Manualios.com

Foundry Networks 2402CF Installation Manual

Foundry Networks 2402CF Manual Online:

3.3, 1322 votes
Foundry Networks 2402CF User Manual
Foundry Networks 2402CF User Guide
Foundry Networks 2402CF Online Manual

Text of Foundry Networks 2402CF User Guide:

  • Foundry Networks 2402CF, C ONNECTING TO A P OWER S OURCE February 2003 © 2003 Foundry Networks, Inc. 4-5 Figure 4-3. Attaching the Adhesive Feet 2. Set the device on a flat surface near an AC power source, making sure there are at least two inches of space on all sides for proper air flow. 3. If installing a single switch only, go to “Connecting to a Power Source” at the end of this chapter. 4. If installing multiple switches, attach four adhesive feet to each one. Place each device squarely on top of the one below, in any order. Connecting to a Power Source To connect a device to a power source: 1. Insert the power cable plug directly into the receptacle located at the back of the device.

  • Foundry Networks 2402CF, C ABLES B-8 © 2003 Foundry Networks, Inc. February 2003 Console to 25-Pin DTE Port on PC Switch’s 9-Pin Se- rial Port Null Modem PC’s 9-Pin DTE Port 2 RXD <--------- TXD ------------ 3 TXD 3 TXD ----------- RXD ----------> 2 RXD 5 SGND ----------- SGND ---------- 5 SGND No other pins are used. Switch’s 9-Pin Se- rial Port Null Modem PC’s 25-Pin DTE Port 2 RXD <--------- TXD ------------ 2 TXD 3 TXD ----------- RXD ----------> 3 RXD 5 SGND ----------- SGND ---------- 7 SGND No other pins are used.

  • Foundry Networks 2402CF, M OUNTING February 2003 © 2003 Foundry Networks, Inc. 4-3 Mounting A switch unit can be mounted in a standard 19-inch equipment rack or on a desktop or shelf. Mounting instructions for each type of site follow. Rack Mounting Before rack mounting the switch, pay particular attention to the following factors: • Temperature: Since the temperature within a rack assembly may be higher than the ambient room temperature, check that the rack-environment temperature is within the specified operating temperature range. (See page -2.) • Mechanical Loading: Do not place any equipment on top o

  • Foundry Networks 2402CF, February 2003 © 2003 Foundry Networks, Inc. Glossary-5 Transmission Control Protocol/Internet Protocol (TCP/IP) Protocol suite that includes TCP as the primary transport protocol, and IP as the network layer protocol. UTP Unshielded twisted-pair cable.

  • Foundry Networks 2402CF, February 2003 © 2003 Foundry Networks, Inc. C-1 APPENDIX C SPECIFICATIONS Physical Characteristics Base Unit Ports 24 10BASE-T/100BASE-TX, with auto-negotiation 2 slots for optional 1000BASE-T, 1000BASE-SX,1000BASE-LX, and 1000BASE-X GBIC modules Network Interface 10BASE-T: RJ-45 (100-ohm, UTP cable; Categories 3, 4, 5) 100BASE-TX:RJ-45 (100-ohm, UTP cable; Category 5) Ports 1-24: RJ-45 connectors, auto MDI/MDI-X Communication Speed 10 and 100 Mbps Communication Mode Full and half duplex Buffer Architect

  • Foundry Networks 2402CF, Copyright © 2003 Foundry Networks, Inc. All rights reserved. No part of this work may be reproduced in any form or by any means – graphic, electronic or mechanical, including photocopying, recording, taping or storage in an information retrieval system – without prior written permission of the copyright owner. The trademarks, logos and service marks ("Marks") displayed herein are the property of Foundry or other third parties. You are not permitted to use these Marks without the prior written consent of Foundry or such appropriate third party. Foundry Networks, BigIron, FastIron

  • Foundry Networks 2402CF, T WI STED -P AIR C ABLE AND P IN A SSIGNMENTS February 2003 © 2003 Foundry Networks, Inc. B-3 network connections to PCs or servers, or to other switches or hubs. The RJ-45 port on the 100BASE-TX module is an MDI-X port, which allows you to use straight-through cable for connections to PCs and servers. In straight-through cable, pins 1, 2, 3, and 6, at one end of the cable, are connected straight through to pins 1, 2, 3, and 6 at the other end of the cable. For connection to hubs or switches which have MDI-X ports, a crossover cable must be used. Pin MDI-X Signal Name MDI Signal Name 1 Receive D

  • Foundry Networks 2402CF, & YL )RXQGU\1HWZRUNV,QF )HEUXDU\ 15. Zum Netzanschluß dieses Gerätes ist eine geprüfte Leitung zu verwenden. Für einen Nennstrom bis 6 A und einem Gerätegewicht größer 3 kg ist eine Leitung nicht leichter als H05VV-F, 3G, 0.75 mm 2 einzusetzen. Der arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 Teil 1000 beträgt 70 dB(A) oder weniger.

  • Foundry Networks 2402CF, A BOUT T HIS G UIDE 1-2 © 2003 Foundry Networks, Inc. February 2003 Foundry Networks Technical Support Foundry Networks technical support will ensure that the fast and easy access that you have come to expect from your Foundry Networks products will be maintained. Web Access Point your browser to the following URL: http://www.foundrynetworks.com. Navigate to Services/Technical Support. Click the Login button, then enter your user name and password to gain access to the Foundry support site. E-mail Access Technical requests can also be sent to the e-mail address: VXSSRUW#IRXQGU\QHWFRP Telephone Access ◆ 785%2&$//�

  • C ABLES B-4 © 2003 Foundry Networks, Inc. February 2003 Straight-Through Wiring If the twisted-pair cable is to join two ports and only one of the ports has an internal crossover (MDI-X), the two pairs of wires must be straight-through. Crossover Wiring If the twisted-pair cable is to join two ports and either both ports are labeled with an “X” (MDI-X) or neith

  • O VERVIEW February 2003 © 2003 Foundry Networks, Inc. 2-3 The management agent provides a wide range of advanced performance-enhancing features. Port-based VLANs provide traffic security and efficient use of network bandwidth. QoS priority queueing ensures the minimum delay for mo v in g real-time multimedia data through the switch. Flow control eliminates the loss o

  • Foundry Networks 2402CF, February 2003 © 2003 Foundry Networks, Inc. Glossary-1 GLOSSARY 10BASE-T IEEE 802.3 specification for 10 Mbps Ethernet over two pairs of Category 3, 4, or 5 UTP cable. 100BASE-TX IEEE 802.3u specification for 100 Mbps Fast Ethernet over two pairs of Category 5 UTP cable. 1000BASE-LX IEEE 802.3z specification for Gigabit Ethernet over one strand of 9/125 micron core fiber cable. 1000BASE-LH Gigabit Ethernet over two strands of 9/125 micron core fiber cable. 1000BASE-SX IEEE 802.3z specification for Gigabit Ethernet over two strands of 50/125 or 62.5/125 micron core fiber cable. 1000BASE-T IEEE 802.3ab specificat

  • Foundry Networks 2402CF, D ESCRI PTI ON OF H ARDWARE February 2003 © 2003 Foundry Networks, Inc. 2-7 Power Supply Receptacle The power receptacle is located on the rear panel of the switch. The standard power receptacle is for the AC power cord. Diag On Green The system diagnostic test has completed successfully. Flashing Green The system diagnostic test is in progress. On Amber The system diagnostic test has detected a fault. Link N/A This indicator is not currently implemented. Duplex N/A This indicator is not currently implemented. Stack Flashing Amber An initial state of stacking configuration upon powering on. Green This switch is acting as the master unit in the s

  • Foundry Networks 2402CF, February 2003 © 2003 Foundry Networks, Inc. B-1 APPENDIX B CABLES Specifications Cable Types and Specifications Cable Type Max. Length Connector 10BASE-T Cat. 3, 4, 5 100-ohm UTP 100 m (328 ft) RJ-45 100BASE-TX Cat. 5 100-ohm UTP 100 m (328 ft) RJ-45 1000BASE-SX 50/125 or 62.5/125 micron core MMF See the following table SC 1000BASE-LX 9/125 micron SMF 5 km (3.12 miles) SC 1000BASE-T Cat. 5, 5e 100-ohm UTP 100 m (328 ft) RJ-45 1000BASE-SX Fiber Specifications Fiber Diameter Fiber Bandwidth Maximum Cable Length 62.5/125 micron MMF 160 MHz/km 2-220 m (7-722 ft) 200 MHz/km 2-275 m (7-902 ft) 50/125

  • February 2003 © 2003 Foundry Networks, Inc. A-1 APPENDIX A TROUBLESHOOTING Diagnosing Switch Indicators Troubleshooting Chart Symptom Action PWR LED is Off • Internal power supply is disconnected. • Check connections between the switch, the power cord, the wall outlet. PWR LED is Amber • Internal power supply has failed. • Contact your local dealer for as

  • Foundry Networks 2402CF, February 2003 © 2003 Foundry Networks, Inc. 3-1 CHAPTER 3 NETWORK PLANNING Introduction to Switching A network switch allows simultaneous transmission of multiple packets via non-crossbar switching. This means that it can partition a network more efficiently than bridges or routers. The switch has, therefore, been recognized as one of the most important building blocks for today’s networking technology. When performance bottlenecks are caused by congestion at the network access point (such as the network card for a high-volume file ser

  • Foundry Networks 2402CF, & LL )RXQGU\1HWZRUNV,QF )HEUXDU\ 68/EEC. For the evaluation of the compliance with these Directives, the following standards were applied: Warning: Do not plug a phone jack connector in the RJ-45 port. This may damage this device. Les raccordeurs ne sont pas utilisé pour le systéme téléphonique! RFI Emission: • Limit class A according to EN 55022:1998 • Limit class A for harmonic current emission according to EN 61000-3-2/1995 • Limitation of voltage

  • )HEUXDU\ )RXQGU\1HWZRUNV,QF L COMPLIANCES FCC - Class A This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A com

  • Foundry Networks 2402CF, & )HEUXDU\ )RXQGU\1HWZRUNV,QF Y The unit automatically matches the connected input voltage. Therefore, no additional adjustments are necessary when connecting it to any input voltage within the range marked on the rear panel. Wichtige Sicherheitshinweise (Germany) 1. Bitte lesen Sie diese Hinweise sorgfältig durch. 2. Heben Sie diese Anleitung für den späteren Gebrauch auf. 3. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Verwenden Sie keine Flüssigoder Aerosolreiniger. Am best

  • Foundry Networks 2402CF, February 2003 © 2003 Foundry Networks, Inc. 1-1 CHAPTER 1 ABOUT THIS GUIDE Audience This guide is for system administrators with a working knowledge of network management. You should be familiar with switching and networking concepts. Nomenclature This guide uses the following typographical conventions to show information: Italichighlights the title of another publication and occasionally emphasizes a word or phrase. codeshows text that must be entered exactly as it appears in this guide. 1RWH emphasizes an important fact or cal

  • Foundry Networks 2402CF, M AKING N ETWORK C ONNE CT IONS 5-4 © 2003 Foundry Networks, Inc. February 2003 1. Attach one end of a patch cable to an available port on the switch, and the other end to the patch panel. 2. If not already in place, attach one end of a cable segment to the back of the patch panel where the punch-down block is located, and the other end to a modular wall outlet. 3. Label the cables to simplify future troubleshooting. Figure 5-2. Wiring Closet Connections Equipment Rack (side view) 24-Port Fast Ethernet Switch Patch Panel Punch-Down Block Wall

  • Foundry Networks 2402CF, S PECI FI CATIONS C-4 © 2003 Foundry Networks, Inc. February 2003 IEEE 802.1x RADIUS user authentication IEEE 802.3x full-duplex flow control ISO/IEC 8802-3 UDP (RFC 768), IP (RFC 791), TCP (RFC793), TFTP (RFC 783), TELNET (RFC 783), SNMP (RFC 1157), MIB II (RFC 1213), Traps (RFC 1215), Bridge MIB (RFC 1493), RMON (RFC 1757), HTML (RFC 1866), HTTP (RFC 2068), RADIUS (RFC 2618) Compliances CE Mark Emissions FCC Class A Industry Canada Class A EN55022 (CISPR 22) Class A EN 61000-3-2/3 VCCI Class

  • N ETWORK P L ANNING 3-4 © 2003 Foundry Networks, Inc. February 2003 Application Notes 1. Full-duplex operation only applies to point-to-point access (such as when a switch is attached to a workstation, server or another switch). When the switch is connected to a hub, both devices must operate in half-duplex mode. 2. When a switch is connected to a hub or any kind of shared medi

Related Products and Documents (Switch):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Philips SBA3210/37 Operation & user’s manual philips/sba3210-37-O96.pdf 14 Jul 2022 10 0.55 Mb
2 Sharp CE-150 Service manual sharp/ce-150-7L1.pdf 29 Jan 2024 412
3 Autodesk 22505-051400-9000 - AutoCAD Electrical 2008 Operation & user’s manual autodesk/22505-051400-9000-autocad-electrical-2008-2DF.pdf 09 Jul 2023 1304 4.57 Mb
4 Lenovo ThinkPad G41 Příručka pro základní servis a odstraňování problém lenovo/thinkpad-g41-2C9.pdf 12 Feb 2023 102
5 Bose Acoustimass Owner's manual bose/acoustimass-45Z.pdf 17 Dec 2022 13 1.93 Mb
6 Sony D-263 Service manual sony/d-263-R58.pdf 27 Jan 2023 40

Similar Resources:

  • GE Bluetooth

    13869

    (2 pages)
    MANUAL • MANUEL • MANUALIn-wall WirelessSmart SwitchMontage mural sans filintelligent enfichableInterruptor inalàmbrico de paredinteligenteWhite (Neutral)Green (Ground)Black (Line / Hot)BluetoothSingle SwitchBlack (Load)13869BT4001Scan to view installation guideBalayez ce code pour consulter le guide d’installation. Escanear para ver la guía de in …
  • Louroe Electronics

    SA-1A

    (8 pages)
    DESCRIPTION The SA-1A is a sound activated switch, based on sound pressure level, that can be used with the Louroe ASK-4 #101, any Louroe base station or as a stand alone with any Louroe Microphone. The SA-1A provides an adjustable threshold that activates when the microphone is subjected to a noise or sound that exceeds the set threshold level.The unit …
  • Kramer

    VP-61N

    (16 pages)
    .5$0(5(/(&7521,&6/7' .UDPHU(OHFWURQLFV/WG86(50$18$/9*$;*$$XGLR6ZLWFKHUV0RGHOV93193[O� …
  • Kathrein

    EXD 1532

    (24 pages)
    1 / 12EXD 1532 20510104EXD 2532 20510105Sat-ZF-Verteilsystem (4 x Sat-ZF)Digitaler Einkabel-MultischalterEinkabel-Multischalter zweiter Gene-ration – Digital-Channel-Stacking-Switch (dCSS) mit neuester Full-Band-Capture-TechnologyKaskadierbarer Twin-Multischalter. Für beide Ausgänge sind verschiedene Konfigurationen/Anzahl der User-bänder mittels …
  • Black Box

    KV2008A

    (31 pages)
    ServSwitch Wizard DVI DLUSER GUIDE®NETWORK SERVICES®Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S. call 724-746-5500)FREE technical support 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746Mailing address: Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018Web site: www.blackbox.com • E …
  • Server Technology

    CW-8H

    (2 pages)
    ModelAvailable Input VoltagesOutletsAvailable Input CordAmperageDimensions*(L x W x D)Sentry : Solutions for the Data Center Equipment CabinetKey FeaturesSentry : CDU Technical SpecificationsSentry Switched CDUCW-8HHigh-Density Power DistributionThe Switched CDU’s combine remote configuration and management with power distribution and power and environment …

Comments, Questions and Opinions: