EverFocus EDR810M Instruction Manual

Text of EverFocus EDR810M User Guide:

• EverFocus EDR810M, 3.4 ALARM SETUP MENU In the ALARM SETUP MENU, we define : (1) ALARM: ENABLE: Enable alarm detection. DISABLE: Disable alarm detection. (2) ALARM TYPE: N. O. : Normal Open alarm. N. C. : Normal Close alarm. (3) ACTIVE CAMERA: Active camera setting, from camera 01~08. You can set the camera which corresponds to the place where the alarm is located. Note: The recording camera number in an event depends on the alarm number, and the active camera images will not be recorded. Example: You assign camera 3 as the active camera to alarm 1. When the alarm 1

• EverFocus EDR810M, 3.2 CAMERA SETUP MENU In the CAMERA SETUP MENU, we define : (1) TITLE: The title setting allows you to assign a title to each camera input. Titling with 12 characters is supported in each channel. The available alphanumeric characters are: 0,1,2,3,4,5,6,7,8,9, A,B,C,D,E,F,G,H,I,J,K,L,M,N,O,P,Q,R,S,T,U,V,W,X,Y,Z, ( ) . , + - / and an empty space. (2) PTZ ID: Select PTZ ID from 001~255 or OFF. The default value is 10+N where N is camera’s number. (3) INSTALL/COVERT: For installation of camera; s

• EverFocus EDR810M, 8. SCREEN DISPLAY SETTING In a full screen display, press SELECT key to pop up the display adjustment window as below: In the screen display setting menu, we define: (1) CAMERA: The display setting of the current camera. (2) BRIGHTNESS: The bright percentage of the current camera; from 0% to 100%. (3) CONTRAST: The contrast percentage of the current camera; from 0% to 100%. (4) COLOR: The color percentage of the current camera; from 0% to 100%. The selected item will show in red color bar. Use Jog to increase or decrease the value. Press ENTER to confirm the setting value and move to next item. After finished setting, p

• EverFocus EDR810M, 20 21 22 Compact Flash Card Slot: Insert a Compact Flash Card to archive an image or video file. HDD LEDs: LEDs for HDD active power (GREEN) and data reading /writing (YELLOW). Remote Control: IR remote control receiver. 23 System LEDs: LEDs for system active POWER , LAN and ALARM display. 19 Shuttle and Jog Dial Shuttle: In the Playback mode, turn the Shuttle dial to fast forward/rewind the video. In the Pause mode, turn the Shuttle dial to slow forward/rewind the video. In the Search mode, turn the Shuttle to change pages. Jog Dial: In the Pause mode, turn the Jog dial to forward/rewind the video. In

• 5.2 SEARCH PLAYBACK (1) TIME / DATE Search Playback Press the SEARCH key to enter the SEARCH MENU. SEARCH In the SEARCH MENU, Dial the Jog clockwise or counterclockwise to change subentry values. Press the ENTER key to go next subentry in search menu setting, and press the DISPLAY key to go last subentry in search menu setting. Press MENU to exit. Press SELECT to start search. Note: If

• EverFocus EDR810M, (4) Slow Forward/Reverse Playback During playback mode, press PAUSE key to freeze the playing back picture. Turn the Shuttle dial clockwise, to start slow forward playback. The speed will show on the status bar of the bottom screen. >> 1/2, 1/4, 1/8, 1/16, 1/32, and press ENTER at the same time to fasten the play speed. PAUSE (5) Image advance Forward/Reverse PAUSE Press PAUSE key to freeze the picture. Turn the Jog dial clockwise to advance the still video image by image. Turn the Jog dial counterclockwise to rewind the still video image by image. The

• EverFocus EDR810M, 3.11 WARNING SETUP MENU 50 3.11.1 FAN FAULT In Warning Setup Menu, you will be able to do warning setting when the following situations occur: In FAN FAULT, we define: (1) BUZZER: Fan buzzer. ENABLE: To enable a buzzer when the fan does not work. DISABLE: To disable fan buzzer. (2) ALARM OUTPUT: The setting of alarms which are NONE and 1, where 1 means the alarm is enabled. (3) ALARM DURATION: PERMANENT (4) NETWORK ALARM: YES: To enable network alarm . NO: To disable network alarm. (5) SEND EMAIL: YES: Send an email when the fan d

• EverFocus EDR810M, (8) SUMMARY : Dial Jog to change items in the SUMMERY table. All camera’s statuses are shown in the SUMMARY table. The table is for checking camera overall statuses only, not for setting. Note: The SUMMARY table also exists in ALARM, MOTION and VLOSS SETUP MENU. All of these SUMMARY tables are also for checking particular overall statuses, not for setting. (9) Copy camera’s setting from a camera to other cameras In order to copy the setting from a camera to other cameras, we provide a setting copy function. Pr

• EverFocus EDR810M, (6) ALARM NETWORK: YES: Enable alarm network. NO: Disable alarm network. (7) SUMMARY: All video loss’s statuses are shown in SUMMARY tables. These tables are for checking video loss overall statuses, but not for setting. 42

• EverFocus EDR810M, APPENDIX B : RS-485 (RJ45) specifications APPENDIX There are two RS-485 (RJ-45) connectors of one port on the back panel of the DVR. Please refer to the following pin assignment for application. 1 2 3 4 5 6 7 8 PIN # NAME 1 2 3 5 4 6 7 8 GND NC NC NC NC NC RX TX 76

• EverFocus EDR810M, Trunk Drive seat ( between seat and wall) or Passenger seat (underneath) ( Users are suggested to use “support” for mounting option) Glove box (inside or underneath) Generator + - - + Vehicle battery (+24V) DVR Fuse(5A) Key start Spilt filter + - Car body On/Off switch Vehicle body Show the wiring on the wiring harness that connects to the electrical system. Possible Installation Locations Inside the Automobile Vehicle: 25

• EverFocus EDR810M, (1) Insert a HDD (IDE) for Video Storage Insert a HDD(IDE) for Video Storage. The HDD should be set as MASTER. After hard disk case is inserted into the hard disk tray, be sure to turn the tray key in lock position. Otherwise, HDD will not be detected. Note: A HDD has to be installed before EDR810/410 is booted, or the EDR810/410 will not detect a HDD until you reboot it with a HDD. Please make sure the HDD indicator light is ON. (2) Connect cable for video/audio input and video/audio out. (3) Turn on system The system will be turned on after connecting to power. Speaker Connect the speaker or other audio devices.

• EverFocus EDR810M, 73 Search from EVENT LIST: I. Select Event Type from Alarm, Motion and Vloss. II. Press Update button to refresh the event list. III. All events of the selected type will be displaying along with Date/Time, event type (represents by a capital letter), camera number (represents by a number), e.g. M02 is the motion event from camera 2. IV. Current page and total page are shown below the event list. Press |<< for first page, << for previous page, >> for next page, >>| for last page, or simply input the page number, then press GO . V. Press Play button to playback the selected event. Search by Time: Search the star

• EverFocus EDR810M, Main Screen The above diagram is the main screen display. The icons on the lower corner of the screen are mainly for control and configuration, those on the right corner are for status indication. If any icon is grayed, it means that the specific function is not accessible in the current mode. The followings are a brief description for each of the icons. 2. STOP: Press this key to stop Video Playback. 3. PLAY: Play back the Video display. 1. REV. PLAY: Reverse Video Playback. 4. STEP FORW

• EverFocus EDR810M, Set up the DAY, START time, END time and then enable the SET in the SCHEDULE SETUP MENU. Please refer to SCHEDULE SETUP MENU, to see setting procedure and more details. 4.2 SCHEDULE RECORDING 4.3 EVENT RECORDING We define two event types which are ALARM and MOTION events can be recorded. After the event recording is enabled, the EDR810/410 will start an event recording when an event occurs. In order to start an event recording, you need: 1. Enable the event in each event setting first. For example, to enable alarm 2 in the ALARM SE

• 3.7 NETWORK SETUP MENU Please Note: Since every Network Configuration is different, please contact your Network Administrator or ISP for how to assign those IP addresses and port numbers. In the CONFIG of the NETWORK SETUP MENU, we define : (1) DHCP: Enable or disable the Dynamic Host Communication Protocol. YES: Enable DHCP service. NO: Disable DHCP service.

• EverFocus EDR810M, Table of Contents 1. PRODUCT INTRODUCTION …………………………………………………………….………… 1.1 FEATURES …………………………………………………………………..…………..…………. 1.2 SPECIFICATIONS……………………………………………………………………………. ……… 1.3 FRONT PANEL KEYPADS …………………………………………………………..…….……… 1.4 BACK PANEL CONNECTORS …………………………………………………………….……… 1.5 MONITOR DISPLAY ………………………

• Title 12-characters title generator for each camera Ethernet RJ45 connectors for network communication Archive Compact Flash Slot and USB for archiving and Archive through Wireless transmission (Optional) RS-232 9-pin female connector for local communication RS-485 for Keyboard connection Audio 2 mono (MIC) inputs, 2 mono (SPEAKER) outputs Power Rate DC 12V/DC 24V Dimens

• EverFocus EDR810M, (6) LANGUAGE: System language can be set in different languages. Note: The available language depends on the different areas and countries. (7) QUICK PLAY: Set up the start play time of the normal play mode. TIME: Quick play time, from 00:00 to 59:59. The default value is 10 minutes. ON: Enable quick play. The video played time is the immediate play time from now. OFF: Disable quick play. Videos will start to be played from the end point of the last play. Note: The recommendatory quick play time is 10 minutes. The video cannot be played due to the video file is not stored to HDD yet if you set a quick play time too short. (8) SYSTEM PASSWORD EN

• EverFocus EDR810M, Quick Install Guide : 1. Unpack Everything Make sure you have everything you need before you begin the installation. 2. Equipment Required The following tools may help you to complete the installation: •Drill •Screwdrivers •Wire cutters 3. Choosing the Location Choose a location for installation that: •Provides convenient access for installing or removing the hard drive •Allows air to flow around the fan vents. Inadequate or improper air flow can impede proper operation of the unit Avoid any location for installation: •That is subject to high vibration •That is subject to high sunlight levels •That is subje

• EverFocus EDR810M, 1.2 SPECIFICATIONS 9 Video Format NTSC/EIA or PAL/CCIR Video Input 4/8 camera inputs (BNC), 1Vp-p/75ohm 1 BNC video out (1Vp-p/75ohm) for Main Monitor 1 BNC video out (1Vp-p/75ohm) for CALL Monitor Video Output 4 video out (1Vp-p/75ohm) for Looping (4 Channels only) Video Compression MPEG4 Recording Resolution 720x240, 720x480 or 360x240 for NTSC 720x288, 720x576 or 360x288 for PAL Video Display Full, PIP, 4, 7, 8/9 and 2x2 Zoom for Live Viewing and Playback Display Resolution 720x240, 720x480 or 360x240 for NTSC 720x288, 720x576 or 360x288 for PAL

• (2) EVENT Search Playback You can change different event search methods if you select “BY EVENT” instead of “BY TIME / DATE”. 7 events which are ALARM, MOTION, VLOSS, A/M, A/V, M/V and A/M/V can be selected. The indications of events show as below. Search all events (ALARM, MOTION and video loss)A / M / V Search MOTION and video loss eventsM / V Search ALARM and video loss

• EverFocus EDR810M, 3.6 VLOSS SETUP MENU In the VLOSS (Video Loss) SETUP MENU, we define : (1) VLOSS: ENABLE: Enable video loss detection. DISABLE: Disable video loss detection. (2) DURATION: Buzzer noise and event record duration of an alarm, from 1 sec to 99 seconds. The default value is 5 seconds. (3) ALARM OUTPUT: The setting of alarms which are NONE and 1, where 1 means the alarm is enabled. (4) ALARM EMAIL: YES: Send an email when video loss occurs. The email address can be set in the NETWORK SETUP MENU. NO: Not to send the email when video loss occurs. (5) BUZZER: Video loss buzzer. ENABLE: To enable a video loss buzzer. DISABLE:

• EverFocus EDR810M, In the COPY MENU, we define: DISK NO: Disk number. It is fixed as “01” in this series. CH NO: Camera channel number. You can select the video of camera you would like to copy. START DATE & TIME: The start time of video you want to copy. END DATE & TIME: The end time of video you want to copy. DEVICE: The storage you want to store the file. There are 2 available devices which are USB and CF CARD. Press SELECT to copy after setting up everything. An upload percentage will show up during video copy. 65

• EverFocus EDR810M, 7. The system allows up to 3 ways to playback video, by EVENT LIST, Time and PTZ Control. (Playback by EVENT LIST, click “Update” button to show list) (Playback by PTZ Control) (Playback by Time) 72

• EverFocus EDR810M, The installations described below should be done by qualified service personnel or system installers. 2.1 PACKING LIST 2. INSTALLATION Please check accessories in the packing before the installation. Camera (VIDEO & AUDIO) Monitor (and Speaker) Internet Alarm (In & Out) IR Remote Controller (Extension Line Connector) USB Device (Storage) RS 232 Please refer to the following diagram for the system connections. Note: Monitor and Camera must be purchased separately. 2.2 SYSTEM FLOORPLAN Call Monitor A

• INSTRUCTION MANUAL Digital Eight Channel Recorder About this manual Before installing and using this unit, please read this Manual carefully. Be sure to keep it handy for later reference. V 1.0 EDR810H/810M/ 410H/410M Date: Aug. 29th 2005

• EverFocus EDR810M, Connect the Camera(s) Connect the power connector from the camera(s) harness into the CAMERA POWER OUT jack on the back panel of the DVR. Connect the primary camera(s) video connector to the CAMERA INPUT and the audio connector to the AUDIO INPUT in the back panel. Adjust the camera(s). After the camera is installed, connect a monitor directly to the camera and observe the image. Make any adjustment if necessary. Installing the Camera(s) and Monitor The DVR is typically connected to one camera installed inside the car. Other camera(s) can also be installed in

More Instructions:

	EverFocus EDR810M Specifications 21-03-2024 2	DOWNLOAD
	EverFocus EDR810M Instruction manual 07-02-2023 84	DOWNLOAD
	EverFocus EDR810M Operator's quick manual 09-07-2023 2	DOWNLOAD
	EverFocus EDR810M Specifications 22-02-2024 2	DOWNLOAD

Related Products and Documents (Voice Recorder):

Comparable Devices:

Similar Resources:

• LogTag Recorders TRID30-7 (16 pages) TRID30-7Temperature Recorder with Display and 30 Day Statistics MemoryProduct User GuideDocument Release Version: 1.3Published 1 September 2016Copyright © LogTag® Recorders , 2004-2016LogTag Recorders Ltd …

• YOKOGAWA ScopeCorder DL350 (258 pages) ScopeCorderDL350Features GuideIM DL350-01EN2nd Editionnbn @ nbn. at | ww w. nbn. atTel. +43 316 40 28 05 | Fax +43 316 40 25 06 Riesstraße 146, 8010 Graznbn Austria GmbH …

• iVR IVR-L1 (28 pages) ENGLISH简体中文繁體中文 IVR Voice RecorderFor product information and support, visitIVR-L1 (2GB)IVR-L1 (4GB)IVR-L1 (8GB)Specifications are subject to change without notice.User Manual使用手册使用手冊www.ivr.com.hk / www.ivr.tw / global.ivr.com.hk說明書內容如有任何變動, 將不另行通知。4GB …

• TS-market EDIC-Mini Tiny (10 pages) www.ts-market.com Operation manual for EDIC-mini Tiny Digital voice recorders Contents Specifications …………………………………………………………………………………………………..………… 1 Main technical characteristics………………………………………….………………………………………… …

• Talking Products Micro-Speak Plus (5 pages) 8GB Micro-Speak Plus User Guide Thank you for purchasing the Micro-Speak Talking Digital Voice Recorder from Talking Products Limited and A T Guys. Let’s get you oriented so you can use your new recorder right away. Place the unit so the buttons are face up and closer to you. The speaker and microphone are hidden behind the grill on the top half of the u …

• Lumens VS-LC101 (73 pages) VS-LC101/VS-LC102 CaptureVision Station [Important] User Manual - English To download the latest version of Quick Start Guide, multilingual user manual, software, or driver, etc., please visit Lumens http://www.MyLumens.com/support.php …

Comments, Questions and Opinions: