Weider 831.153931 Operation & User’s Manual
|
Weider 831.153931, 4 BEFORE YOU BEGIN ASSEMBLED DIMENSIONS: Height: 81 in. Width: 96 in. Length: 57 in. Squat Knee Rest Curl Pad Low Pulley Station High Pulley Station Lat Bar Swivel Carriage Adjustment Knob Butterfly Arm/Press Arm Leg Lever Seat Squat Arm Weight Stack Backrest Backrest WARNING DECAL 1 WARNING DECAL 2 (one on each side) WARNING DECAL 2 Thank you for selecting the versatile WEIDER ® PRO 4850 weight system. The WEIDER ® PRO 4850 weight system offers an impressive array of weight stations designed to develop every major muscle group of the
Weider 831.153931, 13 24. Remove the preattached 3 1/2” Pulleys (78) from the Offset Double “U”-bracket (61). Wrap the Swivel Cable (17) around a 3 1/2” Pulley (78). Attach the Pulley to the Offset Double “U”- bracket (61) with a 3/8” x 1 3/4” Bolt (93) and a 3/8” Nylon Locknut (87). 25. Wrap the Swivel Cable (17) around a 3 1/2” Pulley (78). Attach the Pulley and a Cable Trap (68) to the next to bottom hole in the Small Pulley Plates (31) with a 3/8” x 2” Bolt (100) and a 3/8” Nylon Locknut (87). Make sure the Cable Trap is turned to hold the Cable in the groove of the Pulley. 26. Wrap the Swivel Cable
Weider 831.153931, 19 53. Wrap the Squat Cable (73) under a 3 1/2” Pulley (78). Attach the Pulley and a Cable Trap to the sec- ond set of holes from the top in the indicated brack- et on the Long Base (120) with a 3/8” x 2” Bolt (100) and a 3/8” Nylon Locknut (87). Make sure that the Cable Trap is turned to hold the Cable in the groove of the Pulley. 54. Wrap the Squat Cable (73) over a 4 1/2” Pulley (119). Attach the Pulley to the indicated bracket on the Top Frame (6) with a 3/8” x 1 3/4” Bolt (93) and a 3/8�
Weider 831.153931, 9 9. Attach a Roller (39) and two 5/16” Washers (90) between the indicated set of holes in the Squat Slider (38) with a 5/16” x 3 1/2” Bolt (94), two 5/16” Washers (90), and a 5/16” Nylon Locknut (86) as shown. Assemble the other three Rollers (39) to the Squat Slider (38) in the same manner. 10. Slide the Squat Slider (38) down onto the Squat Upright (4). 11. Insert the ends of two Weight Guides (42) into the indicated bracket on the Long Base (120). Slide two Weight Bumpers (49) onto the Weight Guides. Next, slide ten Weights (44) onto the Weight Guides. Make sure that the Weights are turned so the groo
Weider 831.153931, 14 29. Wrap the Lat Cable (88) around a 3 1/2” Pulley (78). Attach the Pulley and a Long Cable Trap (102) to the Top Frame (6) with a 3/8” x 1 3/4” Bolt (93) and a 3/8” Nylon Jamnut (113). Make sure the Cable Trap is turned to hold the Cable in the groove of the Pulley. 33. Wrap the Butterfly Cable (69) over a “V”-pulley (55). Attach the Pulley and a Long Cable Trap (102) to the indicated bracket on the Butterfly Upright (3) with a 3/8” x 2 1/2” Bolt (18) and a 3/8” Nylon Locknut (87). Make sure that the Long Cable Trap is turned to hold the Cable in the groove of the Pulley. 30. Remove the preattached 3 1/2” Pulleys (78) from the Pulley Plates (63)
Weider 831.153931, 2 TABLE OF CONTENTS IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Weider 831.153931, HIGH PULLEY (lbs.) 14 25 38 48 61 68 80 96 101 112 122 LOW PULLEY (lbs.) 14 25 36 44 60 70 80 91 104 111 122 LEG LEVER (lbs.) 22 35 53 67 91 111 122 148 160 184 190 BUTTERFLY ARM (lbs.) 17 26 36 45 54 63 71 80 91 100 108 PRESS ARM (lbs.) 24 39 55 70 89 104 118 136 154 167 187 SQUAT STATION (lbs.) 59 87 116 136 170 192 203 223 239 254 270 SWIVEL STATION (lbs.) 16 26 39 52 59 74 84 90 104 116 122 WEIGHT Top 1 2 3 4 5 6 7 8 9 10 24 WEIGHT RESISTANCE CHART The chart below shows the approximate weight resistance at each weight station. “Top” refers to the 10-pound top weight. The other num
23 ADJUSTING THE SQUAT ARM OR SWIVEL CARRIAGE To adjust the height of the Squat Arm (32), first turn the Adjustment Knob (115) on the Squat Bracket (37) counterclockwise several turns to loosen it. Next, pull the Handle and slide the Squat Bracket up or down to the desired position. Engage the Handle into one of the holes in the Squat Slider (not shown), and then turn the Handle clockw
Weider 831.153931, 12 20. Remove the preattached 3 1/2” Pulleys (78) from the Small Pulley Plates (31). Wrap the Swivel High Cable (74) over a 3 1/2” Pulley (78). Attach the Pulley and a Cable Trap (68) to the second set of holes from the top of the Small Pulley Plates (31) with a 3/8” x 2” Bolt (100) and a 3/8” Nylon Locknut (87). Make sure the Cable Trap is turned to hold the Cable in the groove of the Pulley. 21. Wrap the Swivel High Cable (74) over a 4 1/2” Pulley (119). Attach the Pulley inside of the indicat- ed bracket on the Top Frame (6) with 3/8” x 1 3/4” Bolt (93) and a 3/8” Nylon Locknut (87). 22. Lift the Weight Tube (43) and the Top Weight (45) closest to the Swivel Upr
Weider 831.153931, 1. Locate and open the parts bags labeled “FRAME ASSEMBLY 1” and “FRAME ASSEMBLY 2.” Press a 2” Square Inner Cap (105) into the open end of the Long Base (120). Insert eight 5/16” x 2 1/2” Carriage Bolts (110) up through the Long Base (120) and the Short Base (2) as shown. Note: It may be helpful to place tape over the heads of the Carriage Bolts to hold them in place. Attach the Short Base (2) to the Long Base (120) with two 5/16” x 2 3/4” Bolts (85), the Long Frame Plate (71), and two 5/16” Nylon Locknuts (86). FRAME ASSEMBLY 6 Make sure that you
Weider 831.153931, 18 49. Wrap the Swivel Low Cable (72) over a 3 1/2” Pulley (78). Attach the Pulley and a Cable Trap (68) between the lower set of holes in the “U”-bracket (64) with a 3/8” x 2” Bolt (100) and a 3/8” Nylon Locknut (87). Make sure that the Cable Trap is turned to hold the Cable in the groove of the Pulley. 51. Locate the Squat Cable (73), which is the only remaining cable. Attach the eyelet end of the Cable inside of the Long Base (120) with a 5/16” x 2 1/2” Bolt (59), two 5/16” Washers (90), and a 5/16” Nylon Lockn
Weider 831.153931, 3/8" x 2" Bolt (100) 3/8" x 1 3/4" Bolt (93) 3/8" x 1" Bolt (13) #10 x 1" Screw (14) 3/8" x 2 1/2" Bolt (18) 5/16" x 2 3/4" Bolt (85) 3/8" x 2 3/4" Bolt (101) 3/8" x 3" Bolt (107) 3/8" x 3 1/4" Bolt (96) 5/16" x 3/4" Button Head Screw (51) 5/16" x 2 1/2" Bolt (59) #8 x 3/4" Screw (98) 1/4" x 1 1/2" Bolt (99) 5/16" x 1" Shoulder Bolt (103) 3/8" x 3" Button Head Bolt (104) 5/16" x 2 1/2" Carriage Bolt (110) 3/8" x 2 1/2" Carriage Bolt
Weider 831.153931, 4. Press a 1 1/2” Square Inner Cap (67) into the square tube on the Butterfly Upright (3). Slide the Butterfly Upright (3) onto the two indicated 5/16” x 2 1/2” Carriage Bolts (110) in the Short Base (2). Finger tighten a 5/16” Nylon Locknut (86) onto each Carriage Bolt. Do not tighten the Nylon Locknuts yet. 5. Press a 2” x 3” Inner Cap (58) into the top of the Seat Upright (9). Attach the Leg Lever Bumper (77) to the Seat Upright with a #10 x 1” Screw (14). Slide the Seat Upright (9) onto the two indicated 5/16” x 2
5 ASSEMBLY Make sure that you have the following tools: • Two adjustable wrenches • One standard screwdriver • One phillips screwdriver • One rubber mallet • You will also need grease or petroleum jelly, a small amount of soapy water, and masking tape. Note: Assembly will be more convenient if you have a socket set, a set of open-end or closed-end wrenches, or a set of r
Weider 831.153931, 10 14. Open the parts bag labeled “ARM ASSEMBLY.” Press three 1 1/2” x 2” Inner Caps (21) into the Leg Lever (10). Attach the Eyebolt (116) to the Leg Lever with a 3/8” Washer (91) and a 3/8” Nylon Jamnut (113). Lubricate a 3/8” x 2 1/2” Bolt (18) with grease. Turn the Leg Lever (10) so that the welded tab is on the indicated side, and attach the Leg Lever to the Seat Upright (9) with the Bolt and a 3/8” Nylon Locknut (87). Do not overtighten the Nylon Locknut; the Leg Lever must be able to pivot easily. 15. Press a 2” x 2 1/2” Inner Cap (125) into the Butterfly Frame (47). Attach the tethers on the two “L”-pins w/Tether (60) to
Weider 831.153931, Note: Assembly is divided into four stages: 1) frame assembly, 2) arm assembly, 3) cable assembly, and 4) seat assembly. The hardware for each stage is packaged in separate bags. WAIT UNTIL YOU BEGIN EACH ASSEMBLY STAGE TO OPEN THE PARTS BAG LABELED FOR THAT ASSEMBLY STAGE. This chart is provided to help you identify the small parts used in assembly. The number in parenthesis below each part refers to the key number of the part from the PART LIST in the center of this manual. Important: Some parts may have been pre-assembled f
17 45. Wrap the Swivel Low Cable (72) under a 3 1/2” Pulley (78). Attach the Pulley to the indicated brack- et on the Long Base (120) with a 3/8” x 1 3/4” Bolt (93) and a 3/8” Nylon Locknut (87). 46. Route the Swivel Low Cable (72) under the indicat- ed stack of Weights (44). Wrap the Swivel Low Cable (72) under a 3 1/2” Pulley (78). Attach the Pulley to the indicated brack- et on
Weider 831.153931, USER'S MANUAL Visit our website at www.weiderfitness.com new products, prizes, fitness tips, and much more! Patent Pending CAUTION Read all precautions and instruc- tions in this manual before using this equipment. Save this manual for future reference. Model No. 831.153931 Serial No. Write the serial number in the space above for reference. Serial Number Decal (under seat) SEARS, ROEBUCK AND CO. HOFFMAN ESTATES, IL 60179
Weider 831.153931, 21 61 61. Turn the Squat Backrest (35) so that the four screw holes are closer to the bottom of the Squat Backrest than the top. Attach the Squat Backrest to the Squat Bracket (37) with four 1/4” x 3/4” Screws (114). Turn the Adjustment Knob (115) counterclockwise several times to loosen it. Next, pull the Knob and slide the Squat Bracket (37) down onto the Squat Slider (38). Engage the Knob into one of the holes in the Squat Slider, and then turn the Knob clock- wise until it is tight. 63. Make su
Weider 831.153931, IMPORTANT PRECAUTIONS 3 1. Read all instructions in this manual and in the accompanying literature before using the weight system. 2. It is the responsibility of the owner to ensure that all users of the weight system are ade- quately informed of all precautions. 3. The weight system is intended for home use only. Do not use the weight system in any commercial, rental, or institutional setting. 4. Use the weight system only on a level sur- face. Cover the floor beneath the weight sys- tem to protect the floor. 5. Make sure that all pa
Weider 220 Home Gym Operation & user’s manual
220 |
Weider Pro 4850 831.153932 Home Gym Operation & user’s manual
Pro 4850 831.153932 |
Weider PRO POWER STACK 831.159831 Home Gym Operation & user’s manual
PRO POWER STACK 831.159831 |
Weider SM10 Home Gym Owner's manual
SM10 |
Weider PRO 800 Home Gym Operation & user’s manual
PRO 800 |
Weider Pro 2250 Home Gym Operation & user’s manual
Pro 2250 |
Weider WESY86303 Home Gym Operation & user’s manual
WESY86303 |
Weider 831.159301 Home Gym Operation & user’s manual
831.159301 |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | Aiphone | GF-1DK | Features | aiphone/gf-1dk-F45.pdf | 11 May 2023 | 2 | 0.07 Mb |
2 | Sharp | XR-32X - Notevision XGA DLP Projector | Specification sheet | sharp/xr-32x-notevision-xga-dlp-projector-5U7.pdf | 06 Nov 2022 | 2 | 0.24 Mb |
3 | Honda | EG4000CL | Owner's manual | honda/eg4000cl-Y21.pdf | 11 Nov 2023 | 84 | |
4 | AOC | e2350Shk | Service manual | aoc/e2350shk-SN3.pdf | 27 Oct 2022 | 57 | |
5 | Cooper Bussmann | BU-245U-E | Operation & user’s manual | cooper-bussmann/bu-245u-e-L9L.pdf | 05 Apr 2023 | 94 | 1.69 Mb |
6 | Intellinet | 524704 | Quick install manual | intellinet/524704-62O.pdf | 08 Jan 2023 | 12 |
Weider
CAUTIONRead all precautions and instruc-tions in this manual before usingthis equipment. Save this manualfor future reference.Model No. WEEVBE24711.0Serial No.Write the serial number in thespace above for reference.Serial Number Decal(under the seat)USERʼS MANUALQUESTIONS?If you have questions, or if there aremissing parts, please contact us:UKCall: 08457 0 …
Pro 440(16 pages) |
Horizon Fitness
Horizon Fitness800 Burton Blvd DeForest, Wisconsin 53532Customer Assistance Center: 1.888.993.3199Fax: 1.608.842.1660 or www.horizonfitness.comUPRIGHT OWNER’S GUIDERev. 2.0ExpressS E R I E Sexpress 2002 console owner’s guidev2.0.qxd 3/24/2003 1:25 PM Page 1
…
Express SERIES(34 pages) |
ProForm
CAUTIONRead all precautions and instruc-tions in this manual before usingthis equipment. Keep this manu-al for future reference.Model No. 831.285371Serial No. SerialNumberDecalVisit our website atwww.proform.comnew products, prizes,fitness tips, and much more!USER’S MANUALWrite the serial number in thespace above for future reference.SEARS, ROEBUCK AND CO. …
CardioCross Trainer 831.285371(16 pages) |
ProForm
USER’S MANUALCAUTIONRead all precautions and instruc-tions in this manual before usingthis equipment. Keep this manualfor future reference.Serial Number Decal(beneath stabilizer)Model No. PFEX38440Serial No. Write the serial number in thespace above for reference.QUESTIONS?If you have questions, or ifthere are missing parts, we willguarantee complete satis …
TrainerCycle PFEX38440(24 pages) |
NordicTrack
QUESTIONS?As a manufacturer, we are com-mitted to providing completecustomer satisfaction. If you havequestions, or if parts are missingor damaged, we will guaranteecomplete satisfaction throughdirect assistance from our factory.TO AVOID UNNECESSARYDELAYS, PLEASE CALL DIRECTTO OUR TOLL-FREE CUSTOMERHOT LINE. The trained technicianson our customer hot line wi …
NTXC80181(16 pages) |
Bodyworx
Home Gym with Model No: 1Retain this owner’s manual for future reference Read and follow all instructions in this owner’s manual Version A L7800LPBODY WORXBODY WORX Leg Press
…
L7800LP(16 pages) |
Pioneer Home Theater System X-NM1Pioneer X-NM1 Guide (Operating instructions manual), @R4XUVO X-NM1, 80 |
Kingston Technology Switch KND1610TXSwitch Operation & user’s manual (Kingston Technology KND1610TX) KND1610TX, 25 |
Mamas & Papas Car Seat Mercury G 1Car Seat #NM7G8F Mercury G 1, 18 |
Tenda Adapter TWL542UTenda Product User Manual: TWL542U PDF Operation & user’s manual - 246Z41 TWL542U, 18 |
Harman Kardon Amplifier CITATION IIIXHarman Kardon Amplifier Assembly and operation manual (File: harman-kardon-citation-iiix-owner-s-manual-57, 21.01.2024) CITATION IIIX, 57 |
Motion Computing Digital Camera CL900 FWS-001User Manual: Motion Computing CL900 FWS-001 (32W6IH, Upd.21/08/2023) CL900 FWS-001, 2 |
LITTLE BEAVER Lawn and Garden Equipment Kwik-Trench KT200BKwik-Trench KT200B Operation & user’s manual - 58A595 Kwik-Trench KT200B, 20 |
Sony Transmitter TMRBT10ATransmitter Operating instructions manual (Sony TMRBT10A) TMRBT10A, 44 |
Electrolux Refrigerator 102256Refrigerator PDF Specifications 102256, 2 |
TMC Media Converter TM7006ETMC Media Converter TM7006E Operation & user’s manual TM7006E, 66 |
JD Digital Camera 4100Z3Digital Camera #OTWTQ2 4100Z3, 78 |
Kleenmaid Dishwasher DW7BManual: Kleenmaid DW7B (4149C6, Upd.Tuesday 21-11-2023) DW7B, 17 |