Manualios.com

Crest Audio X-RACK XRM Owner's Manual

Crest Audio X-RACK XRM Manual Online:

3.65, 2824 votes
Crest Audio X-RACK XRM User Manual
Crest Audio X-RACK XRM User Guide
Crest Audio X-RACK XRM Online Manual

Text of Crest Audio X-RACK XRM User Guide:

  • Crest Audio X-RACK XRM, p.41 Specifications 4 Specifications Frequency response +0/-0.5dB 20Hz-20kHz ref 1kHz (any input to any output) THD+noise any output <0.01% THD 20Hz-20kHz@ +15dBu out Noise mic ein: better than –128dBu 20Hz to 20kHz 150 ohm source, 60dB gain Bus Noise: better than -85dBu Crosstalk/Shutoff All Crosstalk measurements: 20Hz to 20kHz BW Channel Mute >90dB Channel Fader attenuation >90dB Mix Send attenuation >85dB Phase Shift < +/- 30 degrees, 20Hz to 20kHz – mic-in to mix out XLR In F-XLR 4k ohm balanced max voltage gain to mix outs = 92dB Split Out M- XLR 4k ohm balanced Passive “Y-Split” of XLR In Line-in TRS >10k Ohms balanced XLR/TRS Com Input >10

  • Crest Audio X-RACK XRM, Front panel features Channel Level and Control This next set of controls allows the operator to control and monitor the overall level of the channel signal. Mute Sw and LED The Mute switch kills the channel signal and prevents it from feeding any Mix Send pots.The mute- element itself is a FET transistor, allowing for timed, ramped on-off control of the channel signal.This avoids any “pops and clicks” when muting a channel. Normally, the Mute will also affect the PRE signals of the channel (see Mix Send details). PRE can be selected for Mix Sends 1 thru 4, and is normally

  • Crest Audio X-RACK XRM, p.26 Stereo input channel 2 XRM owner’s manual PUSHPUSHPUSHPUSHPUSHPUSHPUSHPUSHPUSHPUSHPUSHPUSHPUSH PUSH PUSH PUSH PUSH PUSH PUSH PUSH S4 S3 S2 S1 L R Input L R Split Out +48V On Chan Insert 1 XLRs Pin1 Lift Split Out Balanced Line Inputs For Stereo Channels S1 – S4 +48V On Balanced Input 1 +48V On Chan Insert 2 XLRs Pin1 Lift Split Out Balanced Input 2 +48V On Chan Insert 3 XLRs Pin1 Lift Split Out Balanced Input 3 +48V On Chan Insert 4 XLRs Pin1 Lift Split Out Balanced Input 4 +48V On Chan Insert 5 XLRs Pin1 Lift Split Out Balanced Input 5 +48V On Chan Insert 6 XLRs Pin1 Lift Split Out Balanced Input 6 +48V On Chan Insert 7 XLRs Pin1 Lift Split Out Balanced Inpu

  • Front panel features The XRM master section contains the controls and indicators for the Solo system, headphone and Monitor system, and Mix Master outputs.This section allows the operator to control the overall operation of the mixer. A BNC lamp connector, supplied with +12 volts, is also located within this section. Each individual sub-system will be describe

  • Crest Audio X-RACK XRM, Front panel features Stereo EQ The Stereo Input channel has two parallel EQ circuits that are controlled by the same set of knobs. It is functionally identical to the Mono Input EQ. Many audio signals coming into the console require some degree of corrective eq in order to be part of a good sounding mix. XRM offers a 4-Band EQ on each channel.The input EQ consists of the bands: High, High-Mid, Low-Mid and Low.The High and Low frequency bands are shelving equalizers, each have a boost/cut control and their frequencies are fixed.The High-Mid and Low- Mid bands have a bell-shaped response, each band features variable boost/cut and adjustable fre- quency. high frequency—HF Boost / Cu

  • Crest Audio X-RACK XRM, p.16 Mono input channel 1 XRM owner’s manual PUSHPUSHPUSHPUSHPUSHPUSHPUSHPUSHPUSHPUSHPUSHPUSHPUSH PUSH PUSH PUSH PUSH PUSH PUSH PUSH S4 S3 S2 S1 L R Input L R Split Out +48V On Chan Insert 1 XLRs Pin1 Lift Split Out Balanced Line Inputs For Stereo Channels S1 – S4 +48V On Balanced Input 1 +48V On Chan Insert 2 XLRs Pin1 Lift Split Out Balanced Input 2 +48V On Chan Insert 3 XLRs Pin1 Lift Split Out Balanced Input 3 +48V On Chan Insert 4 XLRs Pin1 Lift Split Out Balanced Input 4 +48V On Chan Insert 5 XLRs Pin1 Lift Split Out Balanced Input 5 +48V On Chan Insert 6 XLRs Pin1 Lift Split Out Balanced

  • Crest Audio X-RACK XRM, p.10 Mono input channel 1 XRM owner’s manual 500500500500500500500500500500500 4 2 3 2 3 6 0 1 3 0 500 2 3 2 3 2 3 2 3 2 3 2 3 4 2 3 4 2 3 4 2 3 4 2 3 4 2 3 PFL 40 20 10 0 6 • 3 30 + – 40 20 10 0 10 • 5 30 + – CHAN LE VEL 0 1515 88 +– 0 1515 88 +– 0 1515 88 +– 0 1515 88 +– LM LF HF HM EQ ON 1 600 1K 2K 3K 8K 400 5K 300 500 1K 2K 100 MIX SENDS 40 20 10 0 6 • 3 30 + – 40 20 10 0 6 • 3 30 + – 40 20 10 0 6 • 3 30 + – 40 20 10 0 6 • 3 30 + – 40 20 10 0 6 • 3 30 + – 40 20 10 0 6 •

  • Crest Audio X-RACK XRM, p.36 Master section 3 XRM owner’s manual Monitor Out Common Input to All Mixes Left (Odd) Right (Even) Controlled by SPEAKER-ON Switch ( Level Control on Front Panel ) Left (Odd) Right (Even) MONITOR OUT - L MONITOR / HP LEVEL L R HEADPHONE AMP SOLO LEFT SOLO MIX AMPS SOLO DC SOLO FEED L - R SOLO CONTROL LOGIC +9 6 3 0 -3 6 9 12 15 18 21 24 SOLO ON PWR ON LED METERS FOLLOW SOLO SOLO RIGHT SPEAKER ON MONITOR OUT - R COMMON INPUT - L COMMON INPUT LEVEL ODD MIX BUSES 1 3 5 7 9 11 2 4 6 8 10 12 EVEN MIX BUSES L R S

  • Crest Audio X-RACK XRM, Front panel features Line Input (Mic Pad) With this switch in the UP position, the input preamp circuit is set up to accept a mic-level signal. This signal is brought in via the XLR mic-input connector located on the rear panel.The 1/4" TRS input jack is ignored. When the switch is depressed, a Pad is inserted into the signal path and the input preamp circuit is set up to accept a line-level signal from either the XLR mic-input connector or the 1/4" TRS input jack, both located on the rear panel.The XLR signal is normal'd to the 1/4” TRS jack. If nothing is plugged into the TRS jack, the XLR signal is fed to the preamp when the LINE switch is pressed. Sin

  • Crest Audio X-RACK XRM, p.38 Master section 3 XRM owner’s manual SOLO LINK IN OUT Use 5-Pin DIN cable to interconnect SOLO Systems of X-Rack Mixers ON P O W E R AC IN 100 - 240V 50 / 60 Hz 80W X-RACK RACK-MOUNT MIXER NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL AVIS : RISQUE DE CHOC ÉLECTRIQUE—NE PAS OUVRIR ATTENTION! POUR ÉVITER LE RISQUE D'INCENDIE OU DE CHOC ÉLECTRIQUE, NE PLACEZ PAS CET APPAREIL SOUS LA PLUIE OU Á L'HUMIDITÉ CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE M

  • Crest Audio X-RACK XRM, Master section 3 p.28 XRM owner’s manual LAMP 12V SOLO PWR LR 5 10 0 5 10 20 30 SIG PK 9 AFL 10 11 12 OUTPUT MASTERS SPEAKERS ON COMMON INPUT P H O N E S 1 3 5 7 10 0 9 28 6 4 M F F M 500 N ) 1 3 5 7 10 0 9 28 6 4 LEV LEV 0 9 6 12 3 6 9 3 15 24 18 21 500 9 – 10 11 – 12 5 10 0 5 10 20 30 SIG PK 5 AFL 678 OUTPUT MASTERS 5 – 67 – 8 5 10 0 5 10 20 30 SIG PK 1 AFL 234 OUTPUT MASTERS STR PAIR LO CUT STR PAIR LO CUT 1 – 23 – 4 XR STR PAIR LO CUT STR PAIR LO CUT STR PAIR LO CUT STR PAIR LO CUT 500500500500500500500500500500500 500500500

  • Crest Audio X-RACK XRM, Mono input channel 1 p.6 XRM owner’s manual 500500500500500500500500500500500 6 500 PFL 40 20 10 0 6 • 3 30 + – 40 20 10 0 10 • 5 30 + – CHAN LE VEL 0 1515 88 +– 0 1515 88 +– 0 1515 88 +– 0 1515 88 +– LM LF HF HM EQ ON 1 600 1K 2K 3K 8K 400 5K 300 500 1K 2K 100 MIX SENDS 40 20 10 0 6 • 3 30 + – 40 20 10 0 6 • 3 30 + – 40 20 10 0 6 • 3 30 + – 40 20 10 0 6 • 3 30 + – 40 20 10 0 6 • 3 30 + – 40 20 10 0 6 • 3 30 + – 40 20 10 0 6 • 3 30 + – 40 20 10 0 6 • 3 30 + – 40 20 10 0 6 • 3 30 + – 40 20 10 0 6 • 3 30 + – 40 20 10 0 6 • 3

  • Crest Audio X-RACK XRM, p.12 Mono input channel 1 XRM owner’s manual 500500500500500500500500500500500500 PFL 40 20 10 0 6 • 3 30 + – 40 20 10 0 10 • 5 30 + – CHAN LE VEL 0 1515 88 +– 0 1515 88 +– 0 1515 88 +– 0 1515 88 +– LM LF HF HM EQ ON 1 600 1K 2K 3K 8K 400 5K 300 500 1K 2K 100 MIX SENDS 40 20 10 0 6 • 3 30 + – 40 20 10 0 6 • 3 30 + – 40 20 10 0 6 • 3 30 + – 40 20 10 0 6 • 3 30 + – 40 20 10 0 6 • 3 30 + – 40 20 10 0 6 • 3 30 + – 40 20 10 0 6 • 3 30 + – 40 20 10 0 6 • 3 30 + – 40 20 10 0 6 • 3 30 + – 40 20 10

  • Crest Audio X-RACK XRM, Master section 3 p.32 XRM owner’s manual LAMP 12V SOLO PWR LR 5 10 0 5 10 20 30 SIG PK 9 AFL 10 11 12 OUTPUT MASTERS SPEAKERS ON COMMON INPUT P H O N E S 1 3 5 7 10 0 9 28 6 4 M F F M 500 N ) 1 3 5 7 10 0 9 28 6 4 LEV LEV 0 9 6 12 3 6 9 3 15 24 18 21 500 9 – 10 11 – 12 5 10 0 5 10 20 30 SIG PK 5 AFL 678 OUTPUT MASTERS 5 – 67 – 8 5 10 0 5 10 20 30 SIG PK 1 AFL 234 OUTPUT MASTERS STR PAIR LO CUT STR PAIR LO CUT 1 – 23 – 4 XR STR PAIR LO CUT STR PAIR LO CUT STR PAIR LO CUT STR PAIR LO CUT 500500500500500500500500500500500 500500500 2

  • Crest Audio X-RACK XRM, Front panel features Equalizer (EQ) Many audio signals coming into the console require some degree of corrective eq in order to be part of a good sounding mix. XRM offers a 4-Band EQ on each channel.The input EQ consists of the bands: High, High-Mid, Low-Mid and Low.The High and Low frequency bands are shelving equalizers, each have a boost/cut control and their frequencies are fixed.The High-Mid and Low- Mid bands have a bell-shaped response, each band features variable boost/cut and adjustable fre-

  • Crest Audio X-RACK XRM, 1 Save the carton and packing materials! Should you ever need to ship the unit, use only the original factory packing. For replacement packaging, call Crest Audio’s Customer Service Department directly. 2 Read all documentation before operating your equipment. Retain all documentation for future reference. 3 Follow all instructions printed on unit chassis for proper operation. 4 Do not use the unit if the electrical power cord is frayed or broken. The power supply cord should be rout- ed so that it is not likely to be walked on or pinched by items placed upon or against it. 5 Alwa

  • Crest Audio X-RACK XRM, Stereo input channel 2 p.18 XRM owner’s manual 500 M F F M 500500500500500500500500500500500500 500 2 3 2 3 6 0 3 500 2 3 2 3 2 3 2 3 2 3 2 3 2 3 2 3 2 3 2 3 2 3 PFL 40 20 10 0 6 • 3 30 + – 40 20 10 0 10 • 5 30 + – CHAN LE VEL 0 1515 88 +– 0 1515 88 +– 0 1515 88 +– 0 1515 88 +– LM LF HF HM EQ ON S1 600 1K 2K 3K 8K 400 5K 300 500 1K 2K 100 SUM INPUTS STR LINE IN ( MIC PAD ) 20 15 40 60 35 MIX SENDS 40 20 10 0 6 • 3 30 + – 40 20 10 0 6 • 3 30 + – 40 20 10 0 6 • 3 30 + – 40 20 10 0 6 • 3 30 + – 40 20 10 0 6 • 3 30 + – 40 20 10 0 6 • 3 30 + – 40 20 10 0 6 • 3 30 + – 40 20 10 0 6 • 3 30 + – 40 20 10 0 6

  • Crest Audio X-RACK XRM, p.17 Mono Input channel 1 Rear panel features (continued): Split-Out XLR jack This male XLR jack is wired pin-to-pin to the female XLR input jack. In combination with the female XLR, it forms a passive,Y-Split of the input signal.This split-signal can be used to feed the mic input to another mixer (usually the FOH mixer), or to “mult” the input to another chan- nel on the XRM. NOTE: This pin-to-pin connection between XLR jacks is NOT affected by the Pin-1 lift switch. Chan Insert jack This switching 1/4” TRS jack allows an ext

  • Crest Audio X-RACK XRM, p.14 Mono input channel 1 XRM owner’s manual PUSHPUSHPUSHPUSHPUSHPUSHPUSHPUSHPUSHPUSHPUSHPUSHPUSH PUSH PUSH PUSH PUSH PUSH PUSH PUSH S4 S3 S2 S1 L R Input L R Split Out +48V On Chan Insert 1 XLRs Pin1 Lift Split Out Balanced Line Inputs For Stereo Channels S1 – S4 +48V On Balanced Input 1 +48V On Chan Insert 2 XLRs Pin1 Lift Split Out Balanced Input 2 +48V On Chan Insert 3 XLRs Pin1 Lift Split Out Balanced Input 3 +48V On Chan Insert 4 XLRs Pin1 Lift Split Out Balanced Input 4 +48V On Chan Insert 5 XLRs Pin1 Lift Split Out Balanced Input 5 +48V On Chan Insert 6 XLRs Pin1 Lift Spli

  • Crest Audio X-RACK XRM, Front panel features Channel Level and Control This next set of controls allows the operator to control and monitor the overall level of the channel signal. Both sides of the Stereo channel (left & right) are simultaneously controlled. Mute Sw and LED The Mute switch kills the channel signals and prevents it from feeding any Mix Send pots.The mute- element itself is a FET transistor, allowing for timed, ramped on-off control of the channel signal.This avoids any “pops and clicks” when muting a channel. Normally, the Mute will also affect the PRE signals of the channel (see Mix Send details). PRE can be selected for Mix Sends 1 thru 4, a

  • Front panel features The XRM features four, full-function Stereo Input channels.These inputs are labeled S1 thru S4 and are located directly left of the master section. Each stereo channel features two mic preamps, so mic-level stereo sources can be processed on one common channel. In cases where just a mono source is present, the SUM INPUTS switch allows a mono source (plugged into eith

  • Crest Audio X-RACK XRM, Front panel features Mix Send features The XRM is capable of generating 12 mono mixes, 6 stereo mixes, or a combination of both mono and stereo mixes. Each of the six Odd/Even pairs of sends can be configured as a stereo pair- the Odd pot becomes the level control, the Even pot becomes the pan pot.The changeover to stereo operation is controlled by the STR PAIR switches located above the master faders.A LO CUT switch is also present for activating the hi-pass filter (40Hz, -18dB/oct) for each pair of mixes. Mix 1 - 4 PRE MIX Sends 1-4 are Post-Fader MIX Sends 1-4 are Pre-Fader Normally, the signal feeding the Mix Sends is derived after the main Chan Level Pot (Post-Fader). This

  • p.37 Master section 3 Rear panel features (continued) Other Inputs and Outputs Common Input A stereo input is provided for feeding a common signal to all of the 12 mix buses simultane- ously. From the stereo source, the left signal will feed all of the odd mixes, the right signal will feed all of the even mixes. Both XLR and 1/4” TRS jacks are provided, the

  • Crest Audio X-RACK XRM, 4 1 2 3 Master section P .29 Solo and Monitoring System, Output Masters. Front panel controls and rear panel connectors. Stereo Input channels p.19 Front panel controls and rear panel connections Mono Input channels p. 7 Front panel controls and rear panel connections table of contents Introduction Thank you and congratulations on your purchase of your new Crest Audio X-Rack mixer.We’re confident that you will enjoy many years of trouble-free service from it.You will quickly find that it fits into a wide variety of mixing a

  • Crest Audio X-RACK XRM, XRM owner’s manual p.4 XRM block diagram BAL XLR IN BAL LINE IN INPUT PREAMP GAIN 10 - 70 dB FOUR BAND EQ LEVEL LF LOW MID HI MID HF HPF LINE (MIC PAD) 26dB PA D PRE-SOURCE SELECT PRE SOURCE MUTE ? SOLO DC +10 MUTE INSERT SEND / RTN +48V ON EQ ON FADER AMP PRE-SOURCE BUFFER NO YES SOLO LEFT MAIN RIBBON CABLE - 40 WAY XRM MONO INPUT MODULE 12 MONO INPUTS AVAILABLE HPF 70Hz -18dB/Oct FREQ INPUT SIGNAL LED PRE FADER POST FADER LEVEL LEVELFREQ LEVEL SOLO RIGHT 12 KHZ400 - 8 KHZ80 - 2 KHZ80 HZ XRM BLK DIA-REV1.0 - 5/20/02 PFL SOLO TRIGGER CHAN FADER MIX 1-4 PRE PRE FADER PRE EQ PRE INSERT

  • Master section 3 p.30 XRM owner’s manual Block diagram- Common Input Module Block diagram- Mix Outputs AIN B BON A BLE - WAY ODD MIX BAL OUT MIX INSERT SEND / RTN XRM MIX PAIR 1 OF 6 PAIRS SHOWN ODD MIX AMP +10 PEAK (AFL) SIG SIG/PK LED POST FADER ODD FADER 60MM PRE FADER ODD MIX BUS IN SOLO DC SOLO LEFT SOLO RIGHT AFL-ODD G R HPF HPF 40Hz -18dB/Oct

  • Crest Audio X-RACK XRM, p.39 Master section 3 Rear panel features (continued) Solo Link When using multiple X-Rack mixers together, the solo systems can be linked.This Solo Link is compatible with the XR-20 and XR-24 Rack mixers. A 5-pin, shielded DIN cable, wired pin-to- pin, can be used to link the Solo Audio and control signals between mixers.The “Slave” mixer has its own solo’d signals appear in its own solo system, but these signals are also passed to the “Master” mixer where they also show up in the Master mixer solo system, added to any existing solo’d signals, or triggering the Master solo if nothing else was present.The Master and Slave consoles are de

More Instructions:

DOWNLOAD

Related Products and Documents (Monitor):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 TVLogic VFM-056W Operation manual tvlogic/vfm-056w-9DK.pdf 26 Jul 2023 32
2 Frigidaire FES367F Factory parts catalog frigidaire/fes367f-E1N.pdf 13 Aug 2023 12
3 Casual Living AQUA Assembly instructions casual-living/aqua-213.pdf 17 Mar 2023 5
4 ILVE UP60 User instructions, installation, maintenance ilve/up60-N2U.pdf 02 Feb 2023 48
5 Philips 579873116 Brochure philips/579873116-J9O.pdf 07 Dec 2023 3 1.52 Mb
6 Element-Hz ELE9090 Installation manual element-hz/ele9090-X97.pdf 14 Sep 2023 15

Similar Resources:

  • TANDBERG

    0100400003AA

    (23 pages)
    User’s Manual 52” Dual Color TFT LCD Monitor Model Name : FS-S5202C Model Number : 0100400003AA Customer Project name : Aquarius Dual TANDBERG Page 1 of Item number : Item name : 117336 TANDBERG Monitor Dual 52” Assembly Rev.:01-draft Date Sign Changes : Rev 01 Init Tech App First build of the specification Vendor Ve …
  • NEC

    AccuSync Series

    (2 pages)
    www.necdisplay.comBusiness DesktopNEC AccuSyncTM Series 15" - 22" flat-panel monitors ideal for small-to-medium businesses High-quality LCD monitors don’t necessarily have to be associated with high-end price tags. NEC AccuSync Series monitors have set a new standard in value for the flat-panel monitor category, offering you a perfect opportu …
  • Philips

    170P5ES

    (2 pages)
    17 inch LCD Monitor 17 inch LCD Monitorthe best productivity solution the best productivity solution 170P5ESPicture/ DisplayCommercial Specifications• LCD Panel Type 1280 x 1024 pixels, Anti-glare Polarizer, RGB Vertical Stripe• Panel Size 17"/ 43cm• Effective Viewing Area 337.9 x 270.3 mm• Pixel Pitch 0.264 x 0.264 mm• Br …
  • Samsung

    T27B350ND

    (43 pages)
    MONITOR y TV LED(MFM TV)manual del usuarioGracias por adquirir este producto de Samsung. Para obtener un servicio más completo, registre su producto enwww.samsung.com/registerModelo: _____________ N.º de serie: _____________TB300TB350 ✎Si tiene alguna pregunta, llámenos al 1-800-SAMSUNG (1-800-726-7864) para obtener ayuda. …
  • LG

    Flatron T711B

    (43 pages)
    COLOR MONITORSERVICE MANUALWebsite:http://biz.LGservice.comE-mail:http://www.LGEservice.com/techsup.htmlCAUTIONBEFORE SERVICING THE UNIT, READ THE SAFETY PRECAUTIONS IN THIS MANUAL.MENU SELECTBrightviewMODEL: T711B (T711BL-AL**E)CHASSIS NO. : CA-136T711S (T711BL-AL**M)( ) **Same model for Service*Same looking with new chassis.Issue Date; 2004. 7. …
  • LG

    W2042TQ

    (1 pages)
    W2042TQSIZE20” WideRESOLUTION 1680x1050CONTRAST RATIO8000:1 (DFC)EXPAND YOUR VIEW Increase your productivity with increased screen real estate. Work on a spreadsheet, browse the web, and watch a movie on one screen with room to spare.20” Wide Format LCD Monitor Pixel Pitch0.258 x 0.258Viewing Angle170°/170°Sync RangeHorizontal Frequency30 ~ 8 …

Comments, Questions and Opinions: