Manualios.com

Schumacher 120V Operation & User’s Manual

Schumacher 120V Manual Online:

3.15, 1127 votes
Schumacher 120V User Manual
Schumacher 120V User Guide
Schumacher 120V Online Manual

Text of Schumacher 120V User Guide:

  • Schumacher 120V, SAFETY INFORMATION The following safety information is provided as a guideline to help you operate your new cutter under the safest possible conditions. Any equipment that uses electrical power can be potentially dangerous to use when safety or safe handling instructions are not known or not followed. The following safety information is provided to give you the information necessary for safe use and operation. When a WARNING precedes a procedure step, it is an indication that the step contains a procedure that might be injurious to a person if proper safety precautions are not heeded. When a procedure step is preceded by a CAUTION, it is an indication that the step contains a proce

  • Schumacher 120V, • Do not modify any wiring, ground connections, switches, or fuses in this cutting equipment. • Wear welding gloves to help insulate hands from welding circuit. • Keep all liquid containers far enough away from the cutter and work area so that if spilled, the liquid can not possibly come in contact with any part of the cutter or electrical welding circuit. • Replace any cracked or damaged parts that are insulated or act as insulators such as cables, power cord, or torch IMMEDIATELY. EMF INFORMATION WARNING Cutting cur

  • Schumacher 120V, FIRE HAZARDS WARNING FIRE OR EXPLOSION CAN CAUSE DEATH, INJURY, AND PROPERTY DAMAGE! To reduce risk of death, injury, or property damage from fire or explosion, read, understand, and follow the following safety instructions. In addition, make certain that anyone else that uses this cutting equipment, or is a bystander in the cutting area, understands and follows these safety instructions as well. REMEMBER! Plasma arc cutting by nature produces sparks, hot spatter, molten metal drops, hot slag, and hot metal parts that

  • Schumacher 120V, in ANSI standard #Z49.1. If ventilation is not adequate to exchange all fumes and gasses generated during the cutting process with fresh air, do not cut unless you and all bystanders are wearing air-supplied respirators. • Do not heat or cut metals coated with, or that contain, materials that produce toxic fumes (such as galvanized steel), unless the coating is removed. Make certain the area is well ventilated, and the operator and all bystanders are wearing air-supplied respirators. • Do not weld, cut, or heat lead, zinc, cadmium, mercury, beryllium, or similar metals wi

  • NOISE HAZARDS WARNING PLASMA ARC CUTTING NOISE CAN DAMAGE HEARING! To reduce the risk of hearing loss from plasma arc cutting noise, read, understand and follow the following safety instructions. In addition, make certain that anyone else that uses this cutting equipment, or is a bystander in the cutting area, understands and follows these safety instructions as well.

  • Schumacher 120V, SOMMAIRE DES CONSIGNES DE SÉCURITÉ Les consignes de sécurité suivantes vous sont fournies à titre de lignes directrices pour vous aider à utiliser votre nouvelle découpeuse de la manière la plus sure qui soit. Tous les appareils fonctionnant à l’électricité peuvent être dangereux si la personne qui les utilize ignore ou n’observe pas les consignes de sécurité. Les paragraphes suivants contiennent les informations nécessaires pour utiliser la machine en toute sécurité. Une étape précédée du terme AVERTISSEMENT indique q

  • Schumacher 120V, INFORMATION SUR LES CHAMPS ÉLECTROMAGNÉTIQUES AVERTISSEMENT Le courant de soudage, pendant son passage dans les câbles de soudage, causera des champs électromagnétiques. Il y a eu et il y a encore un certain souci à propos de tels champs. En attendant que les conclusions finales de la recherche soient établies, il vous serait souhaitable de réduire votre exposition aux champs électromagnétiques pendant le soudage ou le coupage. Afin de réduire les champs électromagnétiques dans l’environnement de travail, respecter les consignes suivante

  • Schumacher 120V, RISQUES D’INCENDIE AVERTISSEMENT LES INCENDIES OU LES EXPLOSIONS PEUVENT ETRE MORTELS, PROVOQUER DES BLESSURES CORPORELLES, ET CAUSER DES DOMMAGES MATÉRIELS! Afin de réduire les risques d’accidents mortels, de blessures corporelles et de dégâts matériels causés par un incendie ou une explosion, veuillez lire, comprendre et observer ces consignes de sécurité. De plus, assurez-vous que toute personne susceptible d’utiliser cette machine ou de se tenir dans l’aire de découpe comprend et observe également ces consignes de sécurité. SOUVENEZ-VOUS que par nature, la découpe au plasma s’accompagne d’étincelles, de projections br�

  • Schumacher 120V, • Couvrez les murs, les plafonds et les sols constitutes de matériaux inflammables avec des couvertures ou protections résistantes à la chaleur. • Inspectez l’aire de découpe afin de vous assurer qu’elle ne présente ni étincelles, ni métal ou scories en fusion, ni flammes avant de vous en éloigner. RISQUES DE FUMÉES TOXIQUES AVERTISSEMENT LES FUMÉS, LES GAZ, ET LES VAPEURS PEUVENT VOUS INCOMMODER, VOUS RENDRE MALADE, OU VOUS TUER! Afin de réduire les risques de malaises, de m

  • Schumacher 120V, • N’exposez pas les bouteilles à une chaleur excessive, des étincelles, des particules en fusion, des flammes, etc. Les bouteilles de gaz soumises à une temperature supérieure à 130°F (55°C) doivent être refroidies par vaporisation d’eau. • N’exposez pas les bouteilles à une forme d’électricité quelle qu’elle soit. • N’utilisez pas une bouteille ou son contenu dans un but autre que celui prévu. Ne l’employez pas comme support ou rouleau. • N’entreposez pas les bouteilles de gaz dans un passage ou dans une zone de travail où e

  • Schumacher 120V, RISQUES DE PERTE AUDITIVE AVERTISSEMENT LE BRUIT RÉSULTANT DE LA DÉCOUPE AU PLASMA PEUT CAUSER UNE PERTE AUDITIVE ! Afin de réduire les risques de surdité à la suite de la découpe au plasma, lisez attentivement les consignes de sécurité suivantes pour bien les comprendre et observez-les. De plus, assurez-vous que toute autre personne susceptible d’utiliser cette machine ou de se tenir dans l’aire de découpe comprend et observe également ces consignes de sécurité. • Portez une protection auditive conforme ou supérieure aux normes de sécurité de l’OSHA pendant la découpe. CONSIGNES DE SÉCURITÉ SUPPLÉMENTAIRES Pour toutes informations complémentaires

  • Schumacher 120V, INTRODUCTION DESCRIPTION Your new plasma arc cutter has been designed to cut any electrically conductive material in applications such as maintenance shops, service stations, van conversion shops, auto restoration and salvage operations, etc. On steel, all models can cut thicknesses of less than 26 gauge but the 120V model can cut up to 5/16” inch steel, and the 230V model can cut up to 3/8” inch steel. Your plasma arc cutter comes complete and ready to cut. All you need to provide is a clean, dry, oil free compressed air supply. The system is based on a modern DC inverter power supply

  • WARNING ELECTRIC SHOCK CAN KILL! FIRE CAN KILL, INJURE, AND CAUSE PROPERTY DAMAGE! • To reduce the risk of electric shock and fire, connect only to properly grounded and fused outlets. • Never alter the AC power cord provided on the welder. Never alter an extension cord or extension cord plugs. EXTENSION CORD USE For optimum welder performance, an extensi

  • Schumacher 120V, CONTROLS & THEIR FUNCTIONS 1. POWER OUTPUT INDICATOR When lit, this LED indicates that power is available for cutting. 2. ALARM INDICATOR When lit, this LED indicates that one of the alarms has triggered. At the same time the digital display (Ref. 3) shows the type of alarm, as shown in the table below, with instructions\for correcting the problem. In this condition the unit does not supply current. 3. DIGITAL DISPLAY This display operates in a number of ways: Display Volts or Amps – by pressing the V/A switch (5), you can read the voltage or amperage at the torch. This is a momentary

  • Schumacher 120V, DISPLAY ERROR or PROBLEM CORRECTION/RESET LHF Inverter error/malfunction Turn the unit OFF and then ON again. If this condition persists, contact Technical Service 4. Digital Display Function LED This LED indicates what function the digital display is indicating – Volts, Amps, or Air Pressure (bar) 5. V/A Button By pressing this button, the digital display will indicate Volts or Amps. The display will stay on for a few seconds and then shut off. 6. Air Button (bar) By pressing this button, the air circuit will open and allow adjustment of the air pressure at the

  • Schumacher 120V, PLASMA TORCH CONSUMABLE PARTS During the cutting process, the parts on the end of the torch are slowly consumed. To prevent premature consumption of some torch parts and to prevent damage to the torch itself, it is necessary to replace the consumable parts in a timely manner. When the cutting arc seems to be weaker than normal or sputters, inspect all torch consumables for wear and damage and replace as needed. Standard Electrode (03) Long Electrode – optional 04) Air Diffuser (05) Standard Nozzle (07) Long Nozzle – optional (08) Nozzle Cap (10) Wire Standoff (11) Roll

  • Schumacher 120V, CONNECT WELDER GROUND Attach the ground clamp to the work piece making sure that the work piece is cleaned of dirt, oil, rust, scale, oxidation, and paint at the point of connection. It is best to connect the ground clamp directly to the work piece and as close to the cut as possible. If it is impractical to connect the ground clamp directly to the work piece, connect it to metal that is securely attached to the work piece, but not electrically insulated from it. It is possible to cut ungrounded pieces, but cutting capacity is limited and consumable life is decreased. CAUTION! RISK OF ELECTRONIC COMPONENT DAMAGE! If the ground clamp is being connected to an a

  • Schumacher 120V, TROUBLESHOOTING The following TROUBLESHOOTING information and tables are provided as a guide to help resolve some of the more common problems that could be encountered. Should you or qualified repair personnel be unable to resolve a problem or determine which of the possible solutions will remedy a specific problem, contact WELDER SERVICE for over-the-phone diagnostic assistance at: (800) 458- 6447. FRONT PANEL – TROUBLESHOOTING ERROR CODES In some cases, error codes may appear on the digital display. The table below indicates the type of error. Record these error codes w

  • Schumacher 120V, Reference Number Part Number 120 Volt Models Part Number 230 Volt Models Description 01 9807600546 9807600543 CIRCUIT BOARD CE 22662 08 POWER CORD 09 9807600400 9807600400 POWER CORD STRAIN RELIEF 10 9807600398 9807600398 MOUNTING BLOCK 11 9807600433 9807600433 SWITCH 13 9807600408 9807600408 KNOB 14 9807600495 9807600495 FAN ASSEMBLY 30 92500 92500 TORCH ASSEMBLY 31 9807600525 9807600525 GROUND CABLE 36 9807600546 9807600546 CIRCUIT BOARD CE 22666 38 9807600592 9807600592 PLASTIC TRIM 46 9

  • Reference Number Part Number Description 01 9807600519 TORCH BODY 03 92503 ELECTRODE STANDARD 04 92504 ELECTRODE EXTENDED (opt.) 05 92505 AIR DIFFUSER 07 92501 NOZZLE STANDARD 08 92502 NOZZLE EXTENDED (opt.) 09 92506 NOZZLE CAP 10 92507 WIRE STANDOFF 11 92508 TORCH ROLLER STANDOFF (opt.) 22

  • Schumacher 120V, MANUFACTURER’S LIMITED WARRANTY The manufacturer warrants that it will repair, at no charge for parts or labor, the Plasma Cutter or components, proven defective in material or workmanship, during the following time period(s) after date of original retail purchase: For 5 Years: The Plasma Cutter’s switch, solenoid valve and air pressure switch only For 2 Years: The Entire Plasma Cutter including main circuit boards(excluding accessories packed with the plasma cutter) For 1 Year: The Plasma cutter’s Welding Cables and Cutting Torch If after reasonable efforts by the manufacturer, the Plasma cutter or component(s) is/ar

Related Products and Documents (Cutter):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Sanyo KR-7000F Specifications sanyo/kr-7000f-8C1.pdf 23 Nov 2023 1 0.14 Mb
2 DeWalt DW086-XE Instruction manual dewalt/dw086-xe-63T.pdf 22 Jul 2022 12 0.63 Mb
3 Cub Cadet M466 Operator's manual cub-cadet/m466-SDY.pdf 18 Nov 2023 28 1.25 Mb
4 RCA RP4806 Operation & user’s manual rca/rp4806-P72.pdf 30 Jun 2023 1 0.04 Mb
5 Gefen EXT-HDMI-444 Operation & user’s manual gefen/ext-hdmi-444-LZW.pdf 24 Dec 2023 14 0.15 Mb
6 GB Instruments GDT-190A Owner's manual gb-instruments/gdt-190a-39Q.pdf 16 Feb 2024 22 0.29 Mb

Similar Resources:

  • ESAB

    PT-27

    (16 pages)
    PT-27PLASMA ARC CUTTING TORCHINSTRUCTION MANUALThis manual provides installation and operation instructions for the following PT-27 torches:P/N 21620 - 25 ft (7.6 m), PT-27, w/PLUG Pilot Arc ConnectionP/N 21621 - 50 ft (15.2 m), PT-27, w/PLUG Pilot Arc ConnectionP/N 21661 - 25 ft (7.6 m), PT-27, w/RING Pilot Arc ConnectionP/N 21662 - 50 ft (15.2 m), PT-27, w …
  • JMA

    VOLGA BIT

    (61 pages)
    VOLGA BITwww.jma.esMÁQUINA DUPLICADORA MANUAL DE INSTRUCCIONESKEY CUTTING MACHINEMUSER MANUALSCHLÜSSELKOPIERFRÄSE ANWEISUNGSHANDBUCHMACHINE A REPRODUIRE MANUEL D’INSTRUCTIONSMÁQUINA DUPLICADORA MANUAL DE INSTRUÇÕESMASZYNA DO KOPIOWANIA …
  • Chocolate World

    M1920

    (17 pages)
    Chocolate World User and maintenance manual Semi-automatic cutters Page 1 of 17 USER AND MAINTENANCE MANUAL for the M1920 - M1921 M1922 - M1923 SEMI-AUTOMATIC CUTTERS CHOCOLATE WORLD Lange Elzenstraat 123 • 2018 Antwerpen - Belgium Phone +32 (0)3 216 44 27 • Fax +32 (0)3 216 98 33 [email protected] • www.chocolateworld.be …
  • Toro

    Greensmaster 3250-D

    (52 pages)
    FormNo.3422-517RevAGreensmaster®3250-D2-WheelDriveTractionUnitModelNo.04384—SerialNo.401380001andUpRegisteratwww.Toro.com.OriginalInstructions(EN)*3422-517*A …
  • Challenge

    Spartan 185 SA

    (22 pages)
    F.185SA-O January 2014 SPARTAN 185 SA Operator’s Manual Serial Numbers 051001 & Up Sold and Serviced by The Challenge Machinery Company 6125 Norton Center Drive Norton Shores, MI 49441-6081 USA ChallengeMachinery.com The Challenge Machinery Company provide …
  • REMS

    Amigo

    (148 pages)
    REMS AmigoREMS Amigo EREMS Amigo 2REMS Amigo 2 CompactREMS Akku-Amigo 22 Vfor ProfessionalsREMS GmbH & Co KGMaschinen- und WerkzeugfabrikStuttgarter Straße 8371332 WaiblingenDeutschlandTelefon +49 7151 1707-0Telefax +49 7151 1707-110www.rems.dedeu Betriebsanleitung ...............................................4eng Instruction Manual ................. …

Comments, Questions and Opinions: