Epson POWERLITE HOME 10+ CPD-1790-4R2 Operation & User’s Manual
|
Epson POWERLITE HOME 10+ CPD-1790-4R2, 27 Cleaning and Replacing the Air Filter Clean the air filter on the bottom of the projector after every 100 hours of use. If it’s not cleaned periodically, it can become clogged with dust, preventing proper ventilation. This can cause overheating and damage the projector. 1. Turn off the projector and wait for the P power light to stop flashing. 2. Unplug the power cord and disconnect any cables. 3. Turn the projector over. Then use a small vacuum cleaner designed for computers and other office equipment to clean the filter, as
Epson POWERLITE HOME 10+ CPD-1790-4R2, 19 1. Press the Menu button. You see the menu screen. 2. Press the Select button to select the Image menu. Then press the Select button again to select Picture Quality. 3. Use the arrow buttons on the remote control or the , , or buttons on the projector to set the following options: ■ Brightness Adjusts the brightness of the picture. Increase (+) the setting to make the picture brighter, or decrease (-) the setting to reduce brightness. ■ Contrast Adjusts the contrast between col
Epson POWERLITE HOME 10+ CPD-1790-4R2, 20 ■ Theatre For projecting movies or images with dark scenes. ■ Theatre Black For projecting in a dark room; lamp brightness decreases and image contrast increases. 5. To save the adjustments you made in the Image menu, select the Memory option. Select Memory 1 to save your first set of adjustments. Later you can recall these settings by pressing the Memory button on the remote control. Note: You can save a second set of adjustments by selecting Memory 2. Press the Memory button on the remote control twice to select this second set. 6. Press Esc or Menu
28 Replacing the Lamp The lamp lasts up to 3000 hours when the projector is used in Theatre Black mode. Lamp life results vary depending upon environmental conditions and usage. Turn the projector off when not in use. Continuous 24-hour-a-day use may reduce the overall life of this product. It’s time to replace the lamp when: ■ The projection image gets darker or starts to deter
Epson POWERLITE HOME 10+ CPD-1790-4R2, 32 The warning light is flashing orange. High-speed cooling is in process. If the projector gets too hot again, projection stops automatically. Make sure there is plenty of space around and under the projector for ventilation. Clean or replace the air filter if necessary. See page 27 for details. The warning light is red. The projector is too hot, which turns off the lamp automatically. Let it cool for five minutes, then turn it back on. Make sure there is plenty of space around and under the projector for ventilation. Also, clean or replace the filter if necessary. See page 27. The warning light
Epson POWERLITE HOME 10+ CPD-1790-4R2, 30 Resetting the Lamp Timer 1. Press the Menu button on the projector or remote control. 2. Highlight the Reset menu and press the Select button. 3. Select Lamp Hours Reset. 4. When you see a prompt asking whether you want to execute the command, highlight Yes and press the Select button. 5. When you’re finished, press Esc or Menu. The lamp usage timer doesn’t register until you’ve used the lamp for at least 10 hours. Storing the Projector If you need to store the projector for awhile, do the following: ■ Make sure the temperature a
Epson POWERLITE HOME 10+ CPD-1790-4R2, 23 Viewing Lamp Usage and Other Information Use the Info menu to view information about the display settings of your input source and the number of hours the lamp has been used. 1. Press the Menu button to display the menu screen. 2. Press the down arrow button on the remote control or the button on the projector to highlight the Info menu. Then press Select. If the projector is connected to video equipment, you see these settings: If the projector is connected to a computer, you see these settings: The life span of the lamp is about 3000 hours if the color mode is consistently set to Thea
Epson POWERLITE HOME 10+ CPD-1790-4R2, 22 6. Select the On Screen Display option to make changes to these settings: ■ Message Turn this option off if you don’t want to display the No Signal message or the name of the input source or color mode. Warning messages are still displayed. ■ Background Color Selects the screen color to display (blue or black) when you press the A/V Mute button on the remote control. ■ Startup Screen Turn on this option to display the Epson logo whenever the projector starts. 7. Select the Input Signal option to co
Epson POWERLITE HOME 10+ CPD-1790-4R2, 3 Contents Important Safety Information 5 Remote Control Information 6 Presenting the Epson PowerLite Home 10+ 7 Registration and Warranty 7 Projector Parts 8 Projection Controls 9 Using This Manual 10 Getting More Information 10 Supported Devices 11 Cable Requirements 11 Optional Accessories 12 Using the Projector 13 Choosing a Location 13 Adjusting the Picture 14 Adjusting the Volume 16 Turning Off the Picture and Sound 16 Freezing the Action 16 Using the Projector’s Menu System 17 Changing Menu Settings 17 Adjusting the Appearance of the Picture 18 Customizing Projector Operation 20 Repositioning the Picture 22 Viewing La
Epson POWERLITE HOME 10+ CPD-1790-4R2, 13 Using the Projector Follow the instructions in this section to choose a location for the projector, adjust the image and volume, turn off picture and sound, freeze the action, or use the projector menus. Choosing a Location The distance from the projector to the screen or wall determines the size of the picture. The picture will be larger when you place the projector further from the screen. See the Quick Setup sheet for details about the relationship between distance and picture size. You can also choose from five differ
Epson POWERLITE HOME 10+ CPD-1790-4R2, 38 Dimensions Height 4.5 inches (114 mm) Width 15.8 inches (402 mm) Depth 11.6 inches (294 mm) Weight 7.9 lb. (3.6 kg) Electrical Rated frequency 50/60 Hz AC Power supply 100 to 120 VAC, 2.3 A 200 to 240 VAC, 1.0 A Power consumption Operating: 200 W at 100 VAC Standby: 5 W at 100 VAC Environmental Temperature Operating: 41 to 95 °F (5 to 35 °C) Storage: 14 to 140 °F (-10 to 60 °C) Humidity Operating: 20 to 80% RH, non-condensing Storage: 10 to 90% RH, non-condensing Safety United States FCC 47CFR Part 15B Class B (DoC) UL1950 Rev. 3 Canada ICES-003 Class B CSA C22.2 No. 950-95 (cUL) CE Marking Directive 89/336/EEC
Epson POWERLITE HOME 10+ CPD-1790-4R2, 2 Copyright Notice All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Seiko Epson Corporation. The information contained herein is designed only for use with this Epson product. Epson is not responsible for any use of this information as applied to other products. Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third parties for damages, losses, c
Epson POWERLITE HOME 10+ CPD-1790-4R2, 18 3. Press the up or down arrow button on the remote control or the or button on the projector to move through the list of options. When the option you want to change is highlighted, press the Select button. You may see a list of settings, a submenu providing additional options, or a line menu or slider bar similar to the one below: 4. If you see a list of settings, use the arrow buttons on the remote control or the or button on the projector to move to the setting you want, then press the Select button. Enabled settings are indicated by a green light, while
Epson POWERLITE HOME 10+ CPD-1790-4R2, 31 Problem Solving This section explains how to interpret the projector’s status lights, solve problems with the picture and remote control, and contact technical support. What To Do When the Lights Flash The lights on top of the projector indicate the projector’s status and let you know when a problem occurs. If the projector isn’t working correctly, first turn it off, let it cool, and unplug it. Then plug the power cord back in and turn on the projector. If this doesn’t solve the problem, check the status lig
Epson POWERLITE HOME 10+ CPD-1790-4R2, 36 Solving Remote Control Problems The projector doesn’t respond to remote control commands. ■ Make sure you’re within 20 feet of the projector, and within range of the projector’s front or back sensor (approximately 30° left or right, and 15° above or below). ■ You may need to replace the remote control’s battery. See page 26 for details. ■ Dim the room lights and turn off any fluorescent lights. Make sure the projector is not in direct sunlight. ■ Turn off nearby equipment that emits infrared energy, such as a radiant room heater. Where To Get Help Eps
Epson POWERLITE HOME 10+ CPD-1790-4R2, 35 Only part of the picture is displayed, or the picture is distorted. ■ Press the Aspect button to select a different aspect ratio. ■ Use the Position setting in the Setting menu to reposition the image on the screen. See page 22 for details. The picture is trapezoid-shaped. Press the and buttons on the projector to correct the problem. The picture contains static or noise. ■ Make sure your cable is securely connected at both ends. ■ Don’t use an extension cable or a cable longer than 6 feet. ■ If you’re displaying the same image on your computer and projector screen, try turning off your laptop’s LCD d
17 Using the Projector’s Menu System You can use the projector’s on-screen menus to fine-tune the image quality, check lamp usage, and customize projector features: ■ The Image menu controls the look and quality of the picture. It offers several ways to adjust the color and improve the sharpness and clarity of the picture. ■ The Setting menu lets you set the child lock o
5 Important Safety Information Follow these safety instructions when setting up and using the projector: ■ Never look into the projector lens when the lamp is turned on; the bright light can damage your eyes. Never let children look into the lens when it is on. ■ Never open any cover on the projector, except the lamp and filter covers. Dangerous electrical voltages inside the projector can
Epson POWERLITE HOME 10+ CPD-1790-4R2, 26 Cleaning the Projector Case Before you clean the case, turn off the projector and unplug the power cord. ■ To remove dirt or dust, wipe the case with a soft, dry, lint-free cloth. ■ To remove stubborn dirt or stains, moisten a soft cloth with water and a neutral detergent. Then wipe the case. Caution: Never use wax, alcohol, benzene, thinner, or other chemical detergents. These can damage the case. Changing the Remote Control’s Battery You can obtain a replacement CR2025 lithium battery commercially. Warning: Keep ba
34 4. Click Mirror Displays in the lower corner of the screen. One of the monitor icons automatically moves on top of the other. If you’re using a Macintosh laptop with OS 9.x or earlier: 1. From the Apple menu, select Control Panels, then click Monitors and Sound. 2. Click the Arrange icon, and then drag one monitor icon on top of the other. If the Arrange
Epson ELPMBC01 Projection TV Installation and assembly manual
ELPMBC01 |
Epson Stylus Scan 2000 Projection TV Quick start
Stylus Scan 2000 |
Epson EMP-1700 Projection TV Specifications
EMP-1700 |
Epson 4.4 Projection TV Operation manual
4.4 |
Epson Stylus Color 740 Projection TV Operation & user’s manual
Stylus Color 740 |
Epson EasyMP Network Projection Projection TV Operation manual
EasyMP Network Projection |
Epson PowerLite 1915 Projection TV Maintenance manual
PowerLite 1915 |
Epson 730c - PowerLite Projector Projection TV Product support bulletin
730c - PowerLite Projector |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | Sony | RDP-T50iP | Operating instructions | sony/rdp-t50ip-8E5.pdf | 07 May 2023 | 2 | 1.71 Mb |
2 | Alinco | DJ-162 Series | Instruction manual | alinco/dj-162-series-518.pdf | 16 Jul 2022 | 16 | 0.18 Mb |
3 | UAS | Smokeeter SE 24 | Owner's manual | uas/smokeeter-se-24-2N6.pdf | 30 Nov 2023 | 24 | |
4 | Kambrook | KHM10 | Instruction booklet | kambrook/khm10-XH2.pdf | 01 Aug 2022 | 20 | |
5 | Creative | EMU10K1 - Sound Blaster Live! Value | Operation & user’s manual | creative/emu10k1-sound-blaster-live-value-B39.pdf | 09 Apr 2023 | 60 | 2.69 Mb |
6 | Wasp | WPA1000 | Operation & user’s manual | wasp/wpa1000-FNN.pdf | 12 May 2023 | 84 |
Toshiba
51H9357H9365H9323565982Projection TelevisionOWNER'S MANUALOwner’s RecordThe model number and serial number are on the back of your TV. Record these numbers in the spaces below. Refer to these numbers whenever you communicate with your Toshiba dealer about this TV.Model number: Serial number:ISO14001FILENo.A9645TOSHIBAAMERICA …
51H93 - 51" Rear Projection TV(100 pages) |
JVC
For model:AV-61S902PROJECTION TELEVISIONUSER'S GUIDEIMPORTANT NOTE TO THE CUSTOMERIn the space below, enter the serial number for your television (located at the rear of the television cabinet). Staple your sales receipt or invoice to the inside cover of this guide. Keep this user's guide in a convenient place for future reference. Keep the carto …
AV 61S902(68 pages) |
Sony
SERVICE MANUALMODEL COMMANDER DEST. CHASSIS NO. MODEL COMMANDER DEST. CHASSIS NO.MICROFILM∗ Please file according to model size. ...41CHASSIS48 53 61RG-2PROJECTION TVKP-EF41HKRM-871 HK SCC-N71A-AKP-EF41MERM-871 ME SCC-N72A-AKP-EF41MNRM-871 GE SCC-N69A-AKP-EF41SNRM-871 AUS SCC-N73A-AKP-EF48HKRM-871 HK SCC-N71C-AKP-EF48MERM-871 ME SCC-N72C-AKP-EF48MNRM-871 G …
KP-EF41HK(10 pages) |
Philips
3135 035 21401Rear-projectionRear-projectionHDTV MonitorHDTV Monitor55PW938360PW9383Product Highlights• High-definition display—1080i/480p• Philips HD Optics• Auto IntelliSense™Focus• HD DVI and Component Inputs• Active Control™• Eye Fidelity—selectable progressive orinterlaced scan•APAC™(Automatic Phosphor AgingCompensation)Features� …
55PW938399(67 pages) |
Hitachi
DP23/23G/24SAFETY PRECAUTIONS ......................................................................................................2TECHNICAL CAUTIONS ......................................................................................................3SPECIFICATIONS........................................................................................... …
51UWX20B(164 pages) |
Samsung
Register your product at www.samsung.com/global/registerRecord your Model and Serial number here for future reference.▪ Model _______________ ▪ Serial No. _______________Owner’s InstructionsHL-T5656W HL-T6156W HL-T6756WDLP TVBN68-00630D-Eng_1.indd 1 2007-04-09 ソタネト 8:13:51
…
HL-T6756W(144 pages) |
LEGO Toy 71313LEGO Product User Guide: 71313 PDF Assembly instructions manual - 37MCRE 71313, 39 |
Toshiba Network Hardware IPSe8-XToshiba Network Hardware IPSe8-X Hardware manual IPSe8-X, 24 |
Yard-Man Lawn Mower 959 SeriesYard-Man 959 Series User Manual (Owner's manual), @DZWWL6 959 Series, 17 |
ClearOne Telephone MAX IPMAX IP (Telephone ePDF Guide, #H2E2E3) MAX IP, 39 |
HOT Watch Watch ICON1Operation & user’s manual for HOT Watch ICON1 Watch ICON1, 34 |
Ford Automobile 2007 RangerManual: Ford 2007 Ranger (35U7G2, Upd.11th Aug 2023) 2007 Ranger, 7 |
Bayrol Lighting Equipment PoolManager Chlorine#3498E2 PoolManager Chlorine: Bayrol Lighting Equipment Owner Documentation PoolManager Chlorine, 94 |
Freud Saw FTR250PDF User Guide (@6E35A1), Freud FTR250 Saw (27/09/2023) FTR250, 47 |
Maytag Cooktop MGS5752BDBCooktop Use and care manual (Maytag MGS5752BDB) MGS5752BDB, 40 |
Panasonic Air Conditioner CS-RE9JKRAir Conditioner PDF Service manual CS-RE9JKR, 5 |
Mr. Coffee Coffee Maker JWX3PDF Guide (@M2555R), Mr. Coffee JWX3 Coffee Maker (08th Feb 2024) JWX3, 12 |
LG Vacuum Cleaner LUV250CSpecification for LG LUV250C Vacuum Cleaner LUV250C, 2 |