Manualios.com

Toshiba TOSVERT VF-S15 series Function Manual

  • TOSVERT VF-S15 series Computer Accessories
  • maOHlab8g21MA
  • Function Manual
  • PDF / Adobe Acrobat Reader
  • 51

Toshiba TOSVERT VF-S15 series Manual Online:

3.95, 1055 votes
Toshiba TOSVERT VF-S15 series User Manual
Toshiba TOSVERT VF-S15 series User Guide
Toshiba TOSVERT VF-S15 series Online Manual

Text of Toshiba TOSVERT VF-S15 series User Guide:

  • Toshiba TOSVERT VF-S15 series, E658130 - 17 - 5.5. I/O signal list 5.5.1. One station is occupied (CC-Link Ver.1) (c122=0) This option occupies one station area of the buffer memory of the PLC. In the case of c122 = 0, there are remote I/O (RX, RY both 32 bits) and the remote register (RWw, RWr both 4 word) in the communication data for one station area. Remote I/O (Default value = 0) Inverter (Slave) → PLC (Master) PLC (Master) → Inverter (Slave) Device No. Signal Device No. Signal RXn0 Forward running RYn0 Forward rotation command RXn1 Reverse running RYn1 Reverse rotation command RXn2 Output terminal 1 (RY-RC) RYn2 Input termina

  • E658130 - 16 - 5.4. Basic functions This clause shows the basic function of this CC-Link option using by CC-Link communication. 5.4.1. Run and frequency operation command The PLC program can operate the inverter to run, stop, set the operation frequency and change the parameters. If the PLC controls these operations, select the command mode and the

  • Toshiba TOSVERT VF-S15 series, E658130 - 34 - 5.5.12. Description of input terminal information Data composition of input terminal information (Code No. = 0FH). Bit Terminal name Function (parameter name) 0 1 0 F Input terminal function selection 1A(f111) / 1B(f151) / 1C(f155) 1 R Input terminal function selection 2A(f112) / 2B(f152) / 2C(f156) 2 RES Input terminal function selection 3A(f113) / 3B(f153) 3 S1 Input terminal function selection 4A(f114) / 4B(f154) 4 S2 Input terminal function selection 5(f115) 5 S3 Input terminal function selecti

  • Toshiba TOSVERT VF-S15 series, E658130 - 44 - 6.8. Program example for trip information reading Example 8 shows a ladder logic to read the trip information of station 1 inverter to D1. Trip history No. 1, No. 2 reading code number: 74H (hexadecimal) The reply code at the time of instruction code execution is set to D2. For example of trip information Read dara: 2D0EH b15 b8 b7 b0 0 01 0 1 10100001110 (2DH) (0EH) Past trip code Current trip code e-13( Error code: 2DH) ol2(Error code: 0EH) " Over speed fault &quo

  • Toshiba TOSVERT VF-S15 series, E658130 - 33 - 5.5.11. Description of monitor code Divide the monitor code (RWw n) into half and select the monitor value 1 (RWr n) from the lower 8 bits and the monitor value 2 (RWr n) from the upper 8 bits. For Example: When output voltage is selected for the monitor value 1 and output torque is selected for the monitor value 2. -> The monitor code is 0703H. Address Upper 8 bits Lower 8 bits RWw n Monitor value 2 Monitor value 1 RWw n+4 - Monitor value 3 RWw n+5 - Monitor value 4 RWw n

  • Toshiba TOSVERT VF-S15 series, E658130 - 38 - 6.1. Program example for reading the inverter status Example 1 shows a ladder logic to read the inverter status. Y30 of the output unit is turned on when inverter of station 2 is forward running 0 0 0 0 * 0 0 0 0 0 0 0 0 0 0 1 RX0 to RXF RX10 to RX1F RX20 to RX2F RX30 to RX3F Remote input Station1 Station 2 Inverter status b0: Forward running b1: Reverse running b2: Output ter

  • Toshiba TOSVERT VF-S15 series, E658130 - 46 - 6.10. Instructions 1.Programming instructions 1.1 Since the buffer memory data of the master station is kept transferred (refreshed) to/from the inverters, the TO instruction need not be executed every scan in response to data write or read requests. The execution of the TO instruction every scan does not pose any problem. 1.2 If the FROM/TO instruction is executed frequently, data may not be written reliably. When transferring data between the inverter and sequence program via the buffer memory, perform the handshake to confirm that data has been written without error. 2. Operatin

  • Toshiba TOSVERT VF-S15 series, E658130 - 28 - 5.5.8. Instruction Codes Code No. Item Description 1003H Command mode selection read 2003H Command mode selection write 0: Terminal block 1: Panel keypad (including extension panel) 2: RS485 communication 3: No function 4: Communication option 1004H Frequency setting mode selection read 2004H Frequency setting mode selection write 0: Setting dial 1(save even if power is off) 1: Terminal VIA 2: Terminal VIB 3: Setting dial 2(press in center to save) 4: RS485

  • Toshiba TOSVERT VF-S15 series, E658130 - 7 - 4. Installation on inverter Refer to VF-S15 option adapter instruction manual (E6581838) for the installation on the inverter. Mandatory The following steps must be performed before installing. 1. Shut off all input power. 2. Wait at least 15 minutes and check to make sure that the charge lamp is no longer lit. 4.1. Connection cable In the CC-Link system, use CC-Link dedicated cables. If the cable used is other than the CC-Link dedicated cable, the performance of the C

  • E658130 - 41 - 6.5. Program example for monitoring the output frequency Example 5 shows a ladder logic to read the output frequency of station 1 inveter to D1. Output frequency reading code number: 0001H (hexadecimal) When the output frequency is 50Hz, D1 is 1388H (5000) (unit: 0.01Hz). Refer to 5.5.11 for detail. Read output

  • Toshiba TOSVERT VF-S15 series, E658130 - 43 - 6.7. Program example for parameter reading Example 7 shows a ladder logic to read parameter f311 of station 1 inverter to D2. f311: Reverse-run prohibition reading code number: 1311H (hexadecimal) The reply code at the time of instruction code execution is set to D1. Refer to 5.5.8 for detail. Check the ready of the station 1 X0 X0F X1 ( M0) SW80.0 M0 X20 [ PLS M300] M300 [ SET M301] M301 X100F [ MOV H1311 W102] [ SET Y100F] [ RST M301] [ SET M302] M302 X10

  • Toshiba TOSVERT VF-S15 series, E658130 - 39 - 6.2. Program example for setting the operation mode Example 2 shows a ladder logic to write data in the inverter. The operation mode of station 1 inverter can be changed to network operation. Operation mode writing code number: 2003H (hexadecimal) Network operation set data: 0004H (hexadecimal) The reply code at the time of instruction code execution is set to D2. Check the ready of the station 1 Write operation mode write code (2003H) to RWw2 and set data (0004H) to RWw3. X0 X0F X1 ( M0) SW80.0 M0 X20 [ PLS M300] M300 [ SET M301] M301 X100F [ MOV H2003 W102

  • Toshiba TOSVERT VF-S15 series, E658130 - 45 - 6.9. Program example for resetting the inverter at inverter error Example 9 shows a ladder logic to reset the station 2 inverter. The above inverter reset using RY3A may be made only when an inverter error occurs. Also, inverter reset can be made independently of the operation mode. X0 X0F X1 SW80.1 M X103 X2 [ M0 [Y103A] [ END Check the ready of the station 2 Turn on the error reset request flag (RY3A). Then, turn off the error reset request flag (RY3A) when the error Example

  • Toshiba TOSVERT VF-S15 series, E658130 - 14 - 5.3. CC-Link function setting 5.3.1. Station number setting Use parameter c120 to set station number of the inverter. Set this parameter within the range of 1 to 64. Title Function Description c120 CC-Link station number selection 1 to 64 *Use different station numbers for different devices. (If different devices have the same station number, the communication cannot be performed properly.) ・ Set consecutive numbers for the station numbers. (Do not skip a number in sequence like "station number 1 - station number 2 - station number 4".) ・The station nu

  • Toshiba TOSVERT VF-S15 series, E658130 - 21 - 5.5.6. Detail of input and output signals 1. Output signals (Master -> Inverter) The output signals from the master unit are indicated. (Input signals to inverter) Device No. Signal Description RYn0 Forward run command OFF: Stop command ON: Forward run command*** RYn1 Reverse run command OFF: Stop command ON: Reverse run command*** RYn2 Input terminal function 3(S1) The function depends on input terminal selection 3 (c142) * RYn3 Input terminal function 4(S2) The function depends on input terminal selection 4 (c143) * RYn4 Input terminal function 5(S3) The function depends on input terminal selection 5 (c144) * RYn5 Input terminal funct

  • E658130 - 20 - 5.5.5. Trip history When “Quadruple setting” or “Octuple setting” of CC-LINK V.2 is selected, the past trip information can be referred to by the following methods. Upper 8 Bits Trip history No. Upper 8 Bits Trip history No.. RWr n+8 Lower 8 Bits Trip code RWw n+8 Lower 8 Bits Reserved RWr n+9 Trip information (output frequency) RWw

  • Toshiba TOSVERT VF-S15 series, E658130 - 31 - Error code Decimal No. Hexadecimal No. Description Trip display 50 32H Analog input break detection fault e-18 51 33H CPU communications error e-19 52 34H Over torque boost fault e-20 53 35H CPU fault 2 e-21 55 37H Optional unit fault 2 e-23 58 3AH CPU fault 3 e-26 62 3EH Main module overload ol3 64 40H PTC fault e-32 65 41H Over-torque trip 2 ot2 69 45H Servo lock fault e-37 71 47H Auto-tuning error (PM motor) e-39 72 48H Over-torque / Overcurrent fault otc3 73 49H Small-torque / Small -current fault utc3 84 54H Auto-tuning e

  • Toshiba TOSVERT VF-S15 series, E658130 - 8 - 4.3. Connection of CC-Link master unit and inverter The example of the connection of the CC-Link master unit and the inverter is shown.。 CC-Link Master Unit DA DB DG SLD FG CCL003Z DA DB DG SLD FG Inverter VF-S15 R/L1 S/L2 T/L3 U/T1 V/T2 W/T3 I M Motor *Connection of Several Inverters Factory Automation can be applied to several inverters which share a link system as CC-Link remote device stations and are controlled and monitored b

  • E6581830 TOSVERT VF-S15 series ® option unit Function Manual CCL003Z NOTICE 1. Read this manual before installing or operating. Keep this instruction manual on hand of the end user, and make use of this manual in maintenance and inspection. 2. All information contained i

  • Toshiba TOSVERT VF-S15 series, E658130 - 25 - Address Signal Description RWwn+10 Instruction code 2 Set the command code for actions such as operation mode switching, parameter read, write, error reference, error clear, etc. The command will be executed by turning (RynF) on after the register setting is completed. When the command execution is completed, (RXnF) turns on. RWwn+11 Write data 2 Set data specified by the above-mentioned command code 2 (if necessary). If no data needs to be written, the value shall be zero. (RynF) is turned on after setting the above-mentioned command code and this register.

  • Toshiba TOSVERT VF-S15 series, E658130 - 6 - 3. Names and functions The drawing below shows names and functions of main parts. 3.1. Outline LED indicator (See 4.5) Release tab CC-Link Connector DA DB DG SLD FG Connector to the inverter

Related Products and Documents (Computer Accessories):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Ryobi RP4020 Operator's manual ryobi/rp4020-F3O.pdf 04 Jul 2022 40 9.52 Mb
2 NETGEAR FA311 - 10/100Mbps PCI Ethernet Interface Card Getting started netgear/fa311-10-100mbps-pci-ethernet-interface-card-2YZ.pdf 08 Nov 2023 20
3 Oki OF5400 Référence rapide oki/of5400-758.pdf 16 Sep 2022 20
4 Sanyo EM-S8588V Instruction manual sanyo/em-s8588v-DHO.pdf 07 Nov 2022 20 4.85 Mb
5 Nuvoton NuMicro Family Technical reference manual nuvoton/numicro-family-6Z1.pdf 28 Aug 2023 475
6 Yaesu VX-7R Service manual yaesu/vx-7r-5P1.pdf 16 Jan 2024 58 11.63 Mb

Similar Resources:

  • Compaq

    RAID Array 3000 Controller Shelf

    (112 pages)
    Compaq Confidential – Need to Know RequiredWriter: Bob Young Project: RAID Array 3000 Controller Shelf Hardware User's Guide Comments: Part Number: EK-SMCPQ-UG. D01 File Name: a-frnt.doc Last Saved On: 12/7/00 12:19 PMCompaq StorageWorks™RAID Array 3000 Controller ShelfHardwareUser’s GuideFourth Edition (January 2001)Part Number EK-SMCPQ-UG. D …
  • Tripp Lite

    NB1150BKTAB

    (2 pages)
    Tripp Lite1111 West 35th StreetChicago, IL 60609 USATelephone: +(773) 869 1234E-mail: [email protected] #: NB1150BKTABUniversal Tablet PC Case HighlightsThree levels of security keep your tablet from falling outHeavy-duty, custom metal hardware and reinforced nylon stitching helpprevent damage and wearAdjustable top flap stays conveniently out of …
  • Sony

    CDL1100

    (54 pages)
    1SUPPLEMENT-2File this supplement with the service manual.SUBJECT :1. ADDITION CDL1100-40 SERIES(ENG-99001)CDL1100SERVICE MANUALFor Technical ServiceThe 40 series has been added to the CDL1100. Use this manual together with the service manual already distributed (SUPPLEMENT-1).MODEL IDENTIFICATION— SPECIFICATION LABEL —SONY MODEL NO CDL1100-CD-ROM …
  • HP

    xw3400

    (2 pages)
    ﺔﻠﺴﻠﺴﻟ ﺔﻌﻳﺮﺴﻟا ﺔﻴﻌﺟﺮﻤﻟا ﺔﻗﺎﻄﺒﻟاHP xw Workstation ﺔآﺮﺷ ﺪﻬﻌﺘﺗHewlett-Packardﺎﻨﺗﺎﺠﺘﻨﻤﺑ صﺎﺨﻟا ﻲﺌﻴﺒﻟا ﺮﻴﺛﺄﺘﻟا ﺾﻔﺨﺑ . ﻦﻣ ءﺰﺠآ ﻚﻟذو ،ﺔﻃﻮﻐﻀﻤﻟا صاﺮﻗﻷاو ،ﺖﺑﺎﺜﻟا صاﺮﻗﻷا ك� …
  • Conrad

    Akasa

    (2 pages)
    Diese Bedienungsanleitung ist eine Publikation der Conrad Electronic SE,Klaus-Conrad- Straße 1, D-92240 Hirschau.Diese Bedienungsanleitung entspricht dem technischen Stand bei Drucklegung.Änderungen in Technik und Ausstattung vorbehalten.© 2009 by Conrad Electronic SE.*02_02/09_01-HWAkasa 18 cm LED PC FanVersion 02/09Item no. 87 15 35 Intended …
  • Intermec

    CK71

    (2 pages)
    Mobilcomputer-KurzanleitungGuía de comienzo rápido para la computadora móvilGuide de démarrage rapide de l’ordinateur mobilePanduan Memulai Cepat Komputer Layapモバイルコンピュータクイックスタートガイド모바일 컴퓨터 빠른 시작 안내서Manual de Consulta Rápida do Computador MóvelÊðàòêîå ðóêîâîäñòâî Í� …

Comments, Questions and Opinions: