Manualios.com

Eclipse ESN E3 High-Power CD Receiver with CDC/E-COM/DSP Control and Wireless Remote Model: 54420 Owner's Manual

  • ESN E3 High-Power CD Receiver with CDC/E-COM/DSP Control and Wireless Remote Model: 54420 Car Stereo System
  • macAWRQWJnFEI
  • Owner's Manual
  • PDF / Adobe Acrobat Reader
  • 76

Eclipse ESN E3 High-Power CD Receiver with CDC/E-COM/DSP Control and Wireless Remote Model: 54420 Manual Online:

3.7, 949 votes
Eclipse ESN E3 High-Power CD Receiver with CDC/E-COM/DSP Control and Wireless Remote Model: 54420 User Manual
Eclipse ESN E3 High-Power CD Receiver with CDC/E-COM/DSP Control and Wireless Remote Model: 54420 User Guide
Eclipse ESN E3 High-Power CD Receiver with CDC/E-COM/DSP Control and Wireless Remote Model: 54420 Online Manual

Text of Eclipse ESN E3 High-Power CD Receiver with CDC/E-COM/DSP Control and Wireless Remote Model: 54420 User Guide:

  • Eclipse ESN E3 High-Power CD Receiver with CDC/E-COM/DSP Control and Wireless Remote Model: 54420, 45 How to use an optional NOB remote control ٕٕ Selecting preset stations A total of six stations may be selected (preset tuning) out of those already set in memory through the main unit. (Refer to “Manually setting stations into memory,” page 33.) 1. Press the [ DISC ] button. [] button: Tunes the next preset number at a higher frequency. [] button: Tunes the next preset number at a lower frequency. ع How to play CDs Select the disc mode first. ٕٕ Advancing to the next track or returning to the beginning of the track being played 1. Press the [ TRACK ] button. [ ] button: Skips to the next track.

  • Eclipse ESN E3 High-Power CD Receiver with CDC/E-COM/DSP Control and Wireless Remote Model: 54420, 55 How to operate the receiver with an optional DSP/EQ unit connected 2. Tap button [AUDIO CONTROL] to select the desired mode of adjustment. The mode sequence on the button is as follows: 3. Turn the [AUDIO CONTROL] button. This button adjusts the reverberation level and duration. Right: Increases the value. Left: Decreases the value. 4. Hold down a button, [1] to [6], for more than two seconds to preset a value. The preset value is overwritten by the value set using the above steps. ReverberationInitial echo delay Long Time Initial echo] Reverberation duration Direct (original sound) Level High Level • Duration value LR ○○○ dB LR ○○

  • Eclipse ESN E3 High-Power CD Receiver with CDC/E-COM/DSP Control and Wireless Remote Model: 54420, 31 How to operate the tuner ٟ How to operate the tuner First, press the [FM• AM] button to start tuner operation. There are automatic and manual methods for setting stations in memory. The receiver will accept up to 24 stations in memory: six in AM and 18 in FM (6 each for FM1, FM2 and FM3.) ع Tuning to a station 1 . Tap the [FM•AM] button to switch to the desired FM or AM mode. Each tap will switch modes from FM1 → FM2 → FM3 → AM. 2 . Press the [ ] button to tune to a station. Tap the [ ] or [ ] button for less than one

  • Eclipse ESN E3 High-Power CD Receiver with CDC/E-COM/DSP Control and Wireless Remote Model: 54420, How to operate the tuner 34 ع Preset station scan This function enables reception of all the stations in the numbered preset buttons for five seconds each. 1 . Press the [ASM] button. [P• SCAN] will appear at the top of the display, and stations stored under preset buttons [1] through [6] will beplayed for five seconds each. 2 . To stop the scan mode at a desired station, press the [ASM] button again. The receiver will stay tuned to the desired station. ع Switching the display 1 . Press the [DISP] button for less than one second. Each press of the button switches the display between the clock and current frequency. [DISP] button [ASM] button

  • Eclipse ESN E3 High-Power CD Receiver with CDC/E-COM/DSP Control and Wireless Remote Model: 54420, How to operate the CD player 26 ٟ How to operate the CD player First press the [CD] button to switch to the disc mode. It is assumed here that a CD has already been loaded into the unit. ع Listening to CDs 1 . Press the [CD] button. This turns on the disc mode and starts CD play. If an external CD changer is connected, each additional tap of the button will switch modes from CD changer 1 CD changer 2 CD player. A changer or player with no discs loaded will be skipped. ٨ Caution ٨ • Playback may be intermittent when there is a scrat

  • Eclipse ESN E3 High-Power CD Receiver with CDC/E-COM/DSP Control and Wireless Remote Model: 54420, If you have a question: 60 ٟ If you have a question: First check the items mentioned below before attempting to troubleshoot problems. ٨ Caution ٨ • If a problem occurs, for instance when the unit does not respond to any button presses, or the display doesn't work press the reset button using a sharp tool. Pressing the reset button will delete all the entries from memory. The settings will return to those made at the factory prior to shipment. A CD that has been loaded will be ejected. Open the front panel and remove the ejected CD. [Reset] button

  • Eclipse ESN E3 High-Power CD Receiver with CDC/E-COM/DSP Control and Wireless Remote Model: 54420, 41 How to use the Card remote control ع How to play CDs Select the disc mode first. ٕٕ Advancing to the next track or returning to the beginning of the track being played 1. Press the [ TRACK• APS ] button. [ ] button: Skips to the next track. [ ] button: Returns to the beginning of the track being played. • Hold the [ ] button down to fast-forward, or the [ ] button to fast-reverse the track being played. ٕٕ Skipping to the next or previous CD. 1. Press the [ DISC ] button. [ ] button: Selects the next higher n

  • How to use an optional NOB remote control 46 (previous) disc. ٕٕ Switching disc modes 1. Press the [BAND] button. When the CD changer is connected, tap the [BAND] button to change modes from CD player → CD changer 1 → CD changer 2. The indicator will skip a changer or player that has no disc loaded in it. ع Illuminating the NOB remote control The buttons of the NOB remote control will b

  • 25 Basic operation ٕ Switching Non-Fader modes 1 . Press the [FUNC] button. 2 . Press button [5] to switch the phase. 3 . Press the [FUNC] button. Pressing the button will cancel Function mode. ٕٕ Disabling the Tone Control Cancel feature 1 . Press the [FUNC] button. 2 . Press the [ASM] button to switch on or off. 3 . Press the [FUNC] button. Pressing the button will cancel Func

  • Eclipse ESN E3 High-Power CD Receiver with CDC/E-COM/DSP Control and Wireless Remote Model: 54420, 17 ESN (Key CD) security operating procedure ع What happens if an incorrect CD is inserted? 1 . An [ERR_] message will be appear, then change to a flashing [DISC], then the CD will be ejected. You will have five uninterrupted attempts to insert the correct CD. 2 . After the 5 th incorrect attempt, the display reads [CALL800] and the security indicator lights steadily. • Number of errors: Numbers indicated at _ show the number of errors that occurred. ٨ Note ٨ If after 5 tries the correct Key CD is not insereted, the display reads [CALL 800]; the unit must be returned to Eclipse to be reset. In this case, please contact your Eclipse dealer

  • Eclipse ESN E3 High-Power CD Receiver with CDC/E-COM/DSP Control and Wireless Remote Model: 54420, 33 How to operate the tuner • Press any numbered button to select the station whose frequency is indicated right above the button. • When a new station is set in memory, the station previously set in memory will be deleted. • If the number of receivable stations fewer than six, the stations set in the rest of the preset buttons will be retained. ع Manually setting stations into memory This section covers the setting of stations in memory under the numbered buttons. 1 . Press the [FM• AM] button to switch between FM and AM. 2 . Use the [ ] button to tune to the station to be

  • Eclipse ESN E3 High-Power CD Receiver with CDC/E-COM/DSP Control and Wireless Remote Model: 54420, 39 How to use the Card remote control ع Turning the power on/off 1 . Press the [PWR] button. The power turns on or off each time the button is pressed. • When the main unit is shut down, the remote control will not work. ع Adjusting the audio volume 1 . Press the [+] or [-] button. [+] button: Increases the volume. [ -] button: Decreases the volume. ٕٕ Cutting the volume instantly (muting): Press the [MUTE] button for more than two seconds to cut the volume or restore it instantly. ع Switching playback modes 1 . Press the [MODE] button. Tap the button to switch modes in the following sequence: [PWR] button [

  • Eclipse ESN E3 High-Power CD Receiver with CDC/E-COM/DSP Control and Wireless Remote Model: 54420, 65 Specifications <CD SECTION> Frequency Response 20~20,000Hz Wow & Flutter Below measurable limits Stereo Separation 64dB S/N Ratio (A-weighted) 94dB Dynamic Range 90dB Total Harmonic Distortion 0.03% (1KHz) <AUDIO AMPLIFIER> Power Output 20W×4 (20~20,000Hz,1.0% THD , 4Ω) MAX .40W×4 Output Level/Impedance 2.7V (0dB) 330Ω line-out impedance Tone Action ・Bass:±10dB at 100Hz ・Treble:±10dB at 10KHz Loudness +10dB at 100Hz /+6.5dB at 10KHz

  • Eclipse ESN E3 High-Power CD Receiver with CDC/E-COM/DSP Control and Wireless Remote Model: 54420, 21 Basic operation [DISP] button Button [6] [FUNC] button ع Adjusting audio volume 1 . Turn the [AUDIO CONTROL] button to the left or right. Turn to the left : Decreases the volume. Turn to the right : Increases the volume. • Press and hold the [E-COM] button for more than two seconds to activate or cancel MUTE function. ع Displaying the clock 1 . Press the [DISP] button repeatedly until the time is displayed. Refer to the section on “setting the clock” to set the time display. Warning Do not adjust the volume or other controls while driving the vehicle. Do so only while parked in a safe location. [AUDIO CONTROL] button [E-COM] butto

  • Eclipse ESN E3 High-Power CD Receiver with CDC/E-COM/DSP Control and Wireless Remote Model: 54420, 27 How to operate the CD player ع Advancing to the next track or returning to the beginning of the track being played 1 . Press the [ ] button. [ ] button: Advances to the next track. [ ] button: Returns to the beginning of the track being played. • Pressing and holding the [ ] button will fast-forward through a track, while pressing the [ ] button will fast- reverse. ع Playing the beginning of tracks (SCAN) 1 . Press button [4 (SCAN)]. Tapping the button causes the player to move up to the next track and play it for 10 seconds, then move up to the next track and play it fo

  • Eclipse ESN E3 High-Power CD Receiver with CDC/E-COM/DSP Control and Wireless Remote Model: 54420, 13 ESN (Key CD) security operating procedure ٟ ESN (Key CD) security operating procedure ع How to program the Key CD 1 . Turn the vehicle’s ignition on. Press the [PWR] button or [FM• AM] button to activate the tuner mode. The tuner is now turned on. 2 . Press and hold button [1], then the [FM• AM] button, and hold both for more than one second. A [SEC] message appears, then in two seconds it will change to [DISC]. The 54420 is now ready to accept your Key CD in the CD slot. 3 . Insert the CD into the slot. A [SEC] message appears, the Key CD is ejected, t

  • Eclipse ESN E3 High-Power CD Receiver with CDC/E-COM/DSP Control and Wireless Remote Model: 54420, by FUJITSU TEN R DIVISION OF FUJITSU TEN CORP. OF AMERICA 19600 SOUTH VERMONT AVENUE, TORRANCE, CA 90502 (310) 327-2151 090001-13810700 9912DE(N.O.) CUSTOMER NOTICE Please retain this booklet and write in the serial number of your 54420 for identification. The serial number is labeled or stamped on the chassis. Serial No. This device complies with part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference.

  • How to use the Card remote control 40 ع How to play the tuner Enter the tuner mode first. ٕٕ Select the FM/AM band 1. Tap the [BAND] button. Each tap will switch tuner modes from FM1 → FM2 → FM3 → AM. ٕٕ Select a station (manually or automatically) A short tap of the button will allow manual station tuning. Pressing for more than one second will s

  • Eclipse ESN E3 High-Power CD Receiver with CDC/E-COM/DSP Control and Wireless Remote Model: 54420, Mounting instruction 68 4 . Mount the stud bolt to the main unit. 5 . Insert the main unit into the mounting sleeve until it locks in place. 6 . F asten the rear of the main unit using either method [A] or [B]. Select method [A] or [B] to suit the interior configuration of the vehicle. 7 . Install the bezel on the main unit. [A] [B]  TOPTOP  TOPTOP

Related Products and Documents (Car Stereo System):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Viking BTC-1 Product manual viking/btc-1-E9J.pdf 17 Nov 2023 4 0.12 Mb
2 VOLTA UB 133 TIXY 3000 Instruction book volta/ub-133-tixy-3000-N7J.pdf 21 Nov 2023 14 0.55 Mb
3 Dell Venue 11 Pro Quick start manual dell/venue-11-pro-5XW.pdf 18 Mar 2023 2 0.08 Mb
4 Sony TA-VE810G Operating instructions manual sony/ta-ve810g-DN7.pdf 29 Aug 2022 194 2.72 Mb
5 KTM 450 Rally Factory Replica Owner's manual ktm/450-rally-factory-replica-85M.pdf 26 Jan 2024 126
6 IBM 4247-003 Brochure ibm/4247-003-IOP.pdf 06 Jan 2024 2

Similar Resources:

  • Sony

    CDXGT640UI - MP3/WMA/AAC Player CD Receiver

    (140 pages)
    Operating Instructions Bedienungsanleitung Mode d’emploi Istruzioni per l’uso Gebruiksaanwijzing ©2009 Sony Corporation4-153-060-11(1)CDX-GT640UITo cancel the demonstration (DEMO) display, see page 6.Zum Deaktivieren der Demo-Anzeige (DEMO) schlagen Sie bitte auf Seite 6 nach.Pour annuler la demonstration (DEMO), reportez-vous a la page 6.Per annullare …
  • Caliber

    MCC 100

    (30 pages)
    5. PRESET STATION [ 1-6 ] BUTTONSIn normal radio mode:A).If you press one of the preset buttons more than one second, the current station is stored inthe preset memory bank.B].To recall a preset memory, press one of the preset buttons [1-6].In PTY radio mode, the function of preset buttons is assigned according to the following list:DIGITAL BUTTON PROGRAM1 N …
  • Honda

    CASSETTE/MP3 PLAYER

    (6 pages)
    © 2005 American Honda Motor Co., Inc. - All Rights Reserved. All 30488 (0509) 1 of 6PRELIMINARY08B06-S9V-1B00-91INSTALLATIONINSTRUCTIONSAccessory Application Publications No.Issue DateSEP 20052006 PILOTCASSETTE/MP3 PLAYER(EX)Player Attachment Kit (sold separately) :P/N 08B06-S9V-100A3 Wire ties3 EPT sealerBUS cableDIN Bezel Kit (sold separately) :P/N 08B23- …
  • Bazooka

    BT6014

    (36 pages)
    PLACESTAMPHERESOUTHERN AUDIO SERVICES, INC.14763 FLORIDA BLVD.BATON ROUGE, LA 70819MODELS  MODÈLE N°  MODELO:BT6014/6018, BT8014/8018, BT1014/1018, BTA6100, BTA8100, BTA10100,BT6024DVC/6028DVC, BT8024DVC/8028DVC, BT1024DVC/1028DVC,BTA6200, BTA8200, BTA10200, MBT8014, MBT1014, MBTA8100,MBTA8200, MBTA10100, MBTA10200 …
  • Philips

    CE151/00

    (3 pages)
    Philips CarStudioCar audio system•Bluetooth•USB/SDHCCE151Experience live music in carObsessed with soundEnjoy multiple source music in your car with the Philips CE151. Stay connected to your music on your mobile & important calls, thanks to the built-in Bluetooth® receiver. Also features anti-theft detachable front panels for security.Enjoy superi …
  • Sony

    CDX-GT54UIW - Cd Receiver Mp3/wma/aac Player

    (80 pages)
    ©2009 Sony CorporationOperating Instructions Mode d’emploi Manual de instrucciones Owner’s RecordThe model and serial numbers are located on the bottom of the unit.Record the serial number in the space provided below.Refer to these numbers whenever you call upon your Sony dealer regarding this product.Model No. CDX-GT54UIW Serial No. …

Comments, Questions and Opinions: