Cisco WS C4224V 8FXS - 200Mbps Ethernet Switch Software Configuration Manual

Text of Cisco WS C4224V 8FXS - 200Mbps Ethernet Switch User Guide:

• Cisco WS C4224V 8FXS - 200Mbps Ethernet Switch, Chapter 6 Configuring VoIP Configure Voice Ports 6-26 Catalyst 4224 Access Gateway Switch Software Configuration Guide OL-2031-02 Step 3 Specify (in dB) the amount of gain to be inserted at the receiver side of the interface. input gain value –6 to 14 dB 0 dB Step 4 Specify (in dB) the amount of attenuation at the transmit side of the interface. output attenuation value 0 to 14 dB 0 dB Step 5 Enable echo-cancellation of voice that is sent out of the interface and received back on the same interface. echo-cancel enable Step 6 Adjust the size (in milliseconds) of the e

• Cisco WS C4224V 8FXS - 200Mbps Ethernet Switch, Chapter 3 Configuring Ethernet Switching Managing the Catalyst 4224 Access Gateway Switch 3-16 Catalyst 4224 Access Gateway Switch Software Configuration Guide OL-2031-02 A detection mechanism on the Catalyst 4224 determines whether it is connected to a Cisco 7960 IP Phone. If the switch senses that there is no power on the circuit, the switch supplies the power. If there is power on the circuit, the switch does not supply it. You can configure the switch to never supply power to the Cisco 7960 IP Phone and to disable the detection mechanism. Beginning in privileged EXEC mode, follow these steps to c

• Chapter 10 Traffic Shaping Low-Latency Queueing 10-14 Catalyst 4224 Access Gateway Switch Software Configuration Guide OL-2031-02 Restrictions DTS does not support the following: • Fast EtherChannel, Multilink PPP (MLP), Tunnel, VLANs, and dialer interface • Any VIP below a VIP2-40 Note A VIP2-50 is strongly recommended when the aggregate line rate of the port adapte

• Cisco WS C4224V 8FXS - 200Mbps Ethernet Switch, 3-19 Catalyst 4224 Access Gateway Switch Software Configuration Guide OL-2031-02 Chapter 3 Configuring Ethernet Switching Managing the Catalyst 4224 Access Gateway Switch Figure 3-3 Contents of the Address Table MAC Addresses and VLANs All MAC addresses are associated with one or more VLANs. An address can exist in more than one VLAN and have different destinations in each. Multicast addresses, for example, could be forwarded to port 1 in VLAN 1 and ports 9, 10, and 11 in VLAN 5. Each VLAN maintains its own logical address table. A known address in one VLA

• Cisco WS C4224V 8FXS - 200Mbps Ethernet Switch, 1-13 Catalyst 4224 Access Gateway Switch Software Configuration Guide OL-2031-02 Chapter 1 Product Overview Application Notes • The two-Port FXS and FXO VIC uses two of the available four DSO channels. The DSP is used when the VIC is plugged in, even if the ports are not configured. • The eight-Port FXS Module uses eight DS0 channels or two DSPs, even if it is not used (unless it is disabled using the CLI). The following sample configuration shows DSP allocations: C4224# sh voice dsp BOOT TYPE DSP CH CODEC VERS STATE STATE RS

• Cisco WS C4224V 8FXS - 200Mbps Ethernet Switch, 2-7 Catalyst 4224 Access Gateway Switch Software Configuration Guide OL-2031-02 Chapter 2 Configuring for the First Time Using the Cisco IOS CLI Timesaver Each command mode restricts you to a subset of commands. If you are having trouble entering a command, check the prompt and enter the question mark (?) for a list of available commands. You might be in the wrong command mode or using the wrong syntax. Global configuration From the privileged EXEC mode, enter the configure terminal command. hostname (config)# The default is router (config)# To exit to privileged EXEC mode, use the exit or end command, or press Ctrl-Z.

• Chapter 7 Configuring the Eight-Port FXS RJ-21 Module Configuring FXS Voice Ports 7-4 Catalyst 4224 Access Gateway Switch Software Configuration Guide OL-2031-02 Validating the Configuration To validate your voice port configuration, perform one or both of the following tasks: • Pick up the handset of a telephony device attached to your IP network and check for a di

• Chapter 3 Configuring Ethernet Switching Managing the Catalyst 4224 Access Gateway Switch 3-10 Catalyst 4224 Access Gateway Switch Software Configuration Guide OL-2031-02 Sample Configuration The following example illustrates the configuration on the IP phone: interface FastEthernetx/x switchport voice vlan x The following example illustrates the configuration on the PC: in

• Cisco WS C4224V 8FXS - 200Mbps Ethernet Switch, 10-5 Catalyst 4224 Access Gateway Switch Software Configuration Guide OL-2031-02 Chapter 10 Traffic Shaping About Traffic Shaping Table 10-1 summarizes these differences. You can configure GTS to behave the same as FRTS by allocating one DLCI per subinterface and using GTS plus backward explicit congestion notification (BECN) support. Table 10-1 Differences Between Shaping Mechanisms Mechanism GTS Class-Based DTS FRTS Command-Line Interface • Applies parameters per subinterface • traffic group command supported • Applies parameters per interface or per class • Applies parameters per interface or subinterface • Classes of parameters • Applies parameters to

• Cisco WS C4224V 8FXS - 200Mbps Ethernet Switch, 4-17 Catalyst 4224 Access Gateway Switch Software Configuration Guide OL-2031-02 Chapter 4 Configuring the Data Interfaces Configuring T1 and E1 Interfaces Step 8 Specify the channel group and time slots to be mapped. When configuring a E1 data line, channel-group numbers can be values from 0 to 30. Time slots are assigned to channels. One or more time slots or ranges of time slots belong to the channel group. The first time slot is numbered 1. For an E1 controller, the time slot range is from 1 to 31. For E1 PRI scenarios, all 31 T1 time slots are assigned as ISDNPRI channels. The default line speed w

• Cisco WS C4224V 8FXS - 200Mbps Ethernet Switch, Chapter 1 Product Overview Recommended Configurations 1-26 Catalyst 4224 Access Gateway Switch Software Configuration Guide OL-2031-02 progress_ind alert enable 8 port 3/1:23 forward-digits all Note alert enable 8 is a hidden command option, which you cannot find by using the ? at the CLI. The following sample configuration shows what happens when you try to find this command option: C4224-2(config-dial-peer)# progress_ind alert ? % Unrecognized command This ringback situation applies only to

• Cisco WS C4224V 8FXS - 200Mbps Ethernet Switch, iii Catalyst 4224 Access Gateway Switch Software Configuration Guide OL-2031-02 CONTENTS Preface xvii Objectives xvii Audience xviii Organization xviii Related Documentation xix Conventions xx Obtaining Documentation xxi Cisco.com xxi Documentation CD-ROM xxi Ordering Documentation xxii Documentation Feedback xxii Obtaining Technical Assistance xxiii Cisco.com xxiii Technical Assistance Center xxiii Cisco TAC Website xxiv Cisco TAC Escalation Center xxv Obtaining Additional Publications and Information xxv CHAPTER 1 Product Overview 1-1 Features 1-2 Solution 1-3 IP Telephony 1-5 Ethernet Switching 1-5 Survivable Remote Site Telephony 1-6

• Cisco WS C4224V 8FXS - 200Mbps Ethernet Switch, Chapter 1 Product Overview Application Notes 1-12 Catalyst 4224 Access Gateway Switch Software Configuration Guide OL-2031-02 The DSPs compress and decompress packets based on codecs. The Catalyst 4224 supports the following codecs: • G.711 a-law 64 Kbps • G.711 mu-law 64 Kbps • G.729 abr 8 Annex-A & B 8 Kbps • G.729 ar8 G729 Annex-A 8 Kbps • G 729 r8 G729 8 Kbps The number of DSP channels that you can use depends upon the VIC configuration. The following rules apply when you allocate DSP channels for T-1/E-1 VWICs: • The eight-port FXS Module us

• Cisco WS C4224V 8FXS - 200Mbps Ethernet Switch, Index IN-10 Catalyst 4224 Access Gateway Switch Software Configuration Guide OL-2031-01 switchover 5-5 switchover command 5-6 Switch Port Analyzer (SPAN) disabling 3-17 enabling 3-16 T T1 channel bank 5-19 T1 interface configuring 4-12 terminal, connecting to 2-3 timeout, disabling 4-3 time slots, configuring 5-9 timeslots, configuring 5-20 traffic monitoring 3-16 traffic shaping defined 10-1 Distributed benefits 10-13 prerequisites 10-12 restrictions 10-14 excess burst size 10-3 FRTS 10-9 GTS 10-6 queueing 10-6 uses

• Cisco WS C4224V 8FXS - 200Mbps Ethernet Switch, 4-15 Catalyst 4224 Access Gateway Switch Software Configuration Guide OL-2031-02 Chapter 4 Configuring the Data Interfaces Configuring T1 and E1 Interfaces Step 9 Specify the channel group and time slots to be mapped. When configuring a T1 data line, channel-group numbers can be values from 0 to 23. Time slots are assigned to channels. One or more time slots or ranges of time slots belong to the channel group. The first time slot is numbered 1. For a T1 controller, the time slot range is from 1 to 24. For T1 PRI scenarios, all 24 T1 time slots are assigned as ISDN/PRI chann

• Cisco WS C4224V 8FXS - 200Mbps Ethernet Switch, Chapter 7 Configuring the Eight-Port FXS RJ-21 Module Sample Configuration 7-12 Catalyst 4224 Access Gateway Switch Software Configuration Guide OL-2031-02 >ip classless >ip route 8.1.1.0 255.255.255.0 30.1.1.1 >no ip http server >! >snmp-server packetsize 4096 >call rsvp-sync >! >voice-port 1/1/0 >! >voice-port 1/1/1 >! >dial-peer cor custom >! >dial-peer voice 1 pots > destination-pattern 10 > port 1/1/0 >! >dial-peer voice 2 voip > destination-pattern 20 > session target ipv4:172.20.59.93 >! >line

• Cisco WS C4224V 8FXS - 200Mbps Ethernet Switch, 8-13 Catalyst 4224 Access Gateway Switch Software Configuration Guide OL-2031-02 Chapter 8 Configuring Survivable Remote Site Telephony SRST Configuration Example no ip address ! interface TokenRing1/0 no ip address shutdown ! ip kerberos source-interface any ip classless no ip http server ! snmp-server packetsize 4096 snmp-server manager call rsvp-sync ! mgcp modem passthrough voip mode ca no mgcp timer receive-rtcp ! mgcp profile default ! dial-peer cor custom ! call-manager-fallback ip so

• Cisco WS C4224V 8FXS - 200Mbps Ethernet Switch, Chapter 5 Configuring the Voice Interfaces Configuring Voice Interfaces 5-2 Catalyst 4224 Access Gateway Switch Software Configuration Guide OL-2031-02 When you start a Catalyst 4224, it automatically detects the voice network modules and VICs that have been installed. The first time you use a Catalyst 4224, you need to configure each voice port that you want to enable. If you replace a card after you configure each port, the gateway will recognize the new hardware component and use the previous configuration settings. If you replace a module that was already configured, the gateway recognizes it and brings up the interface in the exis

• Cisco WS C4224V 8FXS - 200Mbps Ethernet Switch, 1-19 Catalyst 4224 Access Gateway Switch Software Configuration Guide OL-2031-02 Chapter 1 Product Overview Configuration Guidelines Separate VLAN for Voice and Data Unlike the Catalyst 3500, you do not need to preconfigure VLANs with a VLAN database command. To be consistent with Cisco IP Telephony QoS design guidelines, you should configure a separate VLAN for voice and data. The following example shows a recommended configuration. interface FastEthernet5/22 no ip address duplex auto speed auto switchport access vlan 60 switchport voice vlan 160 snmp trap link-status spanning-tree portfast This sample configuration instructs the IP ph

Related Products and Documents (Switch):

Comparable Devices:

Similar Resources:

• LEGRAND Wattstopper EOSW Series (12 pages) Wattstopper ®Wireless Lighting Control System EOSW Series Wall Switch Receivers with NeutralSystème de contrôle de l’éclairage sans fil Récepteurs interrupteurs muraux de la série EOSW avec neutreSistema de control de iluminación inalámbrico Receptores con interruptor de pared serie EOSW con neutroInstallation Instructions • Instructions d’Inst …

• ADDER ALGTX (54 pages) INSTALLATION&USEwww.addertec.comAL Extender pairALTX/ALRXAL Silver pairALSTX/ALSRXAL Gold pairALGTX/ALGRXADDER LLiinnkkADDER LLiinnkkThe AdderLink contains fine videocompensation amplifiers to maximisethe video quality for any given lengthof twisted pair cable.To adjust thecompensation and sharpen the videopicture refer to section 2.8 …

• Tesla smart HKS1601A10 (4 pages) Tesla smart1 www.tesla-smart.com16x1 HDMI KVM Switch# HKS1601A10This 16x1 HDMI KVM switch provides you with great flexibility in integrating cross-platformcomputer equipment easily. It makes you available to switch easily and reliably betweenany HDMI computers using one HDMI compliant display.The 16x1 HDMI KVM switch supports USB 2.0 hub and USB 2.0 keyboard …

• 3Com SuperStack 3 3870 (76 pages) http://www.3com.com/Part No. DUA1745-0AAA02Published August 2004SuperStack® 3 Switch 3870 FamilyGetting Started Guide3CR17450-913CR17451-91DUA1745-0AAA02.book Page 1 Monday, August 9, 2004 11:51 AM …

• Juniper EX8216 (2 pages) EX8216 Switch Quick StartTo install and configure a Juniper Networks EX8216 Ethernet Switch, you need:z Mechanical lift (not provided)z Adjustable mounting brackets (4 pieces) with 12 screws total (provided)z 36–40 mounting screws appropriate for your four-post rack (16 to attach the adjustable mounting brackets to the rack, 20 to attach the front-mounting …

• StarTech.com SV431HDU3A (13 pages) Manual Revision: 03/31/2014For the most up-to-date information, please visit: www.startech.comDE: Bedienungsanleitung - de.startech.comFR: Guide de l'utilisateur - fr.startech.comES: Guía del usuario - es.startech.comIT: Guida per l'uso - it.startech.comNL: Gebruiksaanwijzing - nl.startech.comPT: Guia do usuário - pt.startech.comSV231HDU3A / SV43 …

Comments, Questions and Opinions: