Toshiba Satellite Pro 4300 Installation And Operation Manual
|
Toshiba Satellite Pro 4300, 46 4300 Series Installation and Operation Manual 12.15 Tab: Setup The SETUP tab allows the user to adjust certain UPS parameters. The setup tab shows 12 buttons. Inactive buttons are indicated with a “x” in the lower right-hand corner of the button. The table below, right, shows a typical SETUP button. Typical Button Signicance No “x” in the lower right corner indicates the button is active. Pressing the button will open a data page displaying the parameters available at the current security level. A button that has an “x” in the lower right corner is inactive and cannot be accessed at the current security level. Param. Prex Parameter Ca
Toshiba Satellite Pro 4300, 13 4300 Series Installation and Operation Manual The warning labels identied on the previous page are located on the front and interior of the UPS. Their location is shown in Figures 6.2 - 6.3. FIGURE 6.2 – EXTERNAL WARNING LABEL FIGURE 6.3 – INTERNAL WARNING LABEL LOCATIONS B A D B C C B B
Toshiba Satellite Pro 4300, 72 4300 Series Installation and Operation Manual TOSHIBA 4300 UPS Installation Planning Guide for 30/50kVA UPS Standard System: 208/120V Input, 208/120V Output Rev. 0 Page 1 of 2 4300-IPG-208/120v-208/120V General Mechanical Information UPS kVA/ kW Rating Dimensions (W x D x H) Weight Approximate Full-Load Heat Loss Inches Lbs. kBtu/Hr 30 kVA/ 24 kW 22 x 31.5 x 73.26 788 9.0 50 kVA/ 45 kW 22 x 31.5 x 73.26 867 15.2 Primary AC Input (208/120V 3-Phase / 4-Wire) Maximum Input Power Demand Suggested External F
Toshiba Satellite Pro 4300, 16 4300 Series Installation and Operation Manual 7.3 Maintenance Precautions All internal maintenance should be performed by factory authorized personnel. 1) Turn off, lockout, and tagout ALL power sources before connecting the power wiring to the equipment or when performing maintenance. 2) Hardwire type UPS units are not equipped with an over-current protection device, nor do they have an output disconnect for the AC output. A user-installed circuit breaker should be provided between the UPS output and the load input. 3) The maximum ambient operating tempe
Toshiba Satellite Pro 4300, 43 4300 Series Installation and Operation Manual 12.13 Tab: Main The Main tab displays the UPS Serial Number and Typeform. Main Tab Components No. Function 1 Serial Number - UPS Serial Number 2 Typeform - UPS typeform 3 Information Bar - Randomly displays status, helpful hints, acronym denitions every two seconds. FIGURE 12.10 – MAIN TAB COMPONENTS 1 2 3
Toshiba Satellite Pro 4300, 47 4300 Series Installation and Operation Manual Tab: SETUP (cont.) Pressing an active button will cause a list of parameters to be displayed (See previous page). Pressing a listed parameter will activate a display appropriate to the parameter selections available If the parameter cannot be edited at the current security level, the display will not change. If the parameter can be edited or changed, an appropriate keypad will displayed as shown below. Either a alpha/numeric keypad, a multiple choice, or binary choice display will appear. After entering data or selecting an options, press WRITE to save the selectio
Toshiba Satellite Pro 4300, 37 4300 Series Installation and Operation Manual 12.5 Header Bar The Header Bar on the graphic display panel displays three system parameters: the System Load, Cur- rent Status, and System Time. Header Bar Components No. Function 1 System Load - Load per each phase as percent of full load. Low - Less than 10% Load. 2 Current Status - UPS status at the moment. (Status is delayed by a few seconds) 3 System Time - Current time in AM-PM format FIGURE 12.4 – HEADER BAR DISPLAY COMPONENTS 12.6 Footer Bar T
1 4300 Series Installation and Operation Manual 1 Introduction This manual provides information on how to safely operate your 4300 Series Uninterruptible Power System (UPS). This manual includes a section of general safety instructions that describes the warning labels and symbols that are used throughout the manual. Read the manual completely before installing, operatin
Toshiba Satellite Pro 4300, 7 4300 Series Installation and Operation Manual 4.4 Transporting By Forklift Refer to Chapter 15 - Weight and Dimensions. Verify forklift maximum load capacity and ensure that the forks are long enough to properly support the UPS. Insert the forks into the space shown in Figure 4.1. Spaces for the forks are provided underneath the UPS. DO NOT tilt UPS when lifting and/or transporting. Minimize the impact when lowering the UPS to the oor. FIGURE 4.1 -TRANSPORTING UPS BY FORKLIFT 7 in. 7 in.13.7 in. 4300 Side View - Fork Access Dimensions i
Toshiba Satellite Pro 4300, 28 4300 Series Installation and Operation Manual 10.2 UPS LAN Shutdown Signal Operation When the UPS stop signal is sent to the UPS through pin 2 and 3 of the external contact interface, it is possible to automatically reset the following operating systems (OS), which can automatically implement the shutdown function and restart the operation: Windows NT, IBM OS/2 LAN server, LANtastic Parameter 641 – UPS Shutdown by LAN Input Signal Enabled/Disabled Parameter 642 – UPS Shutdown by LAN Signal Permitted Time Window (Adjustable) With the UPS Shutdown by LAN Signal function enabled, when line power fails and the UPS goes to backup the LAN will shutdow
Toshiba Satellite Pro 4300, 26 4300 Series Installation and Operation Manual 9.4 External Breakers The UPS is not equipped with isolation circuit breakers. Qualied personnel should provide the external breakers for the AC input/output, bypass input and DC input. See Figure 11.1 – External Wiring Diagram, for the circuit position of the breakers. Table 11.7 shows the minimum external breaker rating for each UPS. The bypass, input and output require 3-pole breakers. TABLE 9.2 UPS MINIMUM DEVICE RATINGS CapaCity Rated Output input
Toshiba Satellite Pro 4300, 65 4300 Series Installation and Operation Manual 13.5 Battery Low Voltage Tolerances The battery charging period varies depending on the amount of discharge during backup. Figure 13.2 shows the typical recharge curve for a fully discharged battery. Charging Period Explanation Period 1 Initial charging at maximum current (limited by charger). V min is minimum voltage at which the UPS will shut down power to the load. Period 2 Charging rate drops as battery voltage increases. Period 3 Battery cells are at maximum voltage, UPS continues to provide a “trickle charge” to keep the batt
61 4300 Series Installation and Operation Manual LB Low Battery – The battery voltage has dropped low (about 90% or less) during operation. Contin- ued operation in this mode will deplete battery and cause output shut down. (This can be adjusted by the operator Immediately shut down the load equipment in an orderly fashion and then press the STOP key. LCRUN Local r
Toshiba Satellite Pro 4300, 21 4300 Series Installation and Operation Manual 1 2 TABLE 8.1 UPS COMPONENT LOCATION AND IDENTIFICATION No. Description 1 Front Panel Display 2 Locking Door Latch with op- tional Lockout/Tagout Hasp 3 Upper Deadfront 4 Middle Deadfront 5 Lower Deadfront 6 MCCB - Primary Input Circuit Breaker 7 (Optional) Secondary Input Circuit Breaker 8 (Optional) Air lter 7 4 6 5 3 8.5 UPS Parts Identication The following table identies the major components of the UPS. 8
Toshiba Satellite Pro 4300, 8 4300 Series Installation and Operation Manual 4.5 Inspection/Storage Inspection Upon receipt of the UPS, an inspection for shipping damage should be performed. Use caution when removing the unit from the pallet. Refer to labels or documentation attached to packing material. Unpacking Check the unit for loose, broken, bent or otherwise damaged parts. If damage has occurred during shipping, keep all original crating and packing materials for return to the shipping agent. NOTE: The factory warran
Toshiba Satellite Pro 4300, 42 4300 Series Installation and Operation Manual 4 1 5 2 3 FIGURE 12-9 QUICK VIEW DISPLAY 12.12 Toolbar: QUICK VIEW ON/OFF At anytime while using the tabs to view system details, the summary of the UPS Input, Output, and DC Bus can be viewed by pressing the Q. VIEW button (Button will display Q. VIEW ON). The illustration below highlights the critical features of the Quick View display. Exit Quick View by pressing the Q. VIEW button again. (Button will display Q. VIEW OFF) TABLE 12.3 - QUICK VIEW DISPLAY No. Description 1 Displays Vin, Vout, and Vbyp for all three phases 2 Changes voltage display mode: Press repeatedly to display sequentially the voltage as: Line-to-Line (LL), Li
Toshiba Satellite Pro 4300, 48 4300 Series Installation and Operation Manual 12.16 Setup: Calibrating the Touchscreen At anytime while using the tabs to view system details, the touchscreen can be calibrated by executing the built-in calibration routine. To calibrate the touchscreen: 1. Press the Setup Tab. 2. Press the DISP-EX 800 button 3. Press the entry Cali to begin the calibration routine 4. Follow the directions on the display to press the “+” at each location it ashes on the display. To exit the calibration routine press QUIT at any time. See Fig. 2-10 A, B. 5. After the touchscreen has been recalibrated the display will indicate that t
10 4300 Series Installation and Operation Manual 1) The UPS generates and can radiate radio-frequency energy during operation. Although RFI noise lters are installed inside of the unit, there is no guarantee that the UPS will not inuence some sensitive devices that are operating near by. If such interference is experienced, the UPS should be installed further away from the affe
Toshiba Satellite Pro 4300, 45 4300 Series Installation and Operation Manual The mimic display indicates the power ow through, or around, the UPS. There are four possible modes the UPS operates in: Off, Bypass, On-Line, and Backup. The gure below illustrates the display for each of these modes. FIGURE 12-12 MIMIC DISPLAY CURRENT FLOW INDICATOR Mode: OFF Mode: Bypass Mode: On-line Mode: Backup
Toshiba Satellite Pro 4300, 18 4300 Series Installation and Operation Manual 8.1 Unpacking Unpack the UPS indoors on a paved oor. The UPS should be as close as possible to its nal storage location. Allow enough space for forklift operations to unpack the UPS crate. Then remove the crate. Points to observe • Retain all small articles during unpacking and installation. • Make sure that exterior paint is not scratched and that the UPS cabinet is not damaged. • DO NOT damage the UPS when using tools to remove packaging materials. • If provided, DO NOT remove the plastic sheet cover, until installation. • Do not remove the fan covers until UPS start up. The fan covers should be
Toshiba Satellite Pro 4300, 25 4300 Series Installation and Operation Manual 9.2 Multiple Battery Cabinets No more than two Toshiba 4300 Battery Cabinets may be connected in parallel to the 4300. DC Backup Source cabinets that are not line up and match may be combined to extend the UPS backup runtime. Typically these cabinets must be connected with either a bus structure or to a single point con- nection outside the UPS. Contact the factory if using more than one DC Source Backup cabinet. 9.3 30/50 kVA Terminal Blocks and Power Cables Note: Always consult your site specic, local, state, and NEC electrical codes for wiring, cabling, and circuit protection device requirements. The terminal bloc
Toshiba Satellite Pro 4300, 74 4300 Series Installation and Operation Manual STEP 2: Slide Side Plates in along C-Channel base. 2.1 Facing the front of the UPS, slide a side kick plate with the smooth side facing out down along the left base C-channel skid until it is protruding about one inch in front of the UPS. See Figure B2. 2.2 Repeat for the right C-channel skid. STEP 3: Align the F/B Plate with the UPS front. Place a F/B kick plate on the oor as in Step 1. Angle the right edge out away from the UPS until the pair of front slots at the ends of the F/B kick plate are visible. See Figure B3. STEP 4: Insert Side Pl
6 4300 Series Installation and Operation Manual 4.3 Transporting The UPS may be packed in a crate for extra protection during transportation. Avoid impact or vibration against the UPS during transportation. DO NOT expose the UPS directly to water. WARNING DO NOT tilt the UPS more than 10° from upright position. Tilting the UPS more than 10° may cause crushing, trapping or other pers
DOWNLOAD |
Toshiba 1600EP Series UPS Instruction manual
1600EP Series |
Toshiba Satellite 4200 UPS Replacement manual
Satellite 4200 |
Toshiba 4200FA UPS Installation and operation manual
4200FA |
Toshiba 4200FA UPS Installation planning manual
4200FA |
Toshiba Satellite 4200 UPS Operation manual
Satellite 4200 |
Toshiba UNINTERRUPTIBLE POWER SYSTEM 1600XP UPS Installation and operation manual
UNINTERRUPTIBLE POWER SYSTEM 1600XP |
Toshiba G9000 SERIES UPS Installation and operation manual
G9000 SERIES |
Toshiba 4200FA UPS Operation & user’s manual
4200FA |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | Holder | C4.74 | Operating instructions manual | holder/c4-74-116.pdf | 16 Sep 2022 | 212 | 4.45 Mb |
2 | Memorex | MDF0722-WLDB | Features | memorex/mdf0722-wldb-X28.pdf | 05 Sep 2023 | 1 | |
3 | Fluke | MPC1 VARIABLE VOLUME REPAIR KIT | Installation instructions | fluke/mpc1-variable-volume-repair-kit-9Z9.pdf | 06 Apr 2023 | 2 | 0.1 Mb |
4 | Intermec | CN50 | Operation & user’s manual | intermec/cn50-YT4.pdf | 15 Feb 2024 | 96 | |
5 | Yamaha | S250X | Operating manual | yamaha/s250x-692.pdf | 27 Sep 2023 | 6 | 0.65 Mb |
6 | Toshiba | ICC MBP-100 | Instruction manual | toshiba/icc-mbp-100-Z3G.pdf | 20 Jun 2023 | 76 | 1.35 Mb |
Tripp Lite
Owner’s Manual1111 W. 35th Street Chicago, IL 60609 USA • Customer Support: (773) 869-1234 • www.tripplite.comImportant Safety Instructions2Quick Installation3Optional Installation4Storage and Service10Specifications11SmartPro®SLT & SmartPro®XLIntelligent Tower (Accessory Slot-Equipped) UPS Systems • Line-Interactive Operation • Sine-Wave O …
1500SLT(20 pages) |
inform
288713230 IINNFFOORRMMEERR SSEERRIIEESS Uninterruptible Power System Line Interactive UPS 1000VA/ 2000VA/ 3000VA USER MANUAL
…
Informer 1000VA(7 pages) |
Panamax
BANKS WIRING1 2POWER MENU MB1000FAULT0 VOLTS INEST’D BATTERY: 60 MINMB1000 InstructionsA Fully Programmable, Uninterruptible Power Supply, Voltage Regulator & Power ConditionerFeatures:• Surge Protection and AVM• LiFT Noise Filtration• …
MB1000(52 pages) |
Phasak
SERIE INTERACTIVE [ES] PH 9465 PH 9469 PH 9485 LEA AL MENOS ESTO Siga estrictamente todas las advertencias e instrucciones de este manual. Antes de instalar esta unidad, lea todas las instrucciones atentamente. No utilice este SAI antes de leer atentamente toda la información de seguridad y las ins …
PH 9465(21 pages) |
ABB
4NWP100559R0001_OPM_ABB_PVA31-11-T_10-20kVA_EN_140626 Page 1/37 ABBModifications reservedPowerValue 31/11 T 10/20 kVAUser Manual4NWP100559R0001_OPM_ABB_PVA31-11-T_10-20kVA_EN_140626© Copyright 2014 ABB, All rights reserved.
…
PowerValue 31/11 T 10 kVA(37 pages) |
Aros
UNINTERRUPTIBLE POWER SUPPLY LINE-INTERACTIVE 500-3000VA (BATTERY BOX) - Manuale d’uso - - User’s manual - - Bedienungsanleitung -
…
Spring 500-3000VA(41 pages) |
Trix Toy BR 50PDF User Manual (@5Q4P13), Trix BR 50 Toy (Sun 11.2023) BR 50, 28 |
Canon Film Camera EOS 3000 NFilm Camera Instructions manual (Canon EOS 3000 N) EOS 3000 N, 83 |
pro.point Welding Accessories 85108518510851 Operation & user’s manual - JRF6H9 8510851, 28 |
Panasonic Flat Panel TV TX-20LA2APDF User Manual (@VLHI5U), Panasonic TX-20LA2A Flat Panel TV (23rd Feb 2024) TX-20LA2A, 28 |
Motorola Docking Station HD DockDocking Station #GW82RP HD Dock, 66 |
EVGA Video Card GeForce GTS 450 FTWVideo Card #VH25JH GeForce GTS 450 FTW, 1 |
GE Refrigerator r10965v-1#JJ5349 r10965v-1: GE Refrigerator Owner Documentation r10965v-1, 32 |
Stanley Grinder STGS9100Stanley STGS9100 User Guide (Doc Type: Grinder Owner's manual) STGS9100, 16 |
HomComfort Heater HCPH SSPDF User Manual (@T78AGG), HomComfort HCPH SS Heater (Tue 10.2023) HCPH SS, 16 |
SOLAC Fan VT8800Fan #6Z67XM VT8800, 34 |
Skytec Speakers 170.311Speakers #14856N 170.311, 5 |
Sony TV KV-32FS210Sony Product Manual: KV-32FS210 PDF Operating instructions manual - IA94JT KV-32FS210, 57 |