Manualios.com

Epson C82324* Operation & User’s Manual

Epson C82324* Manual Online:

4.15, 609 votes
Epson C82324* User Manual
Epson C82324* User Guide
Epson C82324* Online Manual

Text of Epson C82324* User Guide:

  • Index A Answers to common questions, 3-8 C Cable connection types, 1-3 Change printer port configuration, 2-3 Change queues serviced by printer, 2-2 Configuration report, switching off or on, 2-3, 2-13 Configure port, 2-3 D Display port settings, 2-3 E EPCONFIG, 1-7 configuration report off/on, 2-12 Ethernet network type, 2-13 N=E, 2-10 queue polling interval, 2-13 rename print s

  • Epson C82324*, 3. In the “Options” menu, press ESC. Select “Reset.” Caution: Once you select “Reset," you must wait for the “Reset has been completed” message to appear before turning off the printer. Set Queue Polling Time Interval Use this command to change the interval at which the parallel port(s) check queues for waiting print jobs. To reduce network traffic, you can increase the polling interval from the default (5 seconds) to up to 30 seconds. 1. Select “Set Queue Polling Time Interval” from “Print Server Configuration Options.�

  • 2. For all workstations running the utility program for this product: You need to create (or modify) the NET.CFG file for your workstation. Create (or modify) the file, which includes the following strings, using the DOS COPY command or editor. Make sure that the main section headings are left-justified. Indent additional lines under each heading with either

  • Epson C82324*, 4. 5. 6. 7. 8. 9. 10. Select “Install New Ethernet Interface Card.” Enter the eight-digit Ethernet Card serial number. The serial number is located on the component-side of the interface board. You should already have written it down on page 1-2 and in the space provided at the front of this manual when you installed the Ethernet Card board in the printer. Select “Remote Printer Mode” for the operating mode. (For instructions on installing as a print server, see “Installing as a Print Server” earlier in this chapter.) In the Novell print server list, select the print server configured earlier. Select LPT1. Enter the number of the print server port (0-15) to which you

  • Epson C82324*, Rename Print Server Always use EPSETUP (or EPCONFIG) to rename on the master file server. Never use PCONSOLE to rename the print server on the master file server. Because EPSETUP renames the print server for all file servers on which it services queues, it is recommended over EPCONFIG. 1. Select “Rename Print Server” from “Print Server Configuration Options.” 2. Enter a print server name, up to 47 characters. The following characters are not allowed: Ctrl / \ : ; , * ?  + = [ ] ” c> and space. A period (.) is allowed

  • Epson C82324*, 3. In the “Printer Configuration” screen, you can complete the following tasks: a. Change printer port name. b. Turn configuration report printing on/off. (Pressing any alphanumeric key toggles values.) 4. When finished, press ESC and then ENTER to save changes. 5. In the “Print Server Configuration Options” menu, press ESC, or select “Reset Print Server.” Choose “Reset.” 6. If you press ESC, a box that reads “What To Do Next” appears; select “Reset.” e Caution: Once you select “Reset,” you must wa

  • Epson C82324*, 3. From the network or local drive where you copied the Ethernet Card utilities, enter EPSETUP. 4. Select “Install New Ethernet Interface Card.” 5. Enter the eight-digit Ethernet Card serial number. The serial number is located on the component-side of the interface board. You should already have written it down on page 1-2 and in the space provided at the front of this manual when you installed the Ethernet Card in the printer. 6. Select “Print Server Mode” to enter the operating mode. (For instructions on installing as a remote printer, see “Installing the Ethernet Card as a remote printer,” later in this chapter.) 7. It is recommended you rename the

  • Cannot Print to Queue, or Incorrect Results I just added a queue to my Ethernet Card using PCONSOLE, but I can’t print to it. What’s the matter? When you change the Ethernet Card configuration, you must reset (reboot) the Ethernet Card (unless you’ve made a temporary change using PCONSOLE’s Print Server Status/Control). If adding queues with EPSETUP, the program saves your configurati

  • Epson C82324*, Installing the Print Server on a Second File Server How do I install my Ethernet Card print server on a second file server with EPSETUP? EPSETUP is required for initial installation, and is the easiest method for configuring an Ethernet Card on a second file server. In EPSETUP, select “Queues Serviced by Printer.” A list of file servers displays. Select the file server where you would like to install the Ethernet Card, then assign at least one queue. Save your changes, and select “Reset Print Server.” I installed my Ethernet Card print server with EPSETUP, but now I’d like to configure it on a second file server using PCONSOLE. Wh

  • Reset (Reboot) the Ethernet Card EPCONFIG serial-number N=E RESET This command resets the specified the Ethernet Card. When in print server mode, the Ethernet Card must be reset (rebooted) after: 0 Adding or deleting a queue from a port’s service list 0 Changing a port’s name or configuration (this includes turning the configuration report on/off) 0 Setting queue

  • Epson C82324*, Enter one of the following hexadecimal values for C= ethernet_type: To configure the Ethernet Card for 802.3 only use 0001 through 05FF. To configure the Ethernet Card for the Ethernet II type 8137, use 8137 To configure the Ethernet Card for both 802.3 and the Ethernet II type 8137, use 0000. If your network uses an Ethernet II type other than 8137 enter the appropriate type for C=ethernet_type. Example: EPCONFIG 06400078 N=e C=0600 (sets Ethernet II type 600.) Restore factory Defaults EPCONFIG serial-number N=E V

  • Epson C82324*, Here is a brief explanation of indicator light activity 1 Green 1 Red 1 Function I .I, 0 .I, 0 0 0 0 Starting power-on tests Testing Looking for master file server Contacted master file server Ethernet Card ready for use I 0 I 0 I Error has occured. A diagnostic report Is printed. I Error occured during power-on test. A diagnostic report is printed. Contact your Epson dealer. I . I 0 I An error has occurred; contact your Epson dealer. On 0 Off l Flashing 0 3-2 Troubleshooting

  • Epson C82324*, Appendix Specifications Environmental Operating temp.: 5° to 35°C (41° to 95°F) Storage temp.: 0° to 70°C (32° to 158°F) Operating humidity: 20% to 80% Network Software Novell NetWare 2.15x or later, and 3.x Ethernet Network Hardware IEEE 802.3 l0BASE2 RG-58A/U coaxial cable via BNC connector or IEEE 802.3 10BASE-T straight-through twisted pair modular cable via RJ45 connector Regulatory Approvals Safety: EMI: FCC Class A UL/ CSA approved Specifications A-l

  • Epson C82324*, Before Running EPSETUP Before using EPSETUP to install Ethernet Card as a remote printer, you must do the following: 1. 2. 3. 4. 5. 6. Decide which Novell print server the Ethernet Card will operate under. (The Ethernet Card must be installed under a Novell print server running PSERVER.) Enter PCONSOLE. Select “Print Server Information,” and choose the print server you are installing the Ethernet Card under. Select “Print Server Configuration,” then “Printer Configuration.” Press ENTER t

  • Epson C82324*, Using the Ethernet Card in print server mode provides the highest printing speed while retaining the control, security and convenience of a Novell NetWare print server. Each Ethernet Card, when running in print server mode, requires a connection to a file server. You can print to the Ethernet Card just as you would to any other Novell print server, using NetWare print commands. The Ethernet Card operates like any Novell print server; servicing the assigned queues in a round robin fashion. In queues of the same priority, the Ethernet Card se

  • Epson C82324*, About This Manual This manual describes how to install, configure, and use your Ethernet Card in a Novell NetWare environment for the following cable connections: 0 Ethernet Twisted-Pair (l0BASE-T) 0 Ethernet Thin Coaxial Installation Overview Installing the Ethernet Card is simple, and is described in Chapters 1. The following steps are an overview of the installation process. 1. 2. 3. 4. Decide whether you want to set up the Ethernet Card as a print server or as a remote printer. (See How the Ethernet Card Works, later in this chapter.) Install the Ethernet Card in your Epson printer and connect it to the netw

  • Chapter 1 Installing the Ethernet Card This chapter explains how to install the Ethernet Interface Card for NetWare in your printer. This chapter also shows how to use the EPSETUP utility to install the interface on your network Hardware Installation This section describes Ethernet Card hardware installation. It explains the following tasks: Q Installing Ethernet Card in the printer 0

  • Epson C82324*, cl cl 0 0 cl cl Adding or deleting a queue from the Ethernet Card port’s service list Changing the LPTl port’s name or configuration (this includes turning the configuration report on/off) Changing the master file server Setting the queue polling interval Setting the network configuration with EPCONFIG (setting the broadcast routing or the local address) Restoring factory defaults (with EPCONFIG) Caution: Once you reset the print server, you must wait for the “Reset has been completed” message to appear before turning off the printer, If you find resetting the Ethernet Card to be disruptive, see Answers to Common Questions in Chapter 3 for an alternative solution. Changing

  • Epson C82324*, d. Press INSERT to display a list of file servers. Select a file server upon which you have supervisor privilege. (Assigning a queue on a file server actually installs the print server on that file server. You can install the Ethernet Card on up to eight file servers.) e. Select one or more queues from the “Queue Name” list. Use the F5 key for multiple selections. You can create a new queue by pressing INSERT and entering a valid, unique queue name. Press ENTER to select queue(s). 10. After configuration, the LPT1 port is installed. 11. When you finish configuring ports, press ESC. Select “Yes�

  • Epson C82324*, Answers to Common Questions This section answers some of the most commonly asked questions about configuring and using the Ethernet Card. Avoiding Reboot with Print Server Status/Control How can I avoid having to reset my Ethernet Card print server after each configuration change? It’s disrupting users’ print jobs. If rebooting the Ethernet Card after configuration changes is inconvenient, you can use PCONSOLE’s Print Server Status/Control to create temporary configurations. Then use PCONSOLE’s Print Server Configuration to enter the same changes into the file server’s permanent database. Since t

  • Epson C82324*, In print server mode, this parameter is optional, unless your network uses a communication standard other than IEEE 802.3 or Ethernet II Novell type 8137, the two most common in Novell networks. When booted in print server mode, the Ethernet Card attempts to log into a file server using IEEE 802.3. If it cannot log in, it switches to Ethernet II Novell type 8137 and attempts to log in. If your network uses Ethernet II type 8135: you may want to configure the Ethernet Card so that the default network protocol is Ethernet II type 8137. (Because it no longer searches first for an 802.3 file server, the Ether

  • Epson C82324*, Troubleshooting Installation I’m trying to install the Ethernet Card, but after I enter the serial number, EPSETUP displays an “Unable to locate...serial number...” message. Did you enter the correct serial number? Is the Ethernet Cards host printer turned on? Is the network cable connected to the Ethernet Card? I’m installing the Ethernet Card as a remote printer, and EPSETUP displays a “port number is invalid” message when I enter a printer port number. Did you configure the printer port, and assign a queue to the po

  • Epson C82324*, Notice Before connecting this product to your NetWare ® v3.12 network, you need to add the IEEE 802.3 protocol. This step requires you to modify the server and your workstation settings. Change the settings for your server(s) and workstation(s) using the information below. 1. for all file servers using this product as their print You need to modify the file server’s AUTOEXEC.NCF file by adding the IEEE 802.3 protocol for the network card. The following example uses the Novell NE2000 network card. In this example, the network number for the IEEE 802.3 protocol is a38d2300, and the network number for the IEEE 802.2 protocol is a38d010

  • Epson C82324*, Turn Configuration Report Off/On EPCONFIG serial-number N=E RPT=NORP 1 RP Use this command to enable or disable configuration report printing. RP enables configuration report printing. Enter RPT=RP to enable configuration report printing. NORP disables configuration report printing. Enter RPT=NORP to disable configuration report printing. Example: EPCONFIG 06424922 N=E RPT=norp Set Queue Polling Interval (Print Server) EPCONFIG serial-number N=E T=polling_time Use this command to change the interval at which the parallel port(s) checks queues for waiting print jobs. To reduce network traffic, you can change the polling interval from the default (5 seconds) to up to 30 seconds. The po

Related Products and Documents (Network Card):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Murphy Low Pressure SWICHGAGE 20PWC Specifications murphy/low-pressure-swichgage-20pwc-2OT.pdf 18 Jan 2024 2
2 Daewoo DLT-42U1/G1HZ Instruction manual daewoo/dlt-42u1-g1hz-LF9.pdf 29 Aug 2023 58 3.88 Mb
3 OPENTEL ODT 1500C Operation & user’s manual opentel/odt-1500c-F36.pdf 13 Sep 2022 18
4 GE Profile PDW8280NSS Dimensions and installation information ge/profile-pdw8280nss-3H6.pdf 07 Dec 2022 2
5 AIRTRONICS 92451SR Operating instructions airtronics/92451sr-PY3.pdf 19 Oct 2023 2
6 Brother MFC9760 Parts reference list brother/mfc9760-H2K.pdf 17 May 2023 31 0.94 Mb

Similar Resources:

  • Linksys

    WPC54GR

    (2 pages)
    Model No.Quick InstallationA Division of Cisco Systems, Inc.®Model No.WirelessNotebook Adapter withWireless-G12CA The Network Adapter is installed and set up using the Setup Wizard that comes on the enclosed CD.B To begin, insert the Setup Wizard CD-ROM into your CD-ROM drive. The Setup Wizard should run automati-cally, and the Welcome screen should appear. …
  • HP

    Kayak XW U3-W3

    (16 pages)
    HP Kayak XW U3 & W3 PC Workstation Technical InformationThis section provides technical information about your PC Workstation and includes details about the system board connectors and switches. …
  • Gigabyte

    GA-K8N51PVMT-9-RH

    (88 pages)
    GA-K8N51PVMT-9-RHAMD Socket 939 Processor MotherboardUser's ManualRev. 100112ME-51PVMT9R-1001R* The WEEE marking on the product indicates this product must not be disposed of with user's other household wasteand must be handed over to a designated collection point for the recycling of waste electrical and electronic equipment!!* The WEEE marking ap …
  • ADTRAN

    NetVanta Series

    (6 pages)
    Technical Support 1-888-4ADTRAN (1-888-423-8726)NetVanta Series (with Serial Network Interface Module)Quick Configuration Guide 64200866L1-42C March 2005• V.35 or X.21 cable for connecting the system to the existing network.• VT100 terminal or PC with VT100 emulation software.• DB-9 (male) to DB-9 (female) straight-through cable for configuring the un …
  • Siemens

    SIMATIC PCS 7

    (136 pages)
    SIMATICProcess Control System PCS 7Advanced Process Functions Engineering ManualSystem Manual 07/2016A5E38719921-AAPrefaceSecurity information1APF Engineering at a glance2Configuring AS-OS communication3APF Engineering Tool4Material management5Storage management6Parameter management7Archive management8Additional steps for configuring9Diagnostics guide10 …
  • Panasonic

    2SA2161G

    (4 pages)
    Transistors1Publication date: May 2007 SJC00383AEDThis product complies with the RoHS Directive (EU 2002/95/EC).2SA2161GSilicon PNP epitaxial planar typeFor general amplificationComplementary to 2SC6037G■ Features• Low collector-emitter saturation voltage VCE(sat)• SS-Mini type package, allowing downsizing of the equipment andautomatic insertion throug …

Comments, Questions and Opinions: