Toshiba XM-7002B Specification

Text of Toshiba XM-7002B User Guide:

• Toshiba XM-7002B, 18/27 XM-7002B Rev.1.0 6.3. Connector Figure 13 shows the connector and Figure 14 shows the interface pin assignments Use Japan Aviation Electronics Industry Limited KX15-50KLD L or equivalent. Conformable connector is Japan Aviation Electronics Industry Limited KX14-50K*D or equivalent. (Note: * is No.2.85,5, 8, 11. The recommendation is No.5) CD-ROM DRIVE REAR VIEW TOP BOTTOM 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 Figure 13 Connector pin assignments Connector contact 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 3

• Toshiba XM-7002B, 15/27 XM-7002B Rev.1.0 6.2.2. Timing of Host Interface (PIO) Figure 10 shows the Host Interface Timings. Address valid*1 DIOR-/DIOW- Write data valid*2 Read data valid*2 IOCS16- IORDY t4 t6 t7 t9 tA t8 t0 t2 t1 t5 t3 tB tRD t2i t6Z *1:Device Address consists of signals CS0-, CS1-, and DA2-0 *2:Data consists of DD0-15 (16-bit) or DD0-7 (8-bit) PIO Mode 4 timing parameters min(ns) max(ns) Min Time (ns) Max Time (ns) t0 Cycle time 120 t1 Address valid to DIOR-/DIOW-setup 25 t2 DIOR-/DIOW- pulse wide 70 t2i DIOR-/DIOW- recovery time 25 t3 DIOW- data setup 20 t4 DIOW- data hold 10 t5 DIOR- data setup 20 t6 DIOR- data hold 5 t6Z DIOR- data tristate 30 t7 Addr val

• Toshiba XM-7002B, 16/27 XM-7002B Rev.1.0 6.2.3.Timing of Host Interface (DMA Multi) Figure 11 shows the Host Interface DMA multi word Timings DMARQ DMACK-*1 DIOR/DIOW-*1 Read DD0-1 Write DD0-1 t0 tZ tI tJ tD tE tL tF tH tG tK *1: In all timing diagrams, the low line indicator negated, and the upper line indicators asserted. Multi word DMA Mode 2 timing parameters min (ns) max (ns) Min time (ns) Max time (ns) t0 Cycle time 120 tC DMACK to DMREQ delay --- tD DIOR-/DIOW- 16-bit 70 tE DIOR- data access 50 tF DIOR- data hold 5 tZ DMACK- to tristate 25 tG DIOR/DIOW- data setup 20 tH DIOW- data hold 10 tI DMACK to DIOR-/DIOW-

• Toshiba XM-7002B, 11/27 XM-7002B Rev.1.0 MO DRIVER AUDIO FILTER DATA CONTROL IDE/ATAPI INTERFACE CONTROL CD-ROM SYNC DETECT DE-SCRAMBLE HEADER DETECT ERROR CORRECTION RAM EFM DE-MOD VCO CONTROL VCO 17/34 MHz SERVO CONTROL AUDIO EFFECT DAC ERROR CORRECTION MASTER CLOCK GEN. ACCESS CONTROL PERIPHERAL INTERFACE TIMING CONTROL TIMER INT.CONTROL MICRO PROCESSOR Z80 Compatible Feed-Mo FOCUS TRACKING D-RAM 128 kB DISC MOTOR POSITION DETECTOR FEED MOTOR MUTING GND DRAWER RELEASE DETECTOR EJECT SW BUSY LED PUH RF AMP SERVO AMP 33.86 MHz 50 MHz SOLENOID

• Toshiba XM-7002B, XM-7002B Rev.1.0 Contents 1. Introduction ----------------------------------------------------------------------------------------------------------------------------- 1 2. Features --------------------------------------------------------------------------------------------------------------------------------- 2 3. Specifications ------------------------------------------------------------------------------------------------------------------------- 3 3.1. Performance -----------------------------------------------------------------------------------

• 4/27 XM-7002B Rev.1.0 (5) Access Time (Typ.) Average Random Access Time*3 95 ms (Max.24X) 110 ms (10X) Average Random Seek Time*4 90 ms (Max.24X) 100 ms (10X) Average Full Stroke Access Time*5 180 ms (Max.24X) 200 ms (10X) *1: All CD formats, except CD Red book (audio), require additional application specific software and/or hardware. The CD-ROM drive referenced in the specification i

• Toshiba XM-7002B, 27/27 XM-7002B Rev.1.0 EU-Declaration of Conformity ED-Directive Related Standard Issude Level/Test condition EMC-emission: EMC-immunity Product/Options Model Related EU-Directive 89/336/EEC CD-ROM Drive XM-7002B X Manufactuer(s) Location Address Page: Revision: EN55022+A2 1994+1997 Class B EN50081-1 1992 Residential, commercial & light industry EN5524 1997 Information tecnology equipment-Immunity characteristics-Limits and methods measurement IEN61000-4-2+A1 1995+1998 CD:

• Toshiba XM-7002B, 3/27 XM-7002B Rev.1.0 3. Specifications 3.1. Performance (1) Applicable Disc Format*1 Red-Book, Yellow-Book, CD-ROM XA, CD-IBridge ( Photo-CD, Video CD ), CD-I, CD-I Ready, CD-G and Multisession ( Photo-CD,CD EXTRA ), CD-RW, CD-R, CD-TEXT (2) Data Capacity(Yellow-Book) User Data/Block 2,048 Byte/block(Mode 1) 2,336 Byte/block(Mode 2 Form 2) (3) Rotational Speed*2 Approx. 2,180 rpm (4.4-10X) Approx. 5,200 rpm (10.3-24X) (4) Transfer Rate (1 KByte=2 10 Byte=1,024 Bytes, 1 Mbyte=2 20 Byte=1,048,576 Bytes) Block Transfer Rate Approx. 330-750 Block/s (4.4-10X) Approx. 772-1,800 Block/s (10.3-24X) Data Transfer Rate (Yell

• Toshiba XM-7002B, 24/27 XM-7002B Rev.1.0 11.Maintenance 11.1. Disc Try to avoid touching the read area (underside) of the disc as dirt and smears will degrade the disc accessing speed. If the disc is dirty, wipe it with a soft cloth. 11.2. Optical Pickup A dirty Optical Pickup will also degrade the access time. When the Pickup is dirty, gently wipe the objective lens of the Pickup. 12.Emergency Eject Execute following procedure only in the case of emergency (drawer will not eject although pressing Eject button). (1) Turn the CD-ROM drive supplying power off, and then keep the this condition for 1 minute. (2) Insert solid bar (like paper clip) into Emergency eject hole and push as shown in Fi

• Toshiba XM-7002B, 2/27 XM-7002B Rev.1.0 2. Features (1) Lightening by All Aluminum Cabinet Structure (180 g) (2) 12.7 mm Height (3) Support 12 cm/8 cm CD-ROM Disc Drive (4) Rotational speed can be controlled by command Max.24 (Ave.17X), Max.20X (Ave.14X), Max.16X (Ave.11X), Max.10X (Ave.7X) (5) 95 ms (target) Random Access Time (Max.24X) (6) Max.3,600 KBytes/s (Ave. 2,550 KBytes/s) Sustained Data Transfer Rate (7) 5 V Single Voltage Source (8) Support Multisession Disc ( Photo-CD, CD EXTRA), CD-R, CD-RW, CD-Text (9) Support Multimedia PC-3 Spec. (10) Support Windows

• 20/27 XM-7002B Rev.1.0 6.4.2. ATA Command for ATAPI CD-ROM Devices Command OP Code XM-7002B ATAPI SOFT RESET 08h YES CHECK POWER MODE E5h YES EXECUTE DRIVE DIAGNOSTICS 90h YES IDLE IMMEDIATE E1h YES IDLE E3h YES NOP 00h YES ATAPI PACKET COMMAND A0h YES ATAPI IDENTIFY DEVICE A1h YES SET FEATURES EFh YES SLEEP E6h YES STANDBY IMMEDIATE E0h YES STANDBY E2h YES

• Toshiba XM-7002B, 13/27 XM-7002B Rev.1.0 5.3. Standby mode Figure 8 shows the standby sequence. During acces s ldle (4.4 - 10X) 8 s 24 s ldle (Max.24X) command Read or Seek Figure 8 Standby Sequence Rotational speed move onto 4.4 to 10X mode in 8 seconds of the Read or Seek command. After 24 seconds (default value), it move onto standby mode. (a stop spindle motor) 6. Interface (1) The interface is based on ATA-SPEC, ATAPI-SPEC SFF-8020i Revision 2.6, SFF-8028 Revision 1.0 and SFF-8090 version 2. (Small Form Factor Committee Specification of ATA-Packet Interface for CD-ROMs) (2) 48 types of commands a

• Toshiba XM-7002B, 23/27 XM-7002B Rev.1.0 10. Busy Indicator The LED at Front Bezel (Busy Indicator) indicates the drive status. Color: UMBER (1) After Drawer is closed, Busy Indicator start blinking at 0.8 s intervals, and then ----- (1-1) Turns off when the drive in the 'Idle' status. 0.8 s Light Off Figure 15 Idle (1-2) Continuously off when no disc is mounted. 0.8 s Light Off Figure 16 No disc (1-3) Continuously on when media has problem 0.8 s Light On Figure 17 Media Problem (2) When playing an audio track, Busy Indicator is blinking at 1.6 s intervals. 1.6 s Figurer 18 CD-Audio playback (3) When performing 'Data Access' and

• Toshiba XM-7002B, 10/27 XM-7002B Rev.1.0 3.5. Reliability 3.5.1. Error Rate (1) Hard Read Error Rate (Byte Error Rate) ----- Allowing 10 Retries ----- Yellow-Book Mode 1/Mode 2 Form1 10 -15 Max Yellow-Book Mode 2/Mode 2 Form2 10 -12 Max (2) Seek Error Rate ---Allowing Retries--- 10 -6 Max 3.5.2. MTBF 60,000 POH Assumptions: Power On Hours 5,436 h/year On/Off Cycles 312 cycles/year Number of Access 600,000 accesses/year Operating Duty Cycle 20 % of Power On Time (Reading/Seeking) 3.5.3. MTTR 0.5 h 3.5.4. Drive Life 15,000 h or 5 years(earlier one) 3.5.5

• Toshiba XM-7002B, 14/27 XM-7002B Rev.1.0 6.2.1.Signal Specifications Figure 9 shows the Signal Specifications N P N Sig. Name DD0 -DD15 /DASP /PDIAG Type Bidirectional IOL Driver sink current Min Max 12 mA VOH Voltage Output High Vdd-0.4 V VOL Voltage Output Low 0.4 V IOH=1 mA IOL=12 mA VIH Input HIGH Voltage 2.0 V TTL VIL Input LOW Voltage ILI -5 µA -150 µA TTL Pullup Resistor(Ri) ILO Input leakage Current Output Leakage Current -30 µA Pullup Resistor(Ri) CI Input Capacitance 8 pF CO Output Capacitance 8 pF Open

• Toshiba XM-7002B, 25/27 XM-7002B Rev.1.0 14. Electrostatic Discharge (1) Operating (Air discharge) 15 kV or less (2) Damage including (Air discharge) 20 kV or more 15. Accessories Non 16. Packaging a. 25 units in a Bulk Pack 36 Bulk Packs on one Pallet *Transportaion must be executed with each palette. b. 20 units in a Bulk Pack 24 Bulk Packs on one Pallet Packing Specifications :for 25 Packaged Model: IB-CD2-A90012 :for 20 Packaged Model: IB-CD2-A90013 17. CE Declaration of conformity Please refer to attached Annex 1.

• Toshiba XM-7002B, 19/27 XM-7002B Rev.1.0 6.4.Support Command List 6.4.1. ATAPI Packet Command for CD-ROM Devices Command OP Code XM-7002B AUDIO SCAN BAh YES GET EVENT STATUS NOTIFICATION 4Ah YES GET CONFIGRATION COMMAND 46h YES GET PERFORMANCE COMMAND ACh YES INQUIRY 12h YES MECHANISM STATUS BDh YES MODE SELECT(10) 55h YES MODE SENSE(10) 5Ah YES PAUSE/RESUME 4Bh YES PLAY AUDIO(10) 45h YES PLAY AUDIO(12) A5h YES PLAY AUDIO MSF 47h YES PLAY TRACK RELATIVE(10) 49h YES PLAY TRACK RELATIVE(12) A9h YES PREVENT/ALLOW MEDIUM REMOVAL 1Eh YES READ(10) 28h YES READ(12) A8h YES READ C/DVD CAPACITY 25h YES READ CD BEh YES READ CD MSF B9h YES READ DISC

• 12/27 XM-7002B Rev.1.0 5. Functions 5.1. CD-ROM Data Configurations Figure 6 shows how the data is structured in program units. 1block=1/75 s Time TNO TOC 0 Lead-in Min Sec Block Block 1 Min Sec Block 1 Block 2 2 approx. 300k- Blocks ~ ~ ~ ~ AA Lead out 1-Disc SYNC 12 bytes Header User Data 2048 bytes in Mode-1 2336 bytes in Mode-2 ~ ~ ~ ~ ECC(Mode-1) 288 bytes Minutes Second(

• Toshiba XM-7002B, 1/27 XM-7002B Rev.1.0 1. Introduction This document describes Toshiba's XM-7002B CD-ROM Drive. This drive reads digital data stored on CD-ROM and CD-Audio discs. The CD-ROM disc is single sided and has a 12 cm or 8 cm diameter. It typically contains approximately 600 MBytes or 200 MBytes of information respectively. (1 MByte=2 20 Bytes) This drive reads digital data stored on CD-ROM discs at maximum 24 times faster rotational speed. This drive is a new generation drive with highest performance such as 95 ms (target) access Time. This drive shows highest performance such as 60,000 hour MTBF. This drive offer long life and high

• Toshiba XM-7002B, XM-7002B Rev.1.0 Notice 1.This product has no over-current protection circuit. System should have appropriate over-current protection. Toshiba Corporation makes no warranty of damages caused by no over-current protection. 2.This has a little possibility of errors. To prevent damages and injury caused by the above, careful consideration for the safety and integrity should be taken in the system design. Do not use this product in a system that may cause hazard to human being or material loss caused by the failure, loss of data and/or errors of this product

• Toshiba XM-7002B, 21/27 XM-7002B Rev.1.0 7. Power Requirements 7.1. Source Voltage +5 V +/-5 % (Operating) 7.1.1 Spike 100 mV (p-p) Max 7.1.2 Ripple 100 mV (p-p) Max 7.2. Current Drain (Typ. Value) 7.2.1. Sleep(Minimum Current Mode) 0.025 A 7.2.2. Standby(Laser off,motor off) 0.03 A 7.2.3. Idle(Laser on,motor on) 0.32 A Start Position 7.2.4. Continuous Read(Audio/Data) 0.62 A (Max.24X) / 0.35 A (Max.10X) Start Position 7.2.5. Average(20% Duty Random Access) 0.64 A (Max.24X) / 0.34 A (Max.10X) 7.2.6. Maximum(100% Duty Random Acce

• 8/27 XM-7002B Rev.1.0 3.3.4. Vibration detection (1) This drive detects vibration which occurs when unbalanced disc is played, and rotation speed of two steps (16X, 10X) is selected according to the vibration level and the rotation speed is dropped automatically. It is necessary to mount the drive stably in PC to detect the vibration correctly. (2) This drive was tuned

• 17/27 XM-7002B Rev.1.0 6.2.4.Timing of Host Interface (Ultra DMA ) Figure 12 shows the Host Interface Ultra DMA word Timings DMARQ DMACK- STOP DMARDY STROBE DD (15:0) tMLI tUI tACK tFS tENV t2AD t2IORDY t2CYC tRP tRFS tLI tACK tDVS tDVH CRC tDVHtDVS tDVH tDVS tDVHtDVS tCYC tCYC Ultra DMA Mode 2 timing parameters min (ns) max (ns) Min time (ns) Max time (ns) t2CYC Typical Sustained Aver

Related Products and Documents (Storage):

Comparable Devices:

Similar Resources:

• Nexcom iNAS 330 (19 pages) NEXCOM International Co., Ltd.NEXCOM International Co., Ltd.Published January 2018www.nexcom.comNetwork and Communication SolutionsIndustrial StorageiNAS 330Hardware User Manual …

• Keter 17191974 (2 pages) ASSEMBLY INSTRUCTIONS | INSTRUCCIONES DE MONTA JE | MONTAGEANLEITUNG | CONSIGNES DE MONTAGE | SAMLEVEJLEDNING | MONTAGE-VOORSCHRIFTEN | ISTRUZIONI D’ASSEMBLAGGIO270L/71GalWWW.KETER.COMIF THERE ARE MISSING OR BROKEN PARTS, PLEASE DO NOT RETURN THE PRODUCT TO THE STOREPlease log onto our website, or contact Customer Service.S’IL Y A …

• NetApp FAS8200 Series (4 pages) Prepare for installation Install hardware Cable storageComplete system setupand configuration1 2 3 4FAS8200 SystemsInstallation and Setup InstructionsPrepare for installation | 1Screwdriver Windows clientRuns the software to configureyour storage systemRack space3U per chassisYou provideIn the boxPower cablesController-to-controller cablesCluster interconn …

• Compaq DL360 - ProLiant - Photon (11 pages) Implementing Microsoft® Windows Server® 2008 Foundation on HP ProLiant servers integration note Abstract.............................................................................................................................................. 2 Introduction to Windows Server 2008 Foundation............................................................. …

• Seagate ST1000LM014 (33 pages) Product ManualSeagate® Laptop SSHDGen 1100716627Rev. CJune 2013Standard models ST1000LM014ST750LM000Self-Encrypting Drive models ST1000LM015SED (FIPS 140-2) models ST1000LM028 …

• Buffalo TeraStation (2 pages) 35011966 ver.01Hard Drive Replacement ProcedureHard Drive Replacement ProcedureWhen a hard drive in the TeraStation has failed, its Error LED will flash red.Open the front cover of the TeraStation and check the Status LEDs. Any hard drive whose Status LED is lit or flashing red is malfunctioning. You may hot-swap a hard drive whose Status LED is lit. The …

Comments, Questions and Opinions: