Eusso GL2411-AR Operation & User’s Manual

Text of Eusso GL2411-AR User Guide:

• -14- there must be something wrong in your installation procedure. You have to check the following items in sequence: 1. Is the Ethernet cable correctly connected between this product and your computer? Tip: The LAN LED of this product and the link LED of network card on your computer must be lighted. 2. Is the TCP/IP environment of your computers properly configured? Tip:

• -31- 4.9 Misc. Items 1. IP Address of DMZ Host: The DMZ (Demilitarized Zone) Host is a host without the protection of a firewall. It allows a computer to be exposed to unrestricted 2-way communication for Internet games, video conferencing, Internet telephony and other special applications. (Note that this feature should be used only when needed.) 2. Remote Administrator

• Eusso GL2411-AR, -39- 1. Find out the corresponding icon of your server printer, for example, the HP LaserJet 6L. Click the mouse’s right button on that icon, and then select the Properties item: 2. Click the Details item:

• Eusso GL2411-AR, -40- 3. Choose the “PRTmate: (All-in-1)” from the list attached at the Print To item. Be sure that the Printer Driver item is configured to the correct driver of your server printer. 4. Click on the button of Port Settings: Type in the IP address of this product and then click the OK button. 5. Make sure that all settings mentioned above are correct and then click the OK button. 5.2 Configuring on Windows NT Platforms The configuration procedure for a Windows NT platform is similar to that of Windows 95/98 except the screen of printer Properties:

• Eusso GL2411-AR, -43- Appendix A TCP/IP Configuration for Windows 95/98 This section introduces you how to install TCP/IP protocol into your personal computer. And suppose you have been successfully installed one network card on your personal computer. If not, please refer to your network card manual. Moreover, the Section A.2 tells you how to set TCP/IP values for working with this NAT Router correctly. A.1 Install TCP/IP Protocol into Your PC 1. Click Start button and choose Settings, then click Control Panel. 2. Double click Network icon and select Configuration tab in the Network window. 3. Cli

• Eusso GL2411-AR, -32- 4. Discard PING from WAN side: When this feature is enabled, hosts on the WAN cannot ping this product. 5. Non-standard FTP port: You have to configure this item if you want to access an FTP server whose port number is not 21. This setting will be lost after rebooting.

• Eusso GL2411-AR, -33- 4.10 Wireless Setting Wireless settings allow you to set the wireless configuration items. 1. Network ID(SSID): Network ID is used for identifying the Wireless LAN (WLAN). Client stations can roam freely over this product and other Access Points that have the same Network ID. (The factory setting is “default”) 2. Channel: The radio channel number. The permissible channels depend on the Regulatory Domain. The factory setting is as follows: USA/Canada Europe/Australia (ETSI) Japan (All) Channel 6 Spain, France Channel 10 Japan Channel 14 3. WEP

• Eusso GL2411-AR, -36- are not in the "Control table" (please see below), to connect to this device. Association control Check "Association control" to enable the controlling of which wireless client can associate to the wireless LAN. If a client is denied to associate to the wireless LAN, it means the client can't send or receive any data via this device. Choose "allow" or "deny" to allow or deny the clients, whose MAC addresses are not in the "Control table", to a

• -13- Chapter 3 Network Settings and Software Installation To use this product correctly, you have to properly configure the network settings of your computers and install the attached setup program into your MS Windows platform (Windows 95/98/NT/2000). 3.1 Make Correct Network Settings of Your Computer The default IP address of this product is 192.168.123.254, and th

• Eusso GL2411-AR, -7- Provides firmware upgrade via Web Browser or Windows Application. 1.2 Packing List l Wireless broadband router unit l Installation CD-ROM l Power adapter l CAT-5 UTP Fast Ethernet cable

• Eusso GL2411-AR, -29- 4.8 Access Control Access Control allows you to assign different access right for different users. First, you have to divide users into different groups. Users are identified by their IP addresses. You can assign the members of Group 1, 2 and 3. The others are all members of Default Group. Second, you have to assign the access right for each group. Access right can allow or block for access specified TCP and UDP ports. For example: Group Members Access Right Comments Default - Allow () No access right (allow nothing) Group 1

• Eusso GL2411-AR, -35- 4.11 MAC Address Control MAC Address Control allows you to assign different access right for different users and to assign a specific IP address to a certain MAC address. MAC Address Control Check “Enable” to enable the “MAC Address Control”. All of the settings in this page will take effect only when “Enable” is checked. Connection control Check "Connection control" to enable the controlling of which wired and wireless clients can connect to this device. If a client is denied to connect to this device, it means the client can't access to the Internet either. Choose "allow" or "deny" to allow

• -38- Chapter 5 Print Server This product provides the function of network print server for MS Windows 95/98/NT/2000 and Unix based platforms. (If the product you purchased doesn’t have printer port, please skip this chapter.) 5.1 Configuring on Windows 95/98 Platforms After you finished the software installation procedure described in Chapter 3, you

• Eusso GL2411-AR, -2- FCC Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against radio interference in a commercial environment. This equipment can generate, use and radiate radio frequency energy and, if not installed and used in accordance with the instructions in this manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause inte

• Eusso GL2411-AR, -45- 2. Double click Network icon. Select the TCP/IP line that has been associated to your network card in the Configuration tab of the Network window. 3. Click Properties button to set the TCP/IP protocol for this NAT Router. 4. Now, you have two setting methods: A. Get IP via DHCP server

• Eusso GL2411-AR, -21- 4.4 Primary Setup This option is primary to enable this product to work properly. The setting items and the web appearance depend on the WAN type. Choose correct WAN type before you start. 1. LAN IP Address: the local IP address of this device. The computers on your network must use the LAN IP address of your product as their Default Gateway. You can change it if necessary. 2. WAN Type: WAN connection type of your ISP. You can click Change button to choose a correct one from the following four options: A. Static IP Address: ISP assigns you a static IP address. B. Dynamic IP Address: Obtain an IP address from ISP automatically. C. PPP over Etherne

• Eusso GL2411-AR, -25- 3. Domain Name: Optional, this information will be passed to the client. Clients List List the current mapping of the IP and MAC address for each DHCP client. Fixed Mapping In general, DHCP server assigns an IP address chosen from the IP addresses pool randomly. Fixed Mapping allows you to assign a specific IP address to the specified MAC address.

• Eusso GL2411-AR, -10- 2.1.2. Rear Panel Figure 2-2 Rear Panel Ports: Port Description RESET To reset system settings to factory defaults, please follow the steps: 1. Power off the device, 2. Press the reset button and hold, 3. Power on the device, 4. Keep the button pressed about 5 seconds, 5. Release the button, 6. Watch the M1 and M2 LEDs, they will flash 8 times and then M1 flash once per second. 12VDC Power inlet: DC 12V, 1.2A (minimum) PRINTER Printer Port (Optional) COM Serial port (connect analog modem or console cable) 2.2 Procedure for

• Eusso GL2411-AR, -8- Chapter 2 Hardware Installation 2.1 Panel Layout 2.1.1. Front Panel The front panel features four 10/100 Mbps Ethernet ports, one Wide Area network (WAN) port and diagnostic LED indicators. The WAN port connects your DSL or cable modem to the router. The LAN ports are used to connect to your computers or other network devices. LEDs monitor the status of each port. Figure 2-1 Front Panel Port: WAN: the port where you will connect your cable (or DSL) modem or Ethernet router. Port 1-4: the ports where you will connect networked computers and other devices

• Eusso GL2411-AR, -9- LED: LED Function Color Status Description POWER Power indication Green On Power is being applied to this product. M1 System status 1 Orange Blinking This product is functioning properly. On This product is working for some service. M2 System status 2 Orange Blinking This product is being configured or upgraded. Don’t turn it off ! On The LAN port is linked. LAN LAN port activity Green Blinking The LAN port is sending or receiv

• Eusso GL2411-AR, -19- 4.2 Status This option provides the function for observing this product’s working status: A. WAN Port Status. If the WAN port is assigned a dynamic IP, there may appear a “Renew” or “Release” button on the Sidenote column. You can click this button to renew or release IP manually. B. Modem Status. C. Printer Status. The possible kinds of printer status include “Ready”, “Not ready”, “Printing… ”, and “Device error”. When a job is printing, there may appear a “Kill Job” button on the Sidenote column. You can click this button to kill current printing job manually.

• Eusso GL2411-AR, -30- MAC Level The basic Access Control is based on the IP address only. If a user is able to change his IP address, the user will be out of control. The MAC level access control allows you to control the mapping of MAC addresses and IP addresses. You can also control which MAC address is allowed to connect to this device.

• Eusso GL2411-AR, -18- administrator. To log in as an administrator, enter the system password (the factory setting is ”admin”) in the System Password field and click on the Log in button. If the password is correct, the web appearance will be changed into administrator configure mode. As listed in its main menu, there are several options for system administration.

• Eusso GL2411-AR, -34- IEEE 802.11 WEP (64-bit or 128-bit) is used here. 4. WEP Key 1, 2, 3 & 4: When you enable the 64-bit or 128-bit WEP key security, please select one WEP key to be used and then input 10 or 26 hex-decimal (0-9, A-F) digits. MAC Address Control Setup MAC addresses to control which wireless clients can associate to the wireless LAN.

Related Products and Documents (Wireless Router):

Comparable Devices:

Similar Resources:

• Aztech DSL705E (2 pages) www.aztech.comHead Office AZTECH SYSTEMS LTD. 31 Ubi Road 1, Aztech Building Singapore 408694Tel: (65) 6594 2288 Fax: (65) 6749 1198Hong Kong OfficeAZTECH SYSTEMS (H.K) LTD. Rooms 2-10, 3rd Floor, Core Building 1 No. 1Science Park East Avenue HongKong Science ParkShatin,New Territories, Hong KongTel: (852) 2757 1177 Fax: (852) 2753 0578Germany OfficeAZTECH S …

• Honeywell IR800M (2 pages) The IR800M is the new universal wireless infrared sensor from Honeywell. This PIR has all the benets of our existing range of Infrared sensors and wireless peripherals.Features of the IR800M include, compliance to TS EN50131-2-2 Grade 2, Class II, providing exceptional detection capabilities.l Compatible with Domonial, Galaxy and Vista radio modules, …

• Air Live WN-220R (2 pages) P1Quick Setup GuideRegulatory ApprovalsFCC StatementThis equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interferences when the equipment is operating in a commercial area. This equipment generates, uses …

• TP-Link TD-W8901G - Wireless Router (17 pages) CONTENTS English ·································································································· 1 Azərbaycan dili ······························································� …

• Billion BiPAC 7202 (2 pages) (802.11g) ADSL2+ Router BiPAC 7202 / 7202GR2 ▲ BiPAC 7202 ▲ BiPAC 7202GR2Billion’s BiPAC 7202/7202GR2 are all-in-one economical pack of ADSL2+routers which are perfectly designed for users to enjoy rich security, mobility,and faster speed when using ADSL Internet connection. The Router lets youaccess high- …

• NETGEAR WNCE2001 - Ethernet to Wireless Adapter (2 pages) Connect any device with a network port to your existing home wireless network• Wirelessly connects networked home theater devices such as Xbox 360®, PS3™, TiVo®, VUDU, Blu-ray player, and Internet TVs to your home network.• Universal—works with any network enabled device. No need to buy a Wi-Fi adapter that only works with one type of device• P …

Comments, Questions and Opinions: