Manualios.com

Toshiba AD268 Operation & User’s Manual

Toshiba AD268 Manual Online:

3.4, 1385 votes
Toshiba AD268 User Manual
Toshiba AD268 User Guide
Toshiba AD268 Online Manual

Text of Toshiba AD268 User Guide:

  • Toshiba AD268, User’s Manual 7 Part 1 8 Channel Analog Input Module AD268 1. Introduction, 8 2. Specifications, 10 3. Input Type Setting, 12 4. Wiring, 14 5. I/O Allocation and Programming, 17 6. Parameters, 24 7. Troubleshooting, 32 CTi Automation - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.ctiautomation.net - Email: [email protected]

  • Toshiba AD268, 46 Analog I/O Modules (AD268 / DA264 / TC218) 5. I/O Allocation and Programming PART 2 DA264 ± ±± ±5V range: D/A conversion data Hexadecimal Integer Output voltage Resolution Upper limit H3FFF 16383 +5.1196 V ::: Full scale (positive) H3E80 16000 +5 V ::: H0001 1 +0.3125 mV 0 H0000 0 0 V HFFFF -1 -0.3125 mV ::: Full scale (negative) HC180 -16000 -5 V ::: Lower limit HC000 -16384 -5.12 V 0.3125 mV / bit A = 0.3125 × D D: Digital data A: Analog signal (mV) -5V Analog output value 0 H3FFF 16383 +5.1196V -5.12V HC000 -16384 +5V H7FFF 32767 HC180 -16000 H8000 -32768 Digita

  • Toshiba AD268, User’s Manual 17 PART 1 AD268 5. I/O Allocation and Programming 5. I/O Allocation and Programming 5.1 Allocation to the T2 registers The I/O type of the AD268 is "X 8W". When the automatic I/O allocation operation is performed with a AD268 mounted on the rack, the AD268 is allocated as "X 8W". The AD268 occupies the 8 consecutive input (XW) registers of the T2. In this manual, these assigned I/O registers are expressed as XW(n), XW(n+1), ... XW(n+7). The following figure shows an example of I/O allocation window of the T-PDS programming software. In this case, the AD268 is mounted in the slot 0 o

  • Toshiba AD268, 80 Analog I/O Modules (AD268 / DA264 / TC218) 6. Parameters PART 3 TC218 Analog input actual value: (H8028 to H802F) These data show the original A/D conversion data before processing the gain and offset calibration. Module status: (H8030 to H8037) These data show the TC218’s operation status. Bit position → FEDCBA9876543210 00000 Bit Name Description 0 to 2 Input type Shows the input type. 000 (0) = Type K thermocouple 001 (1) = Type J thermocouple 010 (2) = Type E thermocouple 101 (5) = ±100mV 3 to 6 - Reserve

  • Toshiba AD268, User’s Manual 21 PART 1 AD268 5. I/O Allocation and Programming 0 to 5V / 0 to 20mA range: Input voltage/current A/D conversion data 0 to 5 V 0 to 20 mA Hexadecimal Integer Resolution Upper limit +5.1196 V +20.479 mA H3FFF 16383 :: : : Full scale (positive) +5 V +20 mA H3E80 16000 :: : : +0.3125 mV +0.00125 mA H0001 1 0 0 V 0 mA H0000 0 0.3125 mV / bit 1.25 µA / bit 0 to 20mA range: D = 800 × A D: Digital data A: Analog signal (mA) 0 H3FFF 16383 Analog input +5.1196V 20.479mA Digital value +10.2V H3E80 16000 -10.2V Upper limit Low

  • Toshiba AD268, 54 Analog I/O Modules (AD268 / DA264 / TC218) 6. Parameters PART 2 DA264 Analog output read-back value: (H8008 to H800B) These data show the D/A conversion data after processing the offset calibration. Module status: (H800C to H800F) These data show the DA264’s operation status. Bit position → FEDCBA9876543210 00000 00 Bit Name Description 0 to 2 Output type Shows the output type. 000 (0) = 0 to 5V/0 to 20mA 001 (1) = 0 to 10V 010 (2) = 1 to 5V/4 to 20mA 100 (4) = ±5V 101 (5) = ±10V 3 to 4 - Reserved 5 to 7 Hold mode Shows the output mode, clear mode (normal) or hold mode. 101 = Hol

  • Toshiba AD268, User’s Manual 35 Part 2 4 Channel Analog Output Module DA264 1. Introduction, 36 2. Specifications, 38 3. Output Type Setting, 40 4. Wiring, 41 5. I/O Allocation and Programming, 44 6. Parameters, 51 7. Troubleshooting, 56 CTi Automation - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.ctiautomation.net - Email: [email protected]

  • Toshiba AD268, User’s Manual 81 PART 3 TC218 6. Parameters 6.2 Parameter setting procedure When you change the TC218 parameters, such as input type settings, gain/offset calibrations and averaging times, use the following procedure. Step (1) Write the value "0" into the command register of the TC218 buffer memory (address H8020) by WRITE instruction. H8020 Command register ← Write 0 Step (2) Write the parameter data into the buffer memory (addresses H8000 to H801F) by WRITE instruction. Be sure

  • User’s Manual 71 PART 3 TC218 5. I/O Allocation and Programming Thermocouple (type K) input: A/D conversion data Input temperature Hexadecimal Integer Resolution Burnout detection - H7FFF 32767 Upper limit +1370 °C H6B08 27400 :: : Full scale (positive) +1200 °C H5DC0 24000 :: : +0.05 °C H0001 1 0 0 V H0000 0 -0.05 °C HFFFF -1 :: : Full scale (negative) -200 °C HF060 -4000 :: : Lo

  • Toshiba AD268, 32 Analog I/O Modules (AD268 / DA264 / TC218) 7. Troubleshooting PART 1 AD268 7. Troubleshooting 7.1 RAS information The RUN LED is provided on the front of the AD268. When the AD268 is operating normally, this LED is lit. Also the module status information is provided in the AD268‘s buffer memory (addresses H8030 to H8037). This information is useful for troubleshooting. Module status: (H8030 to H8037) These data show the AD268’s operation status. Bit position → FEDCBA9876543210 0000 Bit Name Description 0 to 2 Input type Shows the input type. 000 (0) = 0 to 5V/0 to 20mA 001 (1) = 0 to 10V 010 (2) = 1 t

  • Toshiba AD268, User’s Manual 47 PART 2 DA264 5. I/O Allocation and Programming 0 to 10V range: D/A conversion data Hexadecimal Integer Output voltage Resolution Upper limit H7F80 32640 +10.2 V ::: Full scale (positive) H7D00 32000 +10 V ::: H0001 1 +0.3125 mV 0 H0000 0 0 V 0.3125 mV / bit A = 0.3125 × D D: Digital data A: Analog signal (mV) H8000 -32768 0 H7FFF 32767 Analog output value +10V H7D00 32000 Digital data Lower limit CTi Automation - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.ctiautomation.net - Email: info@ctiautom

  • Toshiba AD268, User’s Manual 65 PART 3 TC218 3. Input Type Setting 3.2 Parameter setting by software The input type of the TC218 is specified by writing the following parameter data into the TC218's buffer memory. To access the buffer memory, T2 user program (READ and WRITE instructions) is required. When the parameter is set to the TC218, it is saved in the TC218's built-in EEPROM. Therefore, once the input type parameter is set, there is no need to execute the input type setting operation. T2 CPU TC218 Input type parameter

  • Toshiba AD268, 4 Analog I/O Modules (AD268 / DA264 / TC218) Table of Contents Part 2 4 Channel Analog Output Module DA264 1. Introduction …………….……………………………………………………………….… 36 1.1 DA264 functions............………………..…………………….………………………… 36 1.2 External features …......…………………………………………………………………. 37 2. Specifications ….………………………………………………………………………... 38 2.1 Specifications .................…………….……………………………………………….. 38 2.2 Internal block diagra

  • User’s Manual 55 PART 2 DA264 6. Parameters 6.2 Sample program to access the parameters To write the parameters into the DA264’s buffer memory, use the WRITE instruction. No special procedure is required. To read the parameters from the DA264’s buffer memory, use the READ instruction. A sample program to write/read the parameters is shown below. This is an example to set the

  • 68 Analog I/O Modules (AD268 / DA264 / TC218) 4. Wiring PART 3 TC218 External 24Vdc power supply 4.3 Wiring precautions (1) The thermocouple signal is weak voltage. Pay attention to prevent noise interference. • Shortest cable distance • Cable shield and grounding • Separation from other cables (2) This module requires 24Vdc power. Apply the 24Vdc power before (or at the same time) app

  • Toshiba AD268, 14 Analog I/O Modules (AD268 / DA264 / TC218) 4. Wiring PART 1 AD268 4. Wiring 4.1 Terminal arrangement AD268 terminal block 11P 1N 2 32P 2N 4 53P 3N 6 74P 4N 8 95P 5N 10 11 6P 6N 12 13 7P 7N 14 15 8P 8N 16 17 P24 COM 18 19 LG FG 20 Terminal No. Signal name Function 11P 21N Channel 1 input 32P 42N Channel 2 input 53P 63N Channel 3 input 74P 84N Channel 4 input 95P 10 5N Channel 5 input 11 6P 12 6N Channel 6 input 13 7P 14 7N Channel 7 input 15 8P 16 8N Channel 8 input 17 P24 External 24Vdc power (+) 18 COM External 24Vdc power (-) 19 LG Line filter ground 20 FG F

  • Toshiba AD268, User’s Manual 51 PART 2 DA264 6. Parameters 6. Parameters The DA264 has the memory that stores the control parameters, output type designation, module status information, etc. This memory is called the buffer memory. To access (read/write) this memory from the T2 program, READ and WRITE instructions are used. These parameter data are not maintained in the DA264. Therefore, you should write the necessary parameter data at each time of the beginning of the operation. 6.1 Memory map The contents of the DA264's buffer memory are as follows. Address Contents F0 H8000 Offset

  • Toshiba AD268, Important Information Misuse of this equipment can result in property damage or human injury. Because controlled system applications vary widely, you should satisfy yourself as to the acceptability of this equipment for your intended purpose. In no event will Toshiba Corporation be responsible or liable for either indirect or consequential damage or injury that may result from the use of this equipment. No patent liability is assumed by Toshiba Corporation with respect to use of information, illustrations, circuits, equipment or examples of application in this publication. Toshiba Corporation reserves the right to make changes and improvements t

  • 10 Analog I/O Modules (AD268 / DA264 / TC218) 2. Specifications PART 1 AD268 2. Specifications This section describes the AD268 specifications. The general specification for the AD268 conforms to the specification for the T2 PLC. 2.1 Specifications Item AD268 Input type Voltage input Current input -5 to 5V Bipolar -10 to 10V 0 to 5V 0 to 20mA 0 to 10V Input range Unipolar

  • Toshiba AD268, 72 Analog I/O Modules (AD268 / DA264 / TC218) 5. I/O Allocation and Programming PART 3 TC218 Thermocouple (type J) input: A/D conversion data Input temperature Hexadecimal Integer Resolution Burnout detection - H7FFF 32767 Upper limit +1200 °C H5DC0 24000 :: : Full scale (positive) +800 °C H3E80 16000 :: : +0.05 °C H0001 1 0 0 V H0000 0 -0.05 °C HFFFF -1 :: : Full scale (negative) -200 °C HF060 -4000 :: : Lower limit -210 °C HEF98 -4200 0.05 °C / bit D = 20 × A D: Digital data A: Temperature (°C) 0 Temperature HF060 -4000 Digital vale -200°C Upper limit +80

  • Toshiba AD268, User’s Manual 43 PART 2 DA264 4. Wiring 4.3 Wiring precautions (1) Use shielded twisted-pair cables for analog output signal lines and wire them in shortest distance. Connect the cable shield to ground in shortest distance for EMC conformity. Normally the grounding method (a) is recommended. However, depending on the condition, method (b) or (c) may be useful for stable operation. (2) Separate the analog signal cable from other cables to prevent noise interference. (200mm or more) (3) This module requires 24Vdc power. Apply the 24Vdc power before (or at the same ti

  • 22 Analog I/O Modules (AD268 / DA264 / TC218) 5. I/O Allocation and Programming PART 1 AD268 1 to 5V / 4 to 20mA range: Input voltage/current A/D conversion data 1 to 5 V 4 to 20 mA Hexadecimal Integer Resolution Upper limit +5.1196 V +20.479 mA H337F 13183 :: : : Full scale (positive) +5 V +20 mA H3200 12800 :: : : +1.0003125 V +4.00125 mA H0001 1 Lower limit 1 V 4 mA H0000

  • Toshiba AD268, 8 Analog I/O Modules (AD268 / DA264 / TC218) 1. Introduction PART 1 AD268 1. Introduction The AD268 is an 8 channel analog input module for the T2 series programmable controllers. The AD268 converts external analog signals (voltage or current) into digital values cyclically so that the T2 can process the analog signals. 1.1 AD268 Functions The AD268 has the following functions. 1) 8 channels input per module 2) Selectable input type • ±5V • ±10V • 0 to 5V • 0 to 10V • 1 to 5V • 0 to 20mA • 4 to 20mA 3) 16-bit high-resolution A/D conversion 4) High-speed (1ms/channel) conversion cycle 5) Gain and offset calibration fun

Related Products and Documents (Coffee Maker):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Candy CDV 262 User instructions candy/cdv-262-55M.pdf 09 Mar 2024 22 0.32 Mb
2 Sprint CDM-105 Phone manual utstarcom/cdm-105-W6W.pdf 02 Jun 2023 93 1.5 Mb
3 Thule 014 Manual  thule/014-51N.pdf 02 Apr 2023 1 0.24 Mb
4 Epson EB-1751 Specifications epson/eb-1751-75Q.pdf 24 Dec 2022 2 0.42 Mb
5 Alcatel-Lucent OMNISTACK 8008 Operation & user’s manual alcatel-lucent/omnistack-8008-3YZ.pdf 24 Oct 2023 130 1.29 Mb
6 Creative Blaster Modem Getting started manual creative/blaster-modem-ZN7.pdf 20 Dec 2023 61 0.97 Mb

Similar Resources:

  • WMF

    2000 S

    (2 pages)
    33 2510 0010 1.0 03.2010Cleaning instructions 2000 SPlease refer to User Manual.Follow the overview of cleaning interval schedule in Care chapter in the User Manual.Prior to the first cleaning, read the User Manual, Care chapter.Cleaning Program Standard1 2 3 4 5We 31.03.2010 08:16main menumixer rinsingcleaning prog.customer carefoamer cleaningswitchingOffn …
  • Arzum

    BREW'N TAKE AR3058

    (32 pages)
    BREW’N TAKEAR3058 KİŞİSEL FİLTRE KAHVE MAKİNESİAR3058 PERSONAL FILTER COFFEE MACHINEAR3058 PERSÖNLICHE FILTER-KAFFEEMASCHINEKULLANMA KILAVUZUINSTRUCTION MANUALGEBRAUCHSANWEISUNG750 WYIKANABİLİR FİLTRE• YIKANABİLİR FİLTRE •TERMOS BARDAK• PASLANMAZ ÇELİK •410 MLKAPASİTELİ …
  • Fetco

    CBS-2111XTS

    (22 pages)
    P171 FETCO CBS-2111 Coffee Brewer www.fetco.com User’s Guide and Operator Instructions FETCO Coffee Brewer: CBS-2111XTS Extractor Touch Screen Models для России: Модернизированная электронная автоматическая самовара Table of Contents Description & Features ... …
  • Gaggia

    740602008

    (61 pages)
    ISTRUZIONI PER L’USOOPERATING INSTRUCTIONSGEBRAUCHSANWEISUNGMODE D’EMPLOIINSTRUCCIONES DE USOGEBRUIKSAANWIJZINGINSTRUCÇOES E MODO DEEMPREGOSYNCRONYSYNCRONYSYNCRONYSYNCRONYSYNCRONYCOMPCOMPCOMPCOMPCOMPAAAAACTCTCTCTCTGaggia-Syncrony-cod 165892000 rev.01.PMD 14/06/2002, 17.251 …
  • Judge

    JEA29

    (8 pages)
    Page 1Instruction ManualModel No. JEA29PLEASE READ THIS INSTRUCTION MANUAL CAREFULLY BEFORE USE AND RETAIN FOR LATER REFERENCE.UNPACK YOUR ESPRESSO MACHINE CAREFULLY, REMOVE PACKING PIECES AND RECYCLE WHERE POSSIBLE. …
  • Philips

    HD7826/18

    (2 pages)
    4222.200.0545.2Descaling Ontkalken Détartrage EntkalkenDescale the SENSEO® coffee machine as described below when the CALC light goes on (after you have brewed approx. 400 cups of SENSEO® coffee).Ontkalk de SENSEO® kofemachine zoals hieronder beschreven wanneer het CALC-lampje gaat branden (nadat u circa 400 koppen SENSEO® kofe hebt gezet).Détart …

Comments, Questions and Opinions: