Epson ELPMB27 Installation Manual

Text of Epson ELPMB27 User Guide:

• 2 Safety Instructions Before using the wall mount, make sure you read all of the safety instructions below and then save this manual for later reference. Incomplete or incorrect installation could cause damage to the product or result in personal injury or property damage. For additional information, see the User’s Guide and Safety Instructions included with yo

• Epson ELPMB27, 3 English In order to resist vibration and support the weight of the projector and optional accessories, use M8 nuts and bolts and tighten all screws firmly after installation. Otherwise, the projector or wall mount may fall and cause personal injury or property damage. Epson accepts no responsibility for any damage or injury caused by lack of wall strength or inadequate installation. If you need to loosen any screws while installing, be careful not to drop the projector or the mount. If the projector or the mount falls, it

• 4 Before Use This product is used for mounting the following short throw projectors to a wall: EB-435W/EB-430/EB-425W/EB-420/ PowerLite 435W/PowerLite 430/PowerLite 425W/PowerLite 420. Choosing a Location Determine where you will install the wall mount and prepare the location in advance. Also, make sure there is a gap of 410 to 660 mm (16 to 26 inches) from the top of the image projected onto

• Epson ELPMB27, 5 English Package Contents Use only the supplied bolts to install the wall mount. Do not substitute these bolts with any other types. You need to use commercially available M8 x 50 mm anchors (at least 3) to attach the wall plate to the wall. Gather the tools and parts you need before you begin installation. Hexagonal wrenches (M4 and M8) Installation Manual (this guide) Wall plate cover Wall plate Cable cover Arm cover M4 x 12 mm hexagon socket head cap bolts without washers (x6) M4 x 12 mm hexagon socket head cap bolts with washers (x3) Arm unit Attachment plate Adjustment unit Arm plate Interface cover bracket M8 x 12 mm hexagon socket head cap bolts w

• 6 Specifications Weight Approx. 10 kg (22 lbs.) Maximum load capacity 5.5 kg (12.13 lbs.) Arm length 1510 mm (15.45 inches) (from wall plate attachment point to arm cover point) Vertical slide adjustment range 0 to 134 mm (0 to 5.27 inches) (arm length minimum) 0 to 230 mm (0 to 9.05 inches) (arm length maximum) Vertical tilt adjustment range 0 to - 9.5° Horizon

• Epson ELPMB27, 7 English Screen Size and Projection Distance Refer to the tables on the following pages and install the mount and projector to project images at the appropriate size. The values are only a guide. The recommended projection distance is 70 to 119 cm (27.55 to 46.85 inches). Center of lens Projected image B A C

• Epson ELPMB27, 8 EB-435W/EB-425W/PowerLite 435W/PowerLite 425W Units: cm (inches) Screen size 16:10 WXGA 4:3 XGA 16:9 Widescreen Projection distance (A) Minimum (Wide) Vertical slide adjustment (B) Distance from top of projected image to ceiling (C) Projection distance (A) Minimum (Wide) Vertical slide adjustment (B) Distance from top of projected image to ceiling (C) Projection distance (A) Minimum (Wide) Vertical slide adjustment (B) Distance from top of projected image to ceiling (C) 60" - - - 70 (27.56) 4 (1.57) 43 (16.92) - - - 61" - - - 71 (27.95) 5 (1.97) 44 (17.32) - - - 62" - - - 72 (28.35) 5

• Epson ELPMB27, English 9 * Allow at least 14 cm (5.5 in.) space between the top of the whiteboard and the bottom of the wall plate. 94" 98 (38.58) 6 (2.36) 48 (18.90) 111 (43.70) 7 (2.76) 50 (19.69) 101 (39.76) 13 (5.12) 55 (21.65) 95" 99 (38.98) 6 (2.36) 48 (18.90) 113 (44.49) 7 (2.76) 50 (19.69) 102 (40.16) 13 (5.12) 55 (21.65) 96" 100 (39.37) 6 (2.36) 48 (18.90) 114 (44.88) 7 (2.76) 51 (20.08) 103 (40.55) 13 (5.12) 55 (21.65) 97" 101 (39.76) 7 (2.76) 49 (19.29) 115 (45.28) 7 (2.76) 51 (20.08) 104 (40.94) 13 (5.12) 55 (21.65) 98" 102 (40.16) 7 (2.76) 49 (19.29) 116 (45.67) 7 (2.76) 51 (20.08) 105 (41.34) 13 (5.12) 56 (22.05) 99" 104

• Epson ELPMB27, 10 EB-430/EB-420/PowerLite 430/PowerLite 420 Units: cm (inches) Screen size 16:10 WXGA 4:3 XGA 16:9 Widescreen Projection distance (A) Minimum (Wide) Vertical slide adjustment (B) Distance from top of projected image to ceiling (C) Projection distance (A) Minimum (Wide) Vertical slide adjustment (B) Distance from top of projected image to ceiling (C) Projection distance (A) Minimum (Wide) Vertical slide adjustment (B) Distance from top of projected image to ceiling (C) 58" - - - - - - 70 (27.56) 15 (5.

• Epson ELPMB27, English 11 * Allow at least 20 cm (7.9 in.) space between the top of the whiteboard and the bottom of the wall plate. ** Allow at least 5 cm (2.0 in.) space between the top of the whiteboard and the bottom of the wall plate. 91" 108 (42.52) 16 (6.30) 58 (22.83) 102 (40.16) 2 (0.79) 45 (17.72) 111 (43.70) 22 (8.66) 60 (23.62) 92" 109 (42.91) 16 (6.30) 58 (22.83) 103 (40.55) 2 (0.79) 45 (17.72) 113 (44.49) 22 (8.66) 60 (23.62) 93" 111 (43.70) 16 (6.30) 59 (23.23) 104 (40.94) 2 (0.79) 46 (18.11) 114 (44.88) 23 (9.06) 60 (23.62) 94" 112 (44.09) 17 (6.69) 59 (23.23) 105 (41.34) 2 (0.79) 46 (18.11) 115 (45.28) 23 (9.06) 60 (23.62) 95" 1

• Epson ELPMB27, 12 Assembly and Installation Make sure you follow the instructions below to install the wall mount. Otherwise, the wall mount may fall and result in personal injury or property damage. 1. Installing the wall plate 1) Check the position where you want to install the wall plate, and then mark that position on the wall. As shown in the illustration below, set the horizontal center of the wall plate 8 cm (3.14 inches) to the left of the horizontal center of the whiteboard. Allow at least a 5 cm (1.96 inches) gap between the top of the whiteboard and the bottom of the wall plate. However, if you are using the maximum (tele) screen size, refer to

• Epson ELPMB27, 13 English 2) Position the wall plate over the marks you made in step 1, and then mark the points where the wall plate will be secured as shown in the following illustration. Insert the anchors into at least three points. If you insert four anchors, use the four point As or four point Bs as shown below. 3) Drill holes of the following diameters and depths at the points you marked. 4) Use a device such as a dust pump to clean out concrete dust from the hole. 5) Position the wall plate on the wall an

• Epson ELPMB27, 14 2. Assembling the wall mount 1) Attach the adjustment unit to the arm unit. 2) Secure temporarily using the hexagonal wrenches (M4 and M8) and M4 x 12 mm hexagon socket head cap bolt and M8 x 15 mm hexagon socket head cap bolt. 3) Attach the arm plate using a hexagonal wrench (M8) and four M8 x 12 mm hexagon socket head cap bolts. Arm unit Adjustment unit M8 x 15 mm hexagon socket head cap bolt M4 x 12 mm hexagon socket head cap bolt Arm plate M8 x 12 mm hexagon socket head cap bolts (x4)

• 15 English 3. Routing the cables through the arm unit If you are installing ELPIU03 (sold separately), you also need to route the USB cable supplied with ELPIU03 through the arm unit. 4. Attaching the wall mount to the wall plate 1) Attach the hook on the arm plate to the bar on the wall plate. Be careful not to pinch cables between the arm plate and the wall plate. 2) Se

• Epson ELPMB27, 16 5. Attaching the attachment plate to the projector 1) Place the projector upside down. 2) Attach the attachment plate to the projector using the hexagonal wrench (M4) and five M4 x 12 mm bolts with washers/ spring washers. 6. Attaching the projector to the adjustment unit 1) Slide the attachment plate onto the adjustment unit as shown below. 2) Secure the adjustment unit temporarily at the points marked using two M4 x 12 mm bolts as shown below. q Tighten the screws firmly. M4 x 12 mm hexagon socket head cap bolts (x5) with washers/spring washers Attachment plate

• Epson ELPMB27, 17 English 7. Extending the arm, adjusting the length, and securing temporarily 1) Loosen the screw on the arm.( ) 2) Adjust the length of the arm using the measure on the bottom to match the projection distance recommended in "Screen Size and Projection Distance" on page 7.( ) 3) After adjusting the length, secure the arm position temporarily by tightening the screw on top.( ) 8. Connecting the cables Connect the power cord and other cables to the projector. If you are installing ELPIU03, see the Quick Setup Guide included with

• Epson ELPMB27, 18 10. Turning on the projector and checking the screen 1) Plug in the projector. 2) Turn on the projector. 3) Loosen the screws on the adjustment unit (A, B, C, and D) as shown below to adjust the screen position. 4) Adjust the vertical slide (arm angle) using screw (E) on the bottom of the arm plate. The arm rises when you tighten the screw, and lowers when you loosen it. 5) Firmly tighten the screws on the arm unit and adjustment unit using the hexagonal wrenches (M4 and M8). Adjustment unit Arm plate A: Vertical tilt adjustment: 0 to -9.5° B: Horizontal roll adjus

• Epson ELPMB27, 19 English 11. Attaching the interface cover bracket Attach the interface cover bracket using the hexagonal wrench (M4) and two M4 x 12 mm bolts with washers. 12. Attaching the cable cover Take up the cable slack, and then secure the cable cover with the screws as shown below. Interface cover bracket M4 x 12 mm hexagon socket head cap bolts (x2) with washers Cable cover

• Epson ELPMB27, 20 13. Attaching the wall plate cover Secure the wall plate cover with a hexagonal wrench (M4) and three M4 x 12 mm hexagon socket head cap bolts. Installation, removal, and servicing of the projector should only be performed by a qualified technician. See the User’s Guide included with your projector for information about maintenance and repairs. Wall plate cover Wall plate cover M4 x 12 mm hexagon socket head cap bolts (x3) ❏ Never loosen the bolts and nuts after installation. Confirm on a regular basis that the screws have not become loose. If you find any l

More Instructions:

Epson ELPMB27 Product overview 15-01-2023 2

DOWNLOAD

Related Products and Documents (Projector Accessories):

Comparable Devices:

Similar Resources:

• Premier Mounts Universal Projector Mount PBL-UMS (16 pages) I N S T A L L A T I O N M A N U A L VISIT US AT WWW.MOUNTS.COM 3130 E. Miraloma Ave. Anaheim, CA 92806 Phone: 800 368-9700 Fax: 800 832-4888 PREMIER ©2004/ R …

• Delta Electronics NovoConnect B360 (71 pages) Copyright © 2013 DELTA Electronics, Inc. All rights reserved. Page 1 User Manual Version 0.99 NovoConnect™ B360 Wireless Presentation & Collaboration System …

• NEC WT615 (2 pages) LCDs • Projectors • Plasmas • LCDs • Projectors • Plasmas • LCDs • ProjectorsNEC WT615Innovative projector with extremely short projection distance and integrated whiteboard function – for direct notes on the projection surface.Native Resolution: 1024 x 768 (XGA)•Brightness: 3500 Lumens (2000 ANSI Lumens)•Contrast Ratio: 3500:1•LAN and …

• Navitar 606MCZ087 (1 pages) Installation of Navitar/NuView Series 606 lens on Epson PowerLite 7800p, 7850p, 7900 & 7950 Projectors TOOLS REQUIRED: PHILLIPS HEAD SCREWDRIVER, 9/64” ALLEN WRENCH Disassembly: 1. Disconnect the unit from the power source and place projector with the bottom facing up. Remove one (1) Phillips head screw holding the lens cover of the projector in p …

• Sanyo MT-EDU101 (2 pages) FEATURES SPECIFICATIONSFEATURES SPECIFICATIONS• Includes two, 25-watt two-way speakers with 5" woofer and directional tweeters • Integrated 50-watt power amp resides within wall mount wall plate • Multiple inputs, including separate line-level mic input• Dynamic sound range easily reaches back …

• TOOQ PJ4017WTN-B (2 pages) 7626k g(57lbs )R A T E D820-1200mm3 6 0 °20° -20° 20° -20° ©2017 by TOOQ technology, S.L. Released in 2019/06.AII Rights Reserved.tooq.com• Un équipement de sécurité et des outils appropriés doivent être utilisés. Ce produit ne doit être installé que par des professionnels.• Ce produit contient de petits objets pouvant présenter un risque …

Comments, Questions and Opinions: