Manualios.com

Texas Instruments TVP5146EVM Operation & User’s Manual

Texas Instruments TVP5146EVM Manual Online:

3.5, 2360 votes
Texas Instruments TVP5146EVM User Manual
Texas Instruments TVP5146EVM User Guide
Texas Instruments TVP5146EVM Online Manual

Text of Texas Instruments TVP5146EVM User Guide:

  • SLEU063 TVP5160EVM User’s Guide 17 8.3 I 2 C System Test The I 2 C system test of selected registers runs immediately after closing the WinVCC4 Configuration dialog box with OK (unless the I 2 C system test program options button was disabled). If the I 2 C system test passes, then only a PASS message will appear. If the test failed, then a dialog box like Fi

  • Texas Instruments TVP5146EVM, 1 2 3 4 5 6 A B C D 654321 D C B A Title Number RevisionSize C Date: 16-Feb-2005 Sheet of File: C:\Userdata\EVM Design Files\MODULARIZED_EVMS\ADV7311EVM_MODULE_REV1.0\ADV7311EVM_MODULE_REV1.0.DdbDrawn By: ADV7311 MODULE REV 1.0 R/Pr SV B/Pb G/Y CVBS REV 1.0 ENCODER EVM - BLOCK DIAGRAM SCL SDA I2C I2C RESET CONN_RESET Power Power SDA SCL /HSYNC /VSYNC /BLANK CLKIN RTC UV[9..0] Y[9..0] Testpoints Testpoints CLKIN /VSYNC /HSYNC SDA SCL CONN_RESET RTC /BLANK Y[9..0] UV[9..0] Connector Connector /HSYNC /VSYNC /BLANK CLKIN RTC /RESET C[9..0] Y[9..0] SCL SDA ADV7311 ADV7311 DVI Tx DVI Tx ADV7311 Board Revision 1.0 Feb 2005

  • Texas Instruments TVP5146EVM, SLEU063 TVP5160EVM User’s Guide 13 5. At the Real-Time Polling window, ensure that VIDEO-STANDARD AUTO_SWITCH POLLING is enabled and click OK. Figure 4. WinVCC4 – Real Time Polling Screen 6. Load the provided TVP5160EVM.CMD file into WinVCC4 by clicking on Tools -> System Initialization -> Browse. The CMD should be available by default as seen below. Figure 5. WinVCC4 – Main Screen 7. Click the “TVP5160 (SD) + ADV7311” dataset in the window and then click the Program Dataset button to initialize the TVP5160EVM. Figure 6. WinVCC4 – System Ini

  • Texas Instruments TVP5146EVM, IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware product

  • Texas Instruments TVP5146EVM, SLEU063 TVP5160EVM User’s Guide 33 Table 10. I 2 C Troubleshooting Symptom Cause Solution I 2 C slave address is wrong. Close and restart WinVCC4. Choose the alternate slave address in the WinVCC4 Configuration dialog. Parallel cable is not connected from PC parallel port to the EVM DB25 connector. Connect cable. EVM is not powered on. The power supply must be plugged into a 100-V to 240-V/ 47-Hz to 63-Hz power source and the cord must be plugged into the power connector on the EVM. Wrong type of

  • SLEU063 12 TVP5160EVM User’s Guide 7 WinVCC4 Quick Start The following describes the steps to take within WinVCC4 in order to get video out of the TVP5160EVM. 1. Once WinVCC4 is executed, the WinVCC4 Configuration screen appears. This dialog box is used to configure the I 2 C bus. Next to VID_DEC, select the TVP5160 and ensure the I 2 C address is set to 0xB8. This shoul

  • Texas Instruments TVP5146EVM, SLEU063 TVP5160EVM User’s Guide 29 8.5.3 Property Sheets The Property Sheets represent the register data in a user-friendly format. The data is organized by function, with each function having its own page and being selectable via tabs at the top. To open this, click on Edit Property Sheets in the Edit menu and select the device type to edit. When the property sheet function is started or whenever you tab to a different page, all readable registers in the device are read from hardware to initialize the dialog pages. Value

  • Texas Instruments TVP5146EVM, TVP5160EVM User’s Guide SLEU063 – March 2005 1 TVP5160EVM User’s Guide Digital Video Department Contents 1 Functional Description......................................................................................................................3 1.1 Description Overview ...................................................................................................................3 2 Board Level Description...................................................................................................................4 2.1 Analog In

  • Texas Instruments TVP5146EVM, 1 2 3 4 5 6 A B C D 654321 D C B A Title Number RevisionSize B Date: 16-Feb-2005 Sheet of File: C:\Userdata\EVM Design Files\MODULARIZED_EVMS\TVP5160EVM\TVP5160EVM_MODULE_REV2.0\TVP5160EVM_MODULE_REV 2.0.ddb Drawn By: TVP5160EVM - SDRAM 50-PIN TSOP II DQ[15..0] /CAS /RAS DQM AQ[11..0] CLK /WE C51 0.1uF C52 0.1uF C53 0.1uF C54 0.1uF C55 0.1uF VDD 1 DQ0 2 DQ1 3 VSSQ 4 DQ2 5 DQ3 6 VDDQ 7 DQ4 8 DQ5 9 VSSQ 10 DQ6 11 DQ7 12 VDDQ 13 DQML 14 WE_ 15 CAS_ 16 RAS_ 17 CS_ 18 BA 19 A10 20 A0 21 A1 22 A2 23 A3 24 VDD 25 VSS 26 A4 27 A5 28 A6 29 A7 30

  • SLEU063 TVP5160EVM User’s Guide 21 8.5.1.1 Adding a Custom Data Set After you program the EVM via the System Initialization tool using the factory-supplied command file, and by using the Property Sheets tool, you can customize the device register settings to suit your needs. To save your custom settings: 1. Reopen the System Initialization dialog via the Tools menu. 2. Click the

  • SLEU063 TVP5160EVM User’s Guide 23 7. The write to register command is written as follows: WR_REG, <DeviceFamily>, <Number of data bytes (N)>, <subaddress>, <Data1>,…, <DataN> or WR_REG, <Literal slave address>, <Number of data bytes (N)>, <subaddress>, <Data1>,…, <DataN> The valid device family m

  • Texas Instruments TVP5146EVM, SLEU063 10 TVP5160EVM User’s Guide 5 Hardware Setup The following describes how to set up the hardware for the TVP5160EVM. 1. Connect the TVP5160EVM boards together using the 120-pin board connector on each board. 2. Connect a CVBS input to the TVP5160 board and a component cable to the YPbPr outputs of the ADV7311 board. NOTE: For evaluation it is recommended that the YPbPr component video outputs be used in order to bypass the internal video decoder of the TV or video display. 3. Connect the parallel port cable from the TVP5160EVM to the PC. NOTE: There are footprints for a dc jack and a DB25 connector on the ADV

  • Texas Instruments TVP5146EVM, SLEU063 18 TVP5160EVM User’s Guide If the WinVCC4 autoswitch polling function is enabled, then the detected video standard status from the TVP5160 decoder is polled until a change in the input video standard (or in the TVP5160 sampling mode) is detected. When a change is detected, the video encoder is reprogrammed as needed for the detected standard. Using this feature, the video source can change its video standard and the system will display using the new standard without user intervention. To enable autoswitch polli

  • Texas Instruments TVP5146EVM, SLEU063 34 TVP5160EVM User’s Guide Figure 18. I 2 C System Failure Dialog Box 9.2 Corrective Action Dialogs After closing the I 2 C system test report dialog box, the dialog in Figure 19 appears. Figure 19. Corrective Action Dialog Box 1. If the cable is NOT connected from the PC parallel port to the TVP5160EVM or if the EVM power is not on: a. Click NO. b. The dialog shown in Figure 20 appears instructing you to correct the problem.

  • Texas Instruments TVP5146EVM, SLEU063 26 TVP5160EVM User’s Guide 8.5.2.2 Encoder Module Editor The encoder module editor, as shown in Figure 14, allows the display and editing of the video encoder registers. This editor works like the Register Map Editor. To open this, click on Edit Register Map in the Edit menu and click on Encoder Module. Figure 14. Encoder Module Editor

  • Texas Instruments TVP5146EVM, 1 2 3 4 5 6 A B C D 654321 D C B A Title Number RevisionSize C Date: 16-Feb-2005 Sheet of File: C:\Userdata\EVM Design Files\MODULARIZED_EVMS\ADV7311EVM_MODULE_REV1.0\ADV7311EVM_MODULE_REV1.0.DdbDrawn By: FFOE/DIG_V 1 FFRE/DIG_H 2 FFRSTWIN/~SCLK 3 FFWE/DVALID 4 FFIE/CCVALID 5 VGAV/SYNC_T 6 FSY/HC/HSYA/~BLNK 7 FFRSTW/CBFLAG 8 FPDAT/VSYA/M2 9 CLK5/M1 10 GND 11 PHI_D0 12 PHI_D1 13 PHI_D2 14 PHI_D3 15 PHI_D4 16 PHI_D5 17 PHI_D6 18 PHI_D7 19 PHI_A0 20 PHI_A1 21 PHI_CS 22 PHI_DS/RD 23 SDA/PHI_RWW 24 SCL/PHI_ACK 25 GND 26 GND 27 GND 28 5V 29 5V 30 D_VS 31 D_HS 32 D_PREF 33 D_RDY 34 D_SCLK 35 VACTIVE 36 SOGOUT 37 ITRDY 38 GND 39 GPCL 40 INTREQ 41 GPIO0 42 GPIO1 43 GPIO2 44

  • Texas Instruments TVP5146EVM, SLEU063 TVP5160EVM User’s Guide 35 c. Correct the problem. d. Click OK to continue. The real-time polling dialog should appear. See Section 3.2.3. Figure 20. Corrective Action Required 2. If the cable is connected from the PC parallel port to the TVP5160EVM AND the EVM power is on: a. Click Yes. b. The dialog shown in Figure 21 appears. This dialog appears if the PC parallel port mode setting may need to be changed. NOTE: Only run the PC BIOS setup program if the I 2 C communication problem cannot be resolved in another way. (Correct slave address settings, reset or power cycle the EVM and/or check that the device type

  • Texas Instruments TVP5146EVM, SLEU063 TVP5160EVM User’s Guide 3 1 Functional Description The TVP5160EVM refers to both the TVP5160 board and the ADV7311 board when they are connected together. Both boards share a common interface via a 120-pin connector. This interface provides all data, clocks, I 2 C communication, and 5-V power to each board. The ADV7311 is a professional grade, 12-bit, 216-MHz, video encoder. This device minimizes potential artifacts caused by the re-encode process. When evaluating the TVP5160 decoder, it is highly recommended that the YPbPr component video outputs of the ADV7311 be used. This will ensure the video decoder within the display monitor will not be u

  • Texas Instruments TVP5146EVM, SLEU063 TVP5160EVM User’s Guide 9 4 Required Hardware and Equipment The following lists the required hardware and equipment necessary to use the TVP5160EVM: - TVP5160EVM (provided) - Universal 5-V power supply (provided) - Parallel cable (provided) - Windows-based PC - 1 composite RCA video cable - 1 YPbPr component RCA video cable - Video source (pattern generator, DVD player, etc) - TV or display monitor that supports YPbPr component video inputs

  • Texas Instruments TVP5146EVM, SLEU063 36 TVP5160EVM User’s Guide 1. Restart the PC. 2. During the boot process, enter the BIOS setup program by pressing the required key (usually the initial text screen tells you which key to press). 3. Find the place where the parallel port settings are made. 4. Set the parallel port LPT1 at address 378h to ECP mode or bidirectional mode (sometimes called PS/2 mode or byte mode). If one of these two modes is already selected, change to the opposite mode. 5. Exit and save changes. 9.2.2 General I 2 C Error Report The error report shown in Figure 22 appears when an I 2 C error occurs at any time

  • Texas Instruments TVP5146EVM, SLEU063 TVP5160EVM User’s Guide 25 Table 5. Register Map Editor Controls Control Definition Register Window Scrolling text box that displays the address and data for the I 2 C registers that are defined for the device. Address Edit Box This contains the I 2 C subaddress that will be accessed using the Write and Read buttons. Clicking on a row selects an address, which then appears in the address edit box. NOTE: After clicking on a row, the Data Edit box contains the data that was in the register window. The device has not yet been read. The address up/down arrows are used to j

  • Texas Instruments TVP5146EVM, SLEU063 TVP5160EVM User’s Guide 15 8 WinVCC4 in Depth The following describes how to use WinVCC4 in depth. It discusses various features and screens which the user may encounter while evaluating the TVP5160EVM. 8.1 Starting WinVCC4 The Port95NT parallel port driver must be installed before using WinVCC4. WinVCC4 may be started by clicking on Start->All Programs->TVP5160EVM Software->WinVCC4. If the dialog shown in the figure below is displayed, it means one of two things: 1. WinVCC4 did not run to comp

Related Products and Documents (TV Receiver):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Chamberlain 3245M Owner's manual chamberlain/3245m-7SP.pdf 03 Oct 2023 36 2.36 Mb
2 JVC CU-VS100U Easy start manual jvc/cu-vs100u-XP4.pdf 18 Dec 2023 2
3 Grandstream Networks GXV-3140 Quick start manual grandstream-networks/gxv-3140-8I4.pdf 24 Sep 2022 17 6.22 Mb
4 West Bend 6 quart Instruction manual west-bend/6-quart-72P.pdf 03 Oct 2022 24 0.35 Mb
5 Patton electronics 2802 Specifications patton-electronics/2802-284.pdf 23 Jul 2022 2 0.19 Mb
6 Harbor Freight Tools PVC WELDING KIT 41592 Assembly and operating instructions manual harbor-freight-tools/pvc-welding-kit-41592-IIY.pdf 30 Mar 2023 7 3.29 Mb

Similar Resources:

  • Grundig

    SE 7230 DOLBY

    (46 pages)
    Materialnummer/Part Number 72010 024 9300Änderungen vorbehalten/Subject to alteration • Printed in Germany WÜE-BS 38 0400 • 8002/8012, 8003/8013, 8005/8015http://www.grundig.comZusätzlich erforderliche Unterlagen für den KomplettserviceAdditionally required Service Documents for the Complete ServiceServiceManualServiceManualServiceTrainingCUC 1832 Ba …
  • Haier

    LET19C430

    (25 pages)
    LCD TV RECEIVERUSER MANUALPlease read this manual carefully before using your television and keep this manual in a good place for future reference.MODEL:LET19C430 LET22C430 LET24C430 …
  • Digital Stream

    DST-HD1100E

    (49 pages)
    User’s Instructions HDTV DIGITAL RECEIVER DST-HD1100E Digital STREAM Technology, Inc. Keumbok BLDG. 45-2 Songpa-ku Bangee-dong Seoul, Korea Tel : + 82 2 415 6500 Fax: + 82 2 415 6540 e-mail : [email protected] © Copyright Digital STREAM Technology, Inc. 2002 …
  • Haier

    LE55D20FM

    (24 pages)
    MODEL:LE55D20FMLED TV RECEIVERUSER MANUALPlease read this manual carefully before using your television and keep this manual in a good place for future reference. …
  • Tauras

    TV3K - TXT

    (8 pages)
    This file is provided FREE OF CHARGE from the electromaniacs.com community You are free to distribute this file to other persons who needs it , but without of charge Also on http://electromaniacs.com you can find thousands of service manuals , schematics free of charge …
  • AT&T

    U-verse TV

    (2 pages)
    In the box:The Wi-Fi Gateway stand should fit snugly into the bottom of the Gateway toward the front and sit flat on the surface as shown above.Phone cable (grey)Ethernet cable (yellow)Wi-Fi Gateway Box 1Your 4-digit passcode. You received a separate letter confirming the 4-digit passcode you designated when placing your order.Packing slip with activatio …

Comments, Questions and Opinions: