DSC FSD-100 Operation & User’s Manual

Text of DSC FSD-100 User Guide:

• DSC FSD-100, FSD-100 Smoke Detector Sensitivity Meter User Guide WARNING: This document contains information on limitations regarding product use and func- tion and information on the limitations as to liability of the manufacturer. Read the entire manu- ally carefully.

• DSC FSD-100, Table of Contents Introduction 1 Out of the Box ........................................................................................ 2 Battery Installation.................................................................................. 2 Controls and Indicators........................................................................... 3 Operation 4 Power Up/Power Down........................................................................... 4 Smoke Detector Testing.......................................................................... 6 Viewing Test Records .............................................................................. 7

• DSC FSD-100, 1 1 Introduction The FSD-100 Smoke Detector Sensitivity Meter is intended for comprehensive in- place-testing of the WS4916, FSA210 and FSA410 Series Smoke Detectors. The meter is hand held and battery operated, providing 20 hours of continuous operation and stores up to 500 detector tests. Features: • 9 Volt alkaline battery provides 20 hours (minimum) operation • Internal battery check displays remaining battery capacity • Battery reverse polarity protection • Automatic shutdown 4 minutes after last key press • All features are acc

• DSC FSD-100, 2 1.1 Out of the Box The FSD-100 tester includes the following: 1 FSD 100 Smoke Detector Sensitivity Meter 1 Duracell® Procell® PC1604 Alkaline 9VDC Battery 1 PC-Link Local Download KIT-DB09 1 Download kit adaptor 1 User Guide 1 Quick Reference Guide 1.2 Battery Installation: 1. Remove the rear cover 2. Remove the battery from the battery compartment 3. Remove the plastic protection from the battery terminals 4. Insert battery as indicated in the battery compartment Figure 1 - Battery Replacement NOTE

• DSC FSD-100, 3 1.3 Controls and Indicators The FSD-100 displays all information on a 32 character LCD. A PC-LINK connection is located on the right side of the unit for downloading data to a PC. The use of the , , , and keys varies depending on the screen you are cur- rently in. Use of these keys is indicated on each screen. The list below indicates the general use of these keys. Used to Scroll forward through menu selections from the Ready Mode. Moves cursor to the right in time and date programming. Used to Scroll b

• DSC FSD-100, 4 2 Operation 2.1 Power Up/Power Down Powering Up: On power up the model name and version of the tester is displayed on the top line, remaining battery capacity is displayed on the second line. NOTE: 99% indicates that the battery is fully charged. Replace battery when 1% is indicated. This screen will be displayed for 2 seconds. Record Capacity: Indicates the current number of tests stored in the tester out of a maximum of 500 tests. This screen will be displayed for 2 seconds. Time & Date Trouble: This screen will only be displayed if time and date are unprogrammed (e.g., at first power up or after battery replacement). Press # to sav

• DSC FSD-100, 5 Powering Down: The tester can be powered down in two ways: 1. The unit will automatically power down 4 minutes after the last keypress regardless of the screen it is currently in. 2. Pressing the scroll key 5 times from the Ready mode screen will dis- play the "Press for Power Down" screen. Press the key twice to power down or press to return to the Ready screen. Figure 2 - Power Up and Main Flow Menu NOTE: Pressing the key will scroll through the menu in the sequence indicated. To scroll in the reverse direction use the key. SAVE Press the , , or key for 2 seconds to power up.

• DSC FSD-100, 6 2.2 Smoke Detector Testing 1. Follow the steps indicated in Figure 3 until the TRIGGER DEVICE WAIT FOR BEEP screen appears. 2. Press the LED/Test Button located on the smoke detector with the tester. 3. Position the FSD-100 less than 2.5cm (1”) from the center dome of the smoke detector. The Smoke Detector and the FSD-100 Tester will indicate that data is being transmit- ted and received by sounding a series beeps from each device. When data transmission is completed, the beeping will stop and the FSD-100 tester will display the TEST COMPLETE ! DATA SAVED screen followed by a 2 second delay. 4. After the delay the PRESS * FOR DATA REVIEW screen will app

• 7 2.3 Viewing Test Records The Test Records section can be entered directly after a Smoke Detector Test when the PRESS FOR DATA REVIEW screen appears. This option allows you to review the preceding test only. Test records can be reviewed by following the steps indicated in Figure 4. Figure 4 - Viewing Test Records

• DSC FSD-100, 8 2.4 Downloading Test Records 1. Scroll to the "PRESS FOR DOWNLOAD" screen. 2. Connect the Tester to the Personal Computer. Figure 5 - Tester Setup 3. Open Microsoft® HyperTerminal® or equivalent. Configure the Serial COM Port as follows: • Set Baud Rate to 9600 • Set Bits to 8 • Set Parity to None • Set Stop Bits to 1 4. Press to initiate downloading. 5. When downloading is complete, a beep will be sounded and you will be prompted to delete the tester records. 6. Save File - The saved file can be exported to another program such as Microsoft® Excel®. See Program User Manual or Help File.

• 10 2.5 Checking Tester Status Tester info menu allows you to check the battery life and the number of records stored. If there is a Time/Date Trouble, the time and date can be programmed in this menu. Figure 7 - Checking Tester Status

• DSC FSD-100, 11 Appendix A: Status and Troubles The following table lists the Troubles and Status Readings found in the Trouble Status screen Troubles Status 1 Smoke Low Sensitivity 1 Tamper 2 Smoke High Sensitivity 2 For Factory Use 3 Smoke Sensor Test Failed 3 Smoke Sensor Trouble/Fault 4 Smoke Sensor Fault 4 Low Battery 5 Heat Sensor Fault 5 Smoke Early Warning 6 Measurement Errors 6 For Factory Use 7 Memory Error 7 Heat Sensor 8 Trouble Already Transmitted 8 Cold Temperature Warning Appendix B: Sensitivity Measurement Conversion The following table converts sensitivity measurements in % obscuration per foot (NA) to the approximate measurem

• DSC FSD-100, Limited Warranty Digital Security Controls Ltd. warrants that for a period of twelve months from the date of purchase, the product shall be free of defects in materials and workmanship under normal use and that in fulfillment of any breach of such warranty, Digital Secu- rity Controls Ltd. shall, at its option, repair or replace the defective equipment upon return of the equipment to its repair depot. This warranty applies only to defects in parts and workmanship and not to damage incurred in shipping or handling, or damage due to causes beyond the contr

More Instructions:

DSC FSD-100 Operation & user’s manual 21-10-2022 16

DOWNLOAD

Related Products and Documents (Smoke Alarm):

Comparable Devices:

Similar Resources:

• Kidde KN-COSM-IBA (33 pages) CombinationSmoke and Carbon MonoxideAlarmP/N 2544-7201-00 ENFor questions concerning your Smoke and Carbon MonoxideAlarm, please call our Product Support Line at 1-800-880-6788.User Guide for Model KN-COSM-IBAFor your convenience, write down the following information. If you call our Product Support Line, these are the first questions you will be asked:Alarm …

• System Sensor InnovairFlex D4240 (8 pages) SS-300-022 1 I56-3936-002RD4240 Duct Smoke DetectorINSTALLATION AND MAINTENANCE INSTRUCTIONS 3825 Ohio Avenue, St. Charles, Illinois 601741-800-SENSOR2, FAX: 630-377-6495www.systemsensor.comTABLE OF CONTENTS PAGE[1] Limitations of Duct Smoke Detectors. . . . . . . . . . . . . . . . . . . . . . . . . . 1[2] Exploded View of Duct Smoke Detector Components .. …

• Wheelock RS-2415 (6 pages) P83134 G Sheet 1 of 6 273 Branchport Ave. Long Branch, N.J. 07740 Thank you for using our products. (732) 222-6880 INSTALLATION INSTRUCTIONS SERIES RS STROBE APPLIANCES Use this product according to this instruction manual. Please keep this instruction manual for future reference. GENERAL: RS (Universal Mounting) and RSP Strobe Applianc …

• Autool SDT 202 (3 pages) TrademarkAUTOOL Technology Co, Ltd. has registered its trademarks in different countries, thetrademark is . With regard to the other trademark, service logo, domain name,icon and company name mentioned in this manual, they shall all belong to AUTOOL and itsother affiliated company, in other countries without the registration yet of these trademark,service lo …

• Firehawk FH550RF (2 pages) INTRODUCTION The FireHawk FH550RF Radio Base is designed to replace the baseplate supplied with the 250 and 450 ranges of mains powered smoke and heat alarms. When assembled to a maximum of 15 smoke or heat alarm on any one system, it allows the installer to power them all from a regularly used local lighting circuit (BS5839-6:2004 section 15.5) without th …

• Bosch DS240 (12 pages) Installation InstructionsDS240 and DS241Long Range Beam Smoke Detectors1.0 DescriptionThe DS240 and DS241 are long range projected beam type smokedetectors which consist of a separate transmitter and receiver. Internalpointability provides coverage flexibility without the need for brackets.Automatic Signal Synchronization and Range Adjustment reduceinstalla …

Comments, Questions and Opinions: