Manualios.com

D-Link DSN-5210-10 - xStack Storage Area Network Array Hard Drive Hardware Reference Manual

  • DSN-5210-10 - xStack Storage Area Network Array Hard Drive Carrying Case
  • map/jXDowIocg
  • Hardware Reference Manual
  • PDF / Adobe Acrobat Reader
  • 52

D-Link DSN-5210-10 - xStack Storage Area Network Array Hard Drive Manual Online:

3.45, 718 votes
D-Link DSN-5210-10 - xStack Storage Area Network Array Hard Drive User Manual
D-Link DSN-5210-10 - xStack Storage Area Network Array Hard Drive User Guide
D-Link DSN-5210-10 - xStack Storage Area Network Array Hard Drive Online Manual

Text of D-Link DSN-5210-10 - xStack Storage Area Network Array Hard Drive User Guide:

  • D-Link DSN-5210-10 - xStack Storage Area Network Array Hard Drive, DSN-5000 series Hardware Reference Guide 25 Chapter 4 DSN-5000-10 Expansion Array Layout and Installation This chapter describes the hardware components and installation instructions for the DSN-5000-10 Expansion Array. The topics covered in this chapter are:  Section 4.1, Expansion Array Front Panel Components  Section 4.2, Expansion Array Rear Panel Components  Section 4.3, Site, Safety, and Rack-Mount Considerations  Section 4.4, Unpacking the DSN-5000-10 Expansion Array  Section 4.5, Items Supplied by the User  Section 4.6, Installing the DSN-5000-10 Expansion Array  Section 4.7, Connecting DSN-5000-10 Expansion Arrays t

  • D-Link DSN-5210-10 - xStack Storage Area Network Array Hard Drive, 24 Chapter 3 Installing the DSN-5000 Series Primary Array 3.7 Connecting the Power Cords The DSN-5000 series primary array has two power receptacles. Both must be used to connect the DSN-5000 series primary array to an AC outlet: 1. Plug the female end of one power cord into one of the 3-pronged power connectors on the back of the DSN-5000 series primary array. Plug the other end of the power cord into a working AC outlet that is not controlled by a wall switch. 2. Repeat the previous step using the second power cable and power receptacle on the DSN-5000 series primary array. For best results, the second power receptacle should be on a different circuit.

  • D-Link DSN-5210-10 - xStack Storage Area Network Array Hard Drive, 6 Chapter 1 Introduction 1.3 System Overview Figure 1-1 shows a typical DSN-5000 series storage system (primary array DSN-5110-10, DSN-5210-10 or DSN-5410-10) configuration in a Storage Area Network (SAN). The SAN shown is an Ethernet network used solely for exchanging data between the customer's host servers and the DSN-5000 series storage system. The Ethernet bandwidth used by the servers exchanging data with the DSN- 5000 series storage system can be very high. Using a separate Ethernet network to act as a SAN keeps that data from interfering with the customer's existing LAN and improves security. Figure 1-1. Example of a DSN-5000 series Storage System Configura

  • D-Link DSN-5210-10 - xStack Storage Area Network Array Hard Drive, DSN-5000 series Hardware Reference Guide 41 Appendix B Installing the System in a Rack This appendix describes how to install the DSN-5000 series primary and DSN-5000-10 expansion arrays in a rack. The rack-mount kit comes with the following items:  Two long main left and right rails  Two medium left and right rear rails  Two short left and right rear rails  Ten long screws and four short screws  Ten spring-loaded cage nuts  Ten E-shaped nuts Each side of the rack mount is composed of a main rail and either a medium or a short rear rail secured by two long screws on the front and rear of the rack. A third lon

  • D-Link DSN-5210-10 - xStack Storage Area Network Array Hard Drive, DSN-5000 series Hardware Reference Guide iii Safety Information There is a danger of a new battery exploding if it is incorrectly installed. Replace the battery pack only with the same or equivalent type recommended by the manufacturer. Do not dispose of the battery along with household waste. Contact your local waste disposal agency for the address of the nearest battery deposit site. This product also uses a lithium coin cell battery. The lithium coin cell battery is a long-life battery, and it is very possible that you will never need to replace it. However, should you need to replace it, consult your service documentation. Do not

  • DSN-5000 series Hardware Reference Guide v Preface This document is intended to assist users with installing the primary array and expansion array of the xStack Storage system from D-Link. This document assumes that users are computer literate, familiar with Storage Array Products, and have a basic understanding of storage products and concepts. Typogr

  • D-Link DSN-5210-10 - xStack Storage Area Network Array Hard Drive, 26 Chapter 4 DSN-5000 Expansion Array Layout and Installation 4.1 Expansion Array Front Panel Components The front of the DSN-5000-10 expansion array enclosure has the following components (see Figure 4-1):  LEDs - four enclosure LEDs at the right side of the front panel provide status information about the DSN-5000 series primary array enclosure. For a description of these LEDs, see Table 4-1.  Drive slots – the front panel provides access to 12 drive slots. The drive slots are arranged in four columns of 3 slots.  Drive carriers - drives are mounted on a drive carrier. Drive carriers have a push-button lever for

  • D-Link DSN-5210-10 - xStack Storage Area Network Array Hard Drive, 12 Chapter 2 DSN-5000 Series Primary Array Layout 2.2 Rear Panel Components The rear panel of the DSN-5000 series primary array controller has the following components (see Figure 2-4 and Figure 2-5):  Four or Eight 1-Gigabit RJ-45 iSCSI data ports, or one 10-Gigabit XFP iSCSI data port are located on the rear panel of the DSN-5000 series chassis controllers. Each iSCSI data port has port speed and port activity LEDs (see Table 2-4 for the xStack Storage DSN-5110-10 and DSN-5210-10, and Table 2-5 for the xStack Storage DSN-5410-10). �

  • D-Link DSN-5210-10 - xStack Storage Area Network Array Hard Drive, 42 Appendix B Installing the System in a Rack 2. Assemble the rails that will accommodate the array in the rack. The long main left and right rails are used in all installations (these rails have a bottom piece on which the array sits in the rack). However, you must determine whether to use the two medium rear rails or the two short rear rails based on the depth of your rack. Then assemble the main and rear rails together at the exact length to match the distance between the front and rear vertical supports of the rack. 3. After determining which rear r

  • D-Link DSN-5210-10 - xStack Storage Area Network Array Hard Drive, DSN-5000 series Hardware Reference Guide 37 A.4 Replacing the I/O Module on the Expansion Array Use the following procedure to replace the I/O module on the expansion array. 1. Power down the DSN-5000 series primary and DSN-5000-10 expansion array and remove the power cords from the back panel. 2. Squeeze down on the top of the levers on either side of the I/O module on the DSN- 5000-10 expansion array and pull down to disengage the module, then pull the module straight out of the enclosure. 3. Install

  • D-Link DSN-5210-10 - xStack Storage Area Network Array Hard Drive, DSN-5000 series Hardware Reference Guide 27 Figure 4-2. Close-up View of the Lever Release Button and Status LEDs on a Drive Carrier Table 4-2. Drive Carrier Status LEDs LED Color Description LED 1 Green This LED is reserved for future use. OFF = no drive is installed (drive slot is empty). ON = drive is online, ready for operation. Slow Flash = drive is being prepared for removal or is being rebuilt. Green Fast Flash = drive is being identified. LED 2 Amber Fast Flash = drive failed and should be replaced (see Appendix A for information about installing or replacing drives) LED3 Green Flash = drive acti

  • 28 Chapter 4 DSN-5000 Expansion Array Layout and Installation 4.2 Expansion Array Rear Panel Components The rear of the DSN-5000-10 expansion array enclosure has the following components (see Figure 4-4):  One or two I/O modules, each containing two SAS connectors (HOST and EXP); the HOST connector connects the expansion array to the mini-SAS connector on the back of the DSN-5000

  • 14 Chapter 2 DSN-5000 Series Primary Array Layout The DSN-5000 series primary array is “HA-capable” (High Availability) and can be equipped with dual controllers for automatic failover in the event of a hardware or software failure on the primary controller. For systems with dual controllers, both controllers must have the same number and type of data ports. To allo

  • D-Link DSN-5210-10 - xStack Storage Area Network Array Hard Drive, 20 Chapter 3 Installing the DSN-5000 Series Primary Array 3.3 Unpacking the DSN-5000 series Primary Array After receiving the DSN-5000 series primary array, perform the following steps to ensure that the primary array and other contents arrived safely. 1. Inspect the outer shipping container for any damage that may have occurred in shipping. Report any sign of damage to the appropriate shipping agency. 2. Remove the DSN-5000 series primary array and cables from the shipping container. 3. Save the shipping container, foam, and antistatic bags in case you have to return the DSN

  • D-Link DSN-5210-10 - xStack Storage Area Network Array Hard Drive, 36 Appendix A Replacing and Upgrading FRUs A.3 Replacing the Controller Module on the Primary Array Use the following procedure to replace a controller module on the primary array. 1. Power down the DSN-5000 series primary array and remove the power cords from the back panel. 2. Squeeze down on the top of the levers on either side of the controller module on the primary array and pull down to disengage the module, then pull the module straight out of the enclosure. 3. Install a repl

  • ii © 2010 D-Link Networks, Inc. All Rights Reserved D-Link Systems, Inc. makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. D-Link Systems, Inc. shall not be liable for errors contained herein or for incidental or consequential damages in connection with the

  • D-Link DSN-5210-10 - xStack Storage Area Network Array Hard Drive, DSN-5000 series Hardware Reference Guide 29 3. Save the shipping container, foam, and antistatic bags in case you have to return the DSN-5000-10 expansion array. Returning the DSN-5000-10 expansion array in any other container is not advised. 4. Check the contents against the items referenced on the packing list. If any item is missing or damaged, notify a sales representative and/or the shipping agency. 4.5 Items Supplied by the User Table 4-3 lists the additional items you must supply to perform the DSN-5000-10 expansion array installation. All users must provide the items in the first row of Table 4-3. Rack-mount users must provide the addition

  • 30 Chapter 4 DSN-5000 Expansion Array Layout and Installation 4.7 Connecting DSN-5000-10 Expansion Arrays to a DSN-5210-10 or 5410-10 Primary Array To connect the first two DSN-5000-10 expansion arrays to a DSN-5000 series primary array, use the following procedure (and refer to Figure 4-5). 1. Facing the rear of the primary array, connect one end o

  • D-Link DSN-5210-10 - xStack Storage Area Network Array Hard Drive, DSN-5000 series Hardware Reference Guide 7 A DSN-5110-10 with dual controllers (an additional controller DSN-510 is inserted in the second bay), a DSN-5210-10 with dual controllers (an additional controller DSN-520 is inserted in the second bay) or a DSN-5410-10 with dual controllers (an additional controller DSN-540 is inserted in the second bay) will require a DSN-5000-10 expansion array with two I/O modules (an additional I/O module DSN-500 is inserted in the second bay of the DSN-5000-10). An additional SAS to mini-SAS cable (provided with the DSN-500) wi

  • 2 Chapter 1 Introduction  A 115.2 Kbps RS-232-C stereo mini-jack diagnostic port for troubleshooting purposes Complete configuration and management of the storage system are available through the intuitive, graphical-based xStack Storage Management Center software. For the latest information about supported drives, consult the Interoperability Matrix found on the D-Lin

  • D-Link DSN-5210-10 - xStack Storage Area Network Array Hard Drive, DSN-5000 series Hardware Reference Guide 3 1.1 Models The xStack Storage DSN-5000 series storage array is available in various models. The models differ according to the speed and host network interface. Table 1-1 lists the xStack Storage DSN- 5000 series array models. Table 1-1. DSN-5000 series Storage Array Models Model Description DSN-5110-10 (single controller) System DSN-510 (additional controller) Number of host network connections: Four RJ-45 ports Speed: 1 Gbps Maximum number of internal SATA or SAS drives: 12 Maximum number of total SATA or SAS drives (with DSN-500

  • D-Link DSN-5210-10 - xStack Storage Area Network Array Hard Drive, 34 Appendix A Replacing and Upgrading FRUs A.1 Installing or Replacing Drives Before you install or replace drives, plan where you will be placing the disk drives. If an array will not be fully populated with drives, be sure the drive slots contain drive trays and/or blank filler panels. For more information, see Figure 2-3 and Section 2.1. High Availability (HA) Note: A system using a single controller (DSN-5110-10. DSN-5210-10 or DSN-5410-10) and its expansion array(s) may use SAS or SATA drives. A system using dual controllers for High Availability operation (DSN- 510 for the 5110-10, DSN-520 for the 5210-10 or DSN-540 for the

  • D-Link DSN-5210-10 - xStack Storage Area Network Array Hard Drive, DSN-5000 series Hardware Reference Guide 43 7. Secure the rails to the rack by inserting screws in the top and bottom holes on the left and right sides on the front of the rack (as shown in the following figure). Do not insert screws into the second-from-the-bottom hole at this time. Figure B-3. Securing the Rails to the Rack 8. Insert screws into the middle two rear rail holes. 9. Verify that the rails are installed securely in the rack. 10. Carefully slide the array onto the rails, pushing it back until the flanges on the front of the chassis meet the vertical supports. Figure B-4. Sliding the Array onto the Rails

Related Products and Documents (Carrying Case):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 AMX TXC32 Schematic diagram amx/txc32-E8G.pdf 06 Mar 2024 1 0.05 Mb
2 Blodgett SC-10DS Parts list blodgett/sc-10ds-JMR.pdf 10 Dec 2022 9 0.54 Mb
3 Squier Vintage Modified Tele Thinline Specifications squier/vintage-modified-tele-thinline-7G1.pdf 22 Jul 2022 2 0.57 Mb
4 Oneida Air Systems Dust Deputy AXD001004 Owner's manual oneida-air-systems/dust-deputy-axd001004-U12.pdf 14 Oct 2022 12
5 Sharp LD-26SH1U Operation manual sharp/ld-26sh1u-1U1.pdf 02 Jul 2022 72 0.89 Mb
6 Sony BVM-L Series Brochure & specs sony/bvm-l-series-S1S.pdf 19 Oct 2023 18 0.44 Mb

Similar Resources:

  • OttLite

    KCY008

    (2 pages)
    English 13w Craft Carry CaseINS130068 REV11261313w Craft Carry CaseKCY008 CDO-039CONGRATULATIONS!You’ve purchased the finest in natural lighting technology with your new OttLite® product.PRODUCT REGISTRATION FORMPlease complete the enclosed Product Registration Form and return it today by mail, or register online by going to: http://warranty.OttLi …
  • Hypertec

    N7858NHY

    (1 pages)
    College bag for notebooks - use over the shoulder or as a backpackWhether you prefer to carry your notebook bag over your shoulder, in your hand, or strapped to your back, the Uni.On will be the right bag for you.Backpack and bag in one - the backpack straps are concealed in a special pocket when not in use, to make this bag absolutely versatile. A shoulder …
  • LaCie

    2big USB 3.0

    (37 pages)
    LaCie 2big USB 3.0 • DESIGN BY NEIL POULTON Table of ContentsUser Manual page 1Table of Contents1. Introduction .............................................................................................................. 41.1. Minimum System Requirements ................................................................................................... …
  • Hypertec

    ExecutiveClassic N6388LHY

    (1 pages)
    A classic notebook bag made of high-quality leatherThis leather bag is the ideal companion for short business trips. Two large separate compartments provide maximum protection for a notebook and printer or projector. Additional compartments have been integrated in the interior for documents. Further mobile accessories can easily be stowed in the zip-down w …
  • Hypertec

    3704

    (1 pages)
    Series 3 3704 Our patented air-cell protection. Surrounded by interconnected pockets of compressed air, your laptop is safeguarded against vibrations and shocks. A unique world-wide tracking system. Unique i-TRAK™ codes make your luggage and laptop unique and identifiable if you lose or forget them. Series 5 and above An adjustable laptop co …
  • satmap

    ProSHIELD

    (12 pages)
    ProSHIELDUser GuideSilikon-Schutzhülle | BedienungsanleitungEtui protecteur en silicone | Guide d’utilisationCustodia protettiva in silicone | Manuale utenteFunda protectora de siliconas | Guía de usuarioBeschermende Siliconenhoes | GebruikershandleidingSilikon beskyttende veske | Brukerveiledningsatmap.comSilicon Protective Case …

Comments, Questions and Opinions: