Manualios.com

Epson MediaLink Controller MLC 104 IP Plus Setup Manual

  • MediaLink Controller MLC 104 IP Plus Switch
  • mabVyVgc4lxhU
  • Setup Manual
  • PDF / Adobe Acrobat Reader
  • 26

Epson MediaLink Controller MLC 104 IP Plus Manual Online:

3.15, 1832 votes
Epson MediaLink Controller MLC 104 IP Plus User Manual
Epson MediaLink Controller MLC 104 IP Plus User Guide
Epson MediaLink Controller MLC 104 IP Plus Online Manual

Text of Epson MediaLink Controller MLC 104 IP Plus User Guide:

  • Epson MediaLink Controller MLC 104 IP Plus, MLC 104 IP Plus • Hardware Setup Hardware Setup, cont’d 2-8 MLC 104 IP Plus • Hardware Setup 2-9 Left Side/Top Panel Features and Connections RESET MLC 104 IP Plus Left Side 1 a Reset button and LED — Pressing this recessed button causes various IP functions and Ethernet connection settings to be reset to their factory defaults. For reset modes, refer to chapter 2 in the MLC 104 IP Plus User's Manual. b IR signal sensor — This sensor allows for IR learning. It receives and "learns" commands from other devices' infrared remote controls so an IR driver can be created. Refer to the IR Learner Help File from

  • MLC 104 IP Plus • Hardware Setup Hardware Setup MLC 104 IP Plus • Hardware Setup 2-32-2 This chapter describes right, left, and front panel features; basic front panel operation; and how to connect cables to the MLC 104 IP Plus controller. Right Side Panel Features and Connections 2 3 GRO U N D 1 IR I N GRO U N D IR O U T CM SCP GRO U N D GRO U N D Tx Rx DISPLAY

  • Epson MediaLink Controller MLC 104 IP Plus, MLC 104 IP Plus • Software Setup Software Setup, cont’d 3-24 To begin the upload, do the following: 1. Click Begin. The Upload Manager monitors the progress of the upload. 2. When the upload is finished, click Close. The configuration should now be successfully uploaded to the appropriate product(s). Accessing GlobalViewer ® After uploading a configuration file to an MLC 104 IP Plus controller, there are three ways to access the GlobalViewer Web page: From the Upload Manager window, click the Test GV System button. Right-click the MLC 104 IP Plus controller icon in the IP Link tree and select Open GlobalViewer ® Webpage. Open an Internet b

  • MLC 104 IP Plus • Software Setup Software Setup, cont’d 3-16 MLC 104 IP Plus • Software Setup 3-17 Control module main window 4. Select the Address #1 tab. The Address 1 IRCM-DV+ [DVD] window appears. 5. In the upper left corner drop-down menu (under DVD & VCR Control), select Input 2, as illustrated below. This assigns the input button (Inp

  • MLC 104 IP Plus • Hardware Setup Hardware Setup MLC 104 IP Plus 2-12 3 Chapter Three MLC 104 IP Plus Software Setup Step 1: Download Device Drivers Step 2: Create a New Project Step 3: Add an MLC 104 IP Plus Controller and Define its Location Step 4: Define E-mail Settings Step 5: Add a Serial and an IR Device Step 6: Configure the Front Panel Buttons Step 7: Configure the Co

  • Epson MediaLink Controller MLC 104 IP Plus, Precautions This symbol is intended to alert the user of important operating and maintenance (servicing) instructions in the literature provided with the equipment. This symbol is intended to alert the user of the presence of uninsulated dangerous voltage within the product’s enclosure that may present a risk of electric shock. Caution Read Instructions • Read and understand all safety and operating instructions before using the equipment. Retain Instructions • The safety instructions should be kept for future reference. Follow Warnings • Follow all wa

  • Epson MediaLink Controller MLC 104 IP Plus, MLC 104 IP Plus • Hardware Setup Hardware Setup, cont’d 2-4 MLC 104 IP Plus • Hardware Setup 2-5 MLC 104 IP Plus Right Side Panel COMM LINK A B C D E +V OUT GROUND CM IR IN SCP E C B A SCP communication (IR) Ground ( ) IRCM, ACM, RCM, CM +12 VDC C B A Maximum = 2 SCPs Per System Maximum = 4 Control Modules (4 module addresses) Ground ( ) +12 VDC Ground ( ) & Drain Wire E C B A SCP Communication Control Module Communication +12 VDC = White = Black & Drain Wire = Violet = Red IRCM, ACM, RCM, CM DVD & VCR CONTROL PLAY NEXT/FWD PAUSE STOP TUNER Tx PREV/REW ENTER TITLE MENU TV/VCR DVD VCR SCP 104 IRCM-DV+ CONFIG DISPLAY VOLUME SCP 104

  • Epson MediaLink Controller MLC 104 IP Plus, MLC 104 IP Plus • Hardware Setup Hardware Setup, cont’d 2-6 MLC 104 IP Plus • Hardware Setup 2-7 Both digital input and output modes of the digital I/O ports have the ability to turn on an internal pull-up resistor to + 5 VDC (equivalent to SW2 on the previous illustration). N Refer to the MLC 104 IP Plus User's Manual for further details on configuring this port. d MLS RS-232 connector — This port can control an optional Extron switcher or other RS-232 controllable device. If you connect an optional switcher (such as an Extron MLS Series switcher) to the MLC, you must connect a ground wire between th

  • Epson MediaLink Controller MLC 104 IP Plus, MLC 104 IP Plus • Software Setup Software Setup, cont’d 3-4 MLC 104 IP Plus • Software Setup 3-5 Step 2: Create a New Project 1. If the GC 2 Start Options dialog is displayed, select the "Create a New Project" option and click the OK button. The Project Settings dialog box appears, as shown below. N You can also access the Project Settings dialog box via the Edit menu. Project Settings dialog box 2. If passwords have been set on the MLC, enter the administrator and user passwords. Ensure that both passwords are repeated in the Verify fields. N If a password has been set on the MLC 104 IP Plus controller but none is entered here, you will be unable to uplo

  • Epson MediaLink Controller MLC 104 IP Plus, MLC 104 IP Plus • Introduction Introduction, cont’d 1-6 MLC 104 IP Plus 2 Chapter Two MLC 104 IP Plus Hardware Setup Right Side Panel Features and Connections Left Side/Top Panel Features and Connections Front Panel Features and Basic Operation

  • Epson MediaLink Controller MLC 104 IP Plus, MLC 104 IP Plus • Introduction Introduction, cont’d 1-4 MLC 104 IP Plus • Introduction 1-5 Global Configurator provides the following features for the MLC 104 IP Plus: Offline configuration — Using Global Configurator, you can configure your MLC 104 IP Plus Medialink controller without having the device on hand, eliminating the need to connect your MLC before starting the configuration. GlobalViewer Web pages — GlobalViewer Web pages (HTML, XML, and JavaScript) allow you to control and manage devices such as VCRs, DVDs, and displays connected to an MLC 104 IP Plus. These pages are generated when you build and upload your project files in GC.

  • i MLC 104 IP Plus • Table of Contents Table of Contents Chapter One • Introduction ................................................... 1-1 About this Manual .................................................................... 1-2 About the MLC 104 IP Plus Medialink ™ Controllers ........ 1-2 About Global Configurator ............................................

  • Epson MediaLink Controller MLC 104 IP Plus, 安全须知 • 中文 这个符号提示用户该设备用户手册中 有重要的操作和维护说明。 这个符号警告用户该设备机壳内有暴 露的危险电压,有触电危险。 注意 阅读说明书 • 用 户 使 用 该 设 备 前 必 须 阅 读 并 理 解 所 有 安 全 和 使 用 说 明 。 保存说明书 • 用户应保存安全说明书以备将来使 用。 遵守警告 • 用户应遵守产品和用户指南上的所有安 全和操作说明。 避免追加 • 不要使用该产品厂商没有推荐

  • Epson MediaLink Controller MLC 104 IP Plus, © 2006 Extron Electronics. All rights reserved. Extron Electronics, USA 1230 South Lewis Street Anaheim, CA 92805 USA 714.491.1500 Fax 714.491.1517 Extron Electronics, Europe Beeldschermweg 6C 3821 AH Amersfoort The Netherlands +31.33.453.4040 Fax +31.33.453.4050 Extron Electronics, Asia 135 Joo Seng Road, #04-01 PM Industrial Building Singapore 368363 +65.6383.4400 Fax +65.6383.4664 Extron Electronics, Japan Kyodo Building 16 Ichibancho Chiyoda-ku, Tokyo 102-0082 Japan +81.3.3511.7655 Fax +81.3.3511.7656 www.extron.com Setup Guide 68-1289-01 Rev. A 08 06 MLC 104 IP Plus MediaLink TM Controller

  • Epson MediaLink Controller MLC 104 IP Plus, MLC 104 IP Plus • Software Setup Software Setup, cont’d 3-6 MLC 104 IP Plus • Software Setup 3-7 Add Device dialog box (Advanced) 5. Select the Auto Configure IP Address check box. The MAC Address text box becomes active and the first three octets of the MAC address appear. 6. Locate the MAC address on the rear of the Extron IP product or obtain it from your network administrator. 7. Enter the remainder of the MAC address in the MAC Address text box (the first three octets should be filled in). 8. Click the Set button. This assigns the new IP address to the IP device. 9. Click the New Location button in the upper right c

  • Epson MediaLink Controller MLC 104 IP Plus, MLC 104 IP Plus • Software Setup Software Setup, cont’d 3-18 MLC 104 IP Plus • Software Setup 3-19 Step 8: Create a Display Shutdown Schedule Global Configurator’s (GC) scheduling feature enables you to schedule actions and events for a selected device. Scheduling is often useful for setting a projector or other device to shut down or turn on at a predetermined time (e.g., in a school, all projectors can be set to power off at 5:00 P.M.). To schedule a display shutdown: 1. Click on the Schedule tab in the Global Configurator window. 2. Click the Add Schedule button below the Scheduled Actions window. The Scheduled Actions Wizard dialog box appears, as shown below.

  • Epson MediaLink Controller MLC 104 IP Plus, MLC 104 IP Plus • Software Setup Software Setup MLC 104 IP Plus • Software Setup 3-2 3-3 This chapter provides the steps for setting up your MLC 104 IP Plus controller using the Global Configurator (GC) software. By means of example, you will learn how to • Add drivers that allow control of A/V devices. • Configure the controller's power buttons, and input selection buttons to control a video projector. • Configure an IRCM-DV+ control module to control the functions of a DVD/VCR player. • Schedule a projector shutdown, create a lamp hour warning alert, and create a projector disconnection e-mail alert. Each of the following steps of co

  • Epson MediaLink Controller MLC 104 IP Plus, MLC 104 IP Plus • Hardware Setup Hardware Setup, cont’d 2-10 MLC 104 IP Plus • Hardware Setup 2-11 Front Panel Features and Basic Operation There are several features that must be set up prior to using the MLC. Refer to chapter 4 in the MLC 104 IP Plus User's Manual for details. CONFIG DISPLAY VOLUME MLC 104 IP PLUS ON VCR DVD PC OFF 1 2 3 4 MLC 104 IP Plus Front Panel 4 2 1 3 Buttons The MLC 104 IP Plus controller has backlit buttons. The button caps are removable so the button labels can be changed. For instructions on how to

  • Epson MediaLink Controller MLC 104 IP Plus, MLC 104 IP Plus • Software Setup Software Setup, cont’d 3-8 MLC 104 IP Plus • Software Setup 3-9 4. Complete each of the fields with your mail server IP address, mail server domain, and, if necessary, your user name and password. 5. Click the OK button. 6. Go back to the Settings menu to complete the entries for your subnet mask and gateway settings. Setting up e-mail notifications The Email Manager provides preset messages for some of the most common actions performed in GC. To set up an e-mail notification for a specified action, do the following: 1. From the Global Configurator Edit menu, choose Email M

  • Epson MediaLink Controller MLC 104 IP Plus, MLC 104 IP Plus • Software Setup Software Setup, cont’d 3-12 MLC 104 IP Plus • Software Setup 3-13 Adding an IR driver To add an IR driver to a port: 1. From the IP Link tab (left pane), select the IR port labeled Port A beneath the MLC 104 IP Plus tree. Add IR driver window 2. Use the drop-down menus under IR Driver Selection to select the device type (choose DVD/VCR), and manufacturer (choose Hitachi). In the Available Drivers field, choose Hitachi DV-PF7E. N If you are unab

  • Epson MediaLink Controller MLC 104 IP Plus, MLC 104 IP Plus • Software Setup Software Setup, cont’d 3-14 MLC 104 IP Plus • Software Setup 3-15 4. Drag the On icon to the right-side window field labeled Release. This sets the command to activate on the release of the button. N Failure to configure the On or Off buttons on Release may cause problems with the PIN Mode feature. Refer to the MLC 104 IP Plus User's Manual for details. Notice that the Epson PowerLite 7700p projector now appears under the Release field, and the front panel On button is marked with a red triangle. This indicates that the On button is now configured. 5. To configure the Off button, repeat

  • Epson MediaLink Controller MLC 104 IP Plus, MLC 104 IP Plus • Software Setup Software Setup, cont’d 3-22 MLC 104 IP Plus • Software Setup 3-23 Step 10: Create a Display Disconnection E-mail To set a display disconnected e-mail alert, do the following: 1. Click the Monitor tab in the Global Configurator window. 2. Click the Add Monitor button below the Monitored Conditions window. The Monitored Conditions Wizard window appears. 3. Enter a name (Disconnected) in the Enter Monitored Condition Name field area. The label now appears in the left pane. 4. Click Next to specify a condition. 5. Select the desired equipment (for our purposes

  • Epson MediaLink Controller MLC 104 IP Plus, MLC 104 IP Plus • Software Setup Software Setup, cont’d 3-20 MLC 104 IP Plus • Software Setup 3-21 Step 9: Create a Display Lamp Hour Warning E-mail Global Configurator’s monitoring feature enables you to configure an MLC 104 IP Plus controller to monitor many parameters of the connected display devices. For example, a monitor alert can warn the school administrator if a display lamp hour limit is close to expiration or if a display is inexplicably disconnected from the MLC 104 IP Plus controller. To set a display lamp hour warning e-mail, do the following: 1. Click the Monitor tab in the Global Configurator window. 2. Click the Add Monitor button

  • Epson MediaLink Controller MLC 104 IP Plus, MLC 104 IP Plus • Introduction Introduction MLC 104 IP Plus • Introduction 1-2 1-3 A typical application for an MLC 104 IP Plus Medialink Controller About Global Configurator The Extron Global Configurator (GC) software is an application that allows non-programmers to configure a wide range of Extron IP Link ® -enabled products, and create entire GlobalViewer ® systems. It provides an integrated environment for defining A/V control and system monitoring functionality from an easy-to-use graphical user interface. It allows you t

Related Products and Documents (Switch):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Tripp Lite 93-1990 (200108029) Product manual tripp-lite/93-1990-200108029-UA6.pdf 23 Jun 2022 5 0.1 Mb
2 Bolide Technology BC2002-AT88 Operation & user’s manual bolide-technology/bc2002-at88-22O.pdf 04 Aug 2022 38 0.66 Mb
3 Craftsman 917.272481 Owner's manual craftsman/917-272481-O13.pdf 05 Dec 2022 64 2.54 Mb
4 Grundfos CRIE Installation and operating instrictions grundfos/crie-QPD.pdf 02 Aug 2023 38
5 Naxa NT-2207 Instruction manual naxa/nt-2207-9SV.pdf 13 Sep 2022 16
6 KYLAND Technology SICOM3171 Series Quick installation manual kyland-technology/sicom3171-series-1X2.pdf 20 Mar 2024 11

Similar Resources:

  • Air Live

    Live-GSH5T

    (25 pages)
    User’s Manual Live-GSH5T v.1.0 Aug., 2005 Copyright © OvisLink Corp. All Gigabit SOHO Switch 5 × 10/100/1000Base-T NWay Auto-MDI/MDIX With Broadcast Storm Control Live-GSH5T …
  • Makel

    MSA0405-CF

    (2 pages)
    1 6T 7301.cRFTP230V~Bus30 Vs 5AAkkor lambalar 230 V 800 WIncandescent lampsHalojen lambalar 230 V 800 WHalogen lamps12V DC 24V DC800 W transformer12V DC 24V DC800 WElectr transformer 800 WFluorescent tubes non compensated 230 V W 63 x 21Fluorescent tubes for electr ballast (mono or duo) 230 VW 32 x 6Compact rescentMSA0810-B30 …
  • Eaton

    ATC-300

    (9 pages)
    1 Ethernet Remote Annunciator Controller (RAC) Instruction Sheet for Automatic Transfer Switches (4 x ATS) Revision: 01 IB01602082E 1.1 Ethernet Remote Annunciator Controller (RAC) using the up to 4 ATC-300+ connected via RS-485 to TCP/IP gateway The 7” RAC is a color touch-screen display with easy-to-use functions that provide a powerful interface w …
  • Alps Electric

    SLLQ Series

    (4 pages)
    Multi ControlDevicesVariableResistor TypeSwitchType307DetectorPushSlideRotaryEncodersPowerDual-in-linePackage TypeTACT SwitchTMCustom-ProductsRating(max.)/(min.)(Resistive load)Output voltage Operating forceOperating lifePush portionPush portionLever portionLever portionTravel(Push operation)Typical SpecificationsItems10mA 5V DC/50BA 3V DC1V …
  • Nexans

    iSwitch 740

    (35 pages)
    - 1 - Industrial Ethernet iSwitch 74x Description and Operating Instructions KD-0655E06 Fig. 1: iSwitch 742 SFP – front view Order numbers 7x TP 6x TP / 1x FO 5x TP / 2x FO iSwitch 740 iSwitch 741 GI(SC)* iSwitch 742 GI(SC)* fiber-optic GI(SC) iSwitch 740 24V iSwitch 741 24 V GI(SC) iSwitch 742 24V GI(SC) iSwitch 740 48V iSwitch 7 …
  • Tripp Lite

    PDUMV30HVNET

    (4 pages)
    Tripp Lite1111 West 35th StreetChicago, IL 60609 USATelephone: +(773) 869 1234E-mail: [email protected] #: PDUMV30HVNETSingle-Phase Switched PDU, 30A 208/240V, 0U Vertical Rackmount, C13 & C19 outlets, NEMA L6-30P inputplug HighlightsSwitched 30A 208/240V PDU; 70in / 178cm 0u Vertical RackmountReports voltage, frequency & loading informat …

Comments, Questions and Opinions: