Epson ELPLL02 Operation & User’s Manual
|
Epson ELPLL02, 18 4. Rear-projection wide-angle lens specifications 4-1 Lens specifications 1. Focal length 27mm 2. f number 2.3 3. Projection size 60 to 100 inches 4. Mass 1600 g 4-2 Appearance with rear projector wide lens mounted About 455mm 01.2.15, 4:17 PMPage 18
Epson ELPLL02, 13 (2) Mounting the front case 1. Set the front case into position and tighten the two screws. This completes installation. • Turn on the power and verify that the projector operates nor- mally. Memo Be sure to remove the front lens cap before turning on the power, or it may melt from the heat. 01.2.15, 4:20 PMPage 13
Epson ELPLL02, 13 (2) Mounting the front case 1. Set the front case into position and tighten the two screws. This completes installation. • Turn on the power and verify that the projector operates nor- mally. Memo Be sure to remove the front lens cap before turning on the power, or it may melt from the heat. 01.2.15, 4:23 PMPage 13
Epson ELPLL02, 9 User’s Manual for ELPLS01 Standard Lens • This standard lens is designed for use only with EPSON multimedia pro- jectors. • Please read this manual completely before use to assure maximum per- formance. • Note that illustrations may differ slightly from your actual product. • Specifications are subject to change without notice. Safety Precautions To assure that this product is used safely, and to help prevent dam- age or injury, the following symbols are used in the manual. Please read this manual thoroughly before use to ensure safety and opti- mum performance. Warning Ignoring this warning, or implementing the content in- correctly, could result in injur
Epson ELPLL02, 16 (3) Mounting the front case 1. Set the front case into position and tighten the two screws. This completes installation. • Turn on the power and verify that the projector operates nor- mally. 01.2.15, 4:17 PMPage 16
Epson ELPLL02, 11 User’s Manual for ELPLR01 Rear Projector wide Lens • This wide-angle lens is designed for use only on EPSON multimedia projectors. • This lens is designed for use only on rear projection and rear projection box systems. • Please read this manual completely before use to assure maximum per- formance. • Note that illustrations may differ slightly from your actual product. • Specifications are subject to change without notice. Safety Precautions To assure that this product is used safely, and to help prevent dam- age or injury, the following symbols are used in the manual.
Epson ELPLL02, 11 2. Mounting the zoom lens Warning Be sure to disconnect the power cable before installa- tion, because there is danger of electrical shock. Memo Always mount and dismount the lens in a clean room, to minimize the amount of dust. Excessive dust inside the lens could cause damage. • Note that the illustrations below may not match your par- ticular projector model. Front case Screws (three) 2-1 Removing the current lens (1) Remove the front case. 1. Remove the three mounting screws, and pull off the
Epson ELPLL02, 12 (2) Remove the current lens. 1. Use the enclosed screwdriver to remove the four mounting screws, and dismount the current lens. 2-2 Mounting the zoom lens (1) Mounting the zoom lens 1. Remove the rear lens cap. 2. Use the enclosed screwdriver to mount the zoom lens with the four mounting screws. Be sure that the seal reading “UPPER” is on top. Current lens Seal Rear lens cap 01.2.15, 4:23 PMPage 12
Epson ELPLL02, 11 2. Mounting the zoom lens Warning Be sure to disconnect the power cable before installa- tion, because there is danger of electrical shock. Memo Always mount and dismount the lens in a clean room, to minimize the amount of dust. Excessive dust inside the lens could cause damage. • Note that the illustrations below may not match your par- ticular projector model. Front case Screws (two) 2-1 Remove the current lens (1) Remove the front case. 1. Remove the two mounting screws, and pull off the front case. 01.2.15, 4:23 PMPage 11
Epson ELPLL02, 9 User’s Manual for ELPLL02 Long-Focal Length Zoom Lens • This long-focal length zoom lens is designed for use only with EPSON multimedia projectors. • It makes it possible to increase the distance between the projector and the screen. • Please read this manual completely before use to assure maximum per- formance. • Note that illustrations may differ slightly from your actual product. • Specifications are subject to change without notice. Safety Precautions To assure that this product is used safely, and to help prevent dam- age or injury, the following symbols are used in the manual.
12 1. Before mounting the wide-angle lens 1-1 Safety precautions Warning Be sure to screw the Rear Projector wide lens and adapter ring down completely. Unless they are securely screwed on, they could fall off and cause damage or injury (especially when the projector is ceiling-mounted). 1-2 Check product contents • Make sure that you have all the parts, as shown below, before startin
Epson ELPLL02, 11 2. Mounting the zoom lens Warning Be sure to disconnect the power cable before installa- tion, because there is danger of electrical shock. Memo Always mount and dismount the lens in a clean room, to minimize the amount of dust. Excessive dust inside the lens could cause damage. • Note that the illustrations below may not match your par- ticular projector model. Front case Screws (two) 2-1 Removing the current lens (1) Remove the front case. 1. Remove the two mounting screws, and pull off the front case. 01.2.15, 4:20 PMPage 11
Epson ELPLL02, 10 1. Before mounting the zoom lens 1-1 Safety precautions Warning Be sure to screw the Long-Focal Length lens and adapter ring down completely. Unless they are securely screwed on, they could fall off and cause damage or injury (especially when the projector is ceiling-mounted). 1-2 Check product contents • Make sure that you have all the parts, as shown below, before starting. • In addition to the included screwdriver, you will also need a Phillips screwdriver, and various other common tools. Memo Be sure to use a Phillips screwdriver that fits the screws properly. Rear lens cap User’s manual (this document) Zoom lens Front lens cap Used to tighter/remove mounting screws Scre
Epson ELPLL02, 15 4. Zoom lens specifications 4-1 Lens specifications 1. Focal length 68.3 to 116.2 mm 2. Zoom ratio 1.7 x 3. f number 2.14 to 2.98 4. Projection size 60 to 300 inches 5. Mass 2100 g 4-2 Appearance with zoom lens mounted About 505mm 01.2.15, 4:20 PMPage 15
10 1. Before mounting the zoom lens 1-1 Safety precautions Warning Be sure to screw the Long throw zoom lens and adapter ring down completely. Unless they are securely screwed on, they could fall off and cause damage or injury (es- pecially when the projector is ceiling-mounted). 1-2 Check product contents • Make sure that you have all the parts, as shown below, before starting. • In addition
15 4. Standard lens specifications 4-1 Lens specifications 1. Focal length 49.2 to 68.9 mm 2. Zoom ratio 1.4 x 3. f number 1.84 to 2.36 4. Projection size 30 to 300 inches 5. Mass 1300 g 4-2 Appearance with standard lens mounted About 475mm 01.2.15, 4:19 PMPage 15
Epson ELPLL02, 12 (2) Remove the current lens. 1. Use the enclosed screwdriver to remove the four mounting screws, and dismount the current lens. 2-2 Mounting the zoom lens (1) Mounting the zoom lens 1. Remove the rear lens cap. 2. Use the enclosed screwdriver to mount the zoom lens with the four mounting screws. Be sure that the seal reading "UPPER" is on top. Current lens Seal Rear lens cap 01.2.15, 4:22 PMPage 12
15 4. Zoom lens specifications 4-1 Lens specifications 1. Focal length 144.1 to 194.5mm 2. Zoom ratio 1.35 x 3. f number 2.60 to 3.27 4. Projection size 80 to 300 inches 5. Mass 2100 g 4-2 Appearance with zoom lens mounted About 505mm 01.2.15, 4:23 PMPage 15
Epson ELPLL02, 10 1. Before mounting the zoom lens 1-1 Safety precautions Warning Be sure to screw the Long-Focal Length lens and adapter ring down completely. Unless they are securely screwed on, they could fall off and cause damage or injury (especially when the projector is ceiling-mounted). 1-2 Check product contents • Make sure that you have all the parts, as shown below, before starting. • In addition to the included screwdriver, you will also need a Phillips screwdriver, and various other common tools. Memo Be s
Epson ELPLL02, 13 (2) Mounting the front case 1. Set the front case into position and tighten the two screws. This completes installation. • Turn on the power and verify that the projector operates nor- mally. Memo Be sure to remove the front lens cap before turning on the power, or it may melt from the heat. 01.2.15, 4:19 PMPage 13
Epson ELPLL02, 14 Rear lens cap (2) Remove the current lens. 1. Use the enclosed screwdriver to remove the four mounting screws, and dismount the current lens. 2-2 Mounting the rear-projection wide-angle lens (1) Mounting the rear-projection wide-angle lens 1. Remove the rear lens cap. 2. Use the enclosed screwdriver to mount the rear projector wide lens with the four mounting screws. Be sure that the seal read- ing “UPPER” is on top. Current lens Seal 01.2.15, 4:17 PMPage 14
Epson ELPLL02, 11 2. Mounting the standard lens Warning Be sure to disconnect the power cable before installa- tion, because there is danger of electrical shock. Memo Always mount and dismount the lens in a clean room, to minimize the amount of dust. Excessive dust inside the lens could cause damage. • Note that the illustrations below may not match your par- ticular projector model. Front case Screws (two) 2-1 Removing the current lens (1) Remove the front case. 1. Remove the two mounting screws, and pull off the front case. 01.2.15, 4:19 PMPage 11
Epson ELPLL02, 9 User’s Manual for Long Throw Zoom Lens ELPLL03 • This long throw zoom lens is designed for use only with EPSON multi- media projectors. • It makes it possible to increase the distance between the projector and the screen. • Please read this manual completely before use to assure maximum per- formance. • Note that illustrations may differ slightly from your actual product. • Specifications are subject to change without notice. Safety Precautions To assure that this product is used safely, and to help prevent dam- age or inju
Epson ELPLL02, 13 (2) Mounting the front case 1. Set the front case into position and tighten the three screws. This completes installation. • Turn on the power and verify that the projector operates nor- mally. Memo • Be sure to remove the front lens cap be- fore turning on the power, or it may melt from the heat. • When handling the zoom lens, take care not to catch your finger between the lens and the tabletop. 01.2.15, 4:22 PMPage 13
Epson ELPLL02, 15 4. Zoom lens specifications 4-1 Lens specifications 1. Focal length 37.9 to 45.5 mm 2. Zoom ratio 1.2 x 3. f number 2.34 to 2.65 4. Projection size 60 to 200 inches 5. Mass 2600 g 4-2 Appearance with zoom lens mounted About 480mm 01.2.15, 4:22 PMPage 15
15 (2) Adjusting the wide lens for a rear projector • This lens must be adjusted to match the screen size. Adjust the lens as follows, before installing the front case. 1. Turn the lens shift button to move the lens all the way down. 2. Loosen the 2 focus ring mounting screws by using the hex wrench that came in the same package. 3. Loosen the 2 resolving pl
Epson ELPLL02, 10 1. Before mounting the standard lens 1-1 Safety precautions Warning Be sure to screw the Long-Focal Length lens and adapter ring down completely. Unless they are securely screwed on, they could fall off and cause damage or injury (especially when the projector is ceiling-mounted). 1-2 Check product contents • Make sure that you have all the parts, as shown below, before starting. • In addition to the included screwdriver, you will also need a Phillips screwdriver, and various other common tools. Memo Be sure to use a Phillips screwdriver that fits the scr
Epson ELPLL02, 9 User's Manual for the ELPLW01 Wide Zoom Lens • This wide zoom lens is designed for use only with EPSON multimedia projectors. • It makes it possible to decrease the distance between the projector and the screen. • Please read this manual completely before use to assure maximum per- formance. • Note that illustrations may differ slightly from your actual product. • Specifications are subject to change without notice. Safety Precautions To assure that this product is used safely, and to help prevent dam- age or injury, the following symbols are used in the manual. Please read this manual thoroughly before use to ensure safety and opt
Epson ELPLL02, 12 (2) Remove the current lens. 1. Use the enclosed screwdriver to remove the four mounting screws, and dismount the current lens. 2-2 Mounting the standard lens (1) Mounting the standard lens 1. Remove the rear lens cap. 2. Use the enclosed screwdriver to mount the standard lens with the four mounting screws. Be sure that the seal reading “UP- PER” is on top. Current lens Seal Rear lens cap 01.2.15, 4:19 PMPage 12
Epson Stylus COLOR 1160 Projector Accessories Service manual
Stylus COLOR 1160 |
Epson Stylus C40S Projector Accessories Product information sheet
Stylus C40S |
Epson PictureMate 100 Projector Accessories Manual
PictureMate 100 |
Epson Artisan 810 Projector Accessories Specifications
Artisan 810 |
Epson AcuLaser CX11N Projector Accessories Update
AcuLaser CX11N |
Epson PowerLite Home Cinema 3020e Projector Accessories Notice
PowerLite Home Cinema 3020e |
Epson 1810p - PowerLite XGA LCD Projector Projector Accessories Parts list
1810p - PowerLite XGA LCD Projector |
Epson PowerLite 1725 Projector Accessories Operation & user’s manual
PowerLite 1725 |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | Samsung | SGH-i728 | Operation & user’s manual | samsung/sgh-i728-5Q9.pdf | 07 Nov 2022 | 85 | |
2 | Motorola | MOTOTRBO XiR M8260 | Operation & user’s manual | motorola/mototrbo-xir-m8260-2WI.pdf | 01 Oct 2022 | 114 | |
3 | SOYO | SY-K7VMP2 | Quick start manual | soyo/sy-k7vmp2-M49.pdf | 10 Jul 2023 | 33 | 1.79 Mb |
4 | Roadstar | CLR-2615 | Operation & user’s manual | roadstar/clr-2615-ONG.pdf | 25 Apr 2023 | 32 | |
5 | Sony | STR-DE695 - Fm Stereo/fm-am Receiver | Dimensions | sony/str-de695-fm-stereo-fm-am-receiver-SP4.pdf | 04 Aug 2022 | 1 | 0.06 Mb |
6 | LENCO | DVP-736 | Operation & user’s manual | lenco/dvp-736-GLJ.pdf | 26 Apr 2023 | 12 |
PEERLESS
ISSUED: 07-31-01 SHEET #: 055-9029-5 08-05-04Visit the Peerless Web Site at www.peerlessindustries.com For customer service call 1-800-729-0307 or 708-865-8870.1 of 2IMPORTANT! Read entire instruction sheetbefore you start installation and assembly.Installation and Assembly - Universal Projector MountModels: PAP 40, PAP 40-S, PAP 40-WPAP 45, PAP 45-S, PAP …
PAP 40(2 pages) |
Screen Technics
1IN AUSTRALIAPROUDLY BUILTContinued Over.../INSTRUCTIONS - INTERFIT PROJECTOR LIFT – FVI and HTI SeriesThank you for purchasing a Screen Technics AV Lifter and please ensure to read the instruction fully before proceeding to install the unit.GENERAL ADVICE• The Intert AV Lifter is a fully integrated unit that is designed to be installed above the cei …
INTERFIT FVI Series(11 pages) |
Wize
Wize PL80(L), PL120(L), PL 150(L) Motorized projector lifts INSTALLATION/OPERATION INSTRUCTION Wize – high-quality mount solutions for audio-video installations Motor Lift hanger Lift top plate Running belt Stabilizing aluminum scissor Screw pole Capacitor (Junction box) Lift top plate Projector Lift bottom plate Universal projector bracket (optiona …
PL80(12 pages) |
InFocus
Replacing the projection lampThe lamp hour timer in the About menu counts the number of hours the lamp has been in use. Fifty hours before the specified end of the lamp’s life, the message “Replace lamp” briefly appears on the screen at each startup and in the Interactive Display. After 50 additional hours, the lamp will no longer light. You can order …
LP540(2 pages) |
Navitar
ROCHESTER, NEW YORK UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES AND INCLUDE CHEMICALLY APPLIED OR PLATED FINISHES0.0 inch 1.00.0 mm 25.0SIZE REVSCALE:DR:CH:PROJECT #:DATE DR:DO NOT SCALE DRAWINGSHEET OFTHE CONTENTS OF THISDOCUMENT ARE PROPRIETARYTO NAVITAR, ITS USE ISAUTHORIZED ONLY FORRESPONDING TO REQUEST FORQUOT …
SSC065(1 pages) |
Epson
INSTALLATION MANUALHigh Security Projector Ceiling MountMODEL# ELPMBATAManufactured by:Business Machine Security, Inc.520 W. Central Ave.Brea, CA 92821www.LocDown.com
…
ELPMBATA - High Security - Mounting(11 pages) |
Samsung Computer Hardware S3C2416#R78FU3: S3C2416 Computer Hardware Operation & user’s manual S3C2416, 672 |
Nortel Software Viewer#YC1181 Viewer: Nortel Software Owner Documentation Viewer, 100 |
Electromotive Automobile Accessories xdiUser Manual: Electromotive xdi (8X491R, Upd.23.02.2024) xdi, 36 |
Hunter Fan 23921#N142Q2: 23921 Fan Manual de installatión y operatión 23921, 14 |
Outback Grill THG2302P-3Outback Product User Manual: THG2302P-3 PDF Operating instructions manual - 62F42Y THG2302P-3, 18 |
Quantum Network Router TC2201Operation & user’s manual for Quantum TC2201 Network Router TC2201, 164 |
Fujitsu Storage MAU3036RC SERIESFujitsu Storage Product/maintenance manual (File: fujitsu-mau3036rc-series-product-maintenance-manual-92, Thu 10.2023) MAU3036RC SERIES, 92 |
HIKVISION Camcorder DS-2CM232P/NPDF Manual (@57XSSJ), HIKVISION DS-2CM232P/N Camcorder (12/11/2023) DS-2CM232P/N, 6 |
Trane Air Conditioner RT-DS-10Trane Air Conditioner RT-DS-10 Features & benefits manual RT-DS-10, 44 |
Bg Speakers PD-6Ci#686R2U PD-6Ci: Bg Speakers Owner Documentation PD-6Ci, 2 |
Samsung Laptop SENS 820 SERIESSamsung SENS 820 SERIES User Manual (Doc Type: Laptop Service manual) SENS 820 SERIES, 74 |
Philips Coffee Maker HD7400/20PDF Guide (@7T7WIX), Philips HD7400/20 Coffee Maker (Fri 01.2024) HD7400/20, 64 |