Manualios.com

D-Link DG-102SH Manual 

D-Link DG-102SH Manual Online:

4.05, 2679 votes
D-Link DG-102SH User Manual
D-Link DG-102SH User Guide
D-Link DG-102SH Online Manual

Text of D-Link DG-102SH User Guide:

  • D-Link DG-102SH, 81 REPAIR, REPLACEMENT OR REFUND OF THE DEFECTIVE OR NON-CONFORMING PRODUCT. THE MAXIMUM LIABILITY OF D-LINK UNDER THIS WARRANTY IS LIMITED TO THE PURCHASE PRICE OF THE PRODUCT COVERED BY THE WARRANTY. THE FOREGOING EXPRESS WRITTEN WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ANY OTHER WARRANTIES OR REMEDIES, EXPRESS, IMPLIED OR STATUTORY Governing Law: This Limited Warranty shall be governed by the laws of the State of California. Some states do not allow exclusion or limitation of incidental or co

  • D-Link DG-102SH, 40 Using Web-Based Management Administration Management window To add or change a User Account, fill in the appropriate information in the User Name, Old Password (if applicable), New Password, and Confirm New Password fields. Click on the Save button to keep the settings. Administration Management

  • D-Link DG-102SH, 76 Technical Specifications Call Control Protocols Compliance H.323 Voice Compression G.711 (A-law and u-law), G.723.1, G.729a Analog Voice Ports Type: Loop-Start FXS interfaces DTMF tone detection/generation V.21/V.25 Modem/Fax tone detection Echo Cancellation: G.165/G.168 Ethernet Ports WAN: NWay 10/100BASE-TX Fast Ethernet ports (MDI-II) LAN: NWay 10/100BASE-TX Fast Ethernet ports (MDI-X) IEEE 802.3 10BASE-T Ethernet compliance IEEE 802.3u 100BASE-TX Fast Ethernet compliant Quality of Service Voice service is prioritized over the data traffic. FAX Support

  • D-Link DG-102SH, 47 Using Web-Based Management Save Changes window After the settings have been saved to NV-RAM, they will become the default settings for the device, and they will be used every time it is powered on, reset or rebooted. The only exception to this is a factory reset, which will clear all settings and restore them to the initial values present when the device was purchased. Click on the Save Configuration button at the bottom of the window to save the system settings to NV-RAM. Click on the Save button at the bottom right of the window to save the settings. Use Config File: Toggle to Enabled to use the settings in a configuration text file when the device is r

  • D-Link DG-102SH, 65 Using the Boot Menu Update Boot and Application Each item on the Update Boot and Application screen is described below: Software Update Mode: This specifies downloading the image file through a WAN Link. TFTP Server Address: The IP address of the TFTP server where the runtime or configuration file is located. This entry is used only if the Firmware Update is set to Enable. Firmware Update: Determines whether or not the device will try to look for a runtime image file on the TFTP server. File Name: The complete path and filename of the runtime

  • D-Link DG-102SH, 8 Getting Started Identifying External Components Fast Ethernet LAN: A 10/100 dual-speed Ethernet port fitted with an RJ- 45 connector used to connect the VoIP gateway to a LAN device (hub, switch, PC, etc.). This port accepts Category 5 or higher UTP cabling with an RJ-45 connector. Line: RJ-11 phone jack for connecting to a standard telephone wall out- let through an approved (No. 26 AWG or larger) telecommunications line cord. Phone 1 to 2: Normal RJ-11 phone jacks used to connect analog (and digital) telephones and fax machines. Plug your telephone(s) and/or fax machine directly into any of these jacks. Installation When choosing a place to install the VoIP Gatewa

  • D-Link DG-102SH, 59 Configuration Using a Console Configuring the VoIP Gateway Using a Web Browser The items on this window are described below: Configure H.323 window Gatekeeper Information Mode: Choose the Gatekeeper mode (Default is Auto). Gatekeeper IP Address: This IP address is necessary if you chose the Manual mode defined above. Send Keepalive RRQ to Gatekeeper: Enables or disables the Keepalive function.    Keepalive Interval: This is a user-defined Keepalive Interval.  H.323 Information Terminal Type (0...255) H.323 ID Display Name Send Register/Unregister to Gatekeeper determines whether or not the device register to Gatekeeper. Click on

  • D-Link DG-102SH, 79 Subject to the terms and conditions set forth herein, D-Link Systems, Inc. (“D-Link”) provides this Limited warranty for its product only to the person or entity that originally purchased the product from: • D-Link or its authorized reseller or distributor and • Products purchased and delivered within the fifty states of the United States, the District of Columbia, U.S. Possessions or Protectorates, U.S. Military Installations, addresses with an APO or FPO. Limited Warranty: D-Link warrants that

  • 75 Command Line Interface TFTP Client Setup Commands tftp get <FILENAME> Definition: Gets the image from the TFTP server. The <FILENAME> is the name of the image on the TFTP server. If any error occurs during the image download, the message ERROR will be displayed. When the user enters tftp get, the file name in EEPROM will be employed. Example: ggdbg>tftp get c:\102nmm.tfp Download

  • 2 Contents Package Contents ................................................................................3 Introduction............................................................................................4 Features and Benefits ...........................................................................5 Getting Started ...............................................

  • D-Link DG-102SH, 12 Using Web-Based Management Management Configure Device IP Address The items on this window are described below: Restart Settings Get IP From: Select the method the VoIP gateway will use to obtain its IP settings once it is rebooted. Choices include: Manual: When Manual is selected, the VoIP gateway will obtain its IP settings from the fields located just below.  Configure Device IP Address window Restart System. NAT Configuration (NAT Configuration and Local Server Configuration) SNMP Trap Configurati

  • D-Link DG-102SH, 3 Package Contents System Requirements:   Internet Explorer Version 6.0 or Netscape Navigator Version 6.0 and Above Computers with Windows, Macintosh, or Linux-based operating systems with an installed Ethernet adapter Contents of Package: D-Link DG-102SH VoIP Station Gateway Ethernet Cable (Straight-through CAT5 with RJ-45 connectors) 12V/1A A/C Power Adapter If any of the above items are missing, please contact your reseller.   

  • D-Link DG-102SH, 66 Using the Boot Menu Save Changes Boot Menu—Saving Settings screen After the settings have been saved to NV-RAM, they will become the default settings for the device, and they will be used every time it is powered on, reset, or rebooted. The only exception to this is a factory reset, which will clear all settings and restore them to their initial values, which were present when the device was purchased. Factory Reset Before performing a Factory Reset, be absolutely certain that this is what you

  • D-Link DG-102SH, 50 8 data bits (sometimes called a “word length” of 8 bits) 1 stop bit (sometimes referred to as a 1-bit stop interval) No Flow control Arrow keys enabled     Configuration Using a Console Setting up a Console First-time configuration can be carried out through a “console,” that is, either (a) a VT100-type serial data terminal, or (b) a computer running communications software set to emulate a VT100. The console must be connected to the Diagnostics port. This is an RS-232 port with a 9-socket D-shell connector and DCE-type wiring. Make the connection as follows: 1. Obtain suitable cabling for the connection. You can use ei

  • D-Link DG-102SH, 71 Command Line Interface General Setup Commands nwdbg ip <IP ADDRESS> Definition: This command sets the fixed IP address, which is used as the system’s IP address if the software boot mode is Manual mode. If only nwdbg ip is typed, this command shows the IP configuration. Parameter(s): <IP ADDRESS> Example: nwdbg ip 10.1.1.120 nwdbg mask <SUBNET MASK> Definition: This command sets the fixed subnet mask, which is used as the system’s subnet mask if the software boot mode is Manual mode. If only nwdbg m

  • D-Link DG-102SH, 46 Using Web-Based Management Firmware and Configuration Update Firmware and Configuration Update window The items on this window are described below: Software Update Mode: This specifies downloading the image file through a WAN Link or Lan Link. TFTP Server Address: The IP address of the TFTP server where the runtime or configuration file is located. This entry is used only if the Firmware Update is set to Enable. Last TFTP Server Address: This is a read-only field that displays the IP address of the last TFTP server to be a

  • 73 nwdbg config Definition: This command shows all the configuration settings made by nwdbg commands. Parameter(s): None. Example: nwdbg config ping <DEST IP> <OPTIONS> Definition: This command lets the user ping an IP address from the device. Parameter(s): <DEST IP: The host ip address> <OPTIONS, -t : Ping the specifed host until stopped (type SPACE). -n count: N

  • D-Link DG-102SH, 6 Getting Started Identifying External Components Front Panel Understanding Indicators Before configuring your VoIP Gateway, take a few minutes to look over this section and familiarize yourself with the front panel LED indicators depicted below. Power: This LED is lit when the device is receiving power; otherwise, it is unlit. Status: This LED will flash quickly when the DG-102SH is either per- forming a self test or booting up. The LED will remain lit when the system is ready for a connection with the Gatekeeper. It will remain dark when the system is ready but can not receive an ac

  • D-Link DG-102SH, 57 Configuration Using a Console Configuring the VoIP Gateway Using a Web Browser To begin configuring the device, click on the Config IP & H.323 folder on the left-hand side of the window (shown below). Next, click on Config Device IP Address. The following window will appear: Configure Device IP Address window

  • D-Link DG-102SH, 21 Process Type: This is a user-defined which situation will activate Call Forward function. The entry is used only if the Call Forward is set to Enable. Using Web-Based Management Analog Port  Click on the Save button at the bottom right of the screen to save the settings. Data Port (Egress Calls and Dialing Rule Settings) First Data Port Telephone No. Table window This window allows you to view the Data Port Telephone No. Table settings. Click the Add icon on the window above to access the First Data Port Tele- phone No. Table window:

  • 70 Command Line Interface General Setup Commands nwdbg dtmf_relay <0|1> Definition: This command turns the Dual Tone Multiple Frequency (DTMF) relay function on or off, or shows the DTMF relay state if only nwdbg dtmf_relay is typed. Parameter(s): <0 : off, 1 : on> Example: nwdbg dtmf_relay 0 nwdbg mac <MAC ADDRESS> Definition: This command sets the MAC address of the voic

  • D-Link DG-102SH, 39 Using Web-Based Management SNMP Trap Configuration SNMP Trap Configuration window The items on this window are described below: Click on the Save button at the bottom right of the window to save the settings. Trap Manager IP Address: The IP address of the trap receiving station. Community Name: A user-defined SNMP community name. SNMP AuthTrap: This allows you to enable or disable the SNMP trap.   

  • D-Link DG-102SH, 77 Network Management SNMP management agent base MIB II Telnet provisioning Manage functions through an intuitive web-based graphical user interface Local management console TFTP: The built–in Trivial File Transfer Protocol provides firmware upgrade Security Password Authentication Protocol/Challenge Handshake Authentication Protocol (PAP/CHAP) Administrative password through Telnet, Console, Web and SNMP Technical Specifications LEDs General Power Status Ethernet WAN: 10/100M, Link/Act LAN: 10/100M, Link/Act Line Hook/Ringing

  • D-Link DG-102SH, 37 Using Web-Based Management First Local Server Configuration window This window allows you to view the current local server configuration settings. Click the Edit icon on the window above to access the second Local Server Configuration window. Local Server Configuration

  • D-Link DG-102SH, 55 The VoIP gateway comes with a default IP address of 10.1.10.4. You must make sure your computer is in the same Subnet as the VoIP gateway. You can do this by changing the IP address of the computer using the screen shown below. Configuration Using a Console Configuring the VoIP Gateway Using a Web Browser Once this is done, run any browser on the computer and point it to the default IP address of the VoIP as shown below. Initial Window, First Time Connecting to the Web-Based Management Module

  • 7 Getting Started Identifying External Components 10/100M: This indicator remains unlit when there is no connection, or the port is operating at 10Mbps through a connection to a 10BASE-T device. It is lit when the port is operating at 100Mbps through a con- nection to a dual-speed or 100BASE-TX Fast Ethernet device. Link/Act: When a good link to a powered-up, but idle device is de- tect

  • D-Link DG-102SH, 25 Using Web-Based Management Analog Mode ATPM Hunt Group Table window The items on this window are described below: Enter the desired information on the window above and then click Next. Hunt Group.: This is a user-defined hunt group number for the destination ID shown below. Destination ID.: This displays the destination ID set in the previous page.  

More Instructions:

DOWNLOAD

Related Products and Documents (VoIP):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Sangean Sangean- RCR-3 Specifications sangean/sangean-rcr-3-UYE.pdf 13 Nov 2022 1 0.03 Mb
2 Frigidaire FFC15M4AW2 Service data sheet frigidaire/ffc15m4aw2-W75.pdf 26 Sep 2023 2 0.04 Mb
3 CITROEN C4 Handbook citroen/c4-236.pdf 08 Feb 2023 188 5.3 Mb
4 Gigabyte GA-8AENXP Dual Graphic Operation & user’s manual gigabyte/ga-8aenxp-dual-graphic-5P9.pdf 13 Oct 2022 96 8.75 Mb
5 McCulloch M105-97F Operator's manual mcculloch/m105-97f-17H.pdf 24 Jan 2023 32
6 Yamaha TT-R110E(Y) Owner's manual yamaha/tt-r110e-y-V9M.pdf 11 May 2023 80 3.29 Mb

Similar Resources:

  • Cisco

    SPA301

    (371 pages)
    Cisco Small Business IP Phones Models SPA301, SPA303, SPA501G, SPA502G, SPA504G, SPA508G, SPA509G, SPA512G, SPA514G, SPA525G, SPA525G2, and WIP310ADMINISTRATION GUIDE …
  • ATCOM

    AT-620

    (6 pages)
    AT-620 Quick Start Guide ATCOM TECHNOLOGY CO., LIMITED AT-620 Quick Start Guide ISSUE 1.0 2009-7-6 …
  • Vidicode

    V-Tap Analog

    (3 pages)
    Quick Guide for the V-Tap Analog V1.0 ©2017 Vidicode 1 The V-Tap Analog is a device that can record the audio from an analog telephone line or any telephone that works with a handset. The captured data is stored onto an SD card and can …
  • Grandstream Networks

    GXP-1400

    (15 pages)
    GXP 1400/1405 USER MANUAL !!!!Thank you for purchasing Grandstream GXP1400/GXP1405 Small-Medium Business IP. Make!sure!and!acknowledge!that!you!have!read!this!manual!before!using!GXP1400.!!!Package Contents: 1. Main Case 2. Handset 3. Phone Cord 4. AC Power Adaptor 5. Ethernet Cable 6. Phone Stand 7. Quick Start Guide 8. Wall Mount Spacers x2 Discl …
  • Laser

    AO-USBPHWM

    (1 pages)
    Q: I have purchased an AO-USBPHWM wireless VoIP phone, and can't seem to get it work on Linux. Can you provide me with support for my product? I notice that your other phones do have Linux support. Specifically, I am using Ubuntu 7.10. A: The Laser AO-USBPHWM is not able to be used in Linux at this stage. The factory have not released a driver for th …
  • iPECS

    eMG80

    (689 pages)
    iPECS eMG80 & eMG800 & UCP Administration & Programming Manual Please read this manual carefully before operating System. Retain it for future reference. …

Comments, Questions and Opinions: