Dake E-16 Instruction Manual And Parts List

Text of Dake E-16 User Guide:

• Dake E-16, 4/29/03 Manual V-16, V-24, VH-24, V-40 & VH-40 1 – Section I JOHNSON VERTICAL BAND SAWS INSTRUCTION MANUAL AND PARTS LIST SECTION I – Manual FOR MODELS E-16 V-16 V-24 VH-24 V-40 VH-40 N MANUAL AND PARTS LIST MODEL: ________________________________________ SERIAL NUMBER: ________________________________ DATE PURCHASED: ______________________________ DAKE Divisi

• Dake E-16, 4/29/03 Manual V-16, V-24, VH-24, V-40 & VH-40 2 – Section I If machine is to be operated At 440 volt 3 phase power, please read the following warning. FOREWORD These instructions cover the installation and operation of vertical band saws. Attention to maintenance and service will afford many years of trouble free operation. We suggest that these instructions be retained by the department or individual responsible for the machine and kept in a readily accessible location

• Dake E-16, 4/29/03 Manual V-16, V-24, VH-24, V-40 & VH-40 3 – Section I SECTION I - TABLE OF CONTENTS Specifications ....................................................................................... 4 Machine Features ................................................................................ 5-6 Unloading ............................................................................................. 7 Installation ............................................................................................ 7 Electrical ........

• Dake E-16, 4/29/03 Manual V-16, V-24, VH-24, V-40 & VH-40 4 – Section I SPECIFICATIONS Model Number: V-16 V-24/VH-24 V-40/VH-40 Capacity: Throat Inches 16 23-1/2 41 Work Height Inches 11 12-1/2 12-1/2 Table: Work Table Inches 23-1/2 x 23-1/2 26-3/8 x 26-3/8 26-3/8 x 26-3/8 Auxiliary Inches -- 9 x 22-3/8 15-1/2 x 21-1/2 Height from Floor Inches 38 42 41 Travel-Manual or Hydraulic Inches -- 10 10 Tilt-Left Degree 10 10

• Dake E-16, 4/29/03 Manual V-16, V-24, VH-24, V-40 & VH-40 7 – Section I MACHINE UNPACKING AND INSTALLATION UNLOADING: Remove the shrink-wrap covering the machine, carefully as not to damage painted surfaces, electrical or hydraulic parts. Carefully inspect the machine for physical damage. If damage is noted, notify the truck line at once. They may require inspection, and that a claim be filed. Check that all standard accessories are with the machine. Some accessories may be boxed or placed behind access doors or chip drawer. (See figure 2 & 3) The band saws are provided wi

• Dake E-16, 4/29/03 Manual V-16, V-24, VH-24, V-40 & VH-40 8 – Section I FILLING THE SPEED REGULATOR 1. Turn the saw on. 2. Screw the handwheel in. 3. Turn the saw off once handwheel is in. 4. Remove the mounting screws (item 6). 5. Remove the plug from the cylinder (Item 3). 6. Turn screw out. 7. Add oil (Lightweight hydraulic oil) slowly while turning the wheel out. 8. When it is completely full, replace the plug (Item 3). 9. Re-mount the cylinder to the saw body.

• Dake E-16, 4/29/03 Manual V-16, V-24, VH-24, V-40 & VH-40 9 – Section I WHEEL ALIGNMENT V-16 & V / VH-24 Note: This alignment is factory set, but may need adjustment when replacing blade. Two wheel machines have a bottom wheel that drives the saw blade and a top idle wheel that is adjustable to facilitate blade tracking. The edges of the wheels are fitted with a composite material to accommodate the tooth set. The idle wheel may be adjusted by loosening the knurled locking collar and turning the black knob in the

• Dake E-16, 4/29/03 Manual V-16, V-24, VH-24, V-40 & VH-40 10 – Section I BLADE TENSIONING The blade indicator is located inside the upper wheel compartment, on the lower left side of the idle wheel. (See machine features graphic) The indicator has an arrow mounted on the horizontal plane, with a corresponding scale for blade tensioning. The scale has two legends, one reads inches from 0 - 1”, the second reads mm 0 - 25 mm. This allows tensioning either standard or metric blade widths. With out tension on the blade, the indicator should read zero. As tension is applied to the blade the needle will move accordingly, and should be tightened until the corr

• Dake E-16, 4/29/03 Manual V-16, V-24, VH-24, V-40 & VH-40 11 – Section I An analysis of the work to be performed should be made and the proper blade selected. The blade should always be inspected before installing on the machine. Things to look for should be the smoothness on the sides and back edge of the weld, look for any missing teeth, or impacted chips. The blade guides may now be selected and inserted into both the upper and lower guide holders. Proper adjustment of these guides takes place when they form a complete “V” shape (see graphic bel

• Dake E-16, 4/29/03 Manual V-16, V-24, VH-24, V-40 & VH-40 12 – Section I HIGH SPEED ROLLER GUIDES Applications and Advantages: Friction and abrasive cutting, filing operations, aluminum and woodcutting. These guides eliminate having to change inserts when changing to blades of different widths. Requirements for Installation: These roller guides must be installed using a new 1/2” blade width band for proper alignment. The 1/2” band should be tracked within the approximate center line of the band wheels. Note: Be certain band wheels are clean are free of any foreign material build up before proceeding. Tools / Hardware Required: Drill - 7/16”

• Dake E-16, 4/29/03 Manual V-16, V-24, VH-24, V-40 & VH-40 13 – Section I 4: Insert the mounting stud (B) into the guide casting (A). Keep the stud flush with the front of the casting. Keeping the mounting stud flat area on the bottom, tighten securely the set screw (C) on the bottom of the casting. 5: Insert this stud and guide assembly into the 7/16” hole in the guidepost. Make sure upper roller guide is plumb with the guidepost. Lightly tighten set screw you installed in the guidepost. Lower Guide Installation: 6: Remove lower blade guide. Replace this guide with the high speed guide containing the mounting bracket with slotted hole, reusing existing

• 4/29/03 Manual V-16, V-24, VH-24, V-40 & VH-40 14 – Section I Repeat this process for the lower guide assembly. Note: Upper guide stud may be adjusted in or out in the guide post to allow proper clearance for blade, and for alignment with lower guide. Align backup bearing as previously described for upper guide. Tighten both set screws whe

• Dake E-16, 4/29/03 Manual V-16, V-24, VH-24, V-40 & VH-40 15 – Section I Note: Occasionally the drive wheel may have to be jogged by hand to engage the transmission lever. The variable speed is achieved through the use of a variable regulator. (Figure 3) This is turned clockwise or counter clockwise to obtain an increase or decrease in blade speed, in either range. Adjust until desired speed is reached as read on the blade speed gauge. (Figure 4) WARNING: DO NOT ADJUST THE VARIABLE SPEED CONTROL (FIGURE 3) SPEED UNLESS THE MACHINE IS IN OPERATION! FAILURE

• Dake E-16, 4/29/03 Manual V-16, V-24, VH-24, V-40 & VH-40 16 – Section I SAW BLADE SELECTION MATERIAL SHAPE MATERIAL SHAPE MATERIAL SHAPE MATERIAL IN INCHES TOOTH SELECTION TOOTH SELECTION TOOTH SELECTION 0 14 / 18 14 / 18 14 / 18 .1 14 / 18 14 / 18 14 / 18 .2 14 / 18 14 / 18 14 / 18 .3 10 / 14 14 / 18 10 / 14 .4 8 / 12 10 / 14 8 / 12 .5 8 / 12 8 / 12 6 / 10 .6 6 / 10 8 / 12 5 / 8 .7 6 / 10 6 / 10 5 / 8 .8 5 / 8 6 / 10 5 / 8 .9 5 / 8 5 / 8 5 / 8 1 5 / 8 5 / 8 4

• 4/29/03 Manual V-16, V-24, VH-24, V-40 & VH-40 17 – Section I MATERIAL ALLOY 1/2" 1" 2" 4" 7" 12" 1100,2011,2017,2024 fpm 568 sipm 7 fpm 577 sipm 11 fpm 536 sipm 16 fpm 498 sipm 21 fpm 451sipm 23 fpm 389 sipm 24 ALUMINUM ALLOY 3003,5052,5086,6061 fpm 568 sipm 7 fpm 577 sipm 11 fpm 536 sipm 16 fpm 49

• Dake E-16, 4/29/03 Manual V-16, V-24, VH-24, V-40 & VH-40 18 – Section I MATERIAL ALLOY 1/2" 1" 2" 4" 7" 12" A-6 fpm 227 sipm 3 fpm 223 sipm 4 fpm 214 sipm 6 fpm 199 sipm 9 fpm 180 sipm 9 fpm 156 sipm 10 COLD-WORK A-2 fpm 204 sipm 3 fpm 200 sipm 4 fpm 193 sipm 6 fpm 179 sipm 8 fpm 162 sipm 8 fpm 140 sipm 9 TOOL STEEL A-10 fpm 182 sipm 2 fpm 178 sipm 3 fpm 171 sipm 5 fpm 159 sipm 7 fpm 144 sipm 7 fpm 125 sipm 8 D-2 fpm 102 sipm 1 fpm 100 sipm 2 fpm 96 sipm 3 fpm 90 sipm 4 fpm 81 sipm 4 fpm 70 sipm 4 HOT-WORK TOOL H-11,H-12,H-13 fpm 216 sipm 3 fpm 212 s

• Dake E-16, 4/29/03 Manual V-16, V-24, VH-24, V-40 & VH-40 19 – Section I NITRONIC 50,60 fpm 68 sipm 1 fpm 67 sipm 1 fpm 64 sipm 2 fpm 60 sipm 3 fpm 54 sipm 3 fpm 47 sipm 3 MATERIAL ALLOY 1/2" 1" 2" 4" 7" 12" MARTENSITIC STAINLESS STEEL GREEK ASCOLOY fpm 108 sipm 1 fpm 106 sipm 2 fpm 102 sipm 3 fpm 95 sipm 4 fpm 86 sipm 4 fpm 74 sipm 5 416 fpm 216 sipm 3 fpm 212 sipm 4 fpm 204 sipm 6 fpm 189 sipm 8 fpm 171 sipm 9 fpm 148 sipm 9 FREE MACHINING 440 F fpm 182 sipm 2 fpm 178 sipm 3 fpm 171 sipm

• Dake E-16, 4/29/03 Manual V-16, V-24, VH-24, V-40 & VH-40 20 – Section I MATERIAL ALLOY 1/2" 1" 2" 4" 7" 12" INCONEL 751,X750 fpm 79 sipm 1 fpm 79 sipm 1 fpm 79 sipm 1 fpm 79 sipm 1 fpm 79 sipm 1 fpm 79 sipm 1 NICKEL BASE WASPALOY fpm 79 sipm 1 fpm 79 sipm 1 fpm 79 sipm 1 fpm 79 sipm 1 fpm 79 sipm 1 fpm 79 sipm 1 ALLOY MONEL K500 fpm 74 sipm 1 fpm 72 sipm 1 fpm 70 sipm 2 fpm 65 sipm 3 fpm 59 sipm 3 fpm 51 sipm 3 (*HASTELLOY) INCOLOY 901,903,926 fpm 68 sipm 1 fpm 67 sipm 1 fpm 64 sipm 2 fpm 60 sipm 3 fpm

• Dake E-16, 4/29/03 Manual V-16, V-24, VH-24, V-40 & VH-40 21 – Section I 38 353 40% HYDRAULIC FEED TABLE Machines equipped with a hydraulic feed table (VH models) have a pumping unit in the base. The system has an adjustable relief valve, which is factory preset at 400 p.s.i. This setting may be reduced to afford greater sensitivity for cutting soft or thin materials. Pressures may be lowered by turning the square nut located on the top right hand side of the reservoir. (See below gra

• Dake E-16, 4/29/03 Manual V-16, V-24, VH-24, V-40 & VH-40 22 – Section I Cut the blade ends accurately and at right angles. (See graphic below) Check abutment against the stop for a cut at right angles. Proper welding can only be achieved if the blade ends are cut with out a burr and at right angles. (Also see trouble shooting section) 2. ADJUSTMENT The initial jaw gap and upset force must be adjusted and proportioned to the cross sectional area of the blade being welded. A greater jaw gap will allow a wider or thicke

• 4/29/03 Manual V-16, V-24, VH-24, V-40 & VH-40 23 – Section I After welding loosen the pressure clamps (7 fig. 1) and set the jaws to the wide annealing position by turning the upsetting pressure switch (2 fig. 1) counter clockwise. Re-clamp the blade so that the weld is in the center between the jaws. Operate the annealing switch (8 fig.1) until the

• 4/29/03 Manual V-16, V-24, VH-24, V-40 & VH-40 24 – Section I If incoming voltage is high reverse this procedure. If incoming voltage is low, the welder transformer has taps that can be set to a 10% increase or decrease. SHOCK HAZARD! ONLY A QUALIFIED ELECTRICIAN SHOULD ATTEMPT THIS. ALWAYS CONTACT DAKE BEFORE REMOVING THE WELDER. If the welder does not shut

• Dake E-16, 4/29/03 Manual V-16, V-24, VH-24, V-40 & VH-40 25 – Section I RIP FENCE Standard all models (figure 2) (Part number 714805 – Model 24/40) (Part number 714869 – Model 16) Used for cutting material in accurate straight lines. To attach, insert T-bolt provided in the T-slot in the front of the table. Slide into the desired position and tighten handle. PROFILE CUTTING ATTACHMENT Standard on VH-24 / VH-40 models (figure 3) (Part number 714821) This device is used for cutting irregular shapes with the use of the hydraulic table.

Related Products and Documents (Saw):

Comparable Devices:

Similar Resources:

• Pearl VX5WV (16 pages) serial number -Caution! Read Safety and General Instructions carefully before using saw for the first time.You should record the Serial Number of your Tile Saw on this Owner’s/Operator’s Manual and on the Warranty Card. The Warranty Card must be sent back with all the required pertinent information for the warranty to take effect.REV. 1Pearl Abrasive C …

• Skil 4230 (8 pages) 24230400 W1,65 kg216mm5mm165mm10mm4mm16mm3500p/min4330450 W1,65 kg4374450 W1,7 kg4375500 W1,7 kg70mm10mm4mm16mm400-3500p/min70mm10mm4mm16mm400-3500p/min80mm16mm400-3500p/minXP SKIL 4230/4330/4374/4375 28-05-2002 12:43 Pagina 2 …

• Ryobi ETS-1526AL (14 pages) ETS-1526ALTABLE SAWOWNER’S OPERATION MANUALCAUTION: Carefully read through this entire owner's manual before using yourTABLE SAW.SAVE THIS MANUAL FOR FUTURE REFERENCE.Your new table saw has been engineered and manufactured to Ryobi's high standard for dependability, ease of operation, and operator safety. Properly cared for, it will give you year …

• Genesis GSS160 (48 pages) 16" Variable Speed Scroll SawScie à chantourner à vitesse variable de 16 po Sierra de calar de 16”, de velocidad variableGSS160Operator's Manual Manuel d’utilisation Manual del Operario …

• Milwaukee 0729-20 (15 pages) DEEP CUT BAND SAWSCIE À RUBAN POUR COUPE PROFONDESIERRA CONTINUA PARA CORTES PROFUNDOSCat. No.No de cat.Cat. No.0729-20OPERATOR'S MANUALMANUEL de L'UTILISATEURMANUAL del OPERADORTO REDUCE THE RISK OF INJURY, USER MUST READ OPERATOR'S MANUAL.AFIN DE RÉDUIRE LE RISQUE DE BLESSURES, L'UTILISATEUR DOIT LIRE LE MANUEL DE L& …

• Power Craft PSMS 2100 (18 pages) PSMS 2100Sliding Mitre SawArtikel-Nr.: 4300669Ident-Nr.: 01017Komponenten / ErsatzteilePosition Artikel-Nr. BeschreibungPosition Artikel-Nr. Beschreibung52 430066901052 Fence 63 430066901063 Bolt 64 430066901064 Outer Flange 67 430066901067 Inner Flange 92 430066901092 Carbon Brush (pair) 115 430066901115 Movable Guard 129 430066901129 Handle 130 430 …

Comments, Questions and Opinions: