Excalibur AL-1510-EDP Operation Manual

Text of Excalibur AL-1510-EDP User Guide:

• Excalibur AL-1510-EDP, Complete Programmable Features Matrix Features Ignition on, off, then press Valet Switch 5 times (Status Light turns on steady). # Feature Default Setting Option 2nd Option 3rd Option 1 SecureCode 1 & 0 2 stages, of up to 9 presses each (total of 99 possible combinations) 2 Last Door Arming OFF (L) ON w/o doorlock (U) ON w/ doorlock (2) 3 Automatic Rearming OFF (L) ON w/o doorlock (U) ON w/ doorlock (2) 4 Starter Interrupt Functions Alarm only (L) Off (U) Automatic (2) 5 Igni

• Valet Switch Status Light Congratulations for your choice of the most versatile, fully-featured vehicle security and convenience system available today, the Excalibur AL-1510-EDP by Omega Research and Development. To enjoy the most from your new system, please take a few moments to learn about the principal user components, and the basic operation of the system. These subjects are

• Excalibur AL-1510-EDP, Feature #19 Remote Activated Anti-Carjacking Protection Factory Default Setting Off ( press “disarm/unlock” button to program ) Option: On ( press “arm/lock” button to program ) This form of Anti-Carjacking is initiated by a signal from the controller or transmitter. The Anti-Carjacking protection, including the three ways to initiate it are described on page 21. Feature #20 Open Door Warning Upon Arming Factory Default Setting Off (press “disarm/unlock” button to program) Option: On (press “arm/lock” button to program) When this feature is turned on, if one of the vehicle&a

• Excalibur AL-1510-EDP, “II” or “ : ” • Pressing the “ II ” button for two seconds can be used to activate an extra output, known as the “2nd channel”, for an optional function such as trunk release. • Pressing and releasing this button twice arms or disarms the system without the confirmation chirps. • Pressing this button immediately after arming will leave the alarm armed, but with the shock sensor feature bypassed. “P” on the controller only. • The controller has a fifth button, “ P ”, which will illuminat

• Excalibur AL-1510-EDP, Arming Using the Controller or Transmitter The system can always be armed from the controller or transmitter, if the ignition key is “off” and the system is not in the Valet Mode. To arm the system, exit the vehicle, close all of the doors, and simply press and release the “arm/lock” button once. Your Excalibur system is designed to deter theft of both your vehicle and its contents. “Arming” your system turns on the protection, disabling the vehicle’s starter and locking the doors. Once the system is Armed, any in

• Excalibur AL-1510-EDP, Arming Bypass: Upon arming, if any system sensing circuit is inoperable, that circuit only will automatically be bypassed. When an unsecured sensing circuit is in a bypassed state, all other normally operating circuits will be protected. Should the bypassed circuit become secured, it will automatically be reinstated for protection 5 seconds later. When certain protection circuits are bypassed, such as the hood/trunk and impact sensor, and the system is armed, it will indicate this by chirping the siren three times and flashing the parking lights three times instead of the

• Excalibur AL-1510-EDP, While the System is Armed, and should it Trigger While the security system is armed, the Status Light flashes red in color. Should any intrusion attempt be detected, the system will instantly activate, or "trigger". Once triggered, the Excalibur loudly sounds the siren and flashes the parking and interior lights on and off. must be closed to initiate the Last Door Arming sequence. To temporarily prevent the system from automatically Last Door Arming, you have these options: put the system into Valet Mode (page 14 and 15), leave the d

• Excalibur AL-1510-EDP, Feature #2 Last Door Arming Factory Default Setting Off (press “arm/lock” button to program) Options: On without doors locking ( press “disarm/unlock” button to program ) On with doors locking (press “II” button to program) “Last Door Arming” has the system automatically arm itself every time you exit the vehicle (the complete operation is described on pages 8 & 9). This feature turns that operation on or off, and with options of having Last Door Arming operate with or without also locking the doors when th

• Excalibur AL-1510-EDP, Safety Disarm/Storm Mode: While the system is activated, i.e. sounding the siren and flashing the lights, pressing the “disarm/unlock” button will disarm the system, but not unlock the doors. This safety feature ensures that the vehicle remain secure should the system require disarming due to being activated from nuisance or malicious false sensory inputs, such as typically produced by severe weather conditions. To remotely unlock the doors if the system is disarmed while activated, simply repeat the disarm operation by p

• The number of Valet Switch presses which are required for the Emergency Override is custom-programmable! This is the SecureCode feature, which is described on page 15 and page 26. The above Emergency Override instructions reflect the “as received from the factory” default setting. Step 3 Within 5 seconds press and release the Valet Switch one time. The system will disarm. Should you fe

• Excalibur AL-1510-EDP, Other Controller and Transmitter Operations The 2nd channel output, which is operated by pressing and holding the controller or transmitter “II” button for 1 second, is designed specifically to operate your vehicle’s electric power trunk release. Your vehicle will respond by releasing the trunk lid or rear hatch, chirping the siren twice, turning on your parking and interior lights for 30 seconds, unlocking the doors, and disarming the system if it was armed. The 2nd channel output will not operate when the ignition switch is "on" unless the vehicle's door is open. If

• Excalibur AL-1510-EDP, The Valet Switch is located in the Window Unit, or optionally, the installer may have instead mounted a separate Valet Switch in a hidden, yet accessible location. Please ensure that you and others who use your vehicle are aware of the location of the Valet Switch and its uses. The Valet Switch has several functions: Using the Valet Switch • It is also used in the procedures for programming features and programming controllers or transmitters to operate the Excalibur system. See the “Programming sections of this manual for details on these uses. • Should your controller or transmitter be lost or become inoperable, the

• To Exit Valet Mode, simply Press & Release the Valet Switch at any time. • The Status Light will turn off to confirm exit from Valet Mode. “SecureCode” allows the user to customize the number of Valet Switch presses which are required to successfully perform an Emergency Override. The basic Emergency Override procedure is described on pages 11-12. Instead of a sing

• Excalibur AL-1510-EDP, The Status Light Security System Status: These are the “normal” operations of the Status Light, indicating the state of the security system. Exceptions to normal operation are the transmitter verification display upon turning on the ignition key, and 1) Off = The security system is disarmed and not performing automatic functions. 2) On Constant = The security system is in the Valet Mode. 3) Flashing Slowly = The security system is fully armed. 4) Flashing Fast = Last Door Arming or Automatic Rearming is in progress. Automatic Transmitter

• Excalibur AL-1510-EDP, • The “DISARM” also shows “ARM”; to indicate the Armed or Disarmed status of the sys- tem. Neither icon is present when the system is in Valet Mode. Controller Icons: The LCD screen on the controller has various icons which indicate system status. When the controller is used to operate the system, it receives back a signal which causes it to chirp (emulating the siren) and display the appropriate icons. Brief descriptions of the icons are: The 2-Way Controller The four system- operating buttons are described on pages 4-7. This section explains the controller’s icons, and how to program the controller’s features. • The digit readout is a cloc

• Excalibur AL-1510-EDP, • If an optional remote start unit is added to the AL-1510-EDP, the “start” icon at the rear of the vehicle can confirm remote starting, and it is accompanied by a musical melody. The 3rd channel must be operated first, and then if the AL- 1510-EDP detects that the ignition circuit is turned on it will display this icon. • The “DOOR” icon will indicate that the system was activated via the door detection circuit. The controller chirps until any button is pressed, and the icon remains flashing until the ignition is turned on. • On the vehicle’s windshield is a “hammer” and “impact” icon. When the shock sensor detects light impact, causing the sys

More Instructions:

	Excalibur AL-1510-EDP Operation manual 24-09-2022 20	DOWNLOAD
	Excalibur AL-1510-EDP Installation instructions manual 22-08-2022 18	DOWNLOAD

Related Products and Documents (Car Alarm):

Comparable Devices:

Similar Resources:

• Fortin EVO-ONE (10 pages) 1-Page_enteteWARNINGATTENTION* HOOD PINHOOD STATUS : THE HOOD PIN SWITCH (INCLUDED)MUST BE INSTALLED IF THE VEHICLE CAN BE REMOTE STARTED WITH THE HOOD OPEN. CONTACTDE CAPOTSECURITY STICKERAUTOCOLLANT DE SÉCURITÉMANDATORY INSTALL | INSTALLATION OBLIGATOIRENotice: the installation of safety elements are mandatory. The hood pin and the sticker are essenti …

• Clifford AvantGuard 4 (24 pages) Standard Features of the AvantGuard 4System ComponentsOne prewired 24-pin connector One Extended Range Receiver One prewired 12-pin connector One LEDOne prewired 14-pin connector One PlainView 2 Coded Valet SwitchOne prewired 9-pin connector One Digital Tilt/Motion SensorOne AvantGuard 4 Control Unit One Warranty CardOne Self-Powered SmartSiren 4 One Owner …

• Fortin EVO-ALL (7 pages) ADDENDUM - SUGGESTED WIRING CONFIGURATION ADDENDA - SCHÉMA DE BRANCHEMENT SUGGÉRÉALLREV.: 20180406ALLREV.: 20180406ONLY COMPATIBLE WITH AUTOMATIC TRANSMISSION VEHICLES.COMPATIBLE AVEC VÉHICULE À TRANSMISSION AUTOMATIQUE SEULEMENT.Vehicle functions supported in this diagram (functional if equipped) | Fonctions du véhicule supportées dans ce diagramme ( …

• Omega Crime Guard 745i3 (20 pages) COPYRIGHT 1999: OMEGA RESEARCH & DEVELOPMENT, INC.OPERATION MANUAL745i3Page 2About Your New Crime Guard System ................................. 3Using Your Crime Guard System........................................... 4Remote Arming By Transmitter............................................... 4-5Arming BypassLast Door Arming By Exiting The Car....... …

• Skybrake DD2+ (2 pages) versija 01, 1.06.2008_120114DD2+ installation manual1. OPERATING PRINCIPAL OF THE SYSTEMA vehicle equipped with the Skybrake DD2+ anti-theft device can only be used if the Personal Transceiver (PT) is within range – either inside the vehicle or not further than two meters from it. If the engine is switched on without t …

• PUREGEAR PureCam (17 pages) 1 PureGear PureCam User Manual Congratulations on purchasing the PureGear PureCam. This PureCam User Manual covers the following: 1. Before You Get Started • Inside your PureCam package • System and vehicle requirements 2. Setting Up Your PureCam • Operating your PureCam • PureCam menu overview o Photo o Video o Settings ▪ Resolution � …

Comments, Questions and Opinions: