Manualios.com

Epson Ethernet Card Supplement Manual

Epson Ethernet Card Manual Online:

3.8, 1258 votes
Epson Ethernet Card User Manual
Epson Ethernet Card User Guide
Epson Ethernet Card Online Manual

Text of Epson Ethernet Card User Guide:

  • Epson Ethernet Card, EPSON ® Ethernet Card Supplement This guide includes new information about your EPSON ® multiprotocol Ethernet interface card and software. If you are using the card with Apple ® Macintosh a computers on AppleTalk ® or TCP/IP networks, please disregard the Macintosh section in your EPSON Type B Ethernet Interface Card User's Guide and follow the steps in this supplement. In addition to the operating systems mentioned in the Ethernet card User’s Guide, the card also supports Windows 95 and Windows NT 4.x. You’ll find the following information in this Supplement: CI

  • Initializing the Ethernet Card After you install the Ethernet card in a printer or reinstall it in a new printer, plug in the printer while pressing down the status sheet button for at least three seconds to initialize the card. I I 0: ,.Ds @ I I I I status sheet button Printing a Status Sheet You can print a status sheet after you finish initializing the card.

  • Epson Ethernet Card, Using Macintosh with the Ethernet Card Before configuring the Ethernet card, check to see if the correct printer driver is installed in the Macintosh. Make sure the printer is turned on and the Ethernet card is connected to the network. (See your Ethernet card User’s Guide and your printer User’s Guide for more information.) The information on Macintosh is explained in the following sections: Ct Installing EPSON Net! Ll Monitoring the Printers on Your Network Ll Configuring the Ethernet Card for AppleTalk Cl Configuring the Ethernet Card for TCP/IP Using EPSON Net! for Macintosh Note: lf you are using Macintosh computers on a NetWare

  • Epson Ethernet Card, To check the status of all printers that are turned on and enabled for a protocol, follow the steps below: 1. Open the EPSON Net! folder and click the EPSON Net! icon. The following window appears: Note: If you don‘t see any printers in the list, try selecting the zone that the printer is in or all zones by following the steps in the next section. 2. To exit EPSON Net!, click Quit. Selecting a Zone You can select which printers to monitor according to their zone or address. You must select a zone before you configure the Ethernet card in the Configuration dialog box. Follow these steps: 1. With the EPSON Net! dialog bo

  • 2. Click a zone to select it, press and hold the Shift key while clicking multiple zones to select them, or click Select All. 3. Click OK. EPSON Net! sends a packet to the selected zones and detects the current printer’s status. The EPSON Net! dialog box shows the latest information about the printers located in that zone. Sorting the Printers Follow these steps to sort the pri

  • Epson Ethernet Card, Setting the Refresh lnterval Follow these steps to set the refresh interval for the settings in the EPSON Net! dialog box: 1. With the EPSON Net! dialog box open, choose Preferences from the Options menu bar. Refresh interval (sec) pq (DKI [Cancel) 2. Type any value from 5 (default) to 90 seconds and click OK. EPSON Net! monitors the printers by polling the network at the intervals you specified. Configuring the Ethernet Card for AppleTalk Follow these steps to use EPSON Net! for Macintosh to configure the Ethernet card for AppleTalk: Note: You must select a zone before yo

  • Epson Ethernet Card, 2. Highlight the printer you want to configure in the list. 3. Click Open. You see the Configuration dialog box: 4. Click the AppleTalk icon. Make sure the correct serial number of your Ethernet card is displayed. 5. Set the following options in the AppleTalk Configuration box: CL Available Zone: Select the network zone that you want the printer to appear in. Ll Printer Name: The default printer name appears. You can rename it. If the same types of printers are connected to the network, be sure to give them unique names. Ll Entity Type: EPSON Net! displays the printer’s Entity type on an AppleTalk network. You don’t have t

  • Epson Ethernet Card, 6. Click OK to send the new settings to the Ethernet card and return to the EPSON Net! dialog box. Click Update to send the new settings to the card without closing the Configuration dialog box. Caution: Once you make changes to the Ethernet card, wait at least five minutes before turning off or restarting your printer. 7. Click Exit to exit EPSON Net! for Macintosh. Configuring the Ethernet Card for TCP/IP Using EPSON Net! for Macintosh To configure the Ethernet Card for TCP/IP using EPSON Net! for Macintosh, follow these steps: 1. Open the EPSON Net! folder and double-click the EPSON Net! icon. Note: If you do not know

  • Epson Ethernet Card, 4. Click the TCP/IP icon. Make sure the Configuration dialog box shows the correct serial number of the target Ethernet card. 5. Set the following options in the TCP/IP Configuration dialog box: U IP address: Determine and assign an IP address for the Ethernet card. Q Subnet mask: Assign the subnet mask. tl Auto IP set: Click Off. 6. Click Update to send the new settings to the Ethernet card without closing the Configuration dialog box. Or, click OK to send the new settings and return to the EPSON Net! dialog box. 7. Click Exit to exit EPSON Net! for Macintosh. After configuring the Ethernet card for TCP/IP, set up your printer on each Macintosh an

  • Epson Ethernet Card, 4. Click Protocol and then the Add button. 5. Select Microsoft from the Manufacturers list and TCP/IP from the Network Protocols list. Then click OK. 6. Click OK again and follow any on-screen instructions to enable TCP/IP. Configuring the Ethernet Card for TCP/IP and Windows 95 Make sure that the Ethernet card installed in the printer is on the same network segment as the computer you are using to configure the card. Also, find out that computer’s IP address and the IP address that you will assign to the Ethernet card. Note: lf you do not know how to find out your computer’s IP address or the IP address for the Ethernet card, ask your network administr

  • Epson Ethernet Card, ping <IP address> for example: ping 127.0.1.200 You see a message similar to the following: Reply from 127.0.1.200: bytes=32 time<10ms TTL=30 Reply from 127.0.1.200: bytes=32 time<10ms TTL=30 Reply from 127.0.1.200: bytes=32 time<l0ms TTL=30 Reply from 127.0.1.200: bytes=32 time<l0ms TTL=30 This shows that the Ethernet card is set up for TCP/IP correctly. If you receive 4 lines of “Request Timed Out,” The card is not set up correctly. Check to make sure the card is on the same network segment as the workstation you are using to configure it and that you typed in the correct IP and hardware add

  • Epson Ethernet Card, EPSON is a registered trademark of SEIKO EPSON CORPORATION. General Notice: Other product names used herein are for identification purposes only and may be trademarks of their respective owners. EPSON disclaims any and all rights in those marks. I Copyright 0 1997 by Epson America, Inc. 10/97 6B Printed on recycled paper with at least 10% post-consumer content.

Related Products and Documents (Network Card):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Stacey i4 Operating instructions manual stacey/i4-Z79.pdf 22 Aug 2023 14
2 Cadet CM162 Owner's manual cadet/cm162-A2D.pdf 31 Jul 2022 12
3 HTC One X Operation & user’s manual htc/one-x-D53.pdf 11 Aug 2022 182
4 Dacor EHD3018 Installation instructions manual dacor/ehd3018-14G.pdf 18 Mar 2023 8
5 Toshiba RAS-M154GAV-E Owner's manual toshiba/ras-m154gav-e-46T.pdf 10 Aug 2023 24
6 ASROCK iBOX-210 Operation & user’s manual asrock/ibox-210-ZH7.pdf 23 Dec 2023 30 2 Mb

Similar Resources:

  • ZyXEL Communications

    P-870HW-51A V2

    (12 pages)
    www.zyxel.comP-870HW-51a v2802.11bg Wireless VDSL2 4 port gateway Firmware v1.00Edition 1, 12/2008DEFAULT LOGIN DETAILSIP Address: http://192.168.1.1Username: 1234Password: 1234Copyright 2008ZyXEL Communications CorporationC …
  • D-Link

    DCM-100

    (18 pages)
    DCM-100 DOCSIS 1.0 Ethernet Cable Modem User’s Manual First Edition (April 2001) 6DCM200...01 Printed in Taiwan RECYCLABLE …
  • Connect Tech

    Titan/cPCI

    (34 pages)
    Titan/cPCI CompactPCI Serial Communications User Manual Connect Tech Inc 42 Arrow Road Guelph, Ontario N1K 1S6 Tel: 519-836-1291 Toll: 800-426-8979 (North America only) Fax: 519-836-4878 Email: [email protected] [email protected] URL: www.connecttech.com CTIM-00009, Revis …
  • TP-Link

    TL-PA8010P

    (5 pages)
    AV1300 Gigabit Passthrough Powerline Starter Kit TL-PA8010P KITSmooth Ultra HD Streaming in Every Room2x2 MIMO TechnologyHomePlug AV2 1300MbpsPlug, Pair and Play …
  • Delta Electronics

    Pulse Generation Unit DVP01PU-H2

    (2 pages)
    1. Warning  This instruction sheet provides information on the installation, wiring and trial operation of DVP01PU-H2. For more detailed information, see “DVP-PLC Application Manual: Special Module”.  DO NOT touch any terminal when the power is switched on. Switch off the power before wiring.  DVP01PU-H2 is an OPEN-TYPE device and therefore …
  • D-Link

    DWL-G630 - AirPlus G 802.11g Wireless PC Card

    (12 pages)
    1AirPlus™ G 802.11g/2.4GHz Wireless Cardbus AdapterDWL-G630©2003 D-Link Systems, Inc. All rights reserved. Trademarks or registered trademarks are the property of their respective holders.Software and specifications subject to change without notice. DWL-G630.04232004If any of the above items are missing, please contact your reseller.CD-ROM (containing Dri …

Network Card Instructions:

Comments, Questions and Opinions: