CyberPower PowerPanel Operation & User’s Manual

Text of CyberPower PowerPanel User Guide:

• CyberPower PowerPanel, TABLE OF CONTENTS INTRODUCTION…………………………………...………………… 1 INSTALLATION GUIDE…………………………………...………… 4 CONFIGURATION GUIDE…………………...………………...…… 7 Monitoring…………………………………………………………. 7 Current Status..………………………………………………… 7 UPS Information...………………..……………………………. 8 Control….……………………………………�

• CyberPower PowerPanel, CyberPower Network Management System 1 INTRODUCTION Overview The CyberPower Network Management Card is an external card that allows remote monitoring and control of a UPS on a network. After installing the hardware and configuring an IP address, the user can access, monitor and control the UPS from anywhere in the world! No software installation is needed. Simply use a web browser such as Internet Explorer or FireFox to access your UPS. Servers and workstations protected by the UPS can be installed with PowerPanel Shutdown Service software to utilize the additional remote shutdown features of the Network Management Card.

• CyberPower PowerPanel, CyberPower Network Management System 2 Unpacking Inspect the Network Management Card upon receipt. The package should contain the following: z CyberPower Network Management Card z PowerPanel TM Shutdown Service Software and user manuals CD z AC adapter ( For select UPS models only )

• CyberPower Network Management System 3 z Description 1) Serial Port provides a connection for communication between the UPS and the Network Management Card 2) Reset Button is used to reset the settings. When the Reset Button is pushed for 3 seconds, all settings except for the IP address for Network Management Card will refre

• CyberPower PowerPanel, CyberPower Network Management System 4 INSTALLATION GUIDE Step 1. Hardware Installation 1. Connect the Ethernet cable to the LAN port of the CyberPower Network Management Card. 2. Connect the CyberPower Network Management Card to the UPS communication port. It is optional to use the serial cable included. 3. Connect the supplied AC adapter to the Network Management Card Adapter and plug into the wall socket. (For selected UPS models only). 4. After the above procedures are done, press and hold the Reset Button on the Network Management Card for 7 seconds to ensure the IP Address is at the default value. Step 2. Configure the IP address

• CyberPower PowerPanel, CyberPower Network Management System 5 Figure 2. The SNMP card setting window. 6. First, choose either IP or MAC address from the device address option. 7. Then click on each checkbox to modify the IP, subnet mask or gateway address. Enter the new addresses into the corresponding fields. 8. You will need to input password for the SNMP card (Figure 3) in the authentication window, as shown in figure 3. *Default User name: cyber; Default Password: cyber Fig

• CyberPower Network Management System 6 Figure 4. Setup IP Address successfully message. Method 2 : Use DOS Mode Setting 1. Obtain the MAC address indicated on the label of the Network Management Card rear panel. (Each Management Card has a unique MAC address). 2. Use the ARP commend to set you IP address. For example, to as

• CyberPower PowerPanel, CyberPower Network Management System 7 CONFIGURATION GUIDE [Monitoring] menu contains [Current Status] page and [UPS Information] page [Current Status] displays basic information of UPS current status. Status Field Definition Input Line Voltage Shows the current input voltage of the utility power Output Frequency Displays the frequency of the utility power Maximum Line Voltage Identifies the highest voltage of the utility power input to the UPS during the previous minute of operation. Minimum Line Vo

• CyberPower PowerPanel, CyberPower Network Management System 8 [UPS Information] provides the technical specifications of your UPS. Information Description Model Name Displays the UPS’s model number Voltage Rating Identifies the current AC voltage to the UPS. Working Frequency Displays the current frequency of the UPS. Power Rating Displays the capacity of the UPS in VA. Load Power Identifies the capacity of the UPS in Watts. Battery Voltage Rating Displays the DC voltage of the battery. Firmware Ve

• CyberPower PowerPanel, CyberPower Network Management System 9 [Control] menu contains [UPS Control] page, [UPS Reboot] page, and [UPS Schedule] page. [UPS Control] allows basic remote control of the UPS. Select one test by clicking the button on the left of the command. Click [Apply] to run the test. Click [Cancel] to stop any command that has been selected. Please Note: If the UPS is shut OFF, the following commands will not work. The Network Management Card will display the message: “Command fails. UPS is turned off.” Commands Definition Auto Diagnostics To diagnose that the UPS can function well under Bat

• CyberPower PowerPanel, CyberPower Network Management System 10 [UPS Reboot] allows advanced remote control of the UPS. Select one function by clicking its button. Click [Apply] to begin the operation. Select [Cancel] to refresh the selection. Note: The commands in [UPS Reboot] menu may change by the settings in the [UPS Schedule] menu. Commands Definition Reboot UPS Immediately To turn the UPS off and then on again. Delay 03 min(s) to Reboot UPS 3 minutes is a default value. The user may select any number between 1-99. The UPS will shut off and wait the set amount of time before turning back on. Cancel Reboot UPS To stop the previous

• CyberPower PowerPanel, CyberPower Network Management System 11 [UPS Schedule]: Sets the UPS to automatically shutdown and restart at consistent times - weekly or daily. [Special Shutdown]: The user may set a specific date and time for UPS shutdown. [Weekly]: Set a specific day and time of the week for UPS shutdown. [Daily]: Set a specific time of the day for UPS shutdown. 1. Click [Special], [Daily] or [Weekly] scheduled shutdown features to enter each setup menu. 2. Enter the

• CyberPower Network Management System 15 1. Input the receivers IP address. This address will identify the receiver of traps. The default value 0.0.0.0 or 255.255.255.255 defines all NMS as receivers. 2. Input the community (functioned as password, maximum of 15 characters). 3. Select one option [Enable] or [Disable]. 4. Click [Apply] to activate the s

• CyberPower PowerPanel, CyberPower Network Management System 16 Information indicates an event that requires no action. Warning indicates an event that does not require immediate attention, but this condition should be monitored. Severe indicates an event that requires immediate attention. 1. Determine the severity levels and click the option buttons. 2. Click [Apply] to activate the settings. [UPS Shutdown]: Configures UPS shutdown and PC safe shutdown times. 1. Low-Battery Duration: Time from a Low-Battery signal until load is shutdown. 2. Maximum Shutdown Time: The maximum time the UPS will wait before it shuts down in

• CyberPower PowerPanel, CyberPower Network Management System 18 Appendix 1 IP Address Settings of CyberPower Network Management Card Overview All devices on a computer network need to have an IP address. Each device’s IP address is unique. The same address cannot be used twice. In order to assign an IP address to the CyberPower Network Management Card, first, you must determine the range of the available IP addresses, and then choose an unused IP address to assign to the Network Management Card. PLEASE NOTE: You may need to contact your network administrator to obtain an available IP address. Procedures to f

• CyberPower PowerPanel, CyberPower Network Management System 19 If the response is shown as below, the IP address is in use. Try another IP address until an available address is found. Pinging 192.168.20.240 with 32 bytes of data: Reply from 192.168.20.240: bytes=32 time<10ms TTL=64 Reply from 192.168.20.240: bytes=32 time<10ms TTL=64 Reply from 192.168.20.240: bytes=32 time<10ms TTL=64 Reply from 192.168.20.240: bytes=32 time<10ms TTL=64

More Instructions:

	CyberPower PowerPanel Installation manual 02-09-2023 21	DOWNLOAD
	CyberPower PowerPanel Operation & user’s manual 15-07-2023 81	DOWNLOAD
	CyberPower PowerPanel Operation & user’s manual 13-08-2022 37	DOWNLOAD
	CyberPower PowerPanel Installation manual 12-12-2022 21	DOWNLOAD

Related Products and Documents (Network Card):

Comparable Devices:

Similar Resources:

• Asus WL-138G (51 pages) ContentEnglish ................................................................. 1Français ............................................................... 6Deutsch ............................................................. 11Русский ............................................................... 16Español.......................................... …

• CyberPower RMCARD202 (33 pages) User’s Manual Remote Management Card RMCARD202/RMCARD203 RMCARD302/RMCARD303 Intelligent Remote Management Card allows a UPS system/environment sensor to be managed, monitored, and configured Version 1.6 …

• Moxa Technologies Moxa Smartio C168H (74 pages) SSmmaarrttiioo C168H/PCI User’s ManualSmartio 8 Ports Serial Board for PCI BusJul. 1999 (2nd Edition)The content of this manual is also available in CD-ROM and at Moxa Web Site.Moxa Technologies Co., Ltd.Tel: +866-2-8665-6373Fax: [email protected] …

• Silicon Laboratories Network Card (40 pages) Rev. 0.6 1/11 Copyright © 2011 by Silicon Laboratories Ethernet-DKEthernet-DKEMBEDDED ETHERNET DEVELOPMENT KIT USER’S GUIDE1. OverviewThe Embedded Ethernet Development Kit (Ethernet-DK) provides all the hardware and software required todevelop real-world embedded Ethernet applications using the industry proven CMX Micronet™ protocol stack andhigh-perfo …

• Sanyo PJ-Net Organizer Plus POA-PN02 (114 pages) OWNER’S MANUALThis PJ-Net Organizer is an optional network productfor the projector. Mount this product to the projectorand connect a network cable. It enables a projector todisplay the image data stored in the file server and thescreen image of the computer via the network. In addi-tion, you can control and set up the projector remotelyby using the web br …

• CH Tech AM105 (1 pages) C&H Technologies, Inc. • 445 Round Rock West Drive • Round Rock, TX 78681-5012(512) 733-2621 • FAX (512) 733-2629 • www.chtech.com Ordering InformationDescriptionAM105 M-Module Extender BoardPart NumberAM105 11028421-0001AM105 M-Module Extender Board:The M-Mod u le Ex te nder bo ard eases the M-Mo dul edev elop me n t cycle …

Comments, Questions and Opinions: