Toshiba TOSLINE-S20LP Instruction Manual

Text of Toshiba TOSLINE-S20LP User Guide:

• Toshiba TOSLINE-S20LP,  21  6 F 3 B 0 3 5 6 3.3 Settings on S-LS (1) Start-up the S-LS Connect the S-LS (personal computer) and the S20LP-station by the loader cable. Start-up the S-LS for Windows95. (2) Turn the T2N/T3H to HALT (3) Confirm the S20LP-station status Confirm the status of the connected S20LP-station is "STANDBY" by right and upper side. It is displayed on the S-LS screen as below.

• Toshiba TOSLINE-S20LP,  35  6 F 3 B 0 3 5 6 5.4 RAS information monitored in T2N/T3H RAS information of the S20LP system is reflected in the special registers (SW) of T2N/T3H. This information can be referred in the T2N/T3H’s user program. SW110 CH1 station status (1 word) SW111 CH2 station status (only T3H) (1 word) SW112 CH1 online map (4 words) SW116 CH2 online map (only T3H) (4 words) SW120 CH1 standby map (4 words) SW124 CH2 standby map (only T3H) (4 words) SW128 Loop map (only T2N) (32 words)

• Toshiba TOSLINE-S20LP,  15  6 F 3 B 0 3 5 6 (2) Network assignment a) Set "LINK" for the Blocks to be assigned. 0 Receive Block 1 W000-063 LINK Block 2 100 W064-127 LINK Send Block 3 W128-191 LINK Block 4 230 W192-255 LINK Block 5 W256-319 Receive 2047 Block 32 W1983-2047 LINK <Setting example> S20LP-station common memory T2N/T3H W registers Network assignment . . .

• Toshiba TOSLINE-S20LP,  24  6 F 3 B 0 3 5 6 Write the settings into the S20LP-station. Press "OK" button. When the settings are correctly written into the S20LP-station's EEPROM, it is displayed on the screen as below.

• Toshiba TOSLINE-S20LP,  57  6 F 3 B 0 3 5 6 6) Response time limit Designates a time used to limit the response time from the remote station in 0.1 second units. F E 0 A+7 (c) Status (See 7.3 (5) for details on bits C, D, E, and F.) F E D C B A 9 8 7 6 5 4 3 2 1 0 B 0 0 0 0 TermSTS B+1 Detailed information (Only valid when TermSTS = 0BH.) (d) Important items • The command number (0000H) is the same as the "Data Write". • A transfer size error (TermSTS = 09H) occurs if the transferred register data length exceeds the range 1 to 128 words

• Toshiba TOSLINE-S20LP,  6  6 F 3 B 0 3 5 6 SN325 STN ONL SCAN ACC LOOP TX1 TX2 RESET STNH STNL OTR1 OTR2 LOADER Status LEDs Reset switch Station number setting switches Transmission cable connectors LOADER port SN325

• Toshiba TOSLINE-S20LP,  65  6 F 3 B 0 3 5 6 If the T-PDS is connected to the T2N/T3H on the second layer through the bridge station (T3H only), set the T-PDS's connection method as follow. -LP S20T2N -LP S20T3H -LP S20T3H S20LP S20LP STN #3STN #2 STN #1 T-PDS STN #1 -LP S20 STN #3STN #2 -LP S20T2N -LP S20T2N <T-PDS Setup options screen> (Note 1) The Layer 1 Station No. specifies the bridge station and the Layer 2 Station No. specifies the target station on the second layer. (Note 2) Only T3H is available for the bridge station. (Note 3) The Parity is fixed as even.

• Toshiba TOSLINE-S20LP,  19  6 F 3 B 0 3 5 6 c) If two S20LP-stations are mounted on the T3H and multi layers Scan transmission function is used, use the "GLOBAL" setting. (GLOBAL is invalid for T2N) <Setting example 3> Block 1 Send 1 LINK Receive LINK Block 2 LINK Block 3 LINK Send 1 Block 4 LINK Block 5 Receive LINK Block 6 GLOBAL Block 7 GLOBAL Send 2 Block 8 GLOBAL Block 9 Send 2 GLOBAL Block 10 Receive Receive Block 32 LINK CH1 Network assignment CH1 S20LP-station common memory CH2 S20LP-station common memory CH2 Network assignment T3H W registers . . . .

•  53  6 F 3 B 0 3 5 6 6) Response time limit Designates a time used to limit the response time from the remote station in 0.1 second units. F E 0 A+7 This code indicates the type of register code in which the local or remote station transmission source data is stored. See “T-series Instruction Set (Ladder, SFC)” (UM-TS03***-E004). RID Meaning RID Meaning 000

•  14  6 F 3 B 0 3 5 6 3. Setting for data linkage 3.1 Station number setting Each station should have unique station number. If a station number is duplicated, the S20LP network cannot be established. Allowable station number is 1 to 64. To set the station number, two rotary switches (STNH and STNL) are provided on each station. STNH is for 10's digit setting, an

•  43  6 F 3 B 0 3 5 6 (4) Parameter and construction Source parameter Transfer size and status Destination parameter A Bank/CH Type B Transfer size C Bank/CH Type A+1 Leading address C+1 Leading address Transfer parameter table Transfer object Type Leading address Bank/CH Transfer size Status flag T2N 0 to 127 1 to 128 XW/YW register T3H 00H 0 to 511 0 1 to 256 None W r

• Toshiba TOSLINE-S20LP,  54  6 F 3 B 0 3 5 6 *3 The T and C registers hold data that has flags attached. Supplement: The transfer data length has a maximum of 323 words when data is transferred over the Ethernet. For the T registers, it is not possible to designate a range that spans both the basic T registers (0 to 511) and the expansion T registers (512 to 999). The T3H has the expansion T register, but the T2N does not have. (c) Status (See 7.3 (5) for details on bits C, D, E, and F.) F E D C B A 9 8 7 6 5 4 3 2 1 0 B 0 0 0 0 TermSTS B+1 Detailed information (Only valid when TermSTS = 0BH.) (d) Important items • The command num

• Toshiba TOSLINE-S20LP,  5  6 F 3 B 0 3 5 6 1.2 Station hardware • Overview PU245N RUN FLT BAT ERUN ET/R EACC SRUN SONL SACC STNH STNL LINK PROG OTR1 OTR2 10BASE-T Status LEDs for Ethernet Port Status LEDs for S20LP Port DIP switches for CPU For S20LP Port Station number setting switches Transmission cable connectors LOADER port For Ethernet Port T2N include of S20LP Port

• Toshiba TOSLINE-S20LP,  49  6 F 3 B 0 3 5 6 (5) Status (B) The status during the execution of a SEND or RECV instruction and after that instruction terminates is stored in the register shown at B. When TermSTS = 0BH, the detailed information (S20LP-station error information) will be loaded into the registers indicated at location B + 1. The following figure shows the structure of the status information (register B) and following tables (TermSTS (Part1 and Part2) and detailed information) show the detailed information (register B +1). B Status B+1 Detailed information F E D C B A 9 8 7 6 5 4 3 2 1 0 B 0 TermSTS (Note 6) The user program must set bits C

• Toshiba TOSLINE-S20LP,  64  6 F 3 B 0 3 5 6 A.2 T-PDS remote programming The T-PDS can be connected through the Loader port on the S-20LP-station, as well as the Programmer port on the T2N/T3H CPU module. By using this function, remote programming/monitoring through S20LP network is available. (Note 1) T2N must be sellected P/S "ON" with DIP switch 1. (Note 2) When DIP switch 1 is ON/OFF, T2N is Loader port/Programmer port. -LP S20T2N -LP S20T3H -LP S20T3H S20LP STN #3STN #2 T-PDS STN #1 To use this function, T-PDS's connection method should be set as "Network". The scr

• Toshiba TOSLINE-S20LP,  51  6 F 3 B 0 3 5 6 Detailed Information (Send completion status) Error Code Description Normal complete 81H The remote station normally received message frame from local station. Busy 90H The remote station is standby. Timeout A0H The answer frame for the transmitted message frame no returned from remote station on time. Length error B0H Incorrect message frame length in remote station. Station mode error D0H The local station is Offline. Transmission prohibited state (local station) E0H The local station cannot transmit message in the message transmission prohibited state. Transmission prohibited state (remote station

• Toshiba TOSLINE-S20LP,  60  6 F 3 B 0 3 5 6 [00010 MOV RW090] [00000 MOV RW091] [00064 MOV RW092] R0520 [00004 MOV RW093] [01000 MOV RW094] R0520 R0090 ( ) /* PC Link preparation */ /* Number of executions, Operation on error occurrence, Transfer data length */ [00004 MOV RW095] [02000 MOV RW096] /* Transmission source register type, leading address */ /* Transfer destination register type, leading address */ [00004 MOV RW097] [03000 MOV RW098] /* Storage register type, leading address */ /* Data preparation */ R0090 R0091 R009F [00004 MOV D0901] [00900 MOV D0902

• Toshiba TOSLINE-S20LP,  23  6 F 3 B 0 3 5 6 Select the "Station Number" of the connected S20LP-station. Select the "Scan Transmission" and specify the "data send block(s)". The "data send block" is specified by entering the starting address (Send Starting Address 1/2) and the size (Number of Send Words 1/2). Up to two "data send blocks" can be specified. If "data send block 2" is not used, enter 0 both for Send Starting Address 2 and Number of Send Words 2. The maximum size of send words is Number of Send Words 1 and 2, total 1024 words.

• Toshiba TOSLINE-S20LP,  25  6 F 3 B 0 3 5 6 (5) Settings of station control information Open the "Setting Information", and push the "Station Control" by mouse. • Scan Transmission Enable/disable the Scan transmission. Select Enable to use the Scan transmission function. • Scan Access Scan data synchronization 1 word or 2 words. If 2W (2 words) is selected, data synchronization of double-word data (lower even and higher odd addresses) is achieved. In this case, 2W setting is needed both on the sender and receiver stations. Also, if 2W is selected, Send Start Address and Send Word Number must be even number. • Message Transmiss

• Toshiba TOSLINE-S20LP,  48  6 F 3 B 0 3 5 6 (Note 1) ERF is the S0051 special relay. See the T-series Instruction Set for information on ERF usage. (Note 2) For these instructions, instruction execution starts at the point the input changes state from off to on. (Note 3) Since these instructions span multiple scans, applications must hold the input in the on state until the output goes to the on state. (Note 4) After instruction execution terminates, it is possible to start execution again by applying a new input. (4) Transfer parameters (A) The data required for a request to the S20LP-station is set up in an area that starts in the register

Related Products and Documents (Network Cable):

Comparable Devices:

Similar Resources:

• Tripp Lite N201-020-BL (2 pages) Tripp Lite1111 West 35th StreetChicago, IL 60609 USATelephone: +(773) 869 1234E-mail: [email protected] #: N201-020-BL20-ft. Cat6 Gigabit Snagless Molded Patch Cable (RJ45 M/M) - Blue HighlightsMeets Category 6 cabling standardsMeets most current industry standards including IEEE 802.3ab, IEEE 802.5,ANSI/EIA/TIA 568, ISO/IEC 11801, and ETL (Categ …

• Tripp Lite N304-06M (2 pages) Tripp Lite1111 West 35th StreetChicago, IL 60609 USATelephone: +(773) 869 1234E-mail: [email protected] #: N304-06M6M (20-ft.) Duplex MMF 62.5/125 Patch Cable (SC/ST) HighlightsPremium PVC 62.5/125µm multimode patch cablesAttenuation loss meets or exceeds the latest industry standardsDescriptionTripp Lite's 6-meter multimode duplex fiber op …

• Clas Ohlson CBL-207 (24 pages) S U O M IN O R S KS V E N S K AE N G L I S H38-2433Network Cable USBModel: CBL-207 …

• Tripp Lite S502-01M (2 pages) Tripp Lite1111 West 35th StreetChicago, IL 60609 USATelephone: +(773) 869 1234E-mail: [email protected] #: S502-01M1M Internal SAS Cable - 4-in-1 32Pin (SFF-8484) to 4 x 7pin Cable Highlights32-pin SFF-8484 to 4 x 7-pin internal SAS cableSupports data rates of up to 3.0GbsStraight backshell configuration1 meter in lengthDescriptionTripp Lite&apos …

• Tripp Lite P450-000 (2 pages) Tripp Lite1111 West 35th StreetChicago, IL 60609 USATelephone: +(773) 869 1234E-mail: [email protected] #: P450-0002 piece DB9 Female to RJ45 Null Modem Adapter Cable Kit Highlights2pc DB9F to RJ45 Null Modem Adapter KitUses readily available Cat5 Patch CablesNull Modem Serial Connections up to 100ft Description With Tripp Lite's P450-000 Nu …

• Tripp Lite N318-06M (2 pages) Tripp Lite1111 West 35th StreetChicago, IL 60609 USATelephone: +(773) 869 1234E-mail: [email protected] #: N318-06M6M (20-ft.) Duplex MMF 62.5/125 Patch Cable (LC/ST) HighlightsManufactured from 62.5/125 duplex (zipcord) fiberIdeal for LAN applicationsGlass fiber compositionDescriptionTripp Lite's 6-meter multimode duplex fiber optic ST/LC p …

Comments, Questions and Opinions: