Cms Products 674 Operator's Manual

Text of Cms Products 674 User Guide:

• HotCup Operators’ Guide Hot Drink Setup November, 2007 49 6740001 Hot Drink Setup SET UP A HOT DRINK Be sure that the cup sizes you set in (setup cup sizes page, ), agree with the cup sizes actually in your machine. All procedures for setting up the hot drinks are similar, so this example will demonstrate how to set up the A selection, regular size fres

• Cms Products 674, Initial Setup HotCup Operators’ Guide 6740001 18 November, 2007 3. Install the Water Filter Cartridge: IF YOUR MERCHANDISER HAS THE WATER FILTER OPTION, IT CANNOT BE OPERATED WITHOUT A PROPERLY INSTALLED WATER FILTER CARTRIDGE. If you do not have the water filter option, continue with "Fill the Tank". CUNO BRAND ... Note: Check the water filter installation record. There is a place to write the vend number on the cartridge. The cartridge is effective for a maximum of 64,000 7

• Cms Products 674, Product Configuration HotCup Operators’ Guide 6740001 60 November, 2007 CAPPUCCINO Cappuccino is made with various ratios of chocolate to coffee, according to taste. Lightener (E timer) is also used for cappuccino. For an example, the default chocolate-to-coffee ratio of 15/85 in a 8.25 oz. cup consists of the following: • A chocolate throw (DR.2) lasting .65 seconds, providing 15% of the normal chocolate throw (approximately 5.4 grams*). • A water throw for the chocolate (WA.2) lasting 2.65 seconds (chocolate product throw plus 2

• HotCup Operators’ Guide Hot Drink Setup November, 2007 55 6740001 SET THE MACHINE TYPE CONFIGURATION CODE (Supervisor Mode Only) a. Press , then press until the display shows Mach.type (x). b. Press to enter MACH.TYPE (1). c. Press . The display shows CONF WXYZ "WXYZ" is the machine configuration code. c. Press until the display shows D+

• Cms Products 674, HotCup Operators’ Guide Programming The HotCup November, 2007 37 6740001 Press this button to: • Download data into your portable data collection device (PDCD), OR • Set printer baud rate, depending upon which device you are using Press this button to: • Set machine type configuration • Set which selections are active • Set up blended selections • Set up cup sizes Press this button to: • Set time of day • Set day, month, year • Select display messages • Set up time of day intervals for inhibit, freevend, and discount vending • Edit messages • Set message scrolling speed • Press this button to pay on

• Cms Products 674, HotCup Operators’ Guide Testing November, 2007 77 6740001 TEST VEND SELECTIONS AND VERIFY CREDIT ADDED Tes tin g a. Press . The display shows TEST .00. You may now test vend selections. b. To test vend selections without dropping a cup, press . The display shows TEST.NC .00 . No cups will drop during the rest of your test vend session. If desired, you may place money in the machine. In either case, if you insert money into the machine, the zeros in the display will be replaced with the amount of the credit. NOTE You may make one more test vend if you close the door while still in TEST VEND mode. c. CONTINUE. TE

• Cms Products 674, Testing HotCup Operators’ Guide 6740001 78 November, 2007 TEST THE AUTOMATIC DOOR (OPTIONAL) a. Press , then press until the display shows DOOR TEST. b. Press to test the automatic delivery door. The door will open, then close after one second. c. CONTINUE. TEST THE WHIPPERS a. Press , then press until the display shows WHIP TEST. b. Press the whipper number (1=whipper below main condiment mixing bowl, 2=soup whipper, or 3=chocolate whipper) you want to test. OR Press the letter of a selection containing a whipper. In either case, WHIP X is displayed while the whipper under test ("X") runs. c. CONTINUE. TEST THE PUMP a. Pres

• Cms Products 674, Initial Setup HotCup Operators’ Guide 6740001 16 November, 2007 IV. FINAL MECHANICAL PREPARATION 1. Level the Merchandiser: a. Place a spirit level on the top front edge of the cabinet with the door fully closed. Adjust the front legs only until the cabinet is reasonably level. b. Hold the door open about 4 inches. WARNING: HAVE AN ASSISTANT HOLD THE MERCHANDISER WHILE YOU ADJUST THE LEG LEVELERS. c. Adjust the back legs so that the back leg leveler on the hinge side is off the floor just enough so a piece of paper can slide under it with only a bit of resistance. d. For proper weight distribution on all four legs, raise the back leg on the hinge side by unscrewing the levele

• Cms Products 674, Major Parts HotCup Operators’ Guide 6740001 4 November, 2007 INTERIOR VIEW OF MERCHANDISER DOOR CUP MECHANISM TURRET ASSEMBLY AND MOTOR AND PCB ASSEMBLY DELIVERY DOOR LOCK BAR ASSEMBLY FRONT VIEW OF MERCHANDISER 636p0048

• Cms Products 674, HotCup Operators’ Guide Hot Drink Setup November, 2007 51 6740001 VIEW OR SET THE HOT WATER TANK TEMPERATURE a. Press then until the display shows SET 202 °F . In this example, 202° is the water tank temperature setpoint in degrees Fahrenheit. If a decimal point appears next to the “F”, the heater is on. b. If desired, enter a new setpoint in the accepted range of 149° - 205° F (65° - 96° C). NOTE The lower limit for vending is 20° below setpoint, up to a maximum of 180° F (82° C). c. To change display units (replace the “F” with a “C” for Celsius), press . d. Continue. SET UP LOW TEMPERATURE DISP

• Cms Products 674, HotCup Operators’ Guide View Machine Info November, 2007 87 6740001 KEYSWITCH The keyswitch input is active and configured as an inhibit. MACH.TYPE 0 Machine type error displays machine type screen. NOTE: This is the actual machine type screen. You may enter the correct machine type number directly on this screen without further action. D+J+WXYZ Configuration error; displays the machine configuration screen. NOTE: this is the actual config screen. You may enter the correct config number directly on this screen without furthe

• Cms Products 674, HotCup Operators’ Guide Initial Setup November, 2007 21 6740001 4. Load the Optional Filter Paper: a. Turn the fastener 1 / 4 turn counterclockwise and remove the filter paper cover. b. Insert filter paper in the filter paper housing as shown. c. Feed the paper out of the housing as shown by the arrows molded into the back wall of the filter paper housing d. Lift up the limit switch and feed the paper past it as shown. Release the limit switch. e. Replace the cover. . f. Refer to routing label on filter paper cover. Feed paper under paper guide shaft and over rounded edge

• Cms Products 674, HotCup Operators’ Guide Appendix F November, 2007 F-1 6740001 Appendix F The FreeVend Keyswitch Option The free vend keyswitch allows someone to set up free vending without needing to open the door. It is a good idea to establish a free vend code. This will prevent an unauthorized person from setting the machine to free vend, even if they have a key. 1. Press . Enter your 4-digit supervisor code. Press . 2. Press again, then press until the display shows FREE XXXX. Enter a 4-digit free vend code. NOTE To keep the user f

• Initial Setup HotCup Operators’ Guide 6740001 28 November, 2007 11. Test the Machine: Your HotCup merchandiser is now ready to vend coffee, just as soon as the water in the tank reaches its operating temperature. Press , and a reading of the tank temperature is displayed. When the display shows 94° C (202° F), it is ready for vending. a. Close the door,

• HotCup Operators’ Guide Initial Setup November, 2007 29 6740001 12. PosiVend:™ PosiVend™ensures that a cup is always available in the cup station before any money is collected or product delivered. The sensing system is a beam of infra-red light across the cup station which is broken by the cup when it falls into position. The PosiVend™ software monitors the cu

• Cms Products 674, Controls and Indicators HotCup Operators’ Guide 6740001 8 November, 2007 POWER CONTROL PANEL (U.S./CANADA) BACK SIDE OF U.S./CANADA POWER CONTROL PANEL LABEL MAIN CIRCUIT BREAKER MAIN POWER SWITCH LOW VOLTAGE CIRCUIT BREAKER OFF ON DC POWER SUPPLY PCB FOR 110V COIN MECH ˜ AGC 1 FUS E 1 AM P TOP BACK SIDE

• Cms Products 674, Hot Drink Setup HotCup Operators’ Guide 6740001 50 November, 2007 WHIPPER OPTIONS WHP. A XXX Press to view and change the whipper settings as follows: ON- The last 3 seconds of the drink is always whipped ON+ The whole drink is always whipped OFF The drink is never whipped opt See below • If J+ is selected (See “Set the Machine Type Configuration Code” on page 55): OPT- The last 3 seconds of the drink is whipped only when the J key is pressed OPT+ The whole drink is whipped only when the J key is pressed • If J- is selected(See “Set the

• Cms Products 674, Monetary Setup HotCup Operators’ Guide 6740001 44 November, 2007 d. Press to display the desired choice. The value of " X.XX" has two purposes: i. First, " X.XX" tells the machine how big a bill or coin to accept even though there is not enough change in the coin mech to cover all possible paybacks. • For example, enter 1.00. The machine will take a dollar bill or coin even though there is less than $1.00's worth of change. Entering 5.00 tells the machine to take a five even though there is less than $5.00's worth of change, and so forth. NOTE: This could cause a customer to be shortchanged. • Entering 0

• Cms Products 674, Initial Setup HotCup Operators’ Guide 6740001 26 November, 2007 7. Fill the Tank: a. Make sure the main power switch is ON. b. Turn on the water at its source. c. On the service keypad, press , then press until the display shows TANK.FILL. d. Press . You should hear water running into the tank, and the display will show FILLING. The water will run until either the tank is full or 12 minutes go by, whichever happens first. NOTE The inlet water valve only stays open for 12 minutes at a time. This is a safety feature to prevent

• Cms Products 674, HotCup Operators’ Guide View Machine Info November, 2007 81 6740001 VIEW TIME DATA a. Press , then press until the display shows TIME DATA. b. Press . The following message scrolls across the display: MAIN.1 237M 01/30 10.13 This example shows the latest time interval the main (machine) door was open (1). It was open for 237 minutes, and was opened on January 30 (01/30) at 10:13 am (10.13). Press . If applicable, similar displays will appear for intervals 2, 3, and 4, otherwise, go to the next step. c. Press . The following message scrol

• Cms Products 674, HotCup Operators’ Guide Major Parts November, 2007 3 6740001 Major Parts The diagrams on the following pages will acquaint you with the major parts of the HotCup merchandiser. For more detailed information, please consult your PARTS MANUAL. If you do not have a PARTS MANUAL, contact National Vendors Parts Department. FRONT OF MERCHANDISER CRANE NATIONAL VENDORS POINT OF PURCHASE PHOTO ˜ ˜ EXTERIOR DOOR ASSEMBLY LOC K MENU ASSEMBLY

• Cms Products 674, HotCup Operators’ Guide Initial Setup November, 2007 17 6740001 2. Mount the Base Plate: WARNING DO NOT MOVE THE CABINET WHILE HEX HEAD SCREWS AND/ OR CARRIAGE BOLTS ARE LOOSENED. THE CABINET WOULD BECOME UNSTABLE AND LIKELY TO TIP AND CAUSE INJURY. a. Remove the pail(s) from the inside of the merchandiser. b. Remove the floor liner from the inside of the merchandiser. c. Remove the two caps as shown. d. Loosen the left leg assembly carriage bolts and nuts to allow mounting a base plate bracket. e. Secure one of the base plate brackets to the leg assembly using the two carriage bolts. Tighten the carriage bolts and nuts. f.

• Cms Products 674, HotCup Operators’ Guide Appendix E November, 2007 E-1 6740001 Appendix E Clean Hot Water Tank Some smell and/or taste problems may occur in new machines. Follow this procedure to clean the hot water tank if you experience problems: 1. If the machine is in service, remove power from the machine. 2. Dissolve 1 tablespoon of common baking soda in a cup of water. WARNING The water tank may be HOT. Be careful when working on the tank. 3. Loosen or remove the hot water tank lid and pour the baking soda solution into the tank. 4. Apply power to the machine. 5. If the tank is not full, fill it. 6. Allow the tank to reach its operating t

• Cms Products 674, Messages HotCup Operators’ Guide 6740001 76 November, 2007 ENTERING YOUR MESSAGE You will be using a combination of special keys and the keys on the selection switch panel to enter your message. Pressing the keys on the selection switch panel will enter the character shown on that key. Most of the keys on the service keypad have a special purpose to help you create and edit your messages: THE CHARACTER SET Inserts an R at the flashing character. Inserts a space at the flashing character. Inserts an S at the flashing character. Deletes

• HotCup Operators’ Guide Initial Setup November, 2007 27 6740001 9. Load Cups: CAUTION Use only cups which have been designed for use in a hot beverage vending machine. a. Support the cup mechanism in the upright position. b. Push the latch forward to release the cup mechanism. Continue to support the cup mechanism while you lower it into the loading position. c. Remove the tu

• Initial Setup HotCup Operators’ Guide 6740001 20 November, 2007 HYDROLIFE BRAND INSTALLATION: a. Place the filter inside the canister. Be sure the o-ring is seated in the canister just below the threads. b. Screw the canister and filter assembly onto the filter head until it comes to a stop. c. Open the water valve on the inlet line by rotating the handle to the vertical positi

Related Products and Documents (Coffee Maker):

Comparable Devices:

Similar Resources:

• Astoria Core600 AL (288 pages) ASTORIA MACCHINE PER CAFFÈ S.R.L.Via Condotti Bardini, 1 - 31058 SUSEGANA (TV) - ITALY - Tel. +39.0438.6615 - Fax +39.0438.60657 - www.astoria.com - [email protected]/42/CE Direttiva macchine - Machinery Directive2006/42/CE Directive machines - Maschinenrichtlinie2006/42/CE Directiva sobre las máquinas - Directiva sobre máquinasAL - AEP - …

• Mr. Coffee BVMC-MLXX Series (14 pages) User Manual /Manual del UsuarioPERSONAL COFFEEMAKER / CAFETERA PERSONAL BVMC-MLXX Series / Serie BVMC-MLXX©2015 Sunbeam Products, Inc. doing business as Jarden Consumer Solutions. All rights reserved. Distributed by Sunbeam Products, Inc. doing business as Jarden Consumer Solutions, Boca Raton, Florida 33431. U.S. 1-800-MR COFFEE (1-800-672-6333)Canada 1-80 …

• Mr. Coffee BVMC-ECMP1000 (20 pages) © 2012 Sunbeam Products, Inc. doing business as Jarden Consumer Solutions. All rights reserved. Distributed by Sunbeam Products, Inc. doing business as Jarden Consumer Solutions, Boca Raton, Florida 33431. U.S. 1-800-MR COFFEE (1-800-672-6333) Canada 1-800-667-8623Visit us at www.mrcoffee.com You will find exciting and entertaining tips and ideas, including …

• Zelmer 13Z015 (100 pages) (2‐12)INSTRUKCJAUŻYTKOWANIAEkspresciśnieniowyTyp13Z015(13‐22) (23‐33) (34‐43) (44‐54)NÁVODKOBSLUZEKávovarespresoTyp13Z015NÁVODNAOBSLUHUTlakovýkávovarTyp13Z015HASZNÁLATIUTASÍTÁSAutomatakávéfőzőTípus13Z015INSTRUCȚI …

• Salvatore THE AUTOMATIC (6 pages) THE SHOWROOM SINCE 1988 HAND-CRAFTED CUSTOM MADE ESPRESSO MACHINES THE AUTOMATIC OWNER’S MANUAL ESPRESSO SYSTEMS, INC. 1210 Mission Dr, B. Solvang CA 93463 [email protected] www.salvatore-espresso.com 805 688-9807 Create PDF files without this message by purchasing novaPDF printer (http://www.novapdf.com) …

• inventum HK II M/W (28 pages) KOFFIEPADMACHINE - KAFFEEPADMASCHINE - MACHINE À CAFÉ DE DOSETTES - COFFEEPADMACHINEGEBRUIKSAANWIJZING - GEBRAUCHSANLEITUNGMODE D’EMPLOI - INSTRUCTION MANUAL10HK11_GA.indd 1 3-11-2008 10:57:37 …

Comments, Questions and Opinions: