Manualios.com

Compatible Systems MicroRouter 2270R Installation Manual

Compatible Systems MicroRouter 2270R Manual Online:

3.65, 1560 votes
Compatible Systems MicroRouter 2270R User Manual
Compatible Systems MicroRouter 2270R User Guide
Compatible Systems MicroRouter 2270R Online Manual

Text of Compatible Systems MicroRouter 2270R User Guide:

  • Compatible Systems MicroRouter 2270R, Appendix C - LED Patterns and TestSwitch Settings 37 Appendix C - LED Patterns and Test Switch Settings MicroRouter 2270R LED Patterns The MicroRouter 2270R uses a number of light patterns on its front LED bars to indicate operating conditions. Power On, No Traffic The router will scan through the left two (Ethernet) LED bars, from left to right, illuminating one element at a time. Note: Lights 1 and 10 on each bar are directly connected to the router’s 10BaseT interface and indicate 10BaseT link (1) and 10BaseT polarity (10). Ethernet Traffic Indicators (Ethernet LED Bars) Scan from 2 to 5: Ethernet transmit packet Scan from

  • Compatible Systems MicroRouter 2270R, Chapter 5 - Command Line Management 17 SubnetMask,andIPBroadcast keywords in the IP Ethernet 0 (and/or Ethernet 1) section. B. Use the save command to save the changes to the device’s Flash ROM. • You may also use CompatiView from a reconfigured IP host (if using the IP transport protocol), or anywhere on your net- work (if using the IPX transport protocol). Instructions for these two methods are given in Chapter 4 - CompatiView Software Installation. • With CompatiView, basic IP parameters can be set using the TCP/IP R

  • Compatible Systems MicroRouter 2270R, 20 Chapter 6 - Basic Configuration Guide IP Protocol Required for IP These parameters set the basic address characteristics of the interface. They provide enough information for another IP node to find the inter- face (such as a Telnet client), but not enough information for routing to take place. •IPaddress • IP subnet mask • IP broadcast address CV: Use the TCP/IP Routing: Ethernet Dialog Box to set these param- eters. TB: Use the configure command and the IPAddress, SubnetMask, and IPBroadcast keywords in the IP Ethernet 0 (and/or Ethernet 1) section. Suggested for IP The

  • Compatible Systems MicroRouter 2270R, 26 Chapter 6 - Basic Configuration Guide When you set up an on-demand link with AppleTalk, you should care- fully monitor link usage to determine whether the link is being activated only when it is needed. Additional router configuration will be required for many networks in order to achieve optimal link usage. • Set update method CV: Use the AppleTalk Routing: WAN Dialog Box. TB: Use configure and set the Updates keyword in the AppleTalk WAN 0 (and/or WAN 1) section. DECnet Protocol Required for DECnet The router’s shipping configuration does not have DECnet turne

  • Compatible Systems MicroRouter 2270R, 34 Appendix A - Shipping Defaults WAN Interfaces IP Defaults •On • Unnumbered interface •RIPoff • Van Jacobson compression off IPX Defaults •On • Unnumbered interface AppleTalk Defaults •On • Unnumbered interface DECnet Defaults •Off T1 CSU/DSU (WAN 0) Link & Physical Defaults • PPP •FullT1 •Slaveclock • B8ZS encoding • ESF framing •PRMTransmit • Accept V.54 or line loopback commands from remote RS-232 (WAN 1) Link & Physical Defaults • PPP • Dial-in • Async @ 115.2Kbps • Hardware flow control

  • 10 Chapter 3 - Network Installation Connecting the Router to the Ethernet If your twisted-pair hub is already in place, you can connect the router to an active network without interrupting network activity. The router must be powered off. Connecting to Twisted-Pair Ethernet Before connecting the router to twisted-pair cabling you need an unshielded twisted-pair cable that is already con

  • Compatible Systems MicroRouter 2270R, Chapter 3 - Network Installation 11 Note: The MicroRouter 2270R RS-232 interfaces require that your asynchronous line communications device be set to supply the RS-232 DCD signal when a connection has been made. A synchronous RS-232 device should be set to provide DSR. Note: The MicroRouter 2270R includes a special cable to facilitate connections to RS-232 line communications devices. This cable includes support for several asynchronous and synchronous control signals. Off-the-shelf cables generally do not support these signals. Connecting an Out-of-Band Management Console If you wish to co

  • Compatible Systems MicroRouter 2270R, Appendix E - Terms and Conditions 43 ber of each item being returned; (c) original Compatible Systems Sales Agreement number; and (d) any special instructions. Upon receipt of this information, Compatible Systems will issue an RMA (“Return Material Authorization”) number and any required U.S. Customs identification to assure correct identification of the Customer and to insure prompt and accu- rate processing. 6. Limitation of Remedies. Compatible Systems’ liability for all claims brought pursuant to or in connection with this agreement, including the pur- ported breach hereof, shall be limited: (a) in the case of claims

  • Compatible Systems MicroRouter 2270R, Appendix E - Terms and Conditions 41 Appendix E - Terms and Conditions Compatible Systems Corporation (Compatible Systems) offers to sell only on the condition that Customer’s acceptance is expressly limited to Compat- ible Systems’ terms and conditions of sale. Compatible Systems’ accep- tance of any order from Customer is expressly made conditional on assent to these terms and conditions of sale unless otherwise specifically agreed to in writing by Compatible Systems. In the absence of such agreement, com- mencement of performance or delivery shall be for Customer’s convenience only and shall not be construed as an accep

  • Compatible Systems MicroRouter 2270R, i Chapter 1 - Introduction 1 ABOUT THE MICROROUTER 2270R 1 ANOTE ABOUT FIREWALLS 1 ANOTE ABOUT ON-DEMAND INTERNETWORKING 1 MICROROUTER 2270R INSTALLATION OVERVIEW 2 Chapter 2 - Getting Started 5 AFEW NOTES 5 PleaseRead The Manuals 5 Warranty andService 5 Getting Help With the MicroRouter 2270R 5 WHAT YOU WILL NEED TO GET STARTED 6 Supplied withthe MicroRouter 2270R 6 Needed For Installation 6 EthernetConnection Requirements 7 10Base-T Twisted-Pair Ethernet 7 T1 LineConnectionRequirements 7 Other Telco Line Connection Requirements 7 RS-232 Interface 8 Chapter 3 - Network Installation 9 Placing the Router 9 Connecting theRouter to the

  • Compatible Systems MicroRouter 2270R, 28 Chapter 6 - Basic Configuration Guide uses IARP (Inverse Address Resolution Protocol) to dynamically generate this information. To connect to other vendors’ routers which do not support IARP, you must provide DLCI-to-protocol mapping information. Note: Many Internet Service Providers (ISP’s) do not support IARP as a default. If one of your MicroRouter 2270R interfaces will be connected to an ISP via Frame Relay, check with your ISP technical staff on whether you must manually enter DLCI information or not. CV: Use the DLCI Mapping Database Dialog Box (under WAN/Link Configuration/DLCI button). TB: Use configure and set the DLCI keyword in the Frame Rel

  • Compatible Systems MicroRouter 2270R, Chapter 2 - Getting Started 5 Chapter 2 - Getting Started AFewNotes Please Read The Manuals The manuals included with your MicroRouter 2270R contain very important information about the MicroRouter 2270R and local and wide area networking in general. Please read this manual thoroughly, and refer to the management reference guides as required. It’s worth the few minutes it will take. Also, please fill out the warranty registration card and return it to us today. This will help us keep you informed of updates to the MicroRouter 2270R and future products available from Compatible Systems. You can also register on the web at http://www.compat- ible.

  • Compatible Systems MicroRouter 2270R, Chapter 6 - Basic Configuration Guide 21 Suggested for IPX You may want to set your own network numbers, rather than using the autoconfigured values. You may also want to turn off unused frame types. CV: Use the IPX Routing: Ethernet 0 Dialog Box. TB:Useconfigure and set keywords in the IPX Ethernet 0 (and/or Ethernet 1) section. AppleTalk Protocol Required for AppleTalk There are generally no required changes from the shipping Ethernet configuration for AppleTalk. The Ethernet interface will autoconfigure to use AppleTalk Phase 2, and will autoadapt to conditions on the Ethernet. Suggested for AppleTalk You may want

  • Compatible Systems MicroRouter 2270R, iv Appendix A - Shipping Defaults 33 Default Password 33 Ethernet Interfaces 33 IP RoutingDefaults 33 IP Bridging Defaults 33 IPX RoutingDefaults 33 IPX Bridging Defaults 33 AppleTalk Routing Defaults 33 AppleTalkBridging Defaults 33 DECnet Defaults 33 WAN Interfaces 34 IP Defaults 34 IPX Defaults 34 AppleTalk Defaults 34 DECnet Defaults 34 T1 CSU/DSU (WAN 0) Link& Physical Defaults 34 RS-232 (WAN 1) Link & Physical Defaults 34 Appendix B - Connector and Cable Pin Outs 35 Pin Outs for T1 Female Connector (DTE) 35 Pin Outs for DB-25 Male to DB-25 Female RS-232 Data & Console Cable 35 Appendix C - LED P

  • Appendix D - Downloading Software From Compatible Systems 39 Appendix D - Downloading Software From Compatible Systems We make the latest versions of operating software for all Compatible Systems products available at our Web site. The latest version of CompatiView management software is also available. To download software, follow the instructions below. 1. Use

  • Compatible Systems MicroRouter 2270R, Chapter 5 - Command Line Management 15 Chapter 5 - Command Line Management The command line interface allows you to configure and monitor the router in-band via Telnet or out-of-band with a terminal connected to the MicroRouter 2270R’s Console interface. Note: Proper syntax is vital to effective operation of command line management. Case is not significant – you may enter commands in upper case, lower case, or a combination of the two. Out-of-Band Command Line Management You can use command line management and text-based configuration out-of-band as a permanent management tool, or only temporarily in order to set the router’s IP pa

  • Compatible Systems MicroRouter 2270R, Chapter 1 - Introduction 3 The manual is divided into several sections that should provide you with all the information you will need to use the MicroRouter 2270R on your network. For the latest documentation on Compatible Systems products, including the most current version of this manual, visit the Technical Support section of our Web site at: http://www.compat- ible.com. Chapter 2 - Getting Started This part of the manual describes the contents of the MicroRouter 2270R package and emphasizes the preparation and equipment you will need to install the route

  • Compatible Systems MicroRouter 2270R, Appendix A - Shipping Defaults 33 Appendix A - Shipping Defaults Default Password •letmein Ethernet Interfaces IP Routing Defaults • Off, both interfaces IP Bridging Defaults • On, both interfaces • Address: 198.41.12.1 • Subnet Mask: 255.255.255.0 • Broadcast Address: 198.41.12.255 •IPRIPoff IPX Routing Defaults • 802.3 on, autoseeding, both interfaces • 802.2 on, autoseeding, both interfaces • Type II off, both interfaces • 802.2 SNAP off, both interfaces IPX Bridging Defaults • Off, both interfaces AppleTalk Routing Defaults •

  • 42 Appendix E - Terms and Conditions To obtain service under this Warranty, the Customer (or subsequent pur- chaser, if applicable) must follow the procedures outlined below, under “Product Return Policy.” THE WARRANTIES SET FORTH IN THESE TERMS AND CONDI- TIONS ARE IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED. WITHOUT LIMITATION ON THE GENERALITY OF THE FOREGOING SENTENCE, COM

  • Compatible Systems MicroRouter 2270R, 24 Chapter 6 - Basic Configuration Guide • Set to allow dial-in and/or dial-out CV: Use the Link Configuration: WAN 1. TB: Use configure and set the Mode, ConnectMode, DialIn and/or DialOut keywords in the Link Config WAN 1 section. Suggested for Dial-On-Demand Operation This mode of operation is only supported on the WAN 1 RS-232 inter- face. Outgoing dial-on-demand requires some additional information. • Create dial-out script • Set dialing method • Set dial-out script to be used • Set inactivity time CV: Use the Link Configuration: WAN 1 Dialog Box to set the dialing method and to select a c

  • 14 Chapter 4 - CompatiView Software Installation Run the auto-installation program (CV5x file) by double-clicking on it. The installation program will ask you to select (or create) a directory in which it should locate CompatiView and its associated files and data- base subdirectory. Once the installation is complete, double-click on the CompatiView icon to open the program. For further info

Related Products and Documents (Network Router):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Sony CDU625 Operation & user’s manual sony/cdu625-62S.pdf 30 Jan 2024 28 0.27 Mb
2 Epson Stylus Pro 4800 Portrait Edition Important information epson/stylus-pro-4800-portrait-edition-2TG.pdf 20 Mar 2023 2 0.08 Mb
3 Belkin YourType Quick install manual belkin/yourtype-OOH.pdf 21 Sep 2023 47
4 Lenovo ThinkPad X131e Operation & user’s manual lenovo/thinkpad-x131e-AO7.pdf 13 Feb 2024 160
5 Kurzweil PC3LE Musician's manual kurzweil/pc3le-6O7.pdf 20 Jun 2023 379
6 Nonin 9570 Operation & user’s manual nonin/9570-WM3.pdf 06 Jun 2023 17

Similar Resources:

  • Grizzly

    Benchtop Downdraft Table T10115

    (2 pages)
    Specifications     …
  • NETGEAR

    GSM7328S-200NAS

    (26 pages)
    Page 1 of 24 © 2005 by NETGEAR, Inc. All rights reserved. Trademarks © 2005 NETGEAR, Inc. NETGEAR ® , the Netgear Logo, the Gear Guy, and Everybody’s connecting are trademarks or registered trademark of Netgear, Inc. in the United States and/or other countries. Microsoft, Windows, and the Windows logo are trademarks, or registered trademarks of Micro …
  • Cisco

    10720 - Internet Router

    (202 pages)
    Americas HeadquartersCisco Systems, Inc.170 West Tasman DriveSan Jose, CA 95134-1706 USAhttp://www.cisco.comTel: 408 526-4000800 553-NETS (6387)Fax: 408 527-0883Cisco 10720 Internet Router Installation and Configuration GuideCustomer Order Number: DOC-7813062=Text Part Number: 78-13062-10 …
  • Cisco

    1401

    (8 pages)
    Quick Start GuideINSTALLING YOUR CISCO 1401 ROUTERUNPACK THE BOXINSTALL THE ROUTERVERIFY YOUR INSTALLATIONCisco 1401HubPCPCInternetADSL connectionDSL modemPCPCPCPCServerServer123 …
  • ANTAIRA

    LNP-C500G-T

    (17 pages)
    Antaira Technologies LNP-C500G Series User Manual V1.0 i LNP-C500G Series Compact 5-Port Industrial Gigabit PoE+ Unmanaged Ethernet Switch, w/4*10/100/1000Tx (PSE: 30W/Port) + 1*10/100/1000Tx Version 1.0 (October 2017) User Manual …
  • Alfa Network

    AIP-W525H V2

    (8 pages)
    Presented by Peter Spani www.PcXpert.org You can use, distribute, print this document, but do not modify it or put your signature! Before you begin, read the entire document. Alfa AIP-W525H_V2 Router mode setup Connect the AIP-W525H to a power source; connect a network cable to one of the LAN ports and the other end to your Computer Open any intern …

Network Router Instructions:

Comments, Questions and Opinions: