Manualios.com

Epson C823301 Operation & User’s Manual

Epson C823301 Manual Online:

3.15, 2067 votes
Epson C823301 User Manual
Epson C823301 User Guide
Epson C823301 Online Manual

Text of Epson C823301 User Guide:

  • Epson C823301, Introduction This EPSON ® Fax Interface Board adds standalone plain paper fax reception to your EPSON laser printer. The Fax Interface Board is a G3 facsimile receiver and can be connected to any standard two-wire phone line. The Fax Interface Board can also serve as a Class 1 Fax modem connected to a computer’s serial interface if you use the proper fax software (which is not included in this package). After you install the board in your printer and connect it to an appropriate telephone line, you can receive faxes any time the printer is turned on and is on line, or while it is printing. The printer cannot receive faxes if it is off line or turned off. Printer

  • Epson C823301, Setup Setting up your fax board is a four-step process: 1. Set the DIP switches on the board. 2. Install the board in your printer. 3. Plug the appropriate cables into the board. 4. Perform a self test. Before you install your fax board, you need to make a number of choices about how your fax board will work. Read the descriptions below, make your choices, and then proceed with your setup. Fax reception modes This board has three fax reception modes: o Automatic reception-it starts to receive a fax when the ring signal is detected. o Selective reception-it starts to receive a fax either 15 or 30 seconds after it detects a ring signal (depending on the setting you sele

  • Automatic reception Select this mode if you use the fax board with a telephone line that you use exclusively for fax reception. If you select Automatic reception mode, the board receives faxes automatically any time fax data is received and the printer it turned on. If you wish, you can connect a telephone to the PHONE connector and place calls when the fax board is not receiving

  • Epson C823301, Manual or software reception Select this mode if you want to connect the fax board to your computer and use fax sending and receiving software or if you use the fax board with a telephone line that you usually use for voice calls. In this mode, you receive a fax using your fax software or in the following manner: 1. Answer the telephone connected to the fax board. 2. Push the manual reception button within 20 seconds after you hear the fax tone signal. 3. Hang up your telephone when the fax tone stops. You can make a telephone call or answer the phone any time the fax board is not receiving fax data. 4 Setup

  • Epson C823301, Once you have decided which fax reception setting you want, set the DIP switches according to the table below. This illustration shows the location of the switches; on is up and off is down. I ON OFF 1 I I L I I I Manual Reception Phone Telephone Serial Interface Button Line Fax reception settings I SWl-1 I SWl-2 I Functions OFF OFF Automatic reception mode (default) OFF ON ON OFF Selective reception mode (15 second delay) Selective reception mode (30 second delay) topview ON ON 1 Manual reception mode Setup 5

  • Epson C823301, There are three other settings you may want to change: Paper size The fax board can use either paper size shown below. SW 1-3 Functions I OFF Letter (default) ON A4 I Page overflow settings If the sending fax machine sends an extra-long page, the fax board can do either of the following: SW 1-6 Functions I 1 OFF I Print the overflow data to the next sheet (default) I ON Discard the overflow data Print data transfer speed The fax board transfers fax data to the printer very quickly. If the data transfer is too fast for the printer, a SET FULL PRINT error may occur on your printer. If this error happens frequently on your printer, reduce the duty perce

  • Epson C823301, Installing the fax board in your printer After you have set the DIP switches, install the fax board in your printer following the instructions in your printer manual. See the section on installing an optional interface board. Connecting the board After you have installed the board, connect the phone cable included with the board to the connector labeled LINE on the board. Plug the other end into a standard modular-type telephone connector (jack). If you wish, you can also plug a telephone into the connector labeled PHONE. Manual Reception to Phone Line to Telephone Serial Interface Butto

  • Epson C823301, Fax modem mode If you want to use the fax board to send faxes from your computer, you need to buy a straight through serial (or modem) cable and appropriate fax modem software. One cable is included with your fax board, but you need an additional cable to connect the board to your computer. You need a standard straight through (or modem) cable with a 25-pin connector on one end and a 9-pin connector (for the computer) on the other end or with 25-pin connectors on both ends, depending on the serial port of your computer. Check your computer before you buy the cable. When you have the appropriate serial cable, follow the steps below: 1. Connect the 9-pin connector of t

  • Epson C823301, Troubleshooting When the fax board cannot receive a fax The fax board has a 300KB buffer that allows it to store fax data when it can receive but not print. It can store up to 15 pages depending on the amount of text and graphics on each page. For example, it uses the buffer when it receives a fax while it is printing a standard print job sent by your computer. The fax board cannot, however, receive a fax under the following conditions: o When the buffer is full o When the printer is off line o When the phone line is already in use o When the printer is turned off. The fax board cannot begin reception if the printer is off line before the fax data star

  • Epson C823301, o Other errors that can be corrected without turning the printer off. After these printer errors are corrected, the fax board starts to print the received fax data automatically. When the fax board stops receiving a fax The fax board stops receiving fax data in the following situations: o Service request error (SERVICE REQ on printer’s LCD) o Fax reception buffer full o Fax sender quits sending the fax o Loss of phone line connection o Protocol mismatched between the fax board and the other fax machine. If one of these should occur, all or so

  • Epson C823301, Limitations EPL - 8000 users Set the following DIP switches if the fax board is installed in the EPL-8000. SW 2-l ON SW 2-2 OFF ActionLaser II users Set the printer emulation mode for the option interface card to the LJ-2 (Laser Jet) mode using SelecType. (See your printer manual for instructions on setting this mode.) EPSON GL ldentity Card (C826022) users Set the printer emulation mode from the option interface card to a mode other than the HP-GL mode using the control panel. (See your printer manual for instructions on setting the mode.) PostScript ® Card users Set the printer emulation mode for the option interface card to a mode other than the AUTO (AES; Auto Emul

  • Error Codes Error status report When an error occurs, the fax board prints a Fax Reception Error report, which includes an Error Code number. See the listing below for the meaning of the error code. Error code listing 1 Printer error I 100 I Printer off-line 101 Paper out 102 Paper jam 103 Toner out I 104 I Cover open 105 Service Request error 106 Paper size error Fax boar

  • Epson C823301, Technical specifications Facsimile reception Modem Facsimile V.29 9600bps, 7200bps V.27ter 4800bps, 2400bps T.30 (G3) Codec MH, MR Paper size A4, Letter (A4 mode on fax communication) Resolution Raster Feed 8.00 dot/mm 3.85 dot/mm (Normal) 7.70 dot/mm (Fine) NCU control Auto / Manual RX buffer 300KB RX pages 15 pages (constant / standard A4 test chart) Technical specifications 13

  • Epson C823301, Fax modem Modem V.29 9600bps, 7200bps V.27ter 4800bps, 2400pbs Modem commands EIA-578 (Fax class 1 compatible) Terminal speed NCU control 19200bps Auto / Manual Dial type Tone/Pulse Common specifications PTT line Two wires 3.4kHz type Line impedance 600ohm Rx signal level -15 to -35 dBm T X signal level -9 to -16 dBm (default -9dBm) EMI FCC part 15 class B PTT FCC part 68 (USA) IC CS-03 (Canada) 14 Technical specifications

  • Epson C823301, Connectors LINE (RJ-11: to telephone network) No. Signal I/O Comments 1 (N.C.) 2 (N.C.) 3 I PTT LINE (-48V / RING) 4 I PTT LINE ( EARTH / TIP) 5 (N.C.) 6 (N.C.) PHONE (RJ-11: to phone) No. Signal IlO Comments 1 (N.C.) 2 (N.C.) 3 0 PTT LINE (-48V / RING) 4 0 PTT LINE ( EARTH / TIP) 5 (N.C.) 6 (N.C.) SERIAL (MINI-DIN 9p: RS-232 to HOST PC) I: to the fax board 0: from the fax board Technical specifications 15

  • Serial interface cable PC side I/F card side Modular cable Serial cable DB-25 connector (DDK 17 JE-13250-02 compatible) Mini- DIN 9-pin (MSK EC-35-9P-C111 compatible) RJ-11 compatible Mini-DIN 9-pin to DB 25-pin 16 Technical specifcations

Related Products and Documents (Network Card):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 WFM 2000 S Operation & user’s manual wfm/2000-s-H2G.pdf 08 Oct 2022 72
2 Tripp Lite USA-49WG Owner's manual tripp-lite/usa-49wg-9VC.pdf 21 Jun 2023 37 4.13 Mb
3 Philips AJL303/12 Operation & user’s manual philips/ajl303-12-JI7.pdf 08 Jul 2023 18 0.67 Mb
4 Jenn-Air DUAL-FUEL SLIDE-IN RANGE Operation & user’s manual jenn-air/dual-fuel-slide-in-range-272.pdf 10 Mar 2023 64
5 Ectaco Partner ER900 Operation & user’s manual ectaco/partner-er900-322.pdf 05 Apr 2023 47 2.1 Mb
6 Sony AITi200STS Specifications sony/aiti200sts-9UN.pdf 26 Sep 2022 2 0.17 Mb

Similar Resources:

  • Radio Shack

    Enercell 273-329

    (1 pages)
    TMMT13.5/30VDC • 1A AC-to-DC Power Adapter 273-329Cautions:• If this adapter is not compatible with the voltage and current requirements of your portable device, it can result in PERMANENT DAMAGE to the device.• Before using, consult the User’s Guide or the rating label on your device to make sure it requires 13.5 or 30 volts DC.• The power ad …
  • Roland

    TD-12

    (44 pages)
    SERVICE NOTES Issued by RJA Copyright © 2005 ROLAND CORPORATION All rights reserved. No part of this publication may be reproduced in any form without the written permission of ROLAND CORPORATION. Printed in Japan (0500) (AS)17058329E0 Apr.2005TD-12 TABLE OF CONTENTS SPECIFICATIONS.............................................................2LOCATION OF CO …
  • Ken A Vision

    7700

    (2 pages)
    Video Flex 7700Network CameraVideo Flex 7700Network CameraAn image is generated and transmitted over the network by the Video Flex Network Camera in thisclassroom (A).RJ45 JackThrough the network connection thedemonstration from the Video Flex in A is being projected onto a screen in this classroom.Through the network connectionthe demonstration from the Vid …
  • Chicago Pneumatic

    CS7000

    (46 pages)
    December 2005 iCS7000 ControllerHardware Overview ManualWith Ethernet/CCM Informationfor use with177 and 277 Series Electric Fastening ToolsCP Ref. / NO : 6159939130Techmotive P/N : 39-30-41365December 2005CP Techmotive22705 Heslip DriveNovi, Michigan 48375 USA6159939130 …
  • RLH Industries

    10M ETHERNET

    (10 pages)
    ! RLH Industries, Inc. • Tel. 866-DO-FIBER • Fax 714 532-1885 • www.fiberopticlink.com! Page 1Ethernet Over Fiber4RU Plug-in Card10/100/1000M ETHERNETIntroductionThe RLH 10/100/1000 Ethernet 4RU Interface Card converts a copper 10Base-T or 100/1000Base-TX to a 1000Base-SX/LX fiber optic transmission signal of either multimode or s …
  • Abocom

    802.11b Wireless Short PC Card Wb1500S

    (1 pages)
    Wb1500S802.11b Wireless Short PC CardThe 802.11b Wireless Short PC Card is a card that lets you connect your notebook to a wireless local area network (LAN). A wireless LAN is like a regular LAN, except that you can share information without looking for a place to plug in, and augment networks without installing or moving wires. Based on radio frequency (R …

Comments, Questions and Opinions: