Franklin Chef FIM200 Operation & User’s Manual
|
Franklin Chef FIM200, 8 Location Requirements This ice maker should be installed by qualified personnel. NOTICE: 1. Before setting the ice maker inside a cabinet, connect the water supply pipe correctly. Untie the drain hose, insert it into the drain, and connect the power supply line. 2. Do not kink or pinch the power supply line between the ice maker and wall or cabinet. Installation clearance Top view Side view Installing the stability brackets This operation requires at least two
Franklin Chef FIM200, 9 • When installing the ice maker under a counter, follow the recommended spacing dimensions shown. Allow at least 2/5_ (10 mm) clearance at rear, 1/5” (5 mm) at the sides and 1_ (25 mm) at the top for proper air circulation. The installation should allow the ice maker to be pulled forward for servicing if necessary. • Choose a well-ventilated area with temperatures above 50ºF (10ºC) and below 100ºF (38ºC). This unit MUST be installed in an area protected from the elements, such as wind, rain, water spray or drips. • The unit should not be located next to ovens, grills or other sources of high heat. • Installation of the ice maker requires a cold water supply inlet of
Franklin Chef FIM200, 6 Water supply hose Ice scoop Component Locations Back view Top view Power supply line Drain hose Water inlet Float Water pump Stability brackets Top panel Door Evaporator (ice mold) Ice full probe Water tank Water tank screw nut Ice storage bin Front bottom louver Control panel cover Ad j ustable foot
Franklin Chef FIM200, 5 *The actual quantity of ice produced per day can vary with room and water conditions. The technical data and performance index listed above should be used for reference only. They are subject to change. This product has been tested and certified to NSF standard 12 by NSF International. Introduction The Franklin Chef® FIM200 Ice Cube Machine produces hard, crystal-clear, gourmet cube ice, and offers convenience for homeowners and hotel guests. An insulated ice storage bin is built in. This user’s manual is intended as a resource for persons installing, using and servicing model FIM200. It contains valuable information on safety and ma
Franklin Chef FIM200, 17 d. Slide out the ice storage bin for cleaning and/or servicing. Water Distribution Tube Cleaning When you find that the ice cubes are incompletely formed or the output of ice cubes is low, the water distribution tube may be blocked. Set the power switch to OFF. Unscrew the four screws holding the top panel and remove the panel. You will see the water distribution tube. Rotate the water distribution tube so that the holes in it are facing up. Using a toothpick or similar tool, dredge the holes, then rotate the water distribution tube back to its original position. If the tube is badly blocked, clean it as follows: 1. Shut off the
Franklin Chef FIM200, 1 TECHNICAL INFORMATION .................................................................................. 5 INTRODUCTION ....................................................................................................... 5 COMPONENT LOCATIONS ...............................................................................................................6 ICE MAKER INSTALLATION ..................................................................................................7 - 11 Unpacking ............................................................................................................. 7
Franklin Chef FIM200, 2 ICE MAKER SAFETY Your safety and the safety of others are very important. We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. This is the Safety Alert Symbol. This symbol alerts you to potential hazards that can injure or kill you and others. All safety messages will follow the Safety Alert Symbol and either the words “DANGER”, “WARNING” OR “CAUTION”. DANGER means that failure to heed this safety statement may result in death or severe personal injury. WARNING means that failure to heed
Franklin Chef FIM200, 20 3. Ice Harvest (Yellow) LED: Ice Harvest indicator light When this LED is on, the unit is working in the ice harvest mode controlled by the ice-full probe. 4. I. S. Adjust screw: Ice size adjustment Turn the screw clockwise and the size of individual ice cubes will be larger in the next cycle; the cycle time will be longer. Turn the screw counter-clockwise, and the ice cube size will be smaller in the next cycle. 5. Power switch This is the main switch. When it is turned on, the unit goes into Stand-by mode for about 3 minutes, with all LEDs on, then starts to make ice cub
Franklin Chef FIM200, 7 Ice Maker Installation Unpacking Remove packaging materials IMPORTANT: Do not remove any permanent instruction labels or the data label on your ice maker. Remove tape and glue from your ice maker before using, • To remove any remaining tape or glue, rub the area briskly with your thumb. Tape or glue residue can also be easily removed by rubbing a small amount of liquid dish soap over the adhesive with your fingers. Wipe with warm water and dry. • Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners to remove t
11 remove the nut. 4. Connect nuts of the water supply hose to tap and water inlet valve. Tighten firmly by hand, then one-half turn with wrench. 5. Turn on main water supply and tap. Check for water supply connection leaks. Tighten every connection (including connections at the water inlet). Installation Types This ice cube machine has been designed to be enclosed (as under a cabinet). I
18 7. Re-attach the top panel. Ice-Making System Cleaning Minerals that are removed from water during the freezing cycle will eventually form a hard, scaly deposit in the water system. Cleaning the system regularly helps remove the mineral scale buildup. How often you need to clean the system depends on how hard your water is or how effective your filtration may be. With hard water of 15 to 20 g
Franklin Chef FIM200, 4 material safety instructions on the container of the ice machine cleaner. • Do not use this apparatus for other than its intended purpose. SAVE THESE INSTRUCTIONS Electrical Connection Do not, under any circumstances, cut or remove the third (ground) prong from the power cord. For personal safety, this appliance must be properly grounded. The power cord of this appliance is equipped with a 3-prong grounding plug that mates with a standard 3-prong grounding wall outlet to minimize the possibility of electric shock hazard from the appliance. Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet
21 Troubleshooting Before Calling for Service If the unit appears to be malfunctioning, read through the OPERATION section of this manual first. If the problem persists, check the Troubleshooting Guide below and on the following page. The problem may be something very simple that can be solved without a service call. ON. air screen.
Franklin Chef FIM200, Ice Cube Machine User’s Manual Franklin Industries, LLC Model FIM200 4100 First Avenue Brooklyn, NY 11232-3321 Tel.: 1-888-424-8278 E-mail: [email protected] TABLE OF CONTENTS Page ICE MAKER SAFETY ................................................................................................ 2 IMPORTANT SAFEGUARDS ..............................................................................2 – 4 MAJOR FEATURES ................................................................................................... 4 ® Be sure the ice
Franklin Chef FIM200, 3 • Plug into a grounded 3-prong outlet. Do not remove grounding prong, do not use an adapter, and do not use an extension cord. • It is recommended that a separate circuit, serving only your ice maker, be provided. Use receptacles that cannot be turned off by a switch or pull chain. • Do not connect or disconnect the electric plug when your hands are wet. • Never unplug the ice maker by pulling on the power cord. Always grip the plug firmly and pull straight out from the outlet. • Never clean ice maker parts with flammable fluids. Do not store or use gasoline or other f
Franklin Chef FIM200, 15 with a clean cloth. To clean hard-to-reach corners, apply the sanitizing solution with a spray bottle. 4. Rinse thoroughly with clear water. This completes the routine interior cleaning of the unit. 5. Reconnect the power. The ice scoop should be washed regularly. Wash it just like any other food container. For a more thorough cleaning of the interior, the ice storage bin must be removed. This will allow cleaning of the vertical channels on both sides of the evaporator (ice mold) and the sides of the ice storage bin that are not normally accessible. Wipe these surfaces with the sanitizing solution. To remove the ic
Franklin Chef FIM200, 24 Limited Warranty Franklin Industries, LLC, warrants this product to be free from defects in materials and workmanship for a period of one year from the date of the original purchase or delivery. Any parts that are determined to be defective will be replaced or repaired, at its sole discretion, by Franklin Industries, L.L.C., at no charge as long as it has been determined that the unit was operated in accordance with the instructions attached or furnished with the product. If the unit proves to be defective, your first course of action should be to follow the retailer’s return policy. This warranty covers units only in the continental United States and
Franklin Chef FIM200, 13 The ice cube machine begins with a fixed charge of water that is contained in the water tank. As the water flows to the freezing evaporator surface, the water will freeze and stick to the ice cube molds. During the ice-making process, fresh water enters the water tank continuously as the water from the trough freezes continuously on the evaporator. Normal Sounds Your new ice cube machine may make sounds that are unfamiliar to you. Most of the new sounds are normal. Hard surfaces like the floor and walls can amplify the sounds. The following describes the kinds of sounds that might
Franklin Chef FIM200, 12 11. Have you checked for leaks at all water supply connections? Operating Method 1. Turn on the water tap, letting the water enter the water tank, then turn the power switch ON. The power switch’s indicator lamp lights, as well as the other three indicator lights on the control panel. 2. After about 3 minutes, the ice maker will automatically proceed to the ice-making stage, and the sound of flowing water will be heard. Only the red power switch lamp and the green Ice Making LED will be on. 3. When the batch of ice ha
Franklin Chef FIM200, 16 2. Remove the ice storage bin a. After removing the bottom louver, look for two screws under the slide way (see illustration). Unscrew the two screws. b. Unscrew and remove the top panel. c. Remove the drain hose at the back of the machine by unscrewing the hose connector.
10 Recommended grounding method For your personal safety, this appliance must be grounded. It is equipped with a power supply cord having a 3-prong grounding plug. To minimize possible shock hazard, the cord must be plugged into a mating 3-pronged and grounding-type wall receptacle, grounded in accordance with the National Electrical Code and local codes and ordinances. If a m
DOWNLOAD |
Franklin Chef FIM1000 Ice Maker Specifications
FIM1000 |
Franklin Chef FB400 Ice Maker User instructions
FB400 |
Franklin Chef FIM200 Ice Maker Specifications
FIM200 |
Franklin Chef FIM70 Ice Maker Operation & user’s manual
FIM70 |
ALPATEC MG 1 Ice Maker Manual
MG 1 |
Franklin Chef FIM1000 Ice Maker Operation & user’s manual
FIM1000 |
Franklin Chef FIM120 Ice Maker Operation & user’s manual
FIM120 |
Sub-Zero UC-15I Ice Maker Specification sheet
UC-15I |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | Grindmaster | Crathco | Operator's manual | grindmaster/crathco-C3R.pdf | 17 Feb 2024 | 12 | 0.49 Mb |
2 | Kuppersbusch | EEB 9600.5 | User manual manual | kuppersbusch/eeb-96005-8LT.pdf | 23 Jan 2024 | 17 | |
3 | Aiwa | NSX-SZ50 | Service manual | aiwa/nsx-sz50-2U9.pdf | 05 Jul 2023 | 35 | 11.79 Mb |
4 | ASROCK | X58 Extreme3 | Installation manual | asrock/x58-extreme3-B94.pdf | 09 Dec 2023 | 227 | 6.01 Mb |
5 | M-Audio | SP-8B Studiophile Series | Operation & user’s manual | m-audio/sp-8b-studiophile-series-P44.pdf | 11 Mar 2024 | 12 | |
6 | Electrolux | EW28BS70IS - Refrigerator With Wave-Touch Controls | Specifications | electrolux/ew28bs70is-refrigerator-with-wave-touch-controls-QQV.pdf | 01 Jun 2023 | 2 |
Mellerware
Register onlineNever lose your receipteNemakes life easierICE MASTERblack icemaker, Model:100WICM001BKABullet shaped ice cubesProduction capacity: 12kg/24HrsViewing window_IM.indd 1 5/22/2014 3:57:32 PM
…
ICE MASTER ICM001BKA(6 pages) |
Steba
www.steba.com 220 – 240 V~; 50 Hz; 7,3 – 9,5 WEismaschine IC 30 Gebrauchsanweisung 2 Instructions for use 10 Mode d´emploi 17 Gebruiksaanwijzing 25 Brugsanvisning 33
…
IC 30(42 pages) |
Hoshizaki
• Up to 235 lbs. of ice production per 24 hours• Built-in 120 lbs. ice storage• Individual crescent cube• Protected by HoshiGuard Antimicrobial Agent• CycleSaver®Design• EverCheck®alert system• Stainless steel evaporator• Corrosion-resistant stainless exterior surfaces provide longer life• Removable air filter• Complies with California …
KM-255BAH(2 pages) |
Cornelius
CONTINUOUS FLOW ICEMAKERWCC 2001 QT - RService ManualRelease Date: September 21, 2005Publication Number: 630460308SERRevision Date: March 18, 2014Revision: GVisit the Cornelius web site at www.cornelius.com for all your Literature needs.
…
WCC 2001 QT-R(24 pages) |
Franklin Chef
0 Automatic Commercial Ice Cube Machine Máquina de hielo comercial automática Machine à glaçons automatique commerciale User’s Manual / Manual del usuario / Manuel de l’utilisateur00 Franklin Industries, LLC Models/Modelos/Modèles 4100 First Avenue …
FIM1000(72 pages) |
Manitowoc
K00106 ADAPTER KIT Installation Instructions 1. The K00106 adapter kit is used for installing a B-0320 or B-0420 ice machine on a Manitowoc 30” wide series dispenser. 2. Installation (dispenser to be level before starting): A. Place adapters on dispenser, as …
K00106(1 pages) |
Olympus Racks & Stands Handy copy standRacks & Stands Instructions (Olympus Handy copy stand) Handy copy stand, 1 |
SBC Caller ID Box SBC-40SBC SBC-40 User Manual (Doc Type: Caller ID Box Operation & user’s manual) SBC-40, 1 |
GeoRecord Dash Cameras FCD-01GeoRecord Dash Cameras Operation & user’s manual (File: georecord-fcd-01-operation-user-s-manual-14, Sunday 31-12-2023) FCD-01, 14 |
Hico Medical Systems Medical Equipment HICO-VARIOTHERM 550Medical Equipment #3AMJ3T HICO-VARIOTHERM 550, 73 |
Panasonic Computer Hardware TY-FB10HDPanasonic Product User Guide: TY-FB10HD PDF Service manual - 344E6O TY-FB10HD, 23 |
Sharp Microwave Oven R-7N76(B)M#I55K6L R-7N76(B)M: Sharp Microwave Oven Owner Documentation R-7N76(B)M, 49 |
Daewoo Microwave Oven KOR-6Q6RPDF User Guide (@G96YF5), Daewoo KOR-6Q6R Microwave Oven (Tue 12.2023) KOR-6Q6R, 29 |
Mitsubishi Electric Air Conditioner PUHZ-RP8YHAPDF Guide (@PQ8U8F), Mitsubishi Electric PUHZ-RP8YHA Air Conditioner (Fri 09.2023) PUHZ-RP8YHA, 86 |
Avaya Server G700Server Quick start manual (Avaya G700) G700, 32 |
Jøtul Wood stove F 100 NordicInstallation instructions with technical data for Jøtul F 100 Nordic Wood stove F 100 Nordic, 48 |
Yaesu Transceiver FT2DRYaesu FT2DR Manual (Instruction manual), @9VZ748 FT2DR, 80 |
Sharp LCD TV LC26D43U - 26" LCD TVSharp LC26D43U - 26" LCD TV LCD TV Service manual LC26D43U - 26" LCD TV, 116 |