Eneo ENC-1001L Installation And Operating Manual

Text of Eneo ENC-1001L User Guide:

• Eneo ENC-1001L, 2 3 SAFETY PRECAUTIONS • The instructions below must be followed for your own safety. • Please read the safety instructions and operating instructions before connecting the device and putting it into operation. • Keep the operating instructions safe for use at a later date. • Never operate the camera outside of the specications as this may prevent the camera functioning. • Never point the camera towards the sun with the lens open as this may prevent the sensor functioning. • When laying the connection cable, it is essential to follow the instructions below: the cable must be laid in such a way that it is not strained, bent or damaged and

• Eneo ENC-1001L, 58 59 System requirement Windows Browser IE 5.x 6.x Camera setup Username / IP / PROXY / Password / Time / Date / Motion / Alarm Multi-camera link > 4 Cameras Viewer 1 / 4 SPLIT PT control Support Save le format BMP / JPEG / AVI 7. Function of Client PC EDP No. Description 91422 16-Chanel Viewer Software for ENC-1000P 71852 CF Memory Card 128MB for ENC-1001/1002 71853 CF Memory Card 256MB for ENC-1001/1002 47147 F1.2/2.8mm DC Lens with No Focus Shift, 1/3” CS Mount 47148 F1.2/4mm DC Lens with No Focus Shift, 1/3” CS Mount 47149 F1.2/6mm DC Lens with No Focus Shift, 1/3” CS Mount 47154 F1.2/8mm DC Lens with No Focus Shift, 1/3” CS Mount 43238 F1.0/3

• Eneo ENC-1001L, 40 41 • Change the Application Setting - ALARM - MOTION DETECTION Please follow the steps below to enable changes in the motion detection function of the alarm through the network if and as necessary. Set the motion detection: 1. Click the Motion detection button on the left side of the Alarm to enter the „ALARM - MOTION DETECTION” page. 2. Click and drag the mouse across a targeted zone to draw a red rectangle on the image (coordinates provided below). 3. Click the Save button to save the motion detection range. 4. Enables / disables the motion detection function. 5. Set up the signal level. 6. Click the Submit button to submit the new setting of the recording. 7. Click

• Eneo ENC-1001L, 34 35 • Change the System Setting - Audio mechanism Please follow the steps below to change the Audio Mechanism through the network if necessary. 1. Click the Audio mechanism button on the left side of the „System - Date and Time” page to enter the „SYSTEM -AUDIO MECHANISM SETTING” page. 2. Mark „Audio Mechanism” „ON” or „OFF” and type in your desired audio volume level from a range of 0 to 11. 3. Click the Submit button to submit the new user’s setting. 4. Click the Home b

• 16 17 4.3 TCP/IP Communication Software Follow the instructions below to install the TCP/IP communication program into your computer. Click the Start menu from your computer, and point to the Settings/Control panel. Click the Network icon twice to enter the same setting windows.

• Eneo ENC-1001L, 44 45 7. Click „Account” –> Type in your „Account password” again –> Click „Dynamic DNS (Add host)” –> Enter the „New dynamic DNS host page” –> Type in the „host name”, for example „abc123” –> Choose a host name from the drop - down list to the right of the „host name” entry (for example, „Homeip.net”) –> Click „Add host” –> The procedure is successfully completed –> You now have an „abc123 homeip.net” domain address –> Close the Website page. DDNS setti

• Eneo ENC-1001L, 66 67 7. If you wish to change any of the above setting, type the new information directly into the window. The „Mode setting” has two options: „Infra-structure” and „Ad-hoc”. You should enter „Ad-hoc”, and click „Apply”. 8. Click the „Apply” button to transfer the new settings to the LANCAM. 9. Now the settings are complete. NOTE: If your PC does not a wireless card, please insert a wireless card in your PC and use the card to search and join for the wireless connection. 10. Once the settings are complete, wh

• 34 35 • View the Event Logs. Please follow the steps below to view events through the network if and as necessary. 1. Click the button on the upper left above to enter the „EVENT LOG” page. 2. Choose one of the three buttons shown on the page to view an event when necessary. The three buttons are titled „First Page”, „Previous 20”, and „Next 20”. Description of functio

• 62 63 4. Click „Exit” at bottom right to shut the device. 2. Select and double click any of the addresses in the „Free IP Address” box on the right to enter it into an IP Address on the left. 3. To change any IP address, type in the new address in the „Free IP Address” box on the right as well as the device „Login Name” and „Password” in th

• Eneo ENC-1001L, 12 13 4. Network Conguration 4.1 Cable Connections Please follow the instructions below to connect your LAN CAMERA to a computer or a network and to choose a proper RJ-45 cable conguration for connections. Physical specication of RJ-45 cable for Ethernet 4.1.1 Connect to a computer Use a crossover LAN cable to connect directly to a computer. CROSSOVER CABLE PIN CONFIGURATION CROSSOVER CABLE TO PC LAN CARD Wire Type Cat. 5 Connector Type RJ-45 Max. Cable Length 100m Switch/Hub Wiring Conguration Straight Through PC Wiring Conguration Cross Over

• Eneo ENC-1001L, 24 25 5.1.3 Change the Network Setting Please follow the steps below to change the network setting through the network if and as necessary. • Set the network options and IP address 1. Click the network button in the home page to enter the network-setting page. 2. The accessible networks here are the FTP, the SMTP, the SNTP, the DDNS and the PPPoE0. 3. Fill in the „IP Address”, „Netmask”, „Default gateway”, „Primary nameserver”, and „HTTP Port Number” if and as necessary. 4. Click the Submit button to submit the new network setting

• Eneo ENC-1001L, 14 15 4.2 Congure Your LAN CAMERA Network Settings Upon network hardware connection, you need to activate the network function and congure the proper network settings of the LAN CAMERA. 4.2.1 Enable DHCP Function This function can only work if the LAN which the unit is connected to has a DHCP server. If the DHCP server is working, the LAN CAMERA will obtain an IP address automatically from the DHCP server. In that case please skip the section 4.2.2 (Set IP address) and follow section 4.3 (TCP/IP Communication Software). 4.2.2 Set IP Address You need to set an IP addres

• Eneo ENC-1001L, 32 33 • Change the System Setting - Digital I/O Please follow the steps below to change the Digital I/O through the network if necessary. 1. Click the Digital I/O button on the left side of the „System - Date and Time” page to enter the „SYSTEM - DIGITAL I/O SETTING” page. 2. Mark „Digital Input” „ON” or „OFF” and the „Digital Output” „ON” or „OFF”. Click your choices to enable. 3. Click the Submit button to submit the new user’s setting. 4. Click the Home button to return to the home page. Description of function keys: Digital Input: Select „ON” or „OFF” to use the GP

• 46 47 NOTE: Upon connection, the connection status box indicates the name and IP address of the selected device. If there’s a failure to connect, a „Fail” message appears on the screen right after the device IP address; otherwise an „OK” appears. To add more connections or units to the LAN CAMERA, please repeat the above instructions. F

• Eneo ENC-1001L, 52 53 Set the regular record mode 6. When in the multi-device mode, and click to enter the Record Setup page. 7. Click the Record Mode to enter the Record Mode page. (See the sample screen as in B above) 8. Set the Disk Full to Over Write to enable the Disk Full Over Write setting area. 9. Charge the image le path if and as necessary. 5. Click the OK tag to proceed. Set the System settings 3. When in the multi-device mode, and click to enter the Record Setup page. 4. Click the System Setup to enter the System Setup page. (See the sample scre

• Eneo ENC-1001L, 44 45 5.2 The LAN CAMERA Viewer NOTE: Always use the 4 channel viewer with its newest rmware. If necessary please load the current version from our web page down. NOTE: Standard is the 4 channel viewer, optional available is the 16-channel viewer. This section provides instructions for installing and using the Network Viewer, and Image Viewer, which are included with the LAN CAMERA. The programs can be operated by a selected PC equipped with the following requirements. 5.2.1 Introduction to Network Viewer The Network Viewer allows you to potentially access 16 units of the LAN CAMERA from a remote desktop

• Eneo ENC-1001L, 46 47 5.2.3.1 Login the LAN CAMERA software Once Network View is executed a Login prompt will appear, you must enter the default User Name: admin, password: 9999 into the respective eld. Click the „OK” button and enter the home page of the Network Viewer: both the user name and password must be lled correctly. Click the „Cancel” button and exit the login of the Network Viewer. 5.2.3.2 View the LAN CAMERA video from a remote PC Follow the instructions below to use the Network Viewer to browse a LAN CAMERA video from a remote location. Upon entering the Network Viewer; t

• Eneo ENC-1001L, 26 27 • Change the Network Setting - SMTP Please follow the steps below to change the SMTP setting through the network if and as necessary. 1. Click the SMTP button at upper left above to enter the „SMTP SERVER SETTING” page (OPEN RELAIS SERVER). 2. Fill in the IP address of the SMTP server, and set the recipient’s e-mail address when and as necessary. 3. Click the Submit button to submit the new SMTP setting. 4. Click the Home button to return to the home page. Description of function keys: SMTP Server: Enter the SMTP server DOMAIN NAME or IP address in the given blank space. Email Address: The recipient’s e-mail address Submit: Click to submit the new

• Eneo ENC-1001L, 42 43 5.1.7 PPPoE & DDNS Using the PPPoE 1. Install the XDSL software (obtained from your ISP dealer) in your PC. 2. Search your LAN CAMERA’s IP address: you can use your Network Viewer’s Scan IP program, or just connect the LAN CAM and the Video monitor. The monitor screen will show the IP address on its right side. 3. Change the switch on the LAN CAM’s side panel to position 4. 4. Installing an IP address in your PC or notebook. Desktop –> Move the mouse focus to the Network neighborhood and click the right key of the mouse –> Choose the properties –> Choose your local connection –> Choose the properties and select the

• Eneo ENC-1001L, 24 25 5.1.2 Change Image Setting Please follow the steps below to change the image setting through the network if and as necessary. 1. Click the image button on the home page to enter the image-setting page. 2. Adjust the image setting including „Camera Title”, „Resolution”, „Quality”, „Fluorescent”, „BLC”, „Brightness”, „Hue”, „Saturation”, „Sharpness”, and „Viewer Type” if and as necessary. 3. Click the Submit button to submit the new image setting. 4. Click the Home button to return to the home page while the new image setting acts on the images to effect the desired changes

Related Products and Documents (Digital Camera):

Comparable Devices:

Similar Resources:

• Sony DSC-W630 (451 pages) DSC-W630/W6504-410-736-53(1)DSC-W630/W650Digital Still Camera / Instruction Manual GBAppareil photo numérique / Mode d’emploi FRFotocamera digitale / Istruzioni per l’uso ITCámara fotografía digital / Manual de instrucciones ESCâmara fotográfica digital / Manual de instruções PTDigitale Fotokamera / Gebrauchsanleitung DEDigitale camera / Ge …

• TRENDnet TV-IP201W (3 pages) TV-IP201W Internet Camera Server is the perfect device for remote monitoring and transmitting real-time events over the Internet. The TV-IP201W functions as a video/audio/surveillance camera allowing you to view live events with your web browser via Internet or Intranet. Up to 16 cameras can be remotely managed with the bundled IPView software …

• Canon EOS 1500D (2 pages) Troubleshooting Steps A.Images seem to be out of focus. Solution: 1.Press the shutter button halfway to focus and then press fully down to click, also make sure the AF switch position is at AF on the lens. 2.Make sure you are the distance to achieve the focus, very close to subject while in zoom in position may lead to hunting of focus. B.Images not v …

• Vivotek IP8172 (2 pages) FixedNetwork CameraIP8172/72P5MP • Full HD • Focus AssistVIVOTEK IP8172/72P are professional box cameras offering 5-Megapixel or 1080p Full HD resolution with superb image quality up to 30 fps. Featuring 5-Megapixel resolution and high-performance H.264/MPEG-4/MJPEG compression technology, the IP8172/72P offer extra-smooth video and wide coverage.The IP8 …

• Kongsberg OE14-522A-0019 (24 pages) OE14-522A-0019 HD Pan & Tilt Zoom Camera 4500 Metre Serial Number: Campus 1 Aberdeen Innovation Park ABERDEEN, AB22 8GT Scotland Tel: +44 1224 226500 Fax: +44 1224 226501 Kongsberg Underwater Technology Inc. 19210 33rd Avenue West Lynnwood, WA 98036-4707 United States of America Tel: +1 425 712 1107 Fax: +1 425 712 1197 …

• Sanyo VPC-CG10BK (58 pages) FILE NO.REFERENCE No.SM5310775SG315/U, U3, U4, U5, UB, EX, EX2, EX4, EX3, EX5, GX2, GX3, GX5, GX, GX4NOTE: 1. Parts order must contain model number, part number, and description.2. Substitute parts may be supplied as the service parts.3. N.S.P. : Not available as service parts.Design and specifications are subject to change without notice.SERVICE MANUALCONTE …

Comments, Questions and Opinions: