EC Printer EC80320 Operation & User’s Manual

Text of EC Printer EC80320 User Guide:

• EC Printer EC80320, EC-80320 User’s Manual - 18 - 12) Return to “Properties”, make sure the network port is selected, click “Apply”, and then click “Close”. Thus, printer’s network port setting is finished.

• EC Printer EC80320, EC-80320 User’s Manual - 10 - Button description: Exit—Exit from the software Search—Search printers in the same LAN Assign IP—Modify the IP address and other settings for the specified printer. 2. Search printer Click “Search” button in the main interface, the dialog box appearing will begin searching automatically and show appearance, listing a printer in the main interface if found. The time is counting down in the progress bar (10s in total) and the search will finish as soon as the time is over. When going on searching, press “search” button again.

• EC Printer EC80320, EC-80320 User’s Manual - 17 - 9) Return to “Additional Port Information Required”, click “Next”. 10) Come out a window of “Completing the Add Standard TCP/IP Printer Port Wizard”, click “Finish”. 11) Return to “Printer Ports”, click “Close

• EC Printer EC80320, EC-80320 User’s Manual - 25 - Electricity: 2.5 A Power consumption operation: 40 W; max: 180 W; standby: 2.9 W Note: Only when the product doesn’t connect any power supply, can it consume zero energy. MCBF: 52 million lines Reliability Lifespan of cutter: ≥1 million cut Safety criterion GB 4943-2001 EMI Class B Star of energy resourceV1.1 Accord Authentication CCC authentication Specified function Online parameter settings Paper feed width 79.5 ± 0.5 mm Max paper thickness 0.065 ～ 0.15 mm Black mark Match 5.2 Interface Features The printer can connect to one drawer and one host. The interface connected to the host can be

• EC Printer EC80320, EC-80320 User’s Manual - 6 - 2.4 Connecting the Adapter 1. Make sure the printer’s power switch is turned off. Plug the adapter’s supply cable as shown below. Connect the adapter to the power cord. 2. Make sure the voltage of the electrical outlet matches that of the adapter. 3. Plug the adapter to the printer’s electrical outlet. 4. Plug the power thread one end to the adapter and the other to the AC outlet with ground wire. Note: 1. If the voltage of electric outlet isn’t within the scope marked in th

• EC-80320 User’s Manual - 28 - Table A-3: Drawer connector Pin assignments Pin number Signal Direction 1 Frame GND --- 2 Drawer kick-out drive signal OUT 3 Drawer Open/closed signal IN 4 24VDC OUT 5 Drawer kick-out drive signal OUT 6 Drawer kick-out Open/closed signal ground ≤1A/24V --- Drive electricity≤1A/24V Note: Make sure the drawer meets th

• EC Printer EC80320, EC-80320 User’s Manual - 30 - come out. Rotate the white plastic gear by hand in the direction of arrow to make the cutter return to the normal position which is shown as figure 6-1. Figure 6-1 Adjust the cutter by hand Auto-cutter

• EC Printer EC80320, EC-80320 User’s Manual - 22 - Chapter 4 Install and Replace the Roll Paper The printer can install the paper conveniently, which should be 80mm width. How to deal with the paper will be explained in details in this chapter 4.1 Paper Installed Steps 1. Push the cover open lever, open the cover. 2. Insert the paper roll as shown below（Be sure to note the correct direction that the paper comes off the roll）. 1. Don’t touch the thermal head after printing to avoid being burned. 2. Do

• EC Printer EC80320, EC-80320 User’s Manual - 13 - 5) Come out a window of “Add Port”, enter the IP address reported by the “Setting printer’s IP address” in the “Printer Name or IP Address” column. Take IP address “192.168.0.240” for example. “Port Name” is created automatically after finishing filling in IP address. 6) Come out a window of “Additional Port Information Required”, select “Custom” in the “Device Type”, then click “Settings”. 7) Come out a window of “Port Settings”. Affirm that “Port name” and “Printer name or IP

• EC Printer EC80320, EC-80320 User’s Manual - 12 - automatically. Please make sure there is a DHCP server in the network, or the printer can not receive an effective IP address. When to specify static address, uncheck “Use DHCP” and fill in “IP address”, “Subnet Mask” and “Default Gateway”. If there is no gateway in the network, fill 255.255.255.255 in the “Default gateway”. “IP address” and “Subnet Mask” should obey the assigning rules of local LAN (Ethernet), please enquire the administrator of networks which the printer connects to for more det

• EC Printer EC80320, EC-80320 User’s Manual - 27 - 5.2.3 USB Interface Full-speed USB interface of version 2.0. 5.2.4 Drawer Connector The drawer connector on the back of the printer uses the RJ-11 connector, which is shown below. Fig5-6 Drawer connector Fig 5-5 USB interface Fig5-3 TP820 connecting with 9-Pin PC Printer 9-Pin connector Host 9-Pin connector Printer 9PIN connector Host 25PIN connector Fig5-4 TP820 connecting with 25-Pin PC 1 6

• EC-80320 User’s Manual - 24 - Chapter 5 Features 5.1 General Specification Item Description Print method Direct thermal printing Print direction Line printing Paper width 72 mm Print speed 220mm/s（52line/s） Print head Lifespan: 100 Km Resolution 8 dot/mm, 576dot/line, 203DPI Character set ASCII: 13 international character sets Chinese: GB 18030 Code

• EC Printer EC80320, EC-80320 User’s Manual - 41 - GS * Define downloaded bit image Format: ASCII: GS * n1 n2 d1…dk Decimal: 29 42 n1 n2 d1…dk Hex: 1D 2A n1 n2 d1…dk Description: Define the downloaded bit image in the downloaded graphic area. n1=1～48，n2=1～255，n1×n2<1200,k=n1×n2×8。 d specifies the bit image data . n1×8 dots in the horizontal direction and n2×8 dots in the vertical direction. The downloaded bit image is available till printer is powered off or reset. The format of bit image is shown below.

• EC Printer EC80320, EC-80320 User’s Manual - 4 - 2. Connect the other end of the cable to the host. Tighten the connector screws. 3. This printer can carry out a network printing through connecting parallel interface to network print server, which you can use are PS-1206, SX-110 and SX-3100 which have been validated. 2.3.2 Connecting the Serial Interface Cable (Optional) 1. Make sure the Host and the printer are both turned off, connect the serial interface cable to the connector on the rear panel of the printer. Tighten the connector scre

• EC Printer EC80320, EC-80320 User’s Manual - 32 - DLE EOT n Real-time status transmission * Format: ASCII: DLE EOT n Decimal: 16 4 n Hex: 10 04 n Description: Transmit the selected printer status according the specified parameter n, 1<=n<=4; n=1: Transmit print status n=2: Transmit off-line status n=3: Transmit error status n=4: Transmit paper roll sensor status *Note: Only valid in serial interface. ESC BEL n1 n2 Beep for appointment Format: ASCII: ESC BEL n1 n2 n3

• EC Printer EC80320, EC-80320 User’s Manual - 38 - Selects the Chinese character mode according n as follows: FS & Set Chinese language mode Format: ASCII: FS & Decimal: 28 38 Hex: 1C 26 Description: In this mode, the code between 0x81 and 0xff are printed as Chinese character. FS - Turn Chinese character underline mode on /off Format:

• EC Printer EC80320, EC-80320 User’s Manual - 5 - 2.3.4 Connecting the Drawer Cable Turn off the printer and plug the drawer cable into the drawer connector on the back of the printer as shown in Fig2-5. Warning: Don’t connect a telephone line to the drawer connector; otherwise both the telephone line and the printer may be damaged. 2.3.5 Connecting the Ethernet Cable 1. Plug the crystal end of the Ethernet cable (RJ-45) into the printer's Ethernet connector as shown in Fig2-6. 2. Plug the other end of the Ethernet cable (flat) to the LAN’s entrance。 Fig2-5 Connecting the Drawer cable Fig2-4 Conn

• EC-80320 User’s Manual - 37 - ESC j Print and feed paper conversely Format: ASCII: ESC j n Decimal: 27 106 n Hex: 1B 6A n Description: Print the content in the buffer and feed paper n*vertical unit inch conversely. n=0～255. Horizontal or vertic

• EC Printer EC80320, EC-80320 User’s Manual - 43 - GS k Print bar code Format: ASCII: GS k m d1..dk NUL Decimal: 29 107 m d1..dk 0 Hex: 1D 6B m d1..dk 00 * ASCII: GS k m n d1..dn Decimal: 29 107 m n d1..dn Hex: 1D 6B m n d1..dn *when m>64 m Bar code type Amount of data The range of k character Character code 0 UPC-A Fixed 11<=k<=12 0~9 48<=d<=57 1 UPC-E Fixed 11<=k<=12 0~9 48<=d<=57 2 EAN13 Fixed 1

• EC-80320 User’s Manual - 21 - 3. Right click”EC80320”, select “Properties”. 4. Click “Printer settings” in the property page. 5. Check whether the selected port in the “Ports” is matched with the port connecting to the printer in practical. Return to “Device Property” page layout,

• EC Printer EC80320, EC-80320 User’s Manual - i - The Guide Be sure to have read the manual seriously before your operation. Neither EC PRINTER nor its affiliates shall be liable to the purchaser of this product or third parties for damages, losses, costs, or expenses incurred by purchaser or third parties as a result of: accident, misuse, or abuse of this product or unauthorized modifications, repairs, or alterations to this product, or failure to strictly comply with EC PRINTER’s operating and maintenance instruct

Related Products and Documents (Printer):

Comparable Devices:

Similar Resources:

• Canon iP4000 - PIXMA Photo Printer (33 pages) PIXMA iP4000SERVICEMANUALCanonCopyright 2004, Canon U.S.A. This technical publication is the proprietary and confidential information of Canon U.S.A. whichshall be retained for reference purposes by Authorized Service Facilities of Canon U.S.A. Its unauthorized use is prohibited. …

• Zebra P640 (40 pages) Programmer’s Manual For Zebra P640/P640i Photo ID Printers P/N: 980552-001 Zebra Card Solutions 6/15/2005 Page 1 of 40 www.zebracard.com …

• Lexmark N4050e - Print Server - USB (18 pages) www.lexmark.comAugust 2004N4050e Wireless Print ServerUser’s Guide for MacintoshLexmark and Lexmark with diamond design are trademarks of Lexmark International, Inc.,registered in the United States and/or other countries.© 2004 Lexmark International, Inc.All rights reserved.740 West New Circle RoadLexington, Kentucky 40550 …

• Sharp MX-C402SC (822 pages) COPIERPRINTERFACSIMILESCANNER / INTERNET FAXDOCUMENT FILINGTROUBLESHOOTINGBEFORE USING THE MACHINESYSTEM SETTINGSAbout Operation GuideMAKE A COPY PRINT A DOCUMENT SEND A FAXSCAN AN IMAGE /SEND AN INTERNET FAXSAVE A JOB ANDREUSE IT LATERMAINTAINTHE MACHINESearch based on what you want to doSearch based on what you want to doSearch using the table of contentsS …

• Agilent Technologies E4440A (80 pages) Getting Started GuidePSA Series Spectrum Analyzers This manual provides documentation for the following instruments:E4440A (3 Hz - 26.5 GHz)E4443A (3 Hz - 6.7 GHzE4445A (3 Hz - 13.2 GHz)E4446A (3 Hz - 44 GHz)E4448A (3 Hz - 50 GHz)Manufacturing Part Number: E4440-90242 Supersedes: E4440-90229 Printed in USAAugust 2004© Copyright 2001-2004 Agilent Technologi …

• HP Laserjet,Color Laserjet 4550 (18 pages) Copyright© 1998Hewlett-Packard Co.Printed in USAManual Part No.C4224-90901Printed on at least50%Total Recycled Fiber withat least 10% Post-ConsumerPaper*C4224-90901**C4224-90901*C4224-90901LaserJet1100HPQuickReferenceGuide …

Comments, Questions and Opinions: