D-Link DP-301 Hardware Manual

Text of D-Link DP-301 User Guide:

• D-Link DP-301, DP-301 Print Server Hardware Guide Unpacking and Installation 9 steady long flashes Firmware Reload Required continuous on DRAM Error One long, two short flashes Timer INT Error One long, three short flashes Flash Protected One long, four short flashes Flash ID Error One long, five short flashes Flash Erase / Program Error One long, six short flashes LAN Controller Error One long, seven short flashes LAN Memory Error One long, eight short flashes Parallel Controller Error One long, nine short flashes LPT Error steady short flashes EERPROM Error One long, eleven short flashe

• 0 A BOUT THIS G UIDE This manual describes the D-Link DP-301 Ethernet/Fast Ethernet Multiprotocol Print Server, including full descriptions of its features, detailed installation procedures, and troubleshooting information. Your DP-301 package includes important software components, and additional user manuals. The software components, and procedures for installation and setup o

• D-Link DP-301, 1 1 I NTRODUCTION The DP-301 Print Server is a compact print server which connects to your Ethernet or Fast Ethernet network anywhere you wish to locate printer services. It manages the flow of print files from your workstations or file servers to its connected printers, delivering print jobs to high-performance printers much faster than a file server or a PC acting as a print server can. DP-301 Print Server

• D-Link DP-301, DP-301 Print Server Hardware Guide 12 Product Specifications Management and Diagnostics Standard: SNMP MIBs: MIB-II (RFC 1213) Diagnostic LED Indicators: Pw/Tx, Link/Rx, LPT Environmental and Physical Power Supply: External power supply providing 12VDC/ 500mA Dimensions: 139.5mm × 114.5mm × 27.2mm Weight: approx. 165g Operating Temperature: 0 to 50°C Storage Temperature: -10 to 50°C Humidity: 10% to 90% non-condensing Emissions: FCC Class A, CISPR 22 Class A, VCCI Class 1, AS/NZS 3548:1995 Class A Safety: UL (UL 1950), CSA (CSA950), TUV/GS (EN60950)

• D-Link DP-301, T ABLE OF C ONTENTS 0 A BOUT THIS G UIDE 1 I NTRODUCTION .............................................................................1 Service Features .............................................................................2 External Features ...........................................................................3 Rear Panel ....................................................................................3 LED Indicators ...............................................................................4 2 U NPACKING AND I NSTALLATION .................................................6 Unpacking and Inspecting .........................................................

• D-Link DP-301, DP-301 Print Server Hardware Guide Introduction 3 Your D-Link DP-301 package includes PS Admin, a Windows-based setup and administration program, which makes configu-ration and management of your D-Link print servers quick and easy in a Windows environment. The DP-301 also has a Telnet interface for management communications. If Windows is not available on the station you choose for print server administration, then all configuration and management commands may be issued to the DP-301, and all console messages and management report information will

• D-Link DP-301, DP-301 Print Server Hardware Guide Unpacking and Installation 7 Installing the DP-301 Follow these steps for a trouble-free start of print-server operations with your DP-301. Please take particular notice of the warning in step 4: the network connection should be made before supplying power to the DP-301. 1. Confirm proper operation of the printer to be connected to the DP-301. 2. When you have confirmed proper operation of the printer, switch its power off. 3. Confirm that your network is operating normally. 4. Connect the DP-301 to the network (through the RJ-4

• DP-301 Print Server Hardware Guide 8 Unpacking and Installation Power-up and Self-Test Whenever the DP-301 is powered up, two kinds of testing procedures follow automatically. The first procedure is just a programmed series of LED flashes, to confirm proper operation of the three LED indicators. The second procedure comprises programmed tests of each of the DP-301's major c

• D-Link DP-301, 2 2 U NPACKING AND I NSTALLATION This chapter explains how to install your DP-301 print server and connect it to the network. It also describes the automatic power-on self test, and provides instructions for convenient Velcro mounting. Unpacking and Inspecting Carefully remove all items from the package. In addition to this Hardware Guide, be certain that you have: ♦ One DP-301 print server ♦ One DC power adapter suitable for your electric power service ♦ Two PS Admin for Windows software diskettes ♦ One PS Admi

• D-Link DP-301, DP-301 Print Server Hardware Guide 2 Introduction Service Features DP-301 print servers improve network printing services in three ways: ♦ The DP-301 picks up the workload of managing print file traffic to its connected printers. This provides workload relief to your file servers, and allows the file servers' full capacity to be used for file access or other direct services to network users. On peer-to-peer networks, workstations can print directly to the DP-301 without increasing the load of another workstation or server. ♦ The DP-301's IEEE 1284 compliant high-speed bidirectional parallel printer port can transmit to high-speed laser printers much faster than

• D-Link DP-301, B 4 P ORT P INOUTS The following table lists the pinouts of the DP-301's 25-pin parallel port connector (identical to the parallel port connector used on most personal computers), and the corresponding pin numbers for the 36-pin Centronics connector as used on most printers. Signal names beginning with n are active-low signals. 25-pin Centronics Signal Source 1 1 nStrobe Host 2 2 Data 1 Bidirectional 3 3 Data 2 Bidirectional 4 4 Data 3 Bidirectional 5 5 Data 4 Bidirectional 6 6 Data 5 Bidirectional 7 7 Data 6 Bidirectional 8 8 Data 7 Bidirectional 9 9 Data 8 Bidirectional 10 10 nAck Printer 11 11 Busy Printer 12 12 PError Printer 13 13 Select Pr

• D-Link DP-301, DP-301 Print Server Hardware Guide 10 Unpacking and Installation Velcro tape (pull the "hook" tape apart from the "loop" tape -- the hook tape has stiff little plastic hooks, which give its surface a rough feel, and the loop tape has a mat of soft plastic filaments which gives it a smooth, soft feel). The bottom housing of the DP-301 case features two corner markers which indicate the best location for applying the Velcro loop tape. Peel the white backing off of the loop tape, to expose its adhesive surface, and press it onto the bottom of the DP-301, between the corner markers. Choose a mounting surface, and

• D-Link DP-301, Link in writing, the replacement Software is provided only to the original licensee, and is subject to the terms and conditions of the license granted by D-Link for the Software. Replacement Software will be warranted for the remainder of the original Warranty Period and is subject to the same limitations and exclusions. If a material non-conformance is incapable of correction, or if D-Link determines in its sole discretion that it is not practical to replace the non-conforming Software, the price paid by the original licensee for the non-conforming Software will be refund

• repair or service in any way that is not contemplated in the documentation for the product, or if the model or serial number has been altered, tampered with, defaced or removed; Initial installation, installation and removal of the product for repair, and shipping costs; Operational adjustments covered in the operating manual for the product, and normal mai

• D-Link DP-301, A 3 P RODUCT S PECIFICATIONS Printer Connection Printer Port: IEEE 1284 standard bidirectional parallel interface with 25- pin connector. Bidirectional Communication: Hewlett-Packard PJL (Printer Job Language) standard for bidirectional communication. Network Connection Network Standards: IEEE 802.3 10Base-T Ethernet, IEEE 802.3u 100Base-TX Fast Ethernet Network Data Transfer Rate: 10Mbps and 100Mbps (megabits per second), according to network environment. Network Connector: RJ-45 connector for 10Base-T or 100Base-TX twisted pair connection; NWay automatic speed negot

• D-Link DP-301, DP-301 Print Server Hardware Guide 4 Introduction Network Port The network port (RJ-45 receptacle) provides for connection to the network through 10Base-T Ethernet cabling, or Category 5 twisted-pair cable for 100Base-TX Fast Ethernet. This port has autonegotiation (NWay) functionality, which enables the DP-301 to automatically negotiate and set its data rate to the highest rate allowed by its network. DC Power Input The DC power input socket has the label: The power supply included in your DP-301 package is correct

More Instructions:

D-Link DP-301 Frequently asked questions 18-07-2022 2

DOWNLOAD

Related Products and Documents (Switch):

Comparable Devices:

Similar Resources:

• Cisco 1900 series (48 pages) Corporate HeadquartersCisco Systems, Inc.170 West Tasman DriveSan Jose, CA 95134-1706 USAhttp://www.cisco.comTel: 408 526-4000800 553-NETS (6387)Fax: 408 526-4100Cisco MWR 1900 Mobile Wireless Edge Router Hardware Installation GuideCustomer Order Number: DOC-7813982=Text Part Number: 78-13982-02 …

• HP 7550 (2 pages) 1 unpack your hp printer 2 plug in the power cord3 load plain paper in the IN tray1. Lift the OUT tray.2. Pull out the paper length guide on the IN tray. 3. Slide the paper width guide as far to the left as itwill go.4. Move the photo tray slider toward you until it stops.This disengages the photo tray. 5. Place a stack of plain paper into the IN tray.6. …

• Dell PowerEdge M910 (45 pages) PowerEdge M910 Name Technical Guide The PowerEdge M910, an ideal server for demanding applications at the core of most data centers, such as large databases, virtualization and messaging infrastructure. …

• Cisco HWIC-4ESW - EtherSwitch HWIC Switch (118 pages) Corporate Headquarters:Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA© 2006 Cisco Systems, Inc. All rights reserved.Cisco HWIC-4ESW and HWIC-D-9ESW EtherSwitch Interface CardsFirst Published: May 17, 2005Last Updated: April 15, 2006This document provides configuration tasks for the 4-port Cisco HWIC-4ESW and the 9-port Cisco HWIC-D- …

• Renkforce 1362469 (8 pages) Bedienungsanleitung 3 Port USB3.0-Hub mit Audio-Anschlüssen Best.-Nr. 1362469Bestimmungsgemäße VerwendungDas Produkt ist zum Anschluss an einen Computer mit USB-Schnittstelle vorgesehen und stellt drei USB-Ports zur Verfügung. Der Hub entspricht der USB 3.0-Spezikation und ist abwärtskompatibel zu USB 2.0. Die Spannungsversorgung erfolgt über die …

• ZyXEL Communications XGS-4728F (2 pages) BenefitsStackable 24-port L3 Gigabit Switch with optional 10G uplinks XGS-4728FŁ24 Dual-personality Gigabit PortsŁTwo Built-in 12G Stacking InterfacesŁ1 Open Slot for Optional 2 10- Gigabit Uplink ModuleŁL3 Advanced Routing Protocols, OSPF, VRRP and DVMRPŁ16 K L2 MAC Address Table/ 8K IP Address Table/ 8K Routing PathŁ …

Comments, Questions and Opinions: