Fujitsu ASTA18LCC Operating Manual
|
Fujitsu ASTA18LCC, KEEP THIS OPERATION MANUAL FOR FUTURE REFERENCE FUJITSU GENERAL LIMITED OPERATING MANUAL P/N9315161024-01 Indoor Unit ASTA18LCC Outdoor Unit AOTR18LCC HEAT & COOL MODEL (REVERSE CYCLE) ROOM AIR CONDITIONER WALL MOUNTED TYPE R410A REFRIGERANT This Air Conditioner contains and operates with refrigerant R410A and Polyol Ester oil. THIS PRODUCT MUST ONLY BE INSTALLED OR SERVICED BY QUALIFIED PERSONNEL. Refer to Commonwealth, State, Territory and local legislation, regulations, codes, installation & operation manuals, before the installation, maintenance and/or service of this product
Fujitsu ASTA18LCC, 1 CONTENTS SAFETY PRECAUTIONS .......................................... 1 FEATURES AND FUNCTIONS ................................. 2 NAME OF PARTS ...................................................... 3 PREPARATION .......................................................... 5 OPERATION .............................................................. 6 TIMER OPERATION .................................................. 8 SLEEP TIMER OPERATION ...................................... 9 ADJUSTING THE DIRE
Fujitsu ASTA18LCC, 2 FEATURES AND FUNCTIONS INVERTER At the start of operation, a large power is used to bring the room quickly to the desired temperature. Afterwards, the unit automatically switches to a low power setting for eco- nomic and comfortable operation. COIL DRY OPERATION The Indoor unit can be dried by pressing the COIL DRY but- ton on the Remote Control Unit so as to avoid going moldy and restrain the breed of bacterium. AUTO CHANGEOVER The operation mode (cooling, dry, heating) is switched au- tomatically to maintain the set temperature, and the tem- perature is kept constant at all times. PROGRAM TIMER The program timer allows you to integrate OFF timer and ON timer operatio
Fujitsu ASTA18LCC, 3 5 6 4 7 8 OPERATION TIMER SUPER QUIET COIL DRY A B C 2 G 9 1 = 3 D F E H I K J 9 3 1 NAME OF PARTS Fig. 5 Fig. 1 Fig. 2 Fig. 3 Fig. 4 Fig. 6 P [ b ] a S T M O L Q Y N U V W R X c d ^ \ e Z Fig. 7 To facilitate explanation, the accompanying illustra- tion has been drawn to show all possible indicators; in actral operation, however, the display will only show those indicators appropriate to the current op- eration.
Fujitsu ASTA18LCC, 4 NAME OF PARTS Fig. 1 Indoor Unit 1 Operating Control Panel (Fig. 2) 2 MANUAL AUTO button ● When kept on pressing the MANUAL AUTO button for more than 10 seconds, the forced cooling operation will start. ● The forced cooling operation is used at the time of installation. Only for authorized service personnel's use. ● When the forced cooling operation starts by any chance, press the START/STOP but- ton to stop the operation. 3 Indicator (Fig. 3) 4 Remote Control Signal Receiver 5 OPERATION Indicator Lamp (red) 6 TIMER Indicator Lamp (green) ● If the TIMER indicator lamp flashes when the timer is operating, it indicates that a fault has occurred with the time
Fujitsu ASTA18LCC, 5 PREPARATION CAUTION! ● Take care to prevent infants from accidentally swallowing batteries. ● When not using the Remote Control Unit for an extended period, remove the batteries to avoid possible leakage and damage to the unit. ● If leaking battery fluid comes in contact with your skin, eyes, or mouth, immedi- ately wash with copious amounts of water, and consult your physician. ● Dead batteries should be removed immediately and disposed of properly, either in a battery collection receptacle or to the appropriate authority. ● Do not attempt to recharge dry batteries. Never mix
6 OPERATION To Select Mode Operation 1 Press the START/STOP button (Fig.6 T). The indoor unit’s OPERATION Indicator Lamp (red) (Fig. 3 5) will light. The air conditioner will start operating. 2 Press the MASTER CONTROL button (Fig.6 M) to se- lect the desired mode. Each time the button is pressed, the mode will change in the following order. AUTO COOL DRY HEAT FAN About three sec
7 To Stop Operation Press the START/STOP button (Fig. 6 T). The OPERATION Indicator Lamp (red) (Fig. 3 5) will go out. About AUTO CHANGEOVER Operation AUTO: ● When AUTO CHANGEOVER operation first selected, the fan will oper- ate at very low speed for about one minute, during which time the unit detects the room conditions and selects the proper operating mode. If the differance between thermo
Fujitsu ASTA18LCC, 8 TIMER OPERATION s Before using the timer function, be sure that the Remote Control Unit is set to the correct current time (☞ P. 5). To Use the ON timer or OFF timer 1 Press the START/STOP button (Fig. 6 T) (if the unit is already operating, proceed to step 2). The indoor unit’s OPERATION Indicator Lamp (red) (Fig. 3 5 ) will light. 2 Press the TIMER MODE button (Fig. 6 Q) to select the OFF timer or ON timer operation. Each time the button is pressed the timer function changes in the follow- ing order: CANCEL OFF ON PROGRAM(OFF → ON, OFF ← ON) The indoor unit’s TIMER Indicator Lamp (green) (Fig. 3 6) will light. 3 Use the TIMER SET buttons (Fig. 6 R) to adjust th
Fujitsu ASTA18LCC, 9 SLEEP TIMER OPERATION Unlike other timer functions, the SLEEP timer is used to set the length of time until air conditioner operate is stopped. To Use the SLEEP Timer While the air conditioner is operating or stopped, press the SLEEP button (Fig. 6 L). The indoor unit’s OPERATION Indicator Lamp (red) (Fig. 3 5) lights and the TIMER Indicator Lamp (green) (Fig. 3 6) light. To Change the Timer Settings Press the SLEEP button (Fig. 6 L) once again and set the time using the TIMER SET ( / ) buttons (Fig. 6 R). Set the time while the Timer Mode Display is flashing (the flashing will continue about five seconds). bu
Fujitsu ASTA18LCC, 10 ADJUSTING THE DIRECTION OF AIR CIRCULATION Vertical (up-down) direction of airflow is adjusted by pressing the Remote Control Unit’s SET button. Horizontal (right-left) airflow direction is adjusted manually, by moving the Air Flow Direction Louvers. Whenever making horizontal airflow adjustments, start air conditioner operation and be sure that the vertical air direction louvers are stopped. R DANGER! ● Never place fingers or foreign objects in- side the outlet ports, since the internal fan operates at high speed and could cause personal injury. ● Always use the Remote Control Unit’s SET bu
Fujitsu ASTA18LCC, 11 SWING OPERATION MANUAL AUTO OPERATION Use the MANUAL AUTO operation in the event the Remote Control Unit is lost or otherwise unavailable. How To Use the Main Unit Controls Press the MANUAL AUTO button (Fig. 2 2) on the main unit control panel. To stop operation, press the MANUAL AUTO button (Fig. 2 2) once again. (Controls are located inside the Open Panel) ● When the air conditioner is operated with the controls on the Main Unit, it will operate under the same mode as the AUTO mode selected on the Re- mote Control Unit (see page 7). �
12 1 2 CLEANING AND CARE ● Before cleaning the air conditioner, be sure to turn it off and disconnect the Power Supply Cord. ● Be sure the Intake Grille (Fig. 1 9) is installed securely. ● When removing and replacing the air filters, be sure not to touch the heat exchanger, as per- sonal injury may result. CAUTION! Cleaning the Intake Grille 1. Remove the Intake Grille. 1 Plac
Fujitsu ASTA18LCC, 13 Air Cleaning Filter Installation 1. Open the Intake Grille and remove the Air filters. 2. Install the Air cleaning filter set (set of 2). 1 Set the air cleaning filter into the air cleaning filter frame. 2 Engage the latch at both ends of the filter with the two hooks at the rear of the air cleaning filter frame. Take care that the air cleaning filter does not project be- yond the frame. 3 Engage the four fixing locations at the top and bot- tom of the air cleaning filter frame with the hooks of the air
Fujitsu ASTA18LCC, 14 TROUBLESHOOTING WARNING! Symptom Doesn’t operate immedi- ately: Noise is heard: Smells: Mist or steam are emitted: Airflow is weak or stops: Water is produced from the outdoor unit: Problem ● If the unit is stopped and then immediately started again, the com- pressor will not operate for about 3 minutes, in order to prevent fuse blowouts. ● Whenever the Power Supply Plug is disconnected and then re- connected to a power outlet, the protection circuit will operate for about 3 minutes, preventing unit operation during that period. ● During operation and immediately after stopping the unit, the sound of water flowing in the air c
Fujitsu ASTA18LCC, 15 TROUBLESHOOTING Symptom Doesn’t operate at all: Poor Cooling performance: The unit operates differently from the Remote Control Unit’s setting: See Page — 8 - 9 — 6 5 CHECK ONCE MORE Items to check ● Is the Power Supply Plug disconnected its outlet? ● Has there been a power failure? ● Has a fuse blown out, or a circuit breaker been tripped? ● Is the timer operating? ● Is the Air Filter dirty? ● Air the air conditioner’s intake grille or outlet port blocked? ● Did you adjust the room temperature settings (thermostat) cor- rectly? ● Is there a window or
Fujitsu ASTA18LCC, 16 OPERATING TIPS Dry Mode About -10 to 43 °C About 18 to 32 °C Outdoor temperature Indoor temperature Cooling Mode About -10 to 43 °C About 18 to 32 °C Heating Mode About –15 to 24 °C About 30 °C or less Temperature and Humidity Range ● If the air conditioner is used under higher temperature conditioner than those listed, the built-in protection circuit may operate to prevent internal circuit damage. Also, during Cooling and Dry modes, if the unit is used under conditions of lower temperature than those listed above, the heat-exchanger may freeze, leading to water leakage and other damage. �
DOWNLOAD |
Fujitsu ARXB07L Air Conditioner Operating manual
ARXB07L |
Fujitsu ABYA45LAT Air Conditioner Service manual
ABYA45LAT |
Fujitsu AB*G24LVTA Series Air Conditioner Installation/troubleshooting manual
AB*G24LVTA Series |
Fujitsu AST9RSHCW Air Conditioner Operating manual
AST9RSHCW |
Fujitsu ASU9RLF1 Air Conditioner Operating manual
ASU9RLF1 |
Fujitsu AUT Series Air Conditioner Operating manual
AUT Series |
Fujitsu ASU9R1 Air Conditioner Operating manual
ASU9R1 |
Fujitsu ASU-RLF Air Conditioner Disassembly instructions manual
ASU-RLF |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | IDEAL | Concord CXSi 110 | Installation & service manual | ideal/concord-cxsi-110-5IU.pdf | 16 Jul 2023 | 36 | |
2 | Vitek | VT-3585 | Manual instruction | vitek/vt-3585-ZCV.pdf | 20 Nov 2022 | 6 | 0.15 Mb |
3 | Gigabyte | 6CX | Operation & user’s manual | gigabyte/6cx-WPI.pdf | 11 Sep 2022 | 94 | 0.95 Mb |
4 | Polaroid | PLA-4260MTR | Operation manual | polaroid/pla-4260mtr-82U.pdf | 20 Jul 2023 | 22 | |
5 | Samsung | SGH-F406 | Operation & user’s manual | samsung/sgh-f406-582.pdf | 01 Nov 2023 | 211 | |
6 | Blu | TANK | Operation & user’s manual | blu/tank-Q5J.pdf | 02 Dec 2023 | 11 | 0.48 Mb |
Olimpia splendid
PELER 4EISTRUZIONI PER USO E MANUTENZIONE INSTRUCTION FOR USE AND MAINTENANCEMODE D'EMPLOI ET D'ENTRETIENHINWEISE FÜR DIE VERWENDUNG UND PFLEGEINSTRUCCIONES PARA EL USO Y EL MANTENIMIENTO
…
PELER 4E(52 pages) |
Soleus Air
V16 Model No.: PSQ-08-01 PSQ-10-01 PSQ-12-01 8,000/10,000/12,000 BTU Portable Air Conditioner Operating Instructions
…
iCongo PSQ-08-01(18 pages) |
Frigidaire
READ BEFORE INSTALLING UNITFor Through-the-Wall Air ConditionersTo avoid risk of personal injury, property damage, or product damage due to the weight of this device and sharpedges that may be exposed:Air conditioners covered in this manual pose an excessive weight hazard. Two or more people are needed tomove and install the unit. To prevent injury or strain …
CRA086HT10(14 pages) |
Gree
MANUEL DU PROPRIÉTAIREMerci de choisir notre climatiseur. Lisez attentivement ce manuel avantd’utiliser le climatiseur et conservez-le à des fins de référence.GWC09MB-D3DN *****KGWC12MB-D3DN *****KGWC18MC-D3DN *****KGWC24MD-D3DN *****KGWH09MB-D3DN *****KGWH12MB-D3DN *****KGWH18MC-D3DN *****KGWH24MD-D3DN *****K00762_30/05/2016© Tous droits réservés, …
GWC09MB-D3DNK Series(38 pages) |
Samsung
Air conditionerInstallation manualAJ***TXJ*KH• Thank you for purchasing this Samsung air conditioner.• Before operating this unit, please read this manual carefully and retain it for future reference.DB68-09261A-01
…
AJ TXJ KH Series(36 pages) |
GE
Safety Instructions ............. 2, 3Recycle Information ...................3Operating InstructionsControls ...........................4–6Care and CleaningAir Filter ..............................7Outdoor Coils .........................7Installation Instructions ...... 8-11Troubleshooting Tips ............12 Normal Operating Sounds ............12Consumer …
AEZ05 and(28 pages) |
BenQ Projector MP727 - XGA DLP Projector#92GC8S: MP727 - XGA DLP Projector Projector Operation & user’s manual MP727 - XGA DLP Projector, 71 |
ACTiSYS Computer Accessories ACT-IR3200MACTiSYS ACT-IR3200M User Guide (Operation & user’s manual), @31RQG3 ACT-IR3200M, 24 |
Sportwerks Toy MayhemAssembly and operation manual for Sportwerks Mayhem Toy Mayhem, 40 |
Philips Monitor 220VW8Monitor PDF Uživatelská příručka 220VW8, 89 |
Tappan Cooktop TEF324WHSACooktop PDF Owner's manual TEF324WHSA, 16 |
Tripp Lite Surge Protector PM6NS#O3EDBD PM6NS: Tripp Lite Surge Protector Owner Documentation PM6NS, 3 |
Biamp Amplifier VOCIA VA-8600#XKW7M2: VOCIA VA-8600 Amplifier Manual VOCIA VA-8600, 17 |
Gibson Freezer GFU09M2AW7Freezer #15B782 GFU09M2AW7, 12 |
Lightolier Indoor Furnishing 23MHRSIndoor Furnishing #86E6KW 23MHRS, 1 |
Fellowes Paper Shredder POWERSHRED DS-2Paper Shredder Instructions manual (Fellowes POWERSHRED DS-2) POWERSHRED DS-2, 8 |
NEC Server Express 5800Server Operation & user’s manual (NEC Express 5800) Express 5800, 116 |
JUKI Sewing Machine LU-2216N-7Sewing Machine #6IMJZT LU-2216N-7, 4 |