Toshiba TOSVERT VF-S11 Instruction Manual

Text of Toshiba TOSVERT VF-S11 User Guide:

• E6581160 62 7 Title Communication No. Function Unit Minimum setting unit Panel/Commun ication Adjustment range Default setting User setting Reference E6581158 H 0710 Standard monitor display selection - - 0: Operation frequency (Hz/free unit) 1: Frequency command (Hz/free unit) 2: Output current (%/A) 3: Inverter rated current (A) 4: Inverter load factor (%) 5: Output pow

• Toshiba TOSVERT VF-S11, E6581160 13 2 Wire size (See Note 4) Voltage class Capacity of applicable motor (kW) Inverter model Power circuit (mm 2 ) (Note 1.) DC reactor (optional) (mm 2 ) Braking resistor/ Braking unit (optional) (mm 2 ) Earth cable (mm 2 ) 0.4 VFS11-4004PL 2.0 (2.0) 2.0 2.0 3.5 0.75 VFS11-4007PL 2.0 (2.0) 2.0 2.0 3.5 1.5 VFS11-4015PL 2.0 (2.0) 2.0 2.0 3.5 2.2 VFS11-4022PL 2.0 (2.0) 2.0 2.0 3.5 4.0 VFS11-4037PL 2.0 (2.0) 2.0 2.0 3.5 5.5 VFS11-4055PL 2.0 (2.0) 3.5 2.0 3.5 7.5 VFS11-4075PL 3.5 (2.0) 5.5 2.0 3.5 11 VFS11-4110PL 5.5 (2.0) 8.0 2.0 5.5 Three-phase 500V

• Toshiba TOSVERT VF-S11, E6581160 17 2 Q SINK (Negative) logic/SOURCE (Positive) logic (When an external power supply is used) The PLC terminal is used to connect to an external power supply or to insulate a terminal from other input or output terminals. As for input terminals, turn the SW1 slide switch to the PLC position. ＜Examples of connections when an external power supply is used＞ Sink (Negative) logic Inverter PLC F Programmable controller Common Output Input 24V DC Output F Output Input 24V DC Output OUT NO 24V DC Input Common I nverter Programmable controller Slide switch SW1:PLC Slide switch SW1:PLC PLC Common 24V DC OUTCommon NO Input Source (Positive) logic Q Selecting the functions of t

• Toshiba TOSVERT VF-S11, E6581160 45 6 Table 1 EMC standards Category Subcategory Product standards Test standard and level Radiation noise EN55011 Class A Group 1 Emission Transmission noise EN55011 Class A Group 1 Static discharge IEC61000-4-2 Radioactive radio-frequency magnetic contactor field IEC61000-4-3 First transient burst IEC61000-4-4 Lightning surge IEC61000-4-5 Radio-frequency induction/transmission interference IEC61000-4-6 Immunity Voltage dip/Interruption of power IEC 61800-3 IEC61000-4-11 Emission standards other than the above are applied to inverters when used in a commercial environment

• Toshiba TOSVERT VF-S11, E6581160 39 5 5.1.2 Display of detailed information on a past trip Details on a past trip (of trips 1 to 4) can be displayed, as shown in the table below, by pressing the key when the trip record is selected in the status monitor mode. Unlike the "Display of detailed trip information at the occurrence of a trip" in 5.2.2, details on a past trip can be displayed, even after the inverter is turned off or reset. Item displayed Key operated LED display Description Past trip 1 QE  ⇔ Past trip 1 (displayed alternat

• E6581160 12 2 2.2 Description of terminals 2.2.1 Power circuit terminals In case of the lug connector, cover the lug connector with insulated tube, or use the insulated lug connector. Screw size tightening torque M3.5 screw 0.9Nm 7.1lb y in M4 screw 1.3Nm 10.7lb y in M5 screw 2.5Nm 22.3lb y in M6 screw 4.5Nm 40.1lb y in Q Power circuit Terminal symbol Terminal function

• Toshiba TOSVERT VF-S11, Simplified manualIndustrial Inverter TOSVERT VF-S11 2 1 3 4 5 6 7 8 9 9 10 11 12 13 14 15 16 E6581160 Connection I Safety precautions Contents Read first Operations Basic VF-S11 operations Monitoring the operation status Measures to satisfy the standards Table of parameters and data Specifications Before making a service call Measures to satisfy the standards Peripheral devices Table of parameters and data Specifications Before making a service call - Trip information and remedies Inspection and maintenance Warranty Disposal

• Toshiba TOSVERT VF-S11, E6581160 79 9 [Alarm information] Each message in the table is displayed to give a warning but does not cause the inverter to trip. Error code Problem Possible causes Remedies QHH ST terminal OFF • The ST-CC circuit is opened. • Close the ST-CC circuit. OQHH Undervoltage in main circuit • The supply voltage between R, S and T is under voltage. • Measure the main circuit supply voltage. If the voltage is at a normal level, the inverter requires repairing. TVT[ Retry in process • The inverter is n

• Toshiba TOSVERT VF-S11, E6581160 57 7 Title Communication No. Function Unit Minimum setting unit Panel/Commun ication Adjustment range Default setting User setting Reference E6581158 0: Supply voltage uncorrected, output voltage limited 1: Supply voltage corrected, output voltage limited 2: Supply voltage uncorrected, output voltage unlimited H 0307 Supply voltage correction (limitation of output voltage) -- 3: Supply voltage corrected, output voltage unlimited 2 (WP, WN) 3 (AN) 6.13.6 H 0308 Dynamic braking resistance Ω 0.1/0.1 1.0-1000 * 1 6.13.4 H 0309 Dynamic braking resistor capacity kW 0.01/0.01 0.01-30.00 * 1 6.13.4 H

• Toshiba TOSVERT VF-S11, E6581160 66 7 Q Table of input terminal functions 2 Function No. Code Function Action 34 F+SS3+AD2 Combination of forward run, preset-speed command 3 and acceleration/deceleration 2 ON: Simultaneous input from F, SS3 and AD2 35 R+SS3+AD2 Combination of reverse run, preset-speed command 3 and acceleration/deceleration 2 ON: Simultaneous input from R, SS3 and AD2 36 F+SS4+AD2 Combination of forward run, preset-speed command 4 and acceleration/deceleration 2 ON: Simultaneous input from F, SS4 and AD2 37 R+SS4+AD2 Combination of

• Toshiba TOSVERT VF-S11, E6581160 58 7 • Torque boost parameters 1 Title Communication No. Function Unit Minimum setting unit Panel/Commun ication Adjustment range Default setting User setting Reference E6581158 0: Auto-tuning disabled 1: Initialization of H (reset to 0) H 0400 Auto-tuning - - 2: Auto-tuning enabled (after execution: 0) 0 H 0401 Slip frequency gain % 1/1 0-150 50 H 0402 Automatic torque boost value % 0.1/0.1 0.0-30.0 * 1 H 0415 Motor rated current A 0.1/0.1 0.1-100.0 * 1 H 0416 Motor no-load current % 1/1 10-90 * 1 H 0417 Motor rated speed min-1 1/1 100-32000 1410(WP) 1710 (WN, AN) H 0418 Speed control response coefficient -

• Toshiba TOSVERT VF-S11, E6581160 43 5 Note 9: The cumulative operation time increments only when the machine is in operation. Note 10: At the occurrence of a trip, maximum values are not always recorded and displayed for reasons of detecting time. Note 11: If there is no trip record, nerr is displayed. ✩ ✩✩ ✩ Of the items displayed on the monitor, the reference values of items expressed in percent are listed below. • Load current: The current monitored is displayed. The reference value (100% value) is the rated output

• Toshiba TOSVERT VF-S11, E6581160 59 7 • Acceleration/deceleration time parameters Title Communication No. Function Unit Minimum setting unit Panel/Commun ication Adjustment range Default setting User setting Reference E6581158 H 0500 Acceleration time 2 s 0.1/0.1 0.0-3200 10.0 H 0501 Deceleration time 2 s 0.1/0.1 0.0-3200 10.0 H 0502 Acceleration/decel eration 1 pattern -- 0 H 0503 Acceleration/decel eration 2 pattern -- 0: Linear 1: S-pattern 1 2: S-pattern 2 0 H 0504 Acceleration/decel eration selection (1, 2 , 3) - - 1: Acceleration/deceleration 1 2: Acceleration/deceleration 2 3: Acceleration/deceleration 3 1 H 0505 Acceler

• Toshiba TOSVERT VF-S11, E6581160 69 7 Q Table of output terminal functions 3 Function No. Code Function Action 35 FCVIBN Inversion of frequency VIB selection Inversion of FCVIB 36 FLR Fault signal (put out also at the time of a retry) ON: When inverter trips or retries OFF: When inverter does not trip or retry 37 FLRN Inversion of failure signal (put out also at the time of a retry) Inversion of FLR 38 OUT0 Specified data output 1 ON: Specified data from remote control FA50: BIT0= 1 OFF: Specified data from remote control FA50: BIT0= 0 39 OUT0N Inversion of specified data output 1

• E6581160 74 8 Q Outline drawing 130 R2.5 15 121.5(Installation dimension) 60 f 5 D 8 64.5 50 68 M5 4-M4 EMC plate VF-S11 72 (Installation dimension) 130 R2.5 13 121.5(Installation dimension) 93(Installation dimension) f 5 D 8 64.5 50 95 M5 4-M4 EMC plate VF-S11 105 Fig.A Fig.B 170 2-R2.5 14 65 157(Installation dimension) 126(Installation dimension) 2

• Toshiba TOSVERT VF-S11, E6581160 42 5 (Continued) Item displayed Key operated LED display Communic ation No. Description Parts replacement alarm information m }}}i FE79 The ON/OFF status of each of the cooling fan, circuit board capacitor, main circuit capacitor of parts replacement alarm or cumulative operation time are displayed in bits. ON:  OFF: _ Cumulative operation time V FE14 The cumulative operation time is displayed. (0.01=1 hour, 1.00=100 hours) Default display mode QR The cause of the trip is displayed. Note 1: Items displayed c

• Toshiba TOSVERT VF-S11, E6581160 28 4 4.1 Flow of status monitor mode Setting monitor mode Standard monitor mode Display mode Hz PRG MON RUN MODE MODE MODE 10 kinds of data Data of 4 times. ENT ENT ENT ENT Past trip record detained monitor mode Note: To return to the original display mode, press the MODE key. Status monitor mode 28 kinds of data Of the 10 kinds of data predetermined, any data can be read out 4 times. Data collected at the time of occurrence of a trip is retained. Up to 28 kinds of data can be read out. During normal operation: Data is displayed in real time. (See Section 5.

• Toshiba TOSVERT VF-S11, E6581160 20 3 3.1.1 How to start and stop [Example of a EOQF setting procedure] Key operated LED display Operation  Displays the operation frequency (operation stopped). (When standard monitor display selection H= [Operation frequency]) CWJ Displays the first basic parameter [History (CWJ)]. EOQF Press either the or key to select “EOQF”.  Press ENTER key to display the parameter setting. (Default setting:).  Change the parameter to  (terminal board) by pressing the key. ⇔EOQF Press the ENTER key to save the changed parameter. EOQF and the parameter set value are displayed alternately. (1) Start and stop using the oper

• Toshiba TOSVERT VF-S11, E6581160 9 1 1.2 Contents of the product Explanation of the name plate label. Always shut power off first then check the ratings label of inverter held in a cabinet. Type Form VFS11S - 2007PLE- WN -A22 Model name TOSVERT VF-S11series Number of power phases S: sin g le- p hase None: three- p hase Applicable motor capacity 002 : 0.2kW 004 : 0.4kW 005 : 0.55kW 007 : 0.75kW 015 : 1.5kW 022 : 2.2kW 037 : 3.7kW 055 : 5.5kW 075 : 7.5kW 110 : 11kW 150 : 15kW Additional functions I None: No filter inside M: Built-in basi

• E6581160 15 2 Terminal symbol Input/output Function Electrical specifications Inverter internal circuits VIB Input Multifunction programmable analog input. Standard default setting: 0~10Vdc input and 0~60Hz (0~50Hz) frequency By changing parameter setting, this terminal can also be used as a multifunction programmable contact input terminal. When using the sink logic, be

• Toshiba TOSVERT VF-S11, E6581160 65 7 Q Table of input terminal functions 1 Function No. Code Function Action 0 - No function is assigned Disabled 1 ST Standby terminal ON: Ready for operation OFF: Coast stop (gate off) 2 F Forward run command ON: Forward run OFF: Slowdown stop 3 R Reverse run command ON: Reverse run OFF: Slowdown stop 4 JOG Jog run mode ON: Jog run, OFF: Jog run canceled 5 AD2 Acceleration/deceleration 2 pattern selection ON: Acceleration/deceleration 2 OFF: Acceleration/deceleration 1 or 3 6 SS1 Preset-speed command 1 7 SS2 Preset-speed command 2 8 SS3 Preset-speed command 3 9 SS4 Preset-speed command 4 Selection of 15-speed with S

• Toshiba TOSVERT VF-S11, E6581160 63 7 Title Communication No. Function Unit Minimum setting unit Panel/Commun ication Adjustment range Default setting User setting Reference E6581158 H 0811 Communication command point 1 setting % 1/1 0-100 0 H 0812 Communication command point 1 frequency Hz 0.1/0.01 0.0-500.0 0.0 H 0813 Communication command point 2 setting % 1/1 0-100 100 H 0814 Communication command point 2 frequency Hz 0.1/0.01 0.0-500.0 50.0 (WP) 60.0 (WN, AN) 6.5.2 6.22.1 H 0829 Selection of communication protocol - - 0: Toshiba inverter protocol 1: Modbus RTU protocol 0 H 0870 Block write data

• E6581160 26 3 Operation frequency setting, running and stopping using external signals. (1) Wiring (2) Parameter setting Title Function Programmed value EOQF Command mode selection 0 HOQF Frequency setting mode selection 1or2 (3) Operation Run/stop: ON/OFF input to F-CC, R-CC. (Set SW1 to Sink logic) Frequency setting: VIA and VIB: 0-10Vdc (External potentiometer) VIA: Input 4-20mAdc. Note) Use

More Instructions:

	Toshiba TOSVERT VF-S11 Instruction manual 27-02-2023 269	DOWNLOAD
	Toshiba TOSVERT VF-S11 Instruction manual 11-01-2023 256	DOWNLOAD
	Toshiba TOSVERT VF-S11 Specifications 06-11-2022 12	DOWNLOAD
	Toshiba TOSVERT VF-S11 Instruction manual 26-11-2023 68	DOWNLOAD

Related Products and Documents (Inverter):

Comparable Devices:

Similar Resources:

• leadsun AE3 Series (8 pages) Made in ChinaAddress: 1920 S. Archibald Ave. Suite I, Ontario, CA 91761Phone: 909.476.0900Fax: 909.466.0130Email: [email protected] Australia Pty Ltd LEADSUN Global LtdSolar LightUser ManualAE3 SERIESLEADSUN INC.Address: 42 Greens Road, Dandenong South, Victoria 3175Phone: +61 1300 281 005 Fax: +61 3 8610 0393 Email: [email protected]: …

• Viessmann Vitosol-F (24 pages) Installation instructionsfor contractorsVIESMANNVitosol-F/-FMType SVKA, SVKGFlat-plate collector for pitched roofs, roof integrationVITOSOL-F/-FM5698 362 GB 1/2016Dispose after installation. …

• Mastervolt Whisper 6 (40 pages) USERS MANUAL U.S.A EDITION WHISPER 6 / 8 / 11 - 3600 RPM - Marine diesel generating set 120/240V / 60Hz Digital Diesel Control MASTERVOLT Snijdersbergweg 93, 1105 AN Amsterdam The Netherlands Tel.: +31-20-3422100 Fax.: +31-20-6971006 www.mastervolt.com V8. July 2009 Art.nr. 50200354 …

• Salicru ControlVIT CV10 series (5 pages)  Quick Start Guide of CV10- ControlVIT Series 1 / 5 EL086A01 ❶ Safety precautions  Do not refit the inverter unauthorizedly; otherwise fire, electric shock or other injury may occur.  Please install the inverter on fire-retardant material and keep the inverter away from combustible materials.  Connect the braking optional parts according …

• Solax X1-Hybrid Series (2 pages) IPV ConnectionGrid and Off-grid ConnectionTool Preparation Quick Installation Guide *18AWG European terminals*3X1-Hybrid G4series inverter.BracketWaterproof cover*1 PV terminal (positive*2 , negative*2 )Waterproof connector with RJ45*4/3(Meter/DRM)RJ45 terminals*1 10AWG European terminals*2(Expansion bolt ,Gas …

• GENERGY VULCANO (124 pages) MOTOSOLDADURAS GASOLINA GENERGY GASOLINE WELDING GENERATOR GENERGY SOLDADOR GERADOR GASOLINA GENERGY INSTRUCCIONES DE USO POR FAVOR, LEA ESTE MANUAL CON ATENCIÓN ANTES DE UTILIZAR LA MÁQUINA INSTRUCTIONS …

Comments, Questions and Opinions: