 pages)
    Copyright © 2018 WyreStorm Technologies | Product specifications or appearance subject to change without notice. Installation Guide SW-0501-HDBT Document Revision: v2.0 Document Date: March 6th 2018 Supported Firmware: V1.0.0 or higher …

Comments, Questions and Opinions: